Search NASA⌕ Search

SEARCH · Search NASA

Results for “shock wave experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Study of the H + O + M reaction forming OH{sup *}: Kinetics of OH{sup *} chemiluminescence in hydrogen combustion systems

The temporal variation of OH{sup *} (A{sup 2}{sigma}{sup +}) chemiluminescence in hydrogen oxidation chemistry has been studied in a shock tube behind reflected shock waves at temperatures of 1400-3300 K and at a pressure of 1 bar. The aim of the present work is to obtain a validated reaction scheme to describe OH{sup *} formation in the H{sub 2}/O{sub 2} system. Temporal OH{sup *} emission profiles and ignition delay times for lean and stoichiometric H{sub 2}/O{sub 2} mixtures diluted in 97-98% argon were obtained from the shock-tube experiments. Based on a literature review for the hydrogen combustion system, the key reaction considered was H + O + M = OH{sup *} + M. The temperature dependence of the measured peak OH{sup *} emission from the shock tube and the peak OH{sup *} concentration from a homogeneous closed reactor model are compared. Based on these results a reaction rate coefficient of k{sub 1} = (1.5 {+-} 0.4) x 10{sup 13} exp(-25 kJ mol{sup -1}/RT) cm{sup 6} mol{sup -2} s{sup -1} was found for the forward reaction which is slightly higher than the rate coefficient suggested by Hidaka et al. (1982). The comparison of measured and simulated absolute concentrations shows good agreement. Additionally, a one-dimensional laminar premixed low-pressure flame calculation was performed for where absolute OH{sup *} concentration measurements have been reported by Smith et al. (2005). The absolute peak OH{sup *} concentration is fairly well reproduced if the above mentioned rate coefficient is used in the simulation. (author)

08 HYDROGEN↗

Sound velocities in highly oriented pyrolytic graphite shocked to 18 GPa: Orientational order dependence and elastic instability

Previous reports of rapid phase transformation above 18 GPa [Erskine and Nellis, Nature 349, 317 (1991)] and large elastic waves below 18 GPa [Lucas et al., J. Appl. Phys. 114, 093515 (2013)] for shock-compressed ZYB-grade highly-oriented pyrolytic graphite (HOPG), but not for less oriented ZYH-grade HOPG, indicated a link between the orientational order dependence of the HOPG response above and below the phase transformation stress. To gain insight into this link and into the mechanical response of HOPG shocked to peak stresses approaching the phase transformation onset, the compressibility of ZYB- and ZYH-grade HOPG in the shocked state was examined using front surface impact experiments. Particle velocity histories and sound velocities were measured for peak stresses reaching 18 GPa. Although the locus of the measured peak stress-particle velocity states is indistinguishable for the two grades of HOPG, the measured sound velocities in the peak state reveal significant differences between the two grades. Specifically, 1) The measured sound velocities are somewhat higher for ZYH-grade HOPG, compared to ZYB-grade HOPG. 2) The measured sound velocities for ZYH-grade HOPG increase smoothly with compression, whereas those for ZYB-2 grade HOPG exhibit a significant reduction in the compression dependence from 12 GPa to 17 GPa and an abrupt increase from 17 GPa to 18 GPa. 3) The longitudinal moduli, determined from the measured sound velocities, are smaller than the calculated bulk moduli for ZYB-grade HOPG shocked to peak stresses above 15 GPa, indicating the onset of an elastic instability. The present findings demonstrate that the softening of the longitudinal modulus (or elastic instability) presented here is linked to the large elastic waves and the rapid phase transformation reported previously – all observed only for shocked ZYB-grade HOPG. The elastic instability in shocked ZYB-grade HOPG is likely a precursor to the rapid phase transformation observed above 18 GPa for this HOPG grade.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Solar flare produced pulsations in meter and X-ray wavelengths

The mechanism responsible for the modulation of synchrotron radiation in the meter wave range by a solar flare is examined. The proposed explanation is based on the interaction of a flare generated shock front with a magnetic flux tube extending out into the corona over the flare. As the shock wave propagates through the flux tube, Alfven waves are developing and travelling up the tube toward each other, thereby accelerating electrons and protons by the Fermi mechanism and thus filling the top of the flux tube with energetic electrons. Radial oscillations develop as the shock front becomes parallel to the magnetic field direction and the intensity of the synchrotron radiation is modulated by these oscillations. An OSO-5 experiment detected a hard X-ray burst associated with the flare that produced modulated radio emission and X-ray modulations that are attributed to density fluctuations in the X-ray bursts.

