Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Morphological and electrochemical characterization of electrodeposited Zn–Ag nanoparticle composite coatings

Silver nanoparticles with an average size of 23 nm were chemically synthesized and used to fabricate Zn–Ag composite coatings. The Zn–Ag composite coatings were generated by electrodeposition method using a simple sulfate plating bath dispersed with 0.5, 1 and 1.5 g/l of Ag nanoparticles. Scanning electron microscopy, X-ray diffraction and texture co-efficient calculations revealed that Ag nanoparticles appreciably influenced the morphology, micro-structure and texture of the deposit. It was also noticed that agglomerates of Ag nanoparticles, in the case of high bath load conditions, produced defects and dislocations on the deposit surface. Ag nanoparticles altered the corrosion resistance property of Zn–Ag composite coatings as observed from Tafel polarization, electrochemical impedance analysis and an immersion test. Reduction in corrosion rate with increased charge transfer resistance was observed for Zn–Ag composite coatings when compared to a pure Zn coating. However, the particle concentration in the plating bath and their agglomeration state directly influenced the surface morphology and the subsequent corrosion behavior of the deposits. - Highlights: • Synthesis of Ag nanoparticles with an average size of 23 nm • Fabrication of Zn/nano Ag composite coating on mild steel • Composite coatings showed better corrosion resistance. • Optimization of particle concentration is necessary.

36 MATERIALS SCIENCE↗

Multilayered vacuum-arc nanocomposite TiN/ZrN coatings before and after annealing: Structure, properties, first-principles calculations

Highlights: • Multilayer TiN/ZrN films were deposited using sequential vacuum-arc deposition of Ti and Zr targets in nitrogen atmosphere; • Several samples were annealed in air at the temperature 700 °C; • First-principles calculations of TiN(111), ZrN(111) structures and TiN(111)/ZrN(111) multilayer were carried out; • All deposited samples were highly polycrystalline with quite large 20–25 nm crystals; • The nanohardness and elastic modulus of non-annealed coatings reached 42 GPa and 348 GPa, respectively; • Deposited coatings demonstrate good wear and oxidation resistance; - Abstract: Nanoscale multilayered TiN/ZrN films were deposited using sequential vacuum-arc deposition of Ti and Zr targets in a nitrogen atmosphere. Studies of film's properties were carried out using various modern methods of analysis, such as XRD, STEM, HRTEM, SIMS combined with results of nanoindentation and tribological tests. To interpret the mechanical properties of the deposited multilayer films first-principles calculations of TiN(111), ZrN(111) structures and TiN(111)/ZrN(111) multilayer were carried out. To study the influence of thermal annealing, several samples were annealed in air at the temperature 700 °C. All deposited samples were highly polycrystalline with quite large 20–25 nm crystals. The crystalline planes were very ordinated and demonstrated an excellent coordinated growth. The nanohardness and elastic modulus of non-annealed coatings reached 42 GPa and 348 GPa, respectively. Annealing in air at the temperature 700 °C led to partial oxidation of the multilayered coatings, however hardness of the non-oxidized part of the coatings remained as high, as for initial coatings. All deposited coatings demonstrate good wear resistance.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructure detection of Mg-Zi-Ti-Si amorphous composite coating prepared by SMAT

Highlights: • The Mg-Zn-Ti-Si amorphous composite coating was prepared on Mg alloy via SMAT. • Except for amorphous portion, the phases of coating include Zn, Mg{sub 7}Zn{sub 3}, and Si. • The coating was thick and rough but it was well combined with the matrix. • During SMAT, the matrix surface was also strengthened because of solid-solution and grain refinement. - Abstract: The Mg-Zn-Ti-Si coating was prepared on Mg alloy through surface mechanical attrition treatment (SMAT) which was simple and low-cost. The microstructure and phase composition of coating were detected through a scanning electron microscope (SEM), an X-ray diffractometer (XRD) and a high resolution transmission electron microscope (HRTEM). The results demonstrated that the layer thickness, which depended on the rotation speed, was 20–80 μm. Although the coating was rough, it was well combined with the matrix. The XRD pattern and HRTEM image analysis demonstrated that the coating contained both amorphous and crystalline phases (Zn, Mg{sub 7}Zn{sub 3} and Si). The process also led to matrix surface strengthening; the mechanisms are solid solution and grain refinement.

