Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dilute solution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Lignin content of Populus trichocarpa residues after CELF pretreatment and CBP fermentation

Here we present a dataset of lignin content from a woody energy crop (Populus trichocarpa) residues after a series of co-solvent enhanced lignocellulosic fractionation (CELF) pretreatment and consolidated bioprocessing (CBP) process. The natural poplar variant GW-9947 from the Center for Bioenergy Innovation (CBI) was used. The poplar was knife milled and passed through a 1 mm sieve and CELF pretreatment was performed in a Parr autoclave reactor with 7.5 wt % solids loading, 0.5 wt% H2SO4 as catalyst at 150°C with 5, 15, 25 and 30 minutes, respectively. Tetrahydrofuran was added in a 1:1 mass ratio with water as the pretreatment solvent. The residues from CELF pretreatment were then subjected to CBP using the bacterium C. thermocellum DSM 1313. CBP fermentations were performed at 60 °C in a shaker at 50, 75, and 100 grams/L solids loadings. The Klason lignin was measured using a two-step acid hydrolysis process. In brief, the poplar samples were first hydrolyzed by 72 wt% sulfuric acid at 30 oC for an hour. The hydrolysates were then diluted to 4 wt% sulfuric acid using deionized water and subsequently autoclaved at 121 oC for 1 h. Upon the completion of the two-step hydrolysis, the resulting solution was cooled to room temperature and the precipitate was then filtered through a G8 glass fiber filter through a crucible, dried at oven for overnight, and weighed to get the Klason lignin content. The lignin data provides information about lignin content changes after CELF and C. thermocellum CBP process.

Lignin Populus trichocarpa CELF pretreatment CBP f↗

Local structure in solid solutions of stabilised zirconia with actinide dioxides (UO{sub 2}, NpO{sub 2})

The local structure of (Zr,Lu,U)O{sub 2-x} and (Zr,Y,Np)O{sub 2-x} solid solutions has been investigated by extended X-ray absorption fine structure (EXAFS). Samples were prepared by mixing reactive (Zr,Lu)O{sub 2-x} and (Zr,Y)O{sub 2-x} precursor materials with the actinide oxide powders, respectively. Sintering at 1600 {sup o}C in Ar/H{sub 2} yields a fluorite structure with U(IV) and Np(IV). As typical for stabilised zirconia the metal-oxygen and metal-metal distances are characteristic for the different metal ions. The bond lengths increase with actinide concentration, whereas highest adaptation to the bulk stabilised zirconia structure was observed for U---O and Np---O bonds. The Zr---O bond shows only a slight increase from 2.14 A at 6 mol% actinide to 2.18 A at infinite dilution in UO{sub 2} and NpO{sub 2}. The short interatomic distance between Zr and the surrounding oxygen and metal atoms indicate a low relaxation of Zr with respect to the bulk structure, i.e. a strong Pauling behaviour. -- Graphical abstract: Metal-oxygen bond distances in (Zr,Lu,U)O{sub 2-x} solid solutions with different oxygen vacancy concentrations (Lu/Zr=1 and Lu/Zr=0.5). Display Omitted Research Highlights: {yields} EXAFS indicates high U and Np adaption to the bulk structure of stabilised zirconia. {yields} Zr---O bond length is 2.18 A at infinite Zr dilution in UO{sub 2} and NpO{sub 2}. {yields} Low relaxation (strong Pauling behaviour) of Zr explains its low solubility in UO{sub 2}.

