Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressive Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Effect of low-speed impact damage and damage location on behavior of composite panels

The effect of low speed impact damage on the compression and tension strength of thin and moderately thick composite specimens was investigated. Impact speed ranged from 50 to 550 ft./sec., with corresponding impact energies from 0.25 to 30.7 ft. x lb. Impact locations were near the center of the specimen or near a lateral unloaded edge. In this study, thin specimens with only 90 degree and + or - 45 degree plies that were impacted away from the unloaded edge suffered less reduction in load carrying capability because of impact damage than of the same specimens impacted near the unloaded edge. Failure loads of thicker compression loaded specimens with a similar stacking sequence were independent of impact location. Failure loads of thin tension loaded specimens with 0 degree plies was independent of impact location, whereas failure loads of thicker compression loaded specimens with 0 degree plies were dependent upon impact location. A finite element analysis indicated that high axial strains occurred near the unloaded edges of the postbuckled panels. Thus, impacts near the unloaded edge would significantly affect the behavior of the postbuckled panel.

Jegley, Dawn C.↗
NASA NTRS1986

Combined bearing and bypass loading on a graphite/epoxy laminate

A combined experimental and analytical study was conducted to determine the behavior of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Single-fastener quasi-isotropic specimens were loaded at various bearing-bypass ratios until damage was produced at the fastener hole. Damage-onset strengths and damage modes were then analyzed using local hole-boundary stresses calculated by a finite-element analysis. The tension data showed the expected linear interaction for combined bearing and bypass loading with damage developing in the net-section tension mode. However, the compression bearing-bypass strengths showed an unexpected interaction involving the bearing mode. Compressive bypass loads reduced the bearing strength by decreasing the bolt-hole contact arc and thus increasing the severity of the bearing loads. The bearing stresses at the hole boundary were not accurately estimated by superposition of the stress components for separate bearing and bypass loading. However, superposition produced reasonably accurate estimates for tangential stresses especially near the specimen net-section.

Crews, J. H., Jr.↗
NASA NTRS1991

Indigenous lunar construction materials

The utilization of local resources for the construction and operation of a lunar base can significantly reduce the cost of transporting materials and supplies from Earth. The feasibility of processing lunar regolith to form construction materials and structural components is investigated. A preliminary review of potential processing methods such as sintering, hot-pressing, liquification, and cast basalt techniques, was completed. The processing method proposed is a variation on the cast basalt technique. It involves liquification of the regolith at 1200-1300 C, casting the liquid into a form, and controlled cooling. While the process temperature is higher than that for sintering or hot-pressing (1000-1100 C), this method is expected to yield a true engineering material with low variability in properties, high strength, and the potential to form large structural components. A scenario for this processing method was integrated with a design for a representative lunar base structure and potential construction techniques. The lunar shelter design is for a modular, segmented, pressurized, hemispherical dome which could serve as habitation and laboratory space. Based on this design, estimates of requirements for power, processing equipment, and construction equipment were made. This proposed combination of material processing method, structural design, and support requirements will help to establish the feasibility of lunar base construction using indigenous materials. Future work will refine the steps of the processing method. Specific areas where more information is needed are: furnace characteristics in vacuum; heat transfer during liquification; viscosity, pouring and forming behavior of molten regolith; design of high temperature forms; heat transfer during cooling; recrystallization of basalt; and refinement of estimates of elastic moduli, compressive and tensile strength, thermal expansion coefficient, thermal conductivity, and heat capacity. The preliminary design of the lunar shelter showed us that joining is a critical technology needed for building a structure from large segments. The problem of joining is important to the design of any structure that is not completely prefabricated. It is especially important when the structure is subjected to tensile loading by an internal pressure. For a lunar shelter constructed from large segments the joints between these large segments must be strong, and they must permit automated construction. With a cast basalt building material which is brittle, there is the additional problem of connecting the joint with the material and avoiding stress concentration that would cause failure. Thus, a well-defined project which we intend to pursue during this coming year is the design of joints for cast basalt structural elements.