Frost, K. J.↗

Magnetic field observations near Venus - Preliminary results from Mariner 10

The NASA-GSFC magnetic field experiment on Mariner 10 is the first flight of a dual magnetometer system conceived to permit accurate measurements of weak magnetic fields in space in the presence of a significant and variable spacecraft magnetic field. Results from a preliminary analysis of a limited data set are summarized in this report, which is restricted primarily to Venus encounter. A detached bow shock wave that develops as the super Alfvenic solar wind interacts with the Venusian atmosphere has been observed. However, the unique coincidence of trajectory position and interplanetary field orientation at the time of bow shock crossing led to a very disturbed shock profile with considerably enhanced upstream magnetic fluctuations. At present it is not possible to ascertain the nature and characteristics of the obstacle responsible for deflecting the solar wind flow. Far downstream disturbances associated with the solar wind wake have been observed.

Ness, N. F.↗

Computational Analyses in Support of Sub-scale Diffuser Testing for the A-3 Facility: Unsteady Analyses and Risk Assessment - Part 2

Simulation technology can play an important role in rocket engine test facility design and development by assessing risks, providing analysis of dynamic pressure and thermal loads, identifying failure modes and predicting anomalous behavior of critical systems. This is especially true for facilities such as the proposed A-3 facility at NASA SSC because of a challenging operating envelope linked to variable throttle conditions at relatively low chamber pressures. Design Support of the feasibility of operating conditions and procedures is critical in such cases due to the possibility of startup/shutdown transients, moving shock structures, unsteady shock-boundary layer interactions and engine and diffuser unstart modes that can result in catastrophic failure. Analyses of such systems is difficult due to resolution requirements needed to accurately capture moving shock structures, shock-boundary layer interactions, two-phase flow regimes and engine unstart modes. In a companion paper, we will demonstrate with the use of CFD, steady analyses advanced capability to evaluate supersonic diffuser and steam ejector performance in the sub-scale A-3 facility. In this paper we will address transient issues with the operation of the facility especially at startup and shutdown, and assess risks related to afterburning due to the interaction of a fuel rich plume with oxygen that is a by-product of the steam ejectors. The primary areas that will be addressed in this paper are: (1) analyses of unstart modes due to flow transients especially during startup/ignition, (2) engine safety during the shutdown process (3) interaction of steam ejectors with the primary plume i.e. flow transients as well as probability of afterburning. In this abstract we discuss unsteady analyses of the engine shutdown process. However, the final paper will include analyses of a staged startup, drawdown of the engine test cell pressure, and risk assessment of potential afterburning in the facility. Unsteady simulations have been carried out to study the engine shutdown process in the facility and understand the physics behind the interactions between the steam ejectors, the test cell and the supersonic diffuser. As a first approximation, to understand the dominant unsteady mechanisms in the engine test cell and the supersonic diffuser, the turning duct in the facility was removed. As the engine loses power a rarefaction wave travels downstream that disrupts the shock cell structure in the supersonic diffuser. Flow from the test cell is seen to expand into the supersonic diffuser section and re-pressurizes the area around the nozzle along with a upstream traveling compression wave that emanates from near the first stage ejectors. Flow from the first stage ejector expands to the center of the duct and a new shock train is formed between the first and second stage ejectors. Both stage ejectors keep the facility pressurized and prevent any large amplitude pressure fluctuations from affecting the engine nozzle. The resultant pressure loads the nozzle experiences in the shutdown process are small.