36 MATERIALS SCIENCE↗

EFFECTIVENESS OF USING DILUTE OXALIC ACID TO DISSOLVEHIGH LEVEL WASTE IRON BASED SLUDGE SIMULANT

At the Savannah River Site (SRS), near Aiken South Carolina, there is a crucial need to remove residual quantities of highly radioactive iron-based sludge from large select underground storage tanks (e.g., 19,000 liters of sludge per tank), in order to support tank closure. The use of oxalic acid is planned to dissolve the residual sludge, hence, helping in the removal. Based on rigorous testing, primarily using 4 and 8 wt% oxalic acid solutions, it was concluded that the more concentrated the acid, the greater the amount of residual sludge that would be dissolved; hence, a baseline technology on using 8 wt% oxalic acid was developed. In stark contrast to the baseline technology, reports from other industries suggest that the dissolution will most effectively occur at 1 wt% oxalic acid (i.e., maintaining the pH near 2). The driver for using less oxalic acid is that less (i.e., moles) would decrease the severity of the downstream impacts (i.e., required oxalate solids removal efforts). To determine the initial feasibility of using 1 wt% acid to dissolve > 90% of the sludge solids, about 19,000 liters of representative sludge was modeled using about 530,000 liters of 0 to 8 wt% oxalic acid solutions. With the chemical thermodynamic equilibrium based software results showing that 1 wt% oxalic acid could theoretically work, simulant dissolution testing was initiated. For the dissolution testing, existing simulant was obtained, and an approximate 20 liter test rig was built. Multiple batch dissolutions of both wet and air-dried simulant were performed. Overall, the testing showed that dilute oxalic acid dissolved a greater fraction of the stimulant and resulted in a significantly larger acid effectiveness (i.e., grams of sludge dissolved/mole of acid) than the baseline technology. With the potential effectiveness confirmed via simulant testing, additional testing, including radioactive sludge testing, is planned.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Cesium Removal Performance Comparisons of Crystalline Silicotitanate Media Batches with Savannah River Site Waste Simulant

The Tank Closure Cesium Removal (TCCR) system uses ion exchange columns filled with Crystalline Silicotitanate (CST) media to process radioactive waste solutions for the removal of Cs137. TCCR currently focuses on dissolving Savannah River Site (SRS) Tank 10H waste (primarily sodium salt cake solids) within the tank followed by at-tank ion exchange column treatment. Plans are underway to prepare and install a second TCCR unit at SRS. Capacity and particle size differences exist between archived (IE-911) and more recently-prepared CST media batches (9120- B and 9140-B). Side-by-side comparison testing was performed to evaluate the cesium removal performance of each batch to aid in selecting the preferred CST batch and media characteristics to load into the second TCCR unit. Batch contact equilibrium and flow-through column tests have been conducted with three CST batches using an SRS Average Simulant. Simulant batch contact equilibrium cesium loading results for the three CST batches (including two lots of one batch) are provided in Table ES-1. The 35 °C data indicates that the archived IE-911 batch has a higher cesium capacity than recently-prepared CST media and that the minor TCCR CST 9120-B media lot (2099000035) has similar cesium removal performance to the major TCCR lot (2099000034). Tests conducted at 25 ºC for the archived IE-911 CST batch indicated lower cesium removal performance with this simulant batch than was observed recently with a different SRS Average Simulant batch. A dilution factor (DF) is typically utilized when modeling engineered CST media cesium loading performance to account for mass contributions from the binder material. In cases where CST performance is lower than expected, this factor includes corrections for the binder and for low performance. The ZAM (Zheng, Anthony, and Miller) Isotherm Model DF values are provided in Table ES-1 for each simulant batch contact result. DF values near 0.5 were determined for the 9120-B and 9140-B CST batch contact tests while DF values near 0.6 (20% higher) were determined for the tests with IE-911. These dilution factors are lower than recently observed with a different SRS Average Simulant batch (9140-B DF = 0.68; IE-911 DF = 1.0). Based on these results, it appears that some component in the simulant solution used for equilibrium testing may have resulted in reduced cesium loading on the CST media.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Electrochemical reduction of ammonia-captured CO 2 to CO over a nickel single-atom catalyst