Rogers, Wayne P.↗
DOE OSTI2021

High resolution >40 keV x-ray radiography using an edge-on micro-flag backlighter at NIF-ARC

Radiography of low-contrast features in high-density materials evolving on a nanosecond timescale requires a bright photon source in the tens of keV range with high temporal and spatial resolution. One application for sources in this category is the study of dynamic material strength in samples compressed to Mbar pressures at the National Ignition Facility, high-resolution measurements of plastic deformation under conditions relevant to meteor impacts, geophysics, armor development, and inertial confinement fusion. Here, we present radiographic data and the modulation transfer function (MTF) analysis of a multi-component test object probed at ~100 keV effective backlighter energy using a 5 μm-thin dysprosium foil driven by the NIF Advanced Radiographic Capability (ARC) short-pulse laser (~2 kJ, 10 ps). The thin edge of the foil acts as a bright line-projection source of hard x rays, which images the test object at 13.2× magnification into a filtered and shielded image plate detector stack. The system demonstrates a superior contrast of shallow (5 μm amplitude) sinusoidal ripples on gold samples up to 90 μm thick as well as enhanced spatial and temporal resolution using only a small fraction of the laser energy compared to an existing long-pulse-driven backlighter used routinely at the NIF for dynamic strength experiments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2019

Self-healing, re-adhering, and carbon-steel corrosion mitigating properties of fly ash-containing calcium aluminum phosphate cement composite at 300 °C hydrothermal temperature

This study assesses here the ability of calcium aluminate phosphate (CAP)/fly ash F (FAF) blend composite to self-heal at early age; to re-adhere to the casing surfaces after debonding and to protect carbon steel (CS) against brine-caused corrosion before and after the re-adherence. The composite was damaged after autoclaving for 24 h at 300 °C and then exposed to the same conditions for 5 more days for the self-healing and re-adhering processes. The ability of the blend to self-heal and re-adhere to CS was evaluated 1) by measurements of the recovery of compressive and bond strengths and Young's modulus; 2) by performing the 3-dimensional micro-image analysis of sealed cracks; 3) by phase identification in composite matrix and in the cracks after the healing; 4) by measurements of CS corrosion impediment by the re-adhered composite after 300°C-5-day restoration period. After the healing, the two factors, sealing effect of cracks by reaction products and change in phase composition of cement matrix, essentially governed the recovery of the original mechanical strength. For the former, analcime phase derived from pozzolanic FAF autogenous healing aid played the major role in sealing the cracks, while the well-formed hydroxyapatite phase contributed to the latter factor. The lap-shear bond with the strength of 1.11 MPa at CS plate/composite adhesive/CS plate joint failed cohesively, showing higher bond strength than strength of the composite matrix. The rebonded composite-CS plates developed a 0.37 MPa bond strength after the 5-day restoration period. The results of electrochemical polarization corrosion tests revealed that the re-adhered composite covering CS plate significantly inhibited the brine-caused corrosion of CS, leading to 0.011 mm/year corrosion rate, corresponding to 50% reduction compared with that of before re-adhering. There were two factors governing such corrosion mitigation: enhanced adhesive contact of composite with CS and increased coverage by the re-adhering composite.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Generation of high-intensity ultrasound through shock propagation in liquid jets

We investigated the generation and propagation of ultrasonic pressure waves produced by focused x-ray free-electron laser pulses in 14 to 30 μm diameter liquid water microjets. The pressure waves formed through reflections, at the surface of the microjets, of the initial shock launched in the liquid by the x-ray pulse. These waves developed a characteristic geometric pattern which is related to, but different from, the shock structures of supersonic gas jets. Fully developed waves had initial peak pressures ranging from less than –24 MPa to approximately 100 MPa, which exceed the compressive and tensile strengths of many materials, and correspond to extreme sound intensities on the order of 1 GW/m 2 and sound pressure levels above 270 dB (re: 1 μ Pa). The amplitudes and intensities were limited by the wave destroying its own propagation medium though cavitation, and therefore these ultrasonic waves in jets are one of the most intense propagating sounds that can be generated in liquid water. The pressure of the initial shock decayed exponentially, more rapidly in thinner jets, and the decay length was proportional to the jet diameter within the accuracy of measurements. Extrapolating our results to thinner jets, we find that the pressure waves may damage protein crystals carried by liquid jets in x-ray laser crystallography experiments conducted at megahertz repetition rates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

