Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Structural and morphological studies on Bi{sub 1-x}Ca{sub x}MnO{sub 3} thin films grown by RF magnetron sputtering

Bi{sub 1-x}Ca{sub x}MnO{sub 3} (0 ≤ X ≤ 0.4) thin films are deposited on n–type Si (100) substrate at 800 °C by RF magnetron sputtering. X-ray diffraction pattern shows that the films are crystallized in monoclinic structure with C2 space group. The crystallite size and induced strain in the prepared films are measured by W-H plot. The cell parameters and texture coefficient of the films are calculated. The surface morphology of the films is examined by atomic force microscope. The study confirms the optimum level of calcium doping is 20 at. % in Bi site of BiMnO{sub 3} film, these findings pave the way for further research in the Ca modified BiMnO{sub 3} films towards device fabrication.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Doping Effect of Fe Ions on the Structural, Electrical, and Magnetic Properties of SrTiO{sub 3} Nanoceramic Matrix

In the present investigation, strontium titanate nanoceramic was synthesized by incorporating iron (Fe) ion with general formula SrTi{sub 1−x}Fe{sub x}O{sub 3} (x = 0.0, 0.1, 0.2, and 0.4) using sol-gel autocombustion method. The effect of Fe ions on the structural, morphological, electrical, dielectric, and magnetic properties of the prepared matrix has been investigated by various characterization techniques with the appropriate formulation. The structural properties such as phase space, crystallite size (D), and lattice parameter (a) of prepared matrix are calculated by X-ray diffraction (XRD) technique. The functional groups were analyzed by Fourier transform infrared spectroscopy (FT-IR). The surface morphology of the prepared nanoceramic matrix has been determined by using field emission scanning electron microscopy (FE-SEM) analysis. Calculation of average particle size and diffraction patterns was confirmed by using images from transmission electron microscopy (TEM) and selected area electron diffraction pattern (SAED), respectively. An energy dispersive spectrum analysis (EDS) confirmed the compositional stoichiometry in the investigated matrix. Electrical conductivity increased the prepared sample due to the increasing in the Fe concentration and temperature. The dielectric parameters in the frequency range of 30 Hz to 1 MHz were found higher at lower frequencies. The pure SrTiO{sub 3} matrix shows a paramagnetic nature at room temperature, but for a higher concentration of Fe doping was used to observe the weak ferromagnetic nature. Therefore, due to Fe ion concentration, the properties of the prepared matrix have been completely varied and enhancement in the magnetic properties was observed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The performance of a surface-applied corrosion inhibitor for the carbon steel in saturated Ca(OH){sub 2} solutions

In the present work, the performance of an amino alcohol based surface applied inhibitor was studied by the electrochemical techniques in saturated Ca(OH){sub 2} solutions. The surface morphology of the carbon steel was observed by scanning electron microscope, and the energy diffraction spectrum was also tested. Results showed that the inhibitor used in this work demonstrated obvious inhibition efficiency on the carbon steel in saturated Ca(OH){sub 2} solutions. The inhibition mechanism of the inhibitor lies in the quick adsorption of the active component on carbon steel surface.

36 MATERIALS SCIENCE↗

Imaging how thermal capillary waves and anisotropic interfacial stiffness shape nanoparticle supracrystals

Abstract Development of the surface morphology and shape of crystalline nanostructures governs the functionality of various materials, ranging from phonon transport to biocompatibility. However, the kinetic pathways, following which such development occurs, have been largely unexplored due to the lack of real-space imaging at single particle resolution. Here, we use colloidal nanoparticles assembling into supracrystals as a model system, and pinpoint the key role of surface fluctuation in shaping supracrystals. Utilizing liquid-phase transmission electron microscopy, we map the spatiotemporal surface profiles of supracrystals, which follow a capillary wave theory. Based on this theory, we measure otherwise elusive interfacial properties such as interfacial stiffness and mobility, the former of which demonstrates a remarkable dependence on the exposed facet of the supracrystal. The facet of lower surface energy is favored, consistent with the Wulff construction rule. Our imaging–analysis framework can be applicable to other phenomena, such as electrodeposition, nucleation, and membrane deformation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Melt Temperature on Surface Films Formed on Molten AZ91D Alloy Protected by Graphite Powder