Carbon reactive capture and conversion offers a sustainable route to valuable chemicals and fuels while aiding Green House Gas (GHG) reduction. Direct electrochemical conversion of capture solutions like bicarbonate avoids the energy demands of conventional CO 2 regeneration. Ammonium bicarbonate (NH 4 HCO 3 ) is particularly attractive due to its low decomposition temperature and ability to supply in situ CO 2 from dilute sources without requiring purified CO 2 . Meanwhile, single-atom catalysts (SACs) with nitrogen-coordinated metal sites further enhance CO 2 reduction efficiency using Earth-abundant materials. In this study, we demonstrate a nickel single-atom catalyst (Ni-SAC)-based electrolyzer that utilizes NH 4 HCO 3 as the CO 2 source, achieving significantly improved CO production performance compared to the conventional silver cathodes used in the CO 2 reduction reaction (CO 2 RR) to produce CO. The Ni-SAC cathode exhibited a Faradaic efficiency of 60.1% for CO production at −200 mA cm −2 , while the silver cathode achieved a Faradaic efficiency of only 2%, likely due to ammonium-induced poisoning. Furthermore, the integration of a customized microporous layer onto the electrode significantly increased the Faradaic efficiency from 64% to 83% at −100 mA cm −2 , emphasizing the crucial role of electrode structure optimization in enhancing CO selectivity. These findings demonstrate a sustainable and economically viable strategy for green CO production directly from CO 2 capture solutions.

30 DIRECT ENERGY CONVERSION↗

Low-temperature thermodynamics of the unitary Fermi gas: Superfluid fraction, first sound, and second sound

We investigate the low-temperature thermodynamics of the unitary Fermi gas by introducing a model based on the zero-temperature spectra of both bosonic collective modes and fermonic single-particle excitations. We calculate the Helmholtz free energy and from it we obtain the entropy, the internal energy, and the chemical potential as a function of the temperature. By using these quantities and the Landau's expression for the superfluid density we determine analytically the superfluid fraction, the critical temperature, the first sound velocity, and the second sound velocity. We compare our analytical results with other theoretical predictions and experimental data of ultracold atoms and dilute neutron matter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Stainless and carbon steel corrosion in aqueous piperazine at absorber and water wash conditions

Corrosion of carbon steel (C1010) and stainless steels (304, 316L, 430) was measured at absorber and water wash conditions at the bench scale. Corrosion rate decreases with increasing concentration of piperazine (PZ). With more than 0.003 m PZ in solution, carbon steel has acceptable corrosion performance. Corrosion of carbon steel increases with increasing partial pressure of CO2, suggesting loading is another dominant parameter. The effect is more significant for dilute PZ; therefore, untreated flue gas with high CO2 content should be avoided in the water wash. Temperature has a less significant effect than PZ concentration and loading. Carbon steel corrosion increases with increasing flow velocity at both absorber and water wash conditions

Liu, Ching-Ting↗

Analyzing Solutions High in Total Dissolved Solids for Rare Earth Elements (REEs) Using Cation Exchange and Online Pre-Concentration with the seaFAST2 Unit; NETL-TRS-7-2017; NETL Technical Report Series; U.S. Department of Energy, National Energy Technology Laboratory: Albany, OR, 2017; p 32

The accurate quantification of the rare earth element (REE) dissolved concentrations in natural waters are often inhibited by their low abundances in relation to other dissolved constituents such as alkali, alkaline earth elements, and dissolved solids. The high abundance of these constituents can suppress the overall analytical signal as well as create isobaric interferences on the REEs during analysis. Waters associated with natural gas operations on black shale plays are characterized by high salinities and high total dissolved solids (TDS) contents >150,000 mg/L. Methods used to isolate and quantify dissolved REEs in seawater were adapted in order to develop the capability of analyzing REEs in waters that are high in TDS. First, a synthetic fluid based on geochemical modelling of natural brine formation fluids was created within the Marcellus black shale with a TDS loading of 153,000 mg/L. To this solution, 1,000 ng/mL of REE standards was added based on preliminary analyses of experimental fluids reacted at high pressure and temperature with Marcellus black shale. These synthetic fluids were then run at three different dilution levels of 10, 100, and 1,000–fold dilutions through cation exchange columns using AG50-X8 exchange resin from Eichrom Industries. The eluent from the cation columns were then sent through a seaFAST2 unit directly connected to an inductively coupled plasma mass spectrometer (ICP-MS) to analyze the REEs. Percent recoveries of the REEs ranged from 80–110% and fell within error for the external reference standard used and no signal suppression or isobaric interferences on the REEs were observed. These results demonstrate that a combined use of cation exchange columns and seaFAST2 instrumentation are effective in accurately quantifying the dissolved REEs in fluids that are >150,000 mg/L in TDS and have Ba:Eu ratios in excess of 380,000.