From broadband biphotons to frequency combs via spectral compression with time-varying cavities

Biphoton frequency combs are promising resources for quantum networking due in large part to their compatibility with the telecommunication infrastructure. Here, in this work, we propose a method to periodically compress broadband frequency-entangled photons into biphoton frequency combs by utilizing time-varying linear cavities. Our approach hinges on rapid modulation of the input cavity coupling, yielding high spectral purity in each output comb line similar to that achieved with narrowband filters, but without the associated loss in flux. We examine the dependence of spectral purity and compression on coupling strength, cavity loss, and switching speed, finding realistic regimes supporting purities in excess of 0.999 and peak enhancement factors of 100× and beyond.

Myilswamy, Karthik V. [Purdue Univ., West Lafayett↗
NASA NTRS1970

Materials, and engineering problems

Composite material engineering problems, discussing tensile, compressive and shear strengths, design approaches, unidirectional properties and substance characterizations

Dow, N. F.↗
NASA NTRS1974

Fabrication and testing of prestressed composite rotor blade spar specimens

Prestressed composite spar specimens were fabricated and evaluated by crack propagation and ballistic penetration tests. The crack propagation tests on flawed specimens showed that the prestressed composite spar construction significantly suppresses crack growth. Damage from three high velocity 30 caliber projectile hits was confined to three small holes in the ballistic test specimen. No fragmentation or crack propagation was observed indicating good ballistic damage resistance. Rotor attachment approaches and improved structural performance configurations were identified. Design theory was verified by tests. The prestressed composite spar configuration consisted of a compressively prestressed high strength ARDEFORM 301 stainless steel liner overwrapped with pretensioned S-994 fiberglass.

Gleich, D.↗
NASA NTRS1978

Effect of shelf aging on O-ring materials

Commercial O-rings made from 13 different rubber compounds were tested for physical properties after 7 and 12 years of shelf aging. No gross changes were observed in tensile strength, elongation, or compression deflection characteristics.

Wood, T. E.↗
NASA NTRS1982

High temperature composites for advanced missile and space transportation systems

A study has been conducted to characterize a state-of-the-art graphite/polyimide composite system by determining mechanical and thermophysical properties of selected laminates over a temperature range of -250 F to 600 F. The material studied was Celion 3000/PMR-15. Material property data obtained from testing included tension, compression and shear strengths, and coefficient of thermal expansion. Environmental conditions examined were: as cured/post-cured, isothermal aged at 600 F, thermal cycled from -250 F to 600 F, and moisture conditioned. This study has provided an initial data base on a graphite/polyimide composite system capable of operating in 500/600 F applications.

Mccleskey, S. F.↗
NASA NTRS1983

Failure mechanisms

Data, charts, and graphs relating to longitudinal tension, crack growth modes in unidirectional composites, strength predictions, and compression are given.

Hahn, H. T.↗
NASA NTRS1984

Elevated temperature compressive steady state deformation and failure in the oxide dispersion strengthened alloy MA 6000E

The compressive flow strength-strain rate behavior of the oxide-dispersion-strengthened alloy MA 6000E has been studied in the temperature range 1144-1366 K, with strain rates ranging from 2.1 x 10 to the -5th to 2.1 x 10 to the -7th per s. It is found that the inherent strength of the alloy is essentially the same in all test directions and that the low strength observed in tensile tests results from the inability of grain boundaries to support high tensile stresses. The failure of MA 6000E under high-temperature, slow plastic flow conditions is shown to be the result of concentrated slip. Slow plastic deformation in MA 6000E can be described by a threshold stress model of creep where threshold stresses are calculated from relatively fast testing procedures and the effective stress exponent for creep is assumed to be 3.5.

