Results for “Commercial Providers” — Page 52

DOE OSTI2022

Anticorrosive epoxy coatings from direct epoxidation of bioethanol fractionated lignin

The development of lignin-based anticorrosive epoxy coatings for steel protection is beneficial for both alleviating the fossil resource depletion and value-added utilization of lignin but remains a challenge due to the inherent heterogeneous structure of lignin. Here, in this study, we selectively extract the low molecular weight (MW) fraction of a crop residue-derived enzymatic hydrolysis lignin (EHL) through a bioethanol fractionation process and prepare epoxy resin by direct epoxidation of the bioethanol fractionated lignin (BFL). The coatings are then fabricated using 20–100 wt% of BFL-based epoxy resin (LEp) as the commercial epoxy resin substitute. The low MW and high p-hydroxyphenyl content of the BFL offer high solubility and good workability for BFL and LEp during epoxidation and coating production, respectively. Lignin-based coatings with 20–40 wt% LEp exhibit good adhesion property (5B) and superior corrosion resistance, compared to the commercial epoxy coating. Although coating with high LEp concentrations (i.e., 60–100 wt%) resulted in decreased adhesion strength, the coating with 100 wt% LEp still displayed corrosion protection performance comparable to that of the commercial epoxy coating. Overall, this study provides a simple and effective approach to converting lignin to epoxy resins for a wide variety of surface coating applications.

09 BIOMASS FUELS↗

DOE OSTI2026

Comprehensive structural characterization of charged polymers involved in moisture-driven direct air capture

This study provides a comprehensive structural characterization of commercially available alkaline anion-exchange polymers (Fumasep FAA-3 and IRA 900) used in moisture-driven direct air capture (DAC) of carbon dioxide. Using X-ray diffraction, SAXS/WAXS, atomic force microscopy, FIB-SEM, and transmission electron microscopy, the authors identify nanoscale clustering, porosity, swelling behavior, and humidity-dependent structural changes that influence CO₂ adsorption and release. These findings establish structure–function relationships critical for designing more durable and energy-efficient DAC polymer materials.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Elucidation of Active Sites in Aldol Condensation of Acetone over Single-Facet Dominant Anatase TiO 2 (101) and (001) Catalysts

Aldol condensations of carbonyl compounds for C–C bond formation are a very important class of reactions in organic synthesis and upgrading of biomass-derived feedstocks. However, the atomic level understanding of reaction mechanisms and structure-activity correlation on widely used transition metal oxide catalysts are limited due to the high degree of struc-tural heterogeneity of catalysts such as commercial TiO 2 powders. Here, we provide a deep understanding of the reaction mechanisms, kinetics, and structure–function relationships for vapor phase acetone aldol condensation through the con-trolled synthesis of two catalysts with high surface areas and clean, dominant facets, coupled with detailed characterization and kinetic studies that are further assisted by density functional theory (DFT) calculations. Temperature-dependent diffuse reflectance infrared Fourier transform spectroscopy showed the existence of abundant acetone bonded to surface hydroxyl groups (acetone-O s H) and acetone bonded to Lewis acid sites (acetone-Ti 5c ) on surface of both {101} and {001} facet dom-inant TiO 2 . Intermolecular C–C coupling of enolate intermediate from acetone-Ti 5c and a vicinal acetone-O s H is a kinetically relevant step, which is consistent with kinetic and isotopic studies and DFT calculations. The {001} facet showed a lower apparent activation energy (or higher reactivity) than the {101} facet. This is likely caused by the weaker Lewis acid and Brønsted base strengths of the {001} facet which favors the reprotonation–desorption of the coupled intermediate, making the C–C coupling step more exothermic on the {001} facet and resulting in an earlier transition state with a lower activation barrier. It is also possible that the {001} facet has a smoother surface configuration and less steric hindrance during intermo-lecular C–C bond formation than the {101} facet.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Leveraging Fine-Grained Occupancy Estimation Patterns for Effective HVAC Control