03 NATURAL GAS↗

Understanding the solidification and microstructure evolution during CSC-MIG welding of Fe–Cr–B-based alloy

The present is a study of the solidification and microstructure of Fe–28.2%Cr–3.8%B–1.5%Si–1.5%Mn (wt.%) alloy deposited onto a 1020 plain carbon steel substrate using the controlled short-circuit metal inert gas welding process. The as-solidified alloy was a metal matrix composite with a hypereutectic microstructure. Thermodynamic calculation based on the Scheil–Gulliver model showed that a primary (Cr,Fe){sub 2}B phase formed first during solidification, followed by an eutectic formation of the (Cr,Fe){sub 2}B phase and a body-centered cubic Fe-based solid solution matrix, which contained Cr, Mn and Si. Microstructure analysis confirmed the formation of these phases and showed that the shape of the (Cr,Fe){sub 2}B phase was irregular plate. As the welding heat input increased, the weld dilution increased and thus the volume fraction of the (Cr,Fe){sub 2}B plates decreased while other microstructural characteristics were similar. - Highlights: • We deposit Fe–Cr–B-based alloy onto plain carbon steel using the CSC-MIG process. • We model the solidification behavior using thermodynamic calculation. • As deposited alloy consists of (Cr,Fe){sub 2}B plates embedded in Fe-based matrix. • We study the effect of the welding heat input on the microstructure.

36 MATERIALS SCIENCE↗

Iron incorporation in synthetic precipitated calcium silicate hydrates

Effect of Fe{sup 3+} on the precipitation of synthetic calcium silicate hydrates (C-S-H) under controlled conditions has been evaluated. Using extremely basic either initial calcium nitrate or sodium silicate solutions (pH > 11), incipient formation of ferrihydrite in both solutions was observed. In this case both C-S-H and iron-containing siliceous hydrogarnet are formed. For pH < 11, ferrihydrite was absent. Only C-S-H is formed. The presence of magnetically dilute Fe{sup 3+} in the C-S-H was shown by EPR and the atomic Fe/Si ratio of the C-S-H phase was shown to be between 0.01% and 0.1% by measuring and modelling the {sup 29}Si spin-lattice relaxation in NMR experiments. A uniform distribution of Fe{sup 3+} when C-S-H precipitates in the absence of initial ferrihydrite is obtained. When initial ferrihydrite is present, a non-uniform distribution of Fe{sup 3+} is found and the concentration of Fe{sup 3+} in the C-S-H is merely 3% of the overall iron concentration, suggesting the initial formation of ferrihydrite restricts the incorporation of iron into C-S-H.

36 MATERIALS SCIENCE↗

Thermal diffusion segregation of an impurity in a driven granular fluid

We study segregation of an impurity in a driven granular fluid under two types of steady states. In the first state, the granular gas is driven by a stochastic volume force field with a Fourier-type profile while in the second state, the granular gas is sheared in such a way that inelastic cooling is balanced by viscous heating. We compare theoretical results derived from a solution of the (inelastic) Boltzmann equation at Navier-Stokes (NS) order with those obtained from the Direct Monte Carlo simulation (DSMC) method and molecular dynamics (MD) simulations. Good agreement is found between theory and simulation, which provides strong evidence of the reliability of NS granular hydrodynamics for these steady states (including the dynamics of the impurity), even at high inelasticity. In addition, preliminary results for thermal diffusion in granular fluids at moderate densities are also presented. As for dilute gases, excellent agreement is also found in this more general case.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Early stage structural development of prototypical zeolitic imidazolate framework (ZIF) in solution