36 MATERIALS SCIENCE↗

Glassy carbon formation from pyrolysis of polymeric coatings on fiber-optic sensors

Deploying fiber-optic sensors in nuclear reactors requires a detailed understanding of radiation effects on the fiber materials and the transmitted signals. Previous work has shown large wavelength shifts in the reflected spectra obtained from polymer-coated fiber-optic temperature sensors exposed to high neutron fluences. The sensor drift resulting from these wavelength shifts cannot be explained by radiation effects on fused silica glass. These shifts are hypothesized to be caused by the conversion of the polymeric fiber coating to a glassy carbon via radiolysis and/or pyrolysis and subsequent radiation-induced compaction. Here, thermal degradation of these polymeric coatings was studied to provide insight into the potential origins of the sensor drift phenomenon. Acrylate- and polyimide-coated fibers were heated under various temperatures (250–1300 °C) and environments (oxidative and inert), and the resulting coating products were characterized via mass-loss data, scanning electron microscope imaging, and Raman spectroscopy. Results suggest that the polymer decomposition product of both coating types, at least under inert conditions, is indeed a glassy carbon. Analytical models that account for radiation-induced glassy carbon coating compaction show significant compressive fiber strains and predicted wavelength shifts that agree well with experimental measurements, providing additional evidence that supports the hypothesized origins of the sensor drift.

36 MATERIALS SCIENCE↗

Electrodeposited composite coating of Ni-W-P with nano-sized rod- and spherical-shaped SiC particles

In this research, Ni-W-P-SiC nanocomposite coatings are electrodeposited from the plating solution containing suspension of nano-sized spherical- and rod-shaped SiC particles. The influence of SiC particle charge, applied current density, surfactant addition and the particle shape on the SiC incorporation rate has been studied. The phase structure, microhardness and wear resistance of Ni-W-P-SiC nanocomposite coatings were evaluated using X-ray diffraction (XRD), microhardness tester and wear test apparatus. The surface morphology of the produced coatings and worn surfaces has been investigated using scanning electron microscope (SEM). Additionally, the composite coating exhibited higher hardness and wear resistance than the pure Ni-W-P alloy. Regardless the particle shape, the mechanical characteristics of composite coatings are improved with increasing of SiC wt.% into the matrix. The corrosion behavior of the produced coatings was studied using anodic polarization measurements. The nanocomposite coating incorporating SiC rods exhibited higher mechanical and corrosion performance compared with deposits with spherical SiC nano-particles.

36 MATERIALS SCIENCE↗

Simple coating synthesis and enhanced luminescence behaviour of LiLa(MoO4)2:Eu3+@NaF

Highlights: • LiLa(MoO{sub 4}){sub 2}:Eu{sup 3+}{sub 0.06} @ (NaF){sub y wt} were synthesized with a simple coating method. • PL intensity can be enhanced as high as 4.80 times by coating NaF. • Enhancement PL intensity is a major effect, and increasing R is a minor effect. • LiLa(MoO{sub 4}){sub 2}:Eu{sup 3+}{sub 0.06} @ (NaF){sub 0.025 wt} was a phosphor with high R values (R = 5.89). - Abstract: A series of LiLa(MoO{sub 4}){sub 2}:Eu{sup 3+}@ (NaF){sub y wt} were prepared with a simple coating method. XRD results confirm that NaF coating will cause the slight expand of the lattice volume for the sample. Strongly enhanced emission effect inducing by NaF coating is observed. The emission spectra (PL) intensity of the optimal sample, LiLa(MoO{sub 4}){sub 2}:Eu{sup 3+}{sub 0.06} @ (NaF){sub 0.025wt} is as high as 4.8 times of that of LiLa(MoO{sub 4}){sub 2}:Eu{sup 3+}{sub 0.06}. Furthermore, dual emission properties inducing by NaF coating are observed. Enhancement emission of Eu{sup 3+} is a major effect, and increasing R is a minor effect. The optimal coating content of NaF is 2.5 wt%, which the corresponding chromaticity coordinates excited at 465 nm is x = 0.6650, y = 0.3347, which is nearly as same as the NTSC (National Television Standard Committee) standard values for red (x = 0.67, y = 0.33). So, it is a potential red-emitting phosphor with high R values (R = 5.89) for blue light-based white LED.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Depth-resolved residual stress analysis of thin coatings by a new FIB-DIC method