As occupancy sensing technologies become mature, various occupancy sensors are increasingly deployed in commercial buildings for pervasive occupancy monitoring. These sensors provide occupant-count data, which contains rich spatiotemporal information about occupancy patterns. With long-term occupant-count data collected from a commercial building, we design three different predictive models that capture the occupancy dynamics and examine how a model predictive control of the HVAC system benefits from actual occupancy count prediction. Our analysis reveals that mispredictions of occupancy states, especially false positives and false negatives, may introduce inefficient control that leads to energy waste or user discomfort. To address this issue, we take a step further to design an adaptive model predictive controller that minimizes inefficient control actions according to misprediction types and distributions. A comprehensive evaluation is performed in OpenBuild and EnergyPlus simulators to study the effectiveness of the proposed end-to-end control strategy. The evaluation shows that the proposed solution reduces energy consumption by 29.5% while improving the average weighted occupants comfort by 86.7% in Predicted Mean Vote (PMV) over the fixed schedule strategy.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2026

Travel Decision Survey - San Francisco - 2013

On behalf of the San Francisco Municipal Transportation Agency (SFMTA), Corey, Canapary & Galanis undertook a Travel Decision Survey within the City and County of San Francisco, as well as the eight surrounding Bay Area counties of Alameda, Contra Costa, San Mateo, Marin, Santa Clara, Napa, Sonoma, and Solano. The primary goals of this study were to: 1. Assess percent mode share for travel in San Francisco for evaluation of the SFMTA Strategic Objective 2.3: Mode Share target of 50% non-private auto travel by FY 2018 with a 95% confidence level and margin of error ±5% or less. 2. Evaluate the above statement based on number of trips to, from, and within San Francisco by Bay Area residents. Trips by visitors to the Bay Area and for commercial purposes are not included. 3. Provide additional trip details, including trip purpose for each trip in the mode-share question series. 4. Collect demographic data on the population of Bay Area residents who travel to, from, and within San Francisco. 5. Collect data on travel behavior and opinions that support other SFMTA strategy and project evaluation needs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2026

Travel Decision Survey - San Francisco - 2014

On behalf of the San Francisco Municipal Transportation Agency (SFMTA), Corey, Canapary & Galanis undertook a Travel Decision Survey within the City and County of San Francisco, as well as the eight surrounding Bay Area counties of Alameda, Contra Costa, San Mateo, Marin, Santa Clara, Napa, Sonoma, and Solano. The primary goals of this study were to: 1. Assess percent mode share for travel in San Francisco for evaluation of the SFMTA Strategic Objective 2.3: Mode Share target of 50% non-private auto travel by FY 2018 with a 95% confidence level and margin of error ±5% or less. 2. Evaluate the above statement based on number of trips to, from, and within San Francisco by Bay Area residents. Trips by visitors to the Bay Area and for commercial purposes are not included. 3. Provide additional trip details, including trip purpose for each trip in the mode-share question series. 4. Collect demographic data on the population of Bay Area residents who travel to, from, and within San Francisco. 5. Collect data on travel behavior and opinions that support other SFMTA strategy and project evaluation needs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2026

Travel Decision Survey - San Francisco - 2015

On behalf of the San Francisco Municipal Transportation Agency (SFMTA), Corey, Canapary & Galanis undertook a Travel Decision Survey within the City and County of San Francisco, as well as the eight surrounding Bay Area counties of Alameda, Contra Costa, San Mateo, Marin, Santa Clara, Napa, Sonoma, and Solano. The primary goals of this study were to: 1. Assess percent mode share for travel in San Francisco for evaluation of the SFMTA Strategic Objective 2.3: Mode Share target of 50% non-private auto travel by FY 2018 with a 95% confidence level and margin of error ±5% or less. 2. Evaluate the above statement based on number of trips to, from, and within San Francisco by Bay Area residents. Trips by visitors to the Bay Area and for commercial purposes are not included. 3. Provide additional trip details, including trip purpose for each trip in the mode-share question series. 4. Collect demographic data on the population of Bay Area residents who travel to, from, and within San Francisco. 5. Collect data on travel behavior and opinions that support other SFMTA strategy and project evaluation needs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2026