Ahuja, Vineet↗

Tandem spheres in hypersonic flow

The problem of determining the forces acting on a secondary body when it is travelling at some point within the shocked region created by a hypersonic primary body is of interest in such situations as store or stage separation, re-entry of multiple vehicles, and atmospheric meteoroid fragmentation. The current work is concerned with a special case of this problem, namely that in which both bodies are spheres and are stationary with respect to one another. We first present an approximate analytical model of the problem; subsequently, numerical simulations are described and results are compared with those from the analytical model. Finally, results are presented from a series of experiments in the T5 hypervelocity shock tunnel in which a newly-developed force-measurement technique was employed.

97 MATHEMATICS AND COMPUTING↗

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

Hypersonic Research Vehicle (HRV) real-time flight test support feasibility and requirements study. Part 1: Real-time flight experiment support

The results are presented of a study to identify potential real time remote computational applications to support monitoring HRV flight test experiments along with definitions of preliminary requirements. A major expansion of the support capability available at Ames-Dryden was considered. The focus is on the use of extensive computation and data bases together with real time flight data to generate and present high level information to those monitoring the flight. Six examples were considered: (1) boundary layer transition location; (2) shock wave position estimation; (3) performance estimation; (4) surface temperature estimation; (5) critical structural stress estimation; and (6) stability estimation.

Rediess, Herman A.↗

Auto-ignition of toluene-doped n-heptane and iso-octane/air mixtures: High-pressure shock-tube experiments and kinetics modeling

Toluene is often used as a fluorescent tracer for fuel concentration measurements, but without considering whether it affects the auto-ignition properties of the base fuel. We investigate the auto-ignition of pure toluene and its influence on the auto-ignition of n-heptane and iso-octane/air mixtures under engine-relevant conditions at typical tracer concentrations. Ignition delay times {tau}{sub ign} were measured behind reflected shock waves in mixtures with air at {phi}=1.0 and 0.5 at p=40 bar, over a temperature range of T=700-1200 K and compared to numerical results using two different mechanisms. Based on the models, information is derived about the relative influence of toluene on {tau}{sub ign} on the base fuels as function of temperature. For typical toluene tracer concentrations {<=}10%, the ignition delay time {tau}{sub ign} changes by less than 10% in the relevant pressure and temperature range. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Strength of porous α-SiO 2 in a shock loaded environment: Calibration via Richtmyer–Meshkov instability and validation via Mach lens

The strength of brittle porous media is of concern in numerous applications, for example, earth penetration, crater formation, and blast loading. Thus, it is of importance to possess techniques that allow for constitutive model calibration within the laboratory setting. The goal of the current work is to demonstrate an experimental technique allowing for strength assessment of porous media subjected to shock loading, which can be implemented into pressure-dependent yield surfaces within numerical simulation schemes. As a case study, the deviatoric response of distended α-SiO 2 has been captured in a tamped Richtmyer–Meshkov instability (RMI) environment at a pressure regime of 4–10 GPa. Hydrocode simulations were used to interpret RMI experimental data, and a resulting pressure-dependent yield surface akin to the often employed modified Drucker–Prager model was calibrated. Simulations indicate that the resulting jet length generated by the RMI is sensitive to the porous media strength, thereby providing a feasible experimental platform capable of capturing the pressurized granular deviatoric response. Furthermore, in efforts to validate the RMI-calibrated strength model, a set of Mach-lens experiments was performed and simulated with the calibrated pressure-dependent yield surface. Excellent agreement between the resulting Mach-lens length in experiment and simulation provides additional confidence to the RMI yield-surface calibration scheme.