Graphite powder was adopted to prevent AZ91D alloy from oxidizing during melting and casting. The microstructure of the resultant surface films, formed at 933 K, 973 K, 1013 K, and 1053 K (660 °C, 700 °C, 740 °C, and 780 °C) for 30 minutes, was investigated by scanning electron microscopy, energy dispersive spectrometer, and X-ray diffraction, and the phase composition of the surface films was analyzed by the standard Gibbs free energy change of the reactions between the graphite powder, the alloy melt, and the ambient atmosphere. The effect and mechanism of melt temperature on the resultant surface films were also discussed. The results indicated that the surface films, of which the surface morphology comprised folds and wrinkles, were composed of a protective layer and MgF{sub 2} particles. The protective layer was contributive to the prevention of the molten alloy from oxidizing, and consisted of magnesium, oxygen, fluorine, carbon, and a small amount of aluminium existing in the form of MgO, MgF{sub 2}, C, and MgAl{sub 2}O{sub 4}. The layer thickness was 200 to 900 nm. The melt temperature may affect the surface films through the increased interaction between the graphite powder, the melt, and the ambient atmosphere. The oxygen content and thickness of the protective layer decreased and then increased, while the height of the folds increased with melt temperature.

36 MATERIALS SCIENCE↗

Characterization of ZnO:SnO{sub 2} (50:50) thin film deposited by RF magnetron sputtering technique

Zinc oxide (ZnO) and tin oxide (SnO{sub 2}) thin films have attracted significant interest recently for use in optoelectronic application such as solar cells, flat panel displays, photonic devices, laser diodes and gas sensors because of their desirable electrical and optical properties and wide band gap. In the present study, thin films of ZnO:SnO{sub 2} (50:50) were deposited on pre-cleaned microscopic glass substrate by RF magnetron sputtering technique. The substrate temperature and RF power induced changes in structural, surface morphological, compositional and optical properties of the films have been studied.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation and visible-light activity of silver vanadate for the degradation of pollutants

Monoclinic structure silver vanadate Ag{sub 3}VO{sub 4} was prepared by hydrothermal process. The effects of the ratio of silver to vanadium in starting material, hydrothermal temperature on surface morphologies, structure and photoactivity of Ag{sub 3}VO{sub 4} for the decolorization azodye acid red B under visible irradiation were investigated. The Ag{sub 3}VO{sub 4} prepared in the excess vanadium at 160 deg. C for 48 h exhibited highest visible-light-driven activity. Excess vanadium in the preparation increased the crystallinity and suppressed the formation of grain boundaries, while the formation of Ag{sup 0} on the surface of the catalyst promoting the electron-hole separation and interfacial charge transfer, resulting in an increase in the photocatalytic activity. Furthermore, the activity of the Ag{sub 3}VO{sub 4} was increased by 11 times when NiO was loaded, which also shows high activities for the decomposition of phenol and aniline. It is possible due to the formation of a short-circuited microphotoelectrochemical cell enhancing the separation of photogenerated electron-hole pairs.

36 MATERIALS SCIENCE↗

Analysis of surface potential and magnetic properties of Fe{sub 3}O{sub 4}/graphene oxide nanocomposites

Nanocomposite of magnetite/graphene oxide (Fe{sub 3}O{sub 4}/GO) has been synthesized by co-precipitation method. The phase formation of the magnetite nanoparticles (Fe{sub 3}O{sub 4} NPs) was confirmed by X-ray diffraction (XRD) analysis. Effect of Fe{sub 3}O{sub 4} NPs on the Raman spectra and on the surface potential of GO has been analyzed. Due to incorporation of NPs, change in the characteristic Raman peaks and also on the surface potential of GO is observed. Transmission electron microscopic (TEM) study has been carried out for surface morphology. Magnetic property measurement was carried out by using physical property measurement system (PPMS) at two different temperatures (30 K and 300 K).