A new methodology for the measurement of depth sensitive residual stress profiles of thin coatings with sub-micrometer resolution is presented. The two step method consists of incremental focused ion beam (FIB) ring-core milling, combined with high-resolution in situ SEM-FEG imaging of the relaxing surface and a full field strain analysis by digital image correlation (DIC). The through-thickness profile of the residual stress can be obtained by comparison of the experimentally measured surface strain with finite element modeling using Schajer's integral method. In this work, a chromium nitride (CrN) CAE-PVD 3.0 {mu}m coating on steel substrate, and a gold MS-PVD 1.5 {mu}m on silicon were selected for the experimental implementation. Incremental FIB milling was conducted using an optimized milling strategy that produces minimum re-deposition over the sample surface. Results showed an average residual stress of {sigma} = -5.15 GPa in the CrN coating and {sigma} = +194 MPa in the Au coating. These values are in reasonable agreement with estimates obtained by other conventional techniques. The depth profiles revealed an increasing residual stress from surface to the coating/surface interface for both coatings. This observation is likely related to stress relaxation during grain growth, which was observed in microstructural cross sections, as predicted by existing models for structure-stress evolution in PVD coatings. A correlation between the observed stress gradients and the in-service mechanical behavior of the coatings is proposed. Finally, critical aspects of the technique and the influence of microstructure and elastic anisotropy on stress analysis are analyzed and discussed.

36 MATERIALS SCIENCE↗

Toward a high-voltage fast-charging pouch cell with TiO 2 cathode coating and enhanced battery safety

Nickel-rich layered lithium transition metal oxides, LiNi x Co y Mn 1-x-y O 2 , are key cathode materials for high-energy lithium-ion batteries owing to their high specific capacity. However, the commercial deployment of nickel-rich oxides has been hampered by their poor thermostability and insufficient cycle life. In this work full batteries with uncoated and TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathodes and graphite anodes are compared in terms of electrochemical performance and safety behavior. The battery using a TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode exhibited better cyclic performance at high cutoff voltage. Electrochemical impedance spectroscopy analysis indicated that the TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode gave the battery a more stable charge transfer resistance. Transmission electron microscopy demonstrated that TiO 2 coating reduced accumulation of the cathode electrolyte interface layer on the particle surface. Time-of-flight secondary ion mass spectrometry demonstrated that TiO 2 coating markedly enhanced the interface stability of the cathode particle and protected the particle from serious etching by the electrolyte. Accelerating rate calorimetry revealed that the trigger temperature of thermal runaway for the battery using TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 as cathode material was 257 °C, which was higher than that of the battery with the uncoated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode (251 °C). In situ X-ray diffraction during heating demonstrated that this enhanced safety can be attributed to the suppressed phase evolution of the coated cathode material.

25 ENERGY STORAGE↗

APS TBC performance on directionally-solidified superalloy substrates with HVOF NiCoCrAlYHfSi bond coatings

Directionally-solidified (DS) superalloy components with advanced thermal barrier coatings (TBC) to lower the metal operating temperature have the potential to replace more expensive single crystal superalloys for large land-based turbines. In order to assess relative TBC performance, furnace cyclic testing was used with superalloys 1483, X4 and Hf-rich DS 247 substrates and high velocity oxygen fuel (HVOF)-NiCoCrAlYHfSi bond coatings at 1100 °C with 1-h cycles in air with 10% H 2 O. With these coating and test conditions, there was no statistically-significant effect of substrate alloy on the average lifetime of the air plasma sprayed (APS) yttria-stabilized zirconia (YSZ) top coatings on small coupons. Using photo-stimulated luminescence piezospectroscopy maps at regular cycling intervals, the residual compressive stress in the α-Al 2 O 3 scale underneath the YSZ top coating and on a bare bond coating was similar for all three substrates and delaminations occurred at roughly the same rate and frequency. As a result, x-ray fluorescence (XRF) measurements collected from the bare bond coating surface revealed higher Ti interdiffusion occurring with the 1483 substrate, which contained the highest Ti content.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of varying gelatin coating concentrations on RANKL induced osteoclastogenesis

Here, we assessed the effects of varying concentrations of gelatin coating on Receptor Activator of Nuclear Factor κ-B Ligand (RANKL)-induced RAW264.7 murine macrophage differentiation into osteoclast (OC) via osteoclastogenesis. The microstructures of coating surfaces with different concentrations of gelatin were examined by scanning electron microscopy and atomic force microscopy. Increased gelatin coating concentrations led to decreased gel rigidity but increased surface adhesion force attenuated OC differentiation and the decreased actin ring formation in RANKL-induced osteoclastogenesis. The decreased actin ring formation is associated with decreased lysosomal-associated membrane protein 1 (LAMP1) activity and bone resorption in the differentiated OCs with different gelatin coating concentrations as compared to the cells differentiated without gelatin coatings. In addition, increasing concentrations of gelatin coating attenuated the medium TGF-β1 protein levels and the expression levels of TGF-β and type-I (R1) and type-II (R2) TGF-β receptors in OCs, suggesting the gelatin-induced suppression of TGF-β signaling for the regulation of RNAKL-induced OC differentiation. Taken together, these findings showed that changes in gelatin coating concentrations, which were associated with altered gel thickness and substrate rigidity, might attenuate TGF-β signaling events to modulate OC differentiation and concomitant actin ring formation and bone matrix resorption in RANKL-induced osteoclastogenesis.