Given the wide-ranging potential applications of metal organic frameworks (MOFs), an emerging imperative is to understand their formation with atomic scale precision. This will aid in designing syntheses for next-generation MOFs with enhanced properties and functionalities. Major challenges are to characterize the early-stage seeds, and the pathways to framework growth, which require synthesis coupled with in situ structural characterization sensitive to nanoscale structures in solution. Here we report measurements of an in situ synthesis of a prototypical MOF, ZIF-8, utilizing synchrotron X-ray atomic pair distribution function (PDF) analysis optimized for sensitivity to dilute species, complemented by mass spectrometry, electron microscopy, and density functional theory calculations. We observe that despite rapid formation of the crystalline product, a high concentration of Zn(2-MeIm) 4 (2-MeIm=2-methylimidazolate) initially forms and persists as stable clusters over long times. A secondary, amorphous phase also pervades during the synthesis, which has a structural similarity to the final ZIF-8 and may act as an intermediate to the final product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fixed points and flow analysis on off-equilibrium dynamics in the boson Boltzmann equation

We consider fixed points of steady solutions and flow directions using the boson Boltzmann equation that is a one-dimensionally reduced kinetic equation after the angular integration. With an elastic collision integral of the two-to-two scattering process, in the dense (dilute) regime where the distribution function is large (small), the boson Boltzmann equation has approximate fixed points with a power-law spectrum in addition to the thermal distribution function. We argue that the power-law fixed point can be exact in special cases. We elaborate a graphical presentation to display evolving flow directions similarly to the renormalization group flow, which explicitly exhibits how fixed points are connected and parameter space is separated by critical lines. We discuss that such a flow diagram contains useful information on thermalization processes out of equilibrium.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of a copper filler metal on the microstructure and mechanical properties of electron beam welded titanium-stainless steel joint

Cracking in an electron beam weld of titanium to stainless steel occurred during the cooling process because of internal thermal stress. Using a copper filler metal, a crack free joint was obtained, which had a tensile strength of 310 MPa. To determine the reasons for cracking in the Ti/Fe joint and the function of the copper filler metal on the improvement of the cracking resistance of the Ti/Cu/Fe joint, the microstructures of the joints were studied by optical microscopy, scanning electron microscopy and X-ray diffraction. The cracking susceptibilities of the joints were evaluated with microhardness tests on the cross-sections. In addition, microindentation tests were used to compare the brittleness of the intermetallics in the welds. The results showed that the Ti/Fe joint was characterized by continuously distributed brittle intermetallics such as TiFe and TiFe(Cr){sub 2} with high hardness ({approx} 1200 HV). For the Ti/Cu/Fe joint, most of the weld consisted of a soft solid solution of copper with dispersed TiFe intermetallics. The transition region between the weld and the titanium alloy was made up of a relatively soft Ti-Cu intermetallic layer with a lower hardness ({approx} 500 HV). The formation of soft phases reduced the cracking susceptibility of the joint. - Highlights: Black-Right-Pointing-Pointer Electron beam welded Ti/Fe joint cracked for the brittleness and residual stress. Black-Right-Pointing-Pointer Electron beam welded Ti/Cu/Fe joint with tensile strength of 310 MPa was obtained. Black-Right-Pointing-Pointer Cu diluted Ti and Fe contents in weld and separated the TiFe{sub 2} into individual blocks. Black-Right-Pointing-Pointer Interfacial hard Ti-Fe compounds were replaced by soft Ti-Cu compounds in the weld. Black-Right-Pointing-Pointer A large amount of solid solution of copper formed in the weld.

36 MATERIALS SCIENCE↗

In-Use Interfacial Stability of Monoclonal Antibody Formulations Diluted in Saline i.v. Bags

The use of monoclonal antibodies (mAbs) for the treatment of a variety of diseases is rapidly growing each year. Many mAbs are administered intravenously using i.v. bags containing 0.9% NaCl (normal saline). We studied the aggregation propensity of these antibody solutions in saline and compared it with a low ionic strength formulation buffer. Furthermore, the mAb studied in this work is prone to aggregate, and is known to form a viscoelastic network at the air-solution interface. We observed that this interfacial elasticity increased when formulated in saline. In the bulk, the mAbs exhibited a tendency to self-associate that was higher in saline. We also studied the aggregation of the mAbs in the presence of polysorbate-20, typically added to formulations to mitigate interfacial aggregation. We observed that with surfactants, the presence of salt in the buffer led to a greater mAb adsorption at the interface and resulted in the formation of more particulate aggregates. Our results show that the addition of salt to the buffer led to differences in the interfacial aggregation in mAb formulations, showing that stress studies used to screen for mAb aggregation intended for i.v. administration should be performed in conditions representative of their intended route of administration.