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Corrosion Behavior of Plasma-Nitrided 904L Austenitic Stainless Steel in Hydrofluoric Acid

A new type of high-chromium nickel molybdenum super austenitic stainless steel, 904L, has excellent corrosion resistance in acidic environments. However, the service life of 904L decreases significantly in a mixed acid system that includes hydrogen fluoride and sulfuric acid. In this article, different plasma nitriding processes were used to modify the surface of 904L stainless steel. X-ray diffraction was used to analyze the phase composition after nitriding; scanning electron microscopy and atomic force microscopy were used to examine the surface morphology after nitriding; electrochemical noise and electrochemical methods were used to study the localized corrosion behavior and the damage mechanism of the ion nitride layer; and the effect of the plasma nitride layer on the corrosion resistance was explored. The results show that with increasing nitriding time, the thickness of the nitride layer increased. Ion nitriding resulted in the coarsening of the 904L austenitic stainless steel surface. A long nitriding treatment time resulted in the precipitation of CrN in the modified layer, depleting the chromium from the matrix and remarkably reducing the corrosion resistance.

36 MATERIALS SCIENCE↗

CO{sub 2} Corrosion Behavior of Calcite-Covered API 5L X52 Carbon Steel in Aqueous Solutions

The CO{sub 2} corrosion of API 5L X52 steel in the presence and absence of calcite scale has been investigated. The scale was precipitated from a supersaturated solution at temperatures of 25 and 80 °C. The crystalline phase, cross section and surface morphologies of scale were studied by x-ray diffraction and scanning electron microscopy, respectively. It was found that the scale deposit mostly consisted of calcite. The corrosion behavior of bare and calcite-covered samples was investigated by electrochemical impedance spectroscopy and cyclic polarization techniques in aqueous CO{sub 2} solutions at 30, 50 and 70 °C. The presence of calcite scale on carbon steel surface decreased the adsorption of intermediate corrosion products as the scale uniformly covered the bare surface which resulted in reduction of general CO{sub 2} corrosion rate. The results of cyclic polarization tests revealed that the bare and calcite-covered samples were not susceptible to localized CO{sub 2} corrosion under conditions studied in this research.

36 MATERIALS SCIENCE↗

Combined electrocoagulation-microfiltration-membrane distillation for treatment of hydraulic fracturing produced water

Hydraulic fracturing flowback and produced water is a highly impaired wastewater containing dissolved salts polar and non-polar organic compounds, oil and surfactants. Here a combined electrocoagulation - microfiltration – membrane distillation process has been used to treat this wastewater. Electrocoagulation followed by microfiltration was used to pretreat the wastewater prior membrane distillation. The initial total dissolved solids (TDS) concentration was extremely high being 245,300 mg L -1 . After electrocoagulation, the total organic carbon (TOC) was reduced from 120 mg L -1 to 64 mg L -1 . Tangential flow microfiltration using a 0.1 μm pore size polyethersulfone membrane was used to separate the particulate matter after electrocoagulation and to further reduce the TOC to 44 mg L -1 . Membrane distillation was used to desalinate the pretreated produced water resulting in a high quality treated water (TDS of 56 mg L -1 and TOC 1 mg L -1 ). Three membranes with very different surface morphology were used: commercially available polyvinylidene fluoride, electrospun poly(vinylidene fluoride-co-hexafluoropropylene) nanofibers and multiwalled carbon nanotube coated polytetrafluoroethylene. The TDS in the retentate increased to over 350,000 mg L -1 . During membrane distillation, the temperature of the feed tank was maintained at 36 °C while the feed entered the module at 60 °C in order to minimize scaling on the membrane. The surface properties of an ideal membrane that is resistant to wetting and provides high flux is likely to depend on the TDS and properties of the wastewater.