Travel Decision Survey - San Francisco - 2017

On behalf of the San Francisco Municipal Transportation Agency (SFMTA), Corey, Canapary & Galanis undertook a Travel Decision Survey within the City and County of San Francisco, as well as the eight surrounding Bay Area counties of Alameda, Contra Costa, San Mateo, Marin, Santa Clara, Napa, Sonoma, and Solano. The primary goals of this study were to: 1. Assess percent mode share for travel in San Francisco for evaluation of the SFMTA Strategic Objective 2.3: Mode Share target of 50% non-private auto travel by FY 2018 with a 95% confidence level and margin of error ±5% or less. 2. Evaluate the above statement based on number of trips to, from, and within San Francisco by Bay Area residents. Trips by visitors to the Bay Area and for commercial purposes are not included. 3. Provide additional trip details, including trip purpose for each trip in the mode-share question series. 4. Collect demographic data on the population of Bay Area residents who travel to, from, and within San Francisco. 5. Collect data on travel behavior and opinions that support other SFMTA strategy and project evaluation needs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2022

Detecting Passing Valves at Scale Across Different Buildings and Systems: A Brick Enabled and Mortar Tested Application

Heating hot water distribution systems are typically used in commercial buildings to condition spaces to provide occupant thermal comfort. However, recent research shows significant distribution losses within these systems that drive down the overall hot water plant efficiency. This research focuses on detecting passing valves in reheat coils found in variable air volume (VAV) terminal units to reduce distribution losses. A passing valve allows hot water flow when the actuator on the valve is commanded to be closed. The fluid causes unintentional heating or cooling to occur, causing comfort and control issues, and wasting energy. We developed the passing valve detection algorithm using a framework based on the Brick schema and Mortar platform to ensure that the application is portable and can scale to many buildings. We applied the same application to analyze 1,335 VAV reheat terminal units in 20 buildings. The diversity found in these large datasets increases confidence that any building with VAV reheat terminal units with the required sensors and Brick data model can run our open-source algorithm with little or no modification. In aggregate, 5% of VAV units analyzed were categorized as having a sensor fault, 14% with potential passing valve fault, and 81% with no faults detected. However, there is a significant variation in the proportion of VAV units with a passing valve detected (1% to 83%) of each building’s analyzed units.

Roa, Carlos Duarte↗

DOE OSTI2021

Increasing melt efficiency and secondary alloy usage in aluminum die casting

In this project, the focus was to develop thermodynamic and kinetic models for the aluminum melting process involving secondary alloys, refractory materials and flux materials. The major research outcome of this study is 1) the refractory composition of CaO (8-12%), microsilica (1-3%), BaSO 4 and/or BaO (no more than 5%), B 2 O 3 (5%) and Al 2 O 3 (balance) effectively reduced the reactions with liquid Al and alloying/impurity elements and heat transfer during melting and holding process. 2) a flux composition of NaCl-KCl-(1-10%)KAlF 4 exhibited an effective covering effect and prevented the dross formation during melting of Al process. 3) A high Fe (0.44%) content recycled Al alloy with compatible mechanical properties was developed based on the impurities control methods, which provides great potential to replace the commercial structural alloys from primary Al and increase the usage of secondary alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2023