60 APPLIED LIFE SCIENCES↗

Influence of viscoelastic property on laser-generated surface acoustic waves in coating-substrate systems

Taking account of the viscoelasticity of materials, the pulsed laser generation of surface acoustic waves in coating-substrate systems has been investigated quantitatively by using the finite element method. The displacement spectra of the surface acoustic waves have been calculated in frequency domain for different coating-substrate systems, in which the viscoelastic properties of the coatings and substrates are considered separately. Meanwhile, the temporal displacement waveforms have been obtained by applying inverse fast Fourier transforms. The numerical results of the normal surface displacements are presented for different configurations: a single plate, a slow coating on a fast substrate, and a fast coating on a slow substrate. The influences of the viscoelastic properties of the coating and the substrate on the attenuation of the surface acoustic waves have been studied. In addition, the influence of the coating thickness on the attenuation of the surface acoustic waves has been also investigated in detail.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Radiation pressure efficiency measurements of nanoparticle coated microspheres

Experimental measurements of the radiation pressure efficiency (Q{sub pr}) for several microparticles have been compared to theoretical calculations extrapolated from the Bohren-Huffman code for Mie scattering of coated particles. An increased shift of the Q{sub pr} parameter was observed for 2 μm SiO{sub 2} core particles coated with nanoparticles of higher refractive indices. Coatings of 14 nm melamine particles were found to increase the Q{sub pr} parameter 135 times over similar coatings using SiO{sub 2} particles of the same size. While a coating of 100 nm polystyrene particles also showed a significant increase, they did not agree well with theoretical values. It is hypothesized that other factors such as increased scatter, drag, and finite coating coverage are no longer negligible for coatings using nanoparticles in this size regime.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Transforming dielectric coated tungsten and platinum wires to gaseous state using negative nanosecond-pulsed-current in vacuum

With the help of thin dielectric coatings, corona free explosions were achieved in the region of about half a wire length (2 cm) for tungsten wires and nearly the whole wire length for platinum wires under a fast rising (46–170 A/ns) negative polarity current in vacuum. Expansion velocity of the tungsten gas was over 10 km/s. Current waveforms from exploding coated wires were similar to those from bare wires in the air including a current pause stage. Coated wires with different coating parameters had a similar joule energy deposition before voltage collapsed, but a quite different scenario in the region near the electrodes. The axial field under negative current was the main reason for the axial inhomogeneity of coated tungsten wires. Tungsten or platinum gases in the vaporized region were tightly encompassed by the dielectric coating, while gaps or probably low density gases, were observed between the coating and the edge of the dense wire core in the core-corona structure region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of addition of Ag nano powder on mechanical properties of epoxy/polyaminoamide adduct coatings filled with conducting polymer

In this study the effect of Ag Nano powder on mechanical properties of epoxy coatings filled with optimized ratio of conducting polymers (Polyaniline and Polyppyrole) was evaluated. Bisphenol A diglycidyl ether epoxy resin (DGEBA) along with polyaminoamide adduct (ARADUR 3282-1 BD) is used as curing agent under optimized stoichiometry values. Curing is performed at room temperature with different percentages of Nano filler. Glass and steel panels were used as coating substrate. Bird applicator was used to coat the samples in order to obtain thin film with wet film thickness (WFT) of about 70-90 µm. The samples were kept in dust free environment for about 7 days at room temperature for complete curing. The coated steel panels were used to evaluate the mechanical properties of coating such as hardness, scratch and impact tests whereas coated glass panels were used for measuring pendulum hardness of the coatings. To check the dispersion and morphology of Nano filler in epoxy matrix scanning electron microscopy (SEM) was used in addition Nano indentation was also performed to observe the effect of Nano filler on modulus of elasticity and hardness at Nano scale.