Whittenberger, J. D.↗
NASA NTRS1987

Use of reinforced inorganic cement materials for spark wire and drift chamber wire frames

The results of a survey, materials test, and analysis study directed toward the development of an inorganic glass-fiber reinforced cement material for use in the construction of space qualified spark wire frames and drift chamber frames are presented. The purpose for this research was to evaluate the feasibility of using glass fiber reinforced cement (GFRC) for large dimensioned structural frames for supporting a number of precisely located spark wires in multiple planes. A survey of the current state of the art in fiber reinforced cement materials was made; material sample mixes were made and tested to determine their laboratory performances. Tests conducted on sample materials showed that compressive and flexural strengths of this material could approach values which would enable fabrication of structural spark wire frames.

Source record↗
NASA NTRS1989

Microsandwich Honeycombs

In new type of honeycomb panel called "microsandwich honeycomb," walls filled with solid plastic foam reinforced with microspheres. Have compressive and shear strengths 50 to 70 percent greater than those of conventional, unfilled honeycombs of comparable dimensions and densities. Foam and hollow microspheres add little to weight but increase strength substantially. Useful in aircraft, automotive, and marine structures in which high strength and low weight important.

Bhat, Balakrishna↗
NASA NTRS1989

Mechanical properties of particulate composites based on a body-centered-cubic Mg-Li alloy containing boron

The effect of substituting the Mg metal in Mg-B composites by a Mg-14 wt pct Li solid solution on the ductility of the resulting composite was investigated using elastic modulus measurements on the P/M composite material prepared with a dispersion of B particles (in a vol pct range of 0-30) in a matrix of Mg-14 wt pct Li-1.5 wt pct Al. It was found that the elastic modulus of the composites increased rapidly with increasing boron, with specific stiffness values reaching about two times that of most structural materials. The values of the compression and tensile strengths increased significantly with boron additions. Good tensile ductility was achieved at the level of 10 vol pct B. However, at 20 vol pct B, the Mg-Li composite exhibited only limited tensile ductility (about 2 percent total elongation).

Whalen, R. T.↗
NASA NTRS1989

A test method to measure the response of composite materials under reversed cyclic loads

A test method to measure the response of composite materials under reversed cyclic loads is described. The method approximates the long-term response of a component by permitting the composite specimen to respond to the imposed loads and fail in an unconstrained mode rather than in a constrained mode. The method has been successfully used for the reversed cyclic loading of unnotched and notched graphite/epoxy and graphite/PEEK laminates of various stacking sequences. Included in the paper are monotonic tensile and compressive stiffness and strength data at several points in the fatigue lifetime, and damage development information obtained via X-ray radiography for quasi-isotropic T300/5208 and AS4/PEEK laminates with unloaded circular holes.

Bakis, Charles E.↗
NASA NTRS1990

Construction of the 16 meter Large Lunar Telescope (LLT)

The different materials that could be used to design the pedestal for a Moon based 16 meter telescope are discussed. The material that should be used has a low coefficient of thermal expansion, high modulus of elasticity, and high compressive and tensile strengths. For the model developed in this study, an aluminum-manganese alloy was used because of its low coefficient of thermal expansion. Due to variations in lunar soil conditions, both vertically and horizontally, three foundation systems are presented. The spudcan footing can be used in the case where dense soil is more than three meters. The spread footing is recommended where the dense soil is between one and three meters. Finally, in the third system, the Lunar Excursion Vehicle (LEV) is used as a base support for the telescope's pedestal. The LEV support requires a prepared site. The soil should be compacted and stabilized, if necessary, to reduce settlement.

Omar, Husam Anwar↗