NDA Tech: Multimodal Data Fusion with 3D Gamma-Ray Imaging for Safeguards

The ultimate project goal is to improve quantitative results obtained by the IAEA with the H420 gamma ray imager. Distribution to the IAEA will be through incorporation of project results into the software provided with the device by our commercial partner, H3D, Inc. Toward achieving that goal, we have started discussions with H3D to identify the requisite software components and how they will mesh with their own internally developed contextual data systems and other extant software components. We have identified the coded-aperture response data cube as a key structure. Discussions on contextual imaging were informative but somewhat inconclusive as the project lead on contextual data (LBNL) has not been available.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Considerations for Improving the Technoeconomic Viability of Heat Pipe Microreactors by Employing a Functional Containment Approach

The economic cost of a microreactor is being investigated by leveraging MARVEL cost information in conjunction with some simplified design and analysis activities to present a hypothetical, yet feasible, option for investigation. This bottom-up cost estimate for a hypothetical commercial microreactor will be used to provide guidance to the industry and research communities regarding where priorities should be set to improve the viability of broad microreactor deployment. To support the design and analysis activities required to present a feasible option, some understanding of maximum accidental radionuclide releases and consequences is needed to provide bounding estimates on containment or confinement systems for radionuclide retention. To estimate fission product barrier and retention performance, a gaussian plume dose and dispersion model is employed, with isotopic inventories being propagated between barriers assuming conservative fractional release rates. Demonstrably conservative meteorological assumptions are also assumed. Standard reference release rates are assumed where safety requirements could be easily and economically employed. Results are provided in units of total effective dose equivalent as a function of distance from the release (i.e., the reactor). Initial results indicate that the hypothetical microreactor will likely need to credit the fuel cladding and at least one other barrier, or combination of barriers, to ensure public health and safety as required during a postulated accident. This approach is referred to as “functional containment,” since no single barrier will be relied upon for satisfying regulatory requirements and fundamental safety functions for radionuclide retention. Finally, a set of barrier options are provided so that future economic analyses can select the most viable design path.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Overview on Current Activities of Conduction-Cooled SRF Accelerators and their Applications

When Nb3Sn was reintroduced to the SRF community as an alternative to pure niobium, one key motivation has been to reduce the cryogenic requirements of new and existing accelerators by shifting from 2 K to 4 K operation. Meanwhile, a variety of implementations beyond research machines are being explored. The combination of Nb3Sn with conventional cryocoolers, enabling cryogen-free operation, has paved the way for the development of compact, standalone systems suitable for applications far beyond research, such as enhancing the durability of synthetics via crosslinking or sterilizing food and medical equipment, as well as environmental cleanup when it comes to decontaminating liquid and solid waste material. So, while fundamental R&D continues to refine Nb3Sn resonators, exploring improvements such as replacing the niobium substrate with copper, parallel research efforts are investigating how the increased beam power provided by SRF could expand the commercial use of electron beams. This presentation aims to deliver a comprehensive overview of ongoing research efforts to harness the benefits of SRF through Nb3Sn and conduction cooling.

Vennekate, John [Thomas Jefferson National Acceler↗

DOE OSTI2026

U.S. Marine Energy Technology Overview and Opportunities

Marine energy has the potential to power 57% of U.S. electrical needs. During this presentation, an overview of marine energy technologies, including wave energy, tidal energy, and ocean thermal energy conversion (OTEC) will be provided to better understand how its commercial maturation and deployment can support U.S. and global energy demand.

16 TIDAL AND WAVE POWER↗

DOE OSTI2025

Diversity of Sordariales Fungi: Identification of Seven New Species of Naviculisporaceae Through Morphological Analyses and Genome Sequencing