42 ENGINEERING↗

Morphology and water-barrier properties of silane films on aluminum and silicon

The goal of this study is to understand the effect of the substrate on the morphology and water-barrier properties of bis-silane films. Silane films are deposited on both Si and Al. Neutron reflectivity is used to assess the effect of hydrothermal conditioning on the films. Aluminum on silicon (no silane) was characterized first to facilitate understanding of the more complicated silane on Al-coated Si. A 200-{angstrom} Al layer with 55-{angstrom} oxide covers the surface of the silicon wafer. The reflectivity data show that water penetrates into the oxide layer. Silane films deposited on either Al or Si substrates have similar bulk and top-surface morphology. Studies of silanes on Si wafers, therefore, can be generalized to include Al. The substrate-silane interface, however, does depend on both the substrate and the silane. Because pH of the bis-sulfur silane solution is outside of the stability range for Al{sub 2}O{sub 3}, dissolution of the thin oxide film occurs during solution deposition. A water-depletion area is formed at the interface region due to this reaction.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Laccase-mediated functionalization of chitosan with 4-hexyloxyphenol enhances antioxidant and hydrophobic properties of copolymer

In this paper, an effective method to functionalize chitosan with 4-hexyloxyphenol (HP) under homogeneous reaction conditions was developed using laccase as the catalyst. The resulting copolymer was characterized for chemical structure, grafted-HP content, surface morphology, thermal stability, antioxidant capacity, hydrophobic properties and tensile strength. Solid-state 13 C NMR spectrum confirmed the incorporation of HP onto chitosan. X-ray diffraction (XRD) showed a decrease in the degree of crystallinity for laccase/HP treated chitosan compared to pure chitosan. The grafted-HP content in laccase/HP-treated chitosan first increased and then declined with increase of the initial HP/chitosan ratio. A heterogeneous surface with spherical particles on the laccase/HP treated chitosan was observed by environmental scanning electron microscopy (ESEM) and scanning probe microscopy (SPM). The laccase/HP treatment of chitosan improved the thermal stability of copolymer. More significantly, the HP functionalized chitosan showed greatly improved ABTS + and DPPH radicals scavenging capacity, compared with pure chitosan. The hydrophobicity property of the HP functionalized chitosan also significantly increased although its tensile strength decreased. Finally, this new type of composite with double functionalities (i.e., antioxidant and hydrophobic) could potentially be used as food packaging materials or coating agents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Estimation of heat transfer coefficients for biomass particles by direct numerical simulation using microstructured particle models in the Laminar regime

Here, direct numerical simulation of convective heat transfer from hot gas to isolated biomass particle models with realistic morphology and explicit microstructure was performed over a range of conditions with laminar flow of hot gas (500 degrees C). Steady-state results demonstrated that convective interfacial heat transfer is dependent on the wood species. The computed heat transfer coefficients were shown to vary between the pine and aspen models by nearly 20%. These differences are attributed to the species-specific variations in the exterior surface morphology of the biomass particles. We also quantify variations in heat transfer experienced by the particle when positioned in different orientations with respect to the direction of fluid flow. These results are compared to previously reported heat transfer coefficient correlations in the range of 0.1 < Pr < 1.5 and 10 < Re < 500. Comparison of these simulation results to correlations commonly used in the literature (Gunn, Ranz-Marshall, and Bird-Stewart-Lightfoot) shows that the Ranz-Marshall (sphere) correlation gave the closest h values to our steady-state simulations for both wood species, though no existing correlation was within 20% of both species at all conditions studied. In general, this work exemplifies the fact that all biomass feedstocks are not created equal, and that their species-specific characteristics must be appreciated in order to facilitate accurate simulations of conversion processes.