60 APPLIED LIFE SCIENCES↗

Investigating sluggish diffusion in a concentrated solid solution alloy using ion irradiation with in situ TEM

Concentrated solid solution alloys (CSAs) – including high entropy alloys – are known for their remarkable mechanical and corrosion resistances with superior tolerance against the deleterious effect of irradiation exposure when compared with pure metals and dilute alloys. To date, however, the mechanisms responsible for such improvements are still unclear and remain a subject of investigation. The present work reports in situ Transmission Electron Microscopy (TEM) study under simultaneous ion irradiation of the face-centred cubic (FCC) FeCrMnNi quaternary CSA, comparing with a non-equiatomic Fe-based alloy, the AISI-348 austenitic stainless steel that has Cr, Ni and Mn as alloying elements. The alloys were irradiated under the same conditions, with 6 keV He + and 134 keV Xe + ions at 298 K up to 1.7 x 10 17 ions&middot;cm -2 (4 displacements-per-atom or dpa) and 2.7 x 10 15 ions&middot;cm -2 (4 dpa), respectively. The nucleation of inert gas bubbles was tracked upon post-irradiation extended annealing up to 673 K. He and Xe bubbles were observed to grow at a rate slightly slower in the CSA. Trends from the bubble size analyses show that the nucleation and growth of inert gas bubbles may be suppressed or delayed in some conditions in the CSA.

36 MATERIALS SCIENCE↗

On the microscopic fluctuations driving the NMR relaxation of quadrupolar ions in water

Nuclear Magnetic Resonance (NMR) relaxation is sensitive to the local structure and dynamics around the probed nuclei. The Electric Field Gradient (EFG) is the key microscopic quantity to understand the NMR relaxation of quadrupolar ions, such as {sup 7}Li{sup +}, {sup 23}Na{sup +}, {sup 25}Mg{sup 2+}, {sup 35}Cl{sup −}, {sup 39}K{sup +}, or {sup 133}Cs{sup +}. Using molecular dynamics simulations, we investigate the statistical and dynamical properties of the EFG experienced by alkaline, alkaline Earth, and chloride ions at infinite dilution in water. Specifically, we analyze the effect of the ionic charge and size on the distribution of the EFG tensor and on the multi-step decay of its auto-correlation function. The main contribution to the NMR relaxation time arises from the slowest mode, with a characteristic time on the picosecond time scale. The first solvation shell of the ion plays a dominant role in the fluctuations of the EFG, all the more that the ion radius is small and its charge is large. We propose an analysis based on a simplified charge distribution around the ion, which demonstrates that the auto-correlation of the EFG, hence the NMR relaxation time, reflects primarily the collective translational motion of water molecules in the first solvation shell of the cations. Our findings provide a microscopic route to the quantitative interpretation of NMR relaxation measurements and open the way to the design of improved analytical theories for NMR relaxation for small ionic solutes, which should focus on water density fluctuations around the ion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Review Of Cleaning Solutions For Use On Components Of The 9975 Shipping Package

Several candidate cleaning products have been reviewed for use as a disinfectant on 9975 shipping package components which contain or have contacted mold. Following review of the compatibility of these products with each component, ammonia (ammonium hydroxide diluted to 1.5 wt% concentration) appears compatible with all package components that it might contact. Each of the other candidate products is incompatible with one or more package components. Accordingly, ammonia is recommended for this purpose. It is further recommended that all components which are disinfected be subsequently rinsed with di-ionized or distilled water.

42 ENGINEERING↗