Thanks to next-generation sequencing (NGS) technologies, the diversity of fungi can now be investigated through the analysis of their genome sequences. Naviculisporaceae is a family within the Sordariales, whose diversity is not well-known, with only one genome sequence published for this family. Here, we report on the isolation and cultivation of 20 new strains of Naviculisporaceae. Their genome sequences, as well as those of the five commercially available strains, were determined, thus providing complete genome sequences for 25 new Naviculisporaceae strains. Species delimitation was conducted using a combination of (1) ITS + LSU phylogenetic analysis of the new isolates along with other known species of the family, (2) comparisons between DNA barcode sequences of the new strains with those of the known species, and (3) average genome-wide nucleotide identity calculation. We built a phylogenomic tree and studied the organization of the mating-type locus. In vitro fruiting was obtained for 16 strains, enabling the definition of seven new species, namely Pseudorhypophila gallica, Pseudorhypophila guyanensis Rhypophila alpibus, Rhypophila brasiliensis, Rhypophila camarguensis, Rhypophila reunionensis and Rhypophila thailandica, as well as two new combinations, namely Pseudorhypophila latipes and Pseudorhypophila oryzae. Eight strains for which in vitro fruiting was not obtained may belong to additional new species. These results expand the known diversity of the Naviculisporaceae and greatly enlarge the genomic data available for the family.

Naviculisporaceae↗

DOE OSTI2025

Fiber-Coupled Multipass NIR Sensor for In Situ, Real-Time Water Vapor Outgassing Monitoring

This work presents the recent development of a fiber-coupled multipass near-infrared (NIR) gas sensor used to monitor water vapor desorption of small material coupons. The gas sensor design employs a White cell topology to maximize the optical path length over a compact, hand-size footprint. Water vapor concentrations are quantified over a large dynamic range by simultaneously applying wavelength modulation and tunable diode laser absorption spectroscopy techniques. A custom headspace optimized for material desorption experiments is assembled using commercially available vacuum chamber components. We provide in situ measurements of water vapor desorption from two geometries of the industrially important silicone elastomer Sylgard-184 as a case study for sensor viability. To corroborate the results, the gas sensor data are compared to numerical simulations based on a triple-mode diffusion–sorption model, consisting of Henry, Langmuir, and Pooling modes.

gas sensor↗

DOE OSTI2026

Value of Geothermal Energy Storage for Supply-Side and Demand-Side Applications

This report presents the results of a study examining the value potential for geothermal energy storage (GES), a long-duration energy storage resource that stores thermal and/or geomechanical energy in the subsurface. GES could benefit the overall U.S. power system by temporally shifting electricity generation (supply-side) or meeting building heating and cooling load (demand-side). This report analyzes supply-side and demand-side opportunities independently because of differences in applications and models. Currently there is significant uncertainty about the development costs for GES, with only a limited number of demonstration plants for electric energy storage and building heating and cooling storage developments. In this report, we estimate the value of supply-side and demand-side GES to the bulk power system in the contiguous United States. Because of the significant uncertainty about GES development costs, this analysis does not consider GES deployment costs but instead focuses on the value of GES to the U.S. electricity system. The estimated values of GES provide reference points for economically competitive commercial cost targets. Supply-side GES is modeled as part of an enhanced geothermal system (EGS) generation plant in NREL's Regional Energy Deployment System (ReEDS) capacity expansion model (Ho et al. 2021). In contrast to conventional geothermal plants, which generate constant power, EGS plants have unique features that may allow for in-reservoir energy storage for flexible generation. Demand-side GES for heating and cooling, including seasonal hot and cold storage and short-duration heat pump storage, is incorporated into a price-taker model using Cambium electricity marginal cost projections. To establish an upper bound for the value of GES, analysis focused on favorable scenarios for storage with high generation from zero marginal cost, variable renewable energy resources. High penetrations of variable renewable energy generation can increase hourly electricity price variability, which increases the value of temporal energy arbitrage for storage technologies like GES.

15 GEOTHERMAL ENERGY↗

NASA NTRS1969

Tape reading fixture

Commercially available roller type desk pad provides an efficient and orderly manner of handling rolled paper tapes for proofreading. The fixture, which is modified to accept Flex-O-Writer or similar tapes and roll them in either direction, reduces the chance of damaging or soiling the tapes through repeated handling.

Source record↗