36 MATERIALS SCIENCE↗

Novel method to control explosive shock sensitivity: Formulations, experiments and modeling

The microstructure of a heterogeneous high explosive (HE) affects its shock initiation sensitivity and detonation performance. Alteration of the void content and/or void structure (i.e., bulk heating or mechanical damage) therefore changes the shock initiation behavior. Controlling and predicting the change in shock sensitivity after an HE has undergone microstructural changes addresses an important and challenging goal for the design and understanding of novel energetic material formulations. In this study, we aimed to develop HE systems to precisely tune shock sensitivity by a thermal treatment prior to use. Specifically, we incorporated a small fraction (1 wt% or less) of thermally expandable microspheres (TEMs) during the formulation process of various plastic-bonded explosives (PBX). TEMs typically consist of a thermoplastic acrylonitrile shell (10-50 µm diameter), which encapsulates an inert low boiling hydrocarbon. Upon heating, the TEMs expand as the shell softens while the hydrocarbon gasifies, increasing the internal pressure and expanding the particle by as much as 120 vol% (irreversibly). Here, we present our progress on shock sensitivity comparisons of HE formulations doped with TEMs after heating and expansion. Experiments, using Composition C-4 thermally cycled to 120°C, showed an increase in shock sensitivity. Additionally, mesoscale modeling revealed that the TEM itself does not act as a hotspot, but instead has a secondary effect on the response of nearby voids. We conclude that TEMs indeed do provide a method to tune shock sensitivity. Further, our results emphasize the non-uniformity of shock waves at the mesoscale, and that upstream defects influence the reactivity of downstream defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High-pressure phase transitions of α-quartz under nonhydrostatic dynamic conditions: A reconnaissance study at PETRA III

Hypervelocity collisions of solid bodies occur frequently in the solar system and affect rocks by shock waves and dynamic loading. A range of shock metamorphic effects and high-pressure polymorphs in rock-forming minerals are known from meteorites and terrestrial impact craters. In this paper, we investigate the formation of high-pressure polymorphs of α-quartz under dynamic and nonhydrostatic conditions and compare these disequilibrium states with those predicted by phase diagrams derived from static experiments under equilibrium conditions. We create highly dynamic conditions utilizing a mDAC and study the phase transformations in α-quartz in situ by synchrotron powder X-ray diffraction. Phase transitions of α-quartz are studied at pressures up to 66.1 and different loading rates. At compression rates between 0.14 and 1.96 GPa s -1 , experiments reveal that α-quartz is amorphized and partially converted to stishovite between 20.7 GPa and 28.0 GPa. Therefore, coesite is not formed as would be expected from equilibrium conditions. With the increasing compression rate, a slight increase in the transition pressure occurs. The experiments show that dynamic compression causes an instantaneous formation of structures consisting only of SiO 6 octahedra rather than the rearrangement of the SiO 4 tetrahedra to form a coesite. Although shock compression rates are orders of magnitude faster, a similar mechanism could operate in impact events.

36 MATERIALS SCIENCE↗

Multi-shock design tools in double shell models

The essence of the project was to implement a program in python that demonstrated certain models put forth by fusion physicists. Across the time spent at Los Alamos National Laboratory, much was spent programming. Though fundamentally programmatical in nature, the task contained considerable difficulty hid within mathematically deriving and manipulating the models while maintaining data discretization. The result of solving these complications gave invaluable experience in applied mathematics. The final product, a piece of lengthy code, ended up having the full range of desired capabilities, with plans for more. Given the laser power history from a pulse shot on NIF, Omega, or any other Inertial Confinement Fusion facility, the code maps the terrain of radiation temperature inside the hohlraum throughout the period of the shot. Additionally, shock wave convergence prediction was implemented as additional capability. As the name of the project suggests, this tool acts as a compass of direction for researchers designing laser power profiles. Further development of this tool will undoubtedly assist in the research conducted on single and double-shell indirect ICF, consequently expanding the capabilities of operating stewardship over the national nuclear stockpile.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The University of Iowa Helios solar wind plasma wave experiment /E 5a/

This document describes the University of Iowa solar wind plasma wave experiment for the Helios missions (Experiment 5a). The objective of this experiment is the investigation of naturally occurring plasma instabilities and electromagnetic waves in the solar wind. To carry out this investigation, the experiment consists primarily of a 16-channel spectrum analyzer connected to the electric field antennas. The spectrum analyzer covers the frequency range from 20 Hz to 200 kHz and has an amplitude dynamic range which extends from .3 microvolts/m to 30 mV/m per channel. This spectrum analyzer, the antenna potential measurements, the shock alarm system and the supporting electronics are discussed in detail.