36 MATERIALS SCIENCE↗

Structure and high temperature oxidation of mechanical alloyed Fe-Al coating

The structure and high temperature oxidation resistance of Fe-Al coating on low carbon steel were investigated. The Fe-Al coating was deposited on the surface of low carbon steel using a mechanical alloying method. The coating was then annealed at 600°C for 2 hour in a vacuum of 5 Pa. The cyclic-oxidation tests of low carbon steel, Fe-Al coatings with and without annealing were performed at 600°C for up to 60h in air. The structure of oxidized samples was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy X-ray spectroscopy (EDS). The results show that the Fe-Al coatings exhibit high oxidation resistance compared to the uncoated steel. After 60 h exposure, the uncoated steel formed mainly Fe{sub 3}O{sub 4} and Fe{sub 2}O{sub 3} layers with the total thickness of around 75.93 µm. Fe-Al coating without annealing formed a thin oxide layer, probably (Fe,Al){sub 2}O{sub 3}. Meanwhile, for annealed sample, EDX analysis observed the formation of two Fe-Al layers with difference in elements concentration. The obtained results suggest that the deposition of Fe-Al coating on low carbon steel can improve the oxidation resistance of low carbon steel.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dynamically morphing microchannels in liquid crystal elastomer coatings containing disclinations

Liquid crystal elastomers (LCEs) hold a major promise as a versatile material platform for smart soft coatings, since their orientational order can be predesigned to program a desired dynamic profile. In this work, we introduce temperature-responsive dynamic coatings based on LCEs with arrays of singular defects-disclinations that run parallel to the surface. The disclinations form in response to antagonistic patterns of the molecular orientation at the top and bottom surfaces, imposed by the plasmonic mask photoalignment. Upon heating, an initially flat LCE coating develops linear microchannels located above each disclination. The stimulus that causes a non-flat profile of LCE coatings upon heating is the activation force induced by the gradients of molecular orientation around disclinations. To describe the formation of microchannels and their thermal response, we adopt a Frank-Oseen model of disclinations in patterned director field and propose a linear elasticity theory to connect the complex spatially-varying molecular orientation to the displacements of the LCE. The thermo-responsive surface profiles predicted by the theory and by the finite element modeling are in good agreement with the experimental data; in particular, higher gradients of molecular orientation produce a stronger modulation of the coating profile. The elastic theory and the finite element simulations allow us to estimate the material parameter that characterizes the elastomer coating’s response to the thermal activation. The disclinations containing LCEs show potential as soft dynamic coatings with a predesigned responsive surface profile.

36 MATERIALS SCIENCE↗

Comparative study of alkali-vapour cells with alkane-, alkeneand 1-nonadecylbenzene-based antirelaxation wall coatings

The dependence of both longitudinal and transverse relaxation times of ground-state magnetic polarisation in alkali atoms on the coating temperature is experimentally studied for the first time in a rubidium-vapour cell with 1-nonadecylbenzene antirelaxation coating of inner walls. The comparison of these times with the relaxation times in a caesium-vapour cell with alkane wall coatings is presented. It is found that within the studied temperature range (294 – 340K) the transverse relaxation time decreases with increasing temperature of alkene and 1-nonadecylbenzene coatings. For the alkane coating such a dependence was not explicitly found. The longitudinal relaxation time begins to decrease in all cases when passing a certain critical temperature of the coating material. It is found that the unsaturated radical structure of the coating material molecules strongly affects its antirelaxation properties. (optical pumping)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Residual stress analysis of multilayer environmental barrier coatings.

Silicon-based ceramics (SiC, Si{sub 3}N{sub 4}) are promising materials systems for high-temperature structural applications in gas turbine engines. However, the silica layer that forms on these materials is susceptible to attack from water vapor present in combustion environments. To protect against this degradation, environmental barrier coatings (EBCs) have been developed to shield the underlying substrate and prevent degradation. Here we report on elastic and thermal properties, as well as internal stresses of candidate multilayer coatings, as measured in situ using microfocused high-energy X-rays in a transmission diffraction geometry. Doped aluminosilicate coatings were investigated for their stability on a SiC/SiC melt-infiltrated substrate. The coatings consisted of a Ba{sub 1-x}Sr{sub x}Al{sub 2}Si{sub 2}O{sub 8} topcoat with a mullite or mullite+SrAl{sub 2}Si{sub 2}O{sub 8} interlayer, and a silicon bond coat. A numerical model was used to compare the stress results with an ideal coating system. Experiments were carried out on as-sprayed and heat-treated samples in order to analyze the strain and phase evolution as a function of multilayer depth and temperature. The phase transformation of the topcoat promoted healing of cracks in the EBC and reduced stresses in the underlying layers and the addition of SAS to the interlayer reduced stresses in thermally cycled coatings, but did not stop cracks from forming.

33 ADVANCED PROPULSION SYSTEMS↗