09 BIOMASS FUELS↗

Surface Modification and Chemical Sputtering of Graphite Induced by Low Energy Atomic and Molecular Deuterium Ions

The surface morphology, and chemical/structural modifications induced during chemical sputtering of ATJ graphite by low-energy (<200 eV/D) deuterium atomic and molecular ions are explored by Scanning Electron Microscopy (SEM), Raman and Auger Electron Spectroscopy (AES) diagnostics. At the lowest impact energies, the ion range may become less than the probe depth of Raman and AES spectroscopy diagnostics. We show that such diagnostics are still useful probes at these energies. As demonstration, we used these surface diagnostics to confirm the characteristic changes of surface texture, increased amorphization, enhanced surface reactivity to impurity species, and increased sp{sup 3} content that low-energy deuterium ion bombardment to steady-state chemical sputtering conditions produces. To put these studies into proper context, we also present new chemical sputtering yields for methane production of ATJ graphite at room temperature by impact of D{sub 2}{sup +} in the energy range 10-250 eV/D, and by impact of D{sup +} and D{sub 3}{sup +} at 30 eV/D and 125 eV/D, obtained using a Quadrupole Mass Spectroscopy (QMS) approach. Below 100 eV/D, the methane production in ATJ graphite is larger than that in HOPG by a factor of {approx} 2. In the energy range 10-60 eV/D, the methane production yield is almost independent of energy and then decreases with increasing ion energies. The results are in good agreement with recent molecular dynamics simulations.

03 NATURAL GAS↗

Laser Nitriding of the Newly Developed Ti-20Nb-13Zr at.% Biomaterial Alloy to Enhance Its Mechanical and Corrosion Properties in Simulated Body Fluid

Despite the widespread application of Ti alloy in the biomedical field, surface treatments are typically applied to improve its resistance to corrosion and wear. A newly developed biomedical Ti-20Nb-13Zr at.% alloy (TNZ) was laser-treated in nitrogen environment to improve its surface characteristics with corrosion protection performance. Surface modification of the alloy by laser was performed through a Nd:YAG laser. The structural and surface morphological alterations in the laser nitrided layer were investigated by XRD and a FE-SEM. The mechanical properties have been evaluated using nanoindentation for laser nitride and as-received samples. The corrosion protection behavior was estimated using electrochemical corrosion analysis in a physiological medium (SBF). The obtained results revealed the production of a dense and compact film of TiN fine grains (micro-/nanosize) with 9.1 µm below the surface. The mechanical assessment results indicated an improvement in the modulus of elasticity, hardness, and resistance of the formed TiN layer to plastic deformation. The electrochemical analysis exhibited that the surface protection performance of the laser nitrided TNZ substrates in the SBF could be considerably enhanced compared to that of the as-received alloy due to the presence of fine grains in the TiN layer resulting from laser nitriding. Furthermore, the untreated and treated Ti-20Nb-13Zr alloy exhibited higher corrosion resistance than the CpTi and Ti6Al4V commercial alloys. The improvements in the surface hardness and corrosion properties of Ti alloy in a simulated body obtained using laser nitriding make this approach a suitable candidate for enhancing the properties of biomaterials.

36 MATERIALS SCIENCE↗

TUNING OF SIZE AND SHAPE OF AU-PT NANOCATALYST FOR DIRECT METHANOL FUEL CELLS

In this paper, we report the precise control of the size, shape and surface morphology of Au-Pt nanocatalysts (cubes, blocks, octahedrons and dogbones) synthesized via a seed-mediated approach. Gold 'seeds' of different aspect ratios (1 to 4.2), grown by a silver-assisted approach, were used as templates for high-yield production of novel Au-Pt nanocatalysts at a low temperature (40 C). Characterization by electron microscopy (SEM, TEM, HRTEM), energy dispersive X-ray analysis (EDX), UV-Vis spectroscopy, zeta-potential (surface charge), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma mass spectrometry (ICP-MS) were used to better understand their physico-chemical properties, preferred reactivities and underlying nanoparticle growth mechanism. A rotating disk electrode was used to evaluate the Au-Pt nanocatalysts electrochemical performance in the oxygen reduction reaction (ORR) and the methanol oxidation reaction (MOR) of direct methanol fuel cells. The results indicate the Au-Pt dogbones are partially and in some cases completely unaffected by methanol poisoning during the evaluation of the ORR. The ORR performance of the octahedron particles in the absence of MeOH is superior to that of the Au-Pt dogbones and Pt-black, however its performance is affected by the presence of MeOH.

10 SYNTHETIC FUELS↗