Gurnett, D. A.↗

Calculational investigation of impact cratering dynamics - Material motions during the crater growth period

The considered investigation was conducted in connection with studies which are to provide a better understanding of the detailed dynamics of impact cratering processes. Such an understanding is vital for a comprehension of planetary surfaces. The investigation is the continuation of a study of impact dynamics in a uniform, nongeologic material at impact velocities achievable in laboratory-scale experiments conducted by Thomsen et al. (1979). A calculation of a 6 km/sec impact of a 0.3 g spherical 2024 aluminum projectile into low strength (50 kPa) homogeneous plasticene clay has been continued from 18 microseconds to past 600 microseconds. The cratering flow field, defined as the material flow field in the target beyond the transient cavity but well behind the outgoing shock wave, has been analyzed in detail to see how applicable the Maxwell Z-Model, developed from analysis of near-surface explosion cratering calculations, is to impact cratering

Austin, M. G.↗

Swept shock/boundary layer interaction experiments in support of CFD code validation

Research on the topic of shock wave/turbulent boundary-layer interaction was carried out during the past three years at the Penn State Gas Dynamics Laboratory. This report describes the experimental research program which provides basic knowledge and establishes new data on heat transfer in swept shock wave/boundary-layer interactions. An equilibrium turbulent boundary-layer on a flat plate is subjected to impingement by swept planar shock waves generated by a sharp fin. Five different interactions with fin angle ranging from 10 deg to 20 deg at freestream Mach numbers of 3.0 and 4.0 produce a variety of interaction strengths from weak to very strong. A foil heater generates a uniform heat flux over the flat plate surface, and miniature thin-film-resistance sensors mounted on it are used to measure the local surface temperature. The heat convection equation is then solved for the heat transfer distribution within an interaction, yielding a total uncertainty of about +/- 10 percent. These experimental data are compared with the results of numerical Navier-Stokes solutions which employ a k-epsilon turbulence model. Finally, a simplified form of the peak heat transfer correlation for fin interactions is suggested.

Settles, G. S.↗

Analysis of the effects of energy deposition on shock-driven turbulent mixing

We perform simulations of laser-driven turbulence experiments with energy deposition, modeling situations where energy is deposited in a mixing layer before or after it is reshocked. Such situations are experienced in, e.g., inertial confinement fusion capsules. We show that the timing of the energy deposition has a significant impact on the development of turbulent flow and corresponding turbulent material mixing. In particular, if the energy is deposited before the shock wave begins interacting with the mixing layer, the development of turbulence and turbulent mixing are inhibited. If, however, the energy is deposited after the shock wave has interacted with a portion of the mixing layer, turbulence generation and turbulent mixing are enhanced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Density reconstruction in convergent high-energy-density systems using x-ray radiography and Bayesian inference

X-ray radiography is a technique frequently used to diagnose convergent high-energy-density (HED) systems, such as inertial confinement fusion implosion, and provides unique information that is not available through self-emission measurements. In this work, we investigate the scope and limits of that information using a radiography simulation combined with the Bayesian inference workflow. The accuracy of density reconstruction from simulated radiographs of spherical implosions driven with 27 kJ laser energy is assessed, including the increase or decrease in accuracy due to the addition of Lagrangian marker layers, Poisson noise, and improved prior information. This work is the first to present the full uncertainty distributions inferred from radiography analysis in HED systems and demonstrates the importance of constructing the full posterior probability density, as opposed to a point estimate, due to the modal structure of the likelihood surface introduced by typical experimental noise sources. This general methodology can be used both for robust analysis of radiographic data and for an improved design of radiography experiments by modeling the full experimental system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