Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Summary of Airfoil Data

Recent airfoil data for both flight and wind-tunnel tests have been collected and correlated insofar as possible. The flight data consist largely of drag measurements made by the wake-survey method. Most of the data on airfoil section characteristics were obtained in the Langley two-dimensional low-turbulence pressure tunnel. Detail data necessary for the application of NACA 6-serles airfoils to wing design are presented in supplementary figures, together with recent data for the NACA 24-, 44-, and 230-series airfoils. The general methods used to derive the basic thickness forms for NACA 6- and 7-series airfoils and their corresponding pressure distributions are presented. Data and methods are given for rapidly obtaining the approximate pressure distributions for NACA four-digit, five-digit, 6-, and 7-series airfoils. The report includes an analysis of the lift, drag, pitching-moment, and critical-speed characteristics of the airfoils, together with a discussion of the effects of surface conditions. Available data on high-lift devices are presented. Problems associated with lateral-control devices, leading-edge air intakes, and interference are briefly discussed. The data indicate that the effects of surface condition on the lift and drag characteristics are at least as large as the effects of the airfoil shape and must be considered in airfoil selection and the prediction of wing characteristics. Airfoils permitting extensive laminar flow, such as the NACA 6-series airfoils, have much lower drag coefficients at high speed and cruising lift coefficients than earlier types-of airfoils if, and only if, the wing surfaces are sufficiently smooth and fair. The NACA 6-series airfoils also have favorable critical-speed characteristics and do not appear to present unusual problems associated with the application of high-lift and lateral-control devices. Much of the data given in the NACA Advance Confidential Report entitled "Preliminary Low-Drag-Airfoil and Flap Data from Tests at Large Reynolds Number and Low Turbulence," by Eastman N. Jacobs, Ira R. Abbott, and Milton Davidson, March 1942 has been corrected and included in the present paper, which supersedes the previously published paper.

LOW-DRAG↗

Computations of Viking Lander Capsule Hypersonic Aerodynamics with Comparisons to Ground and Flight Data

Comparisons are made between the LAURA Navier-Stokes code and Viking Lander Capsule hypersonic aerodynamics data from ground and flight measurements. Wind tunnel data are available for a 3.48 percent scale model at Mach 6 and a 2.75 percent scale model at Mach 10.35, both under perfect gas air conditions. Viking Lander 1 aerodynamics flight data also exist from on-board instrumentation for velocities between 2900 and 4400 m/sec (Mach 14 to 23.3). LAURA flowfield solutions are obtained for the geometry as tested or flown, including sting effects at tunnel conditions and finite-rate chemistry effects in flight. Using the flight vehicle center-of-gravity location (trim angle approx. equals -11.1 deg), the computed trim angle at tunnel conditions is within 0.31 degrees of the angle derived from Mach 6 data and 0.13 degrees from the Mach 10.35 trim angle. LAURA Mach 6 trim lift and drag force coefficients are within 2 percent of measured data, and computed trim lift-to-drag ratio is within 4 percent of the data. Computed trim lift and drag force coefficients at Mach 10.35 are within 5 percent and 3 percent, respectively, of wind tunnel data. Computed trim lift-to-drag ratio is within 2 percent of the Mach 10.35 data. Using the nominal density profile and center-of-gravity location, LAURA trim angle at flight conditions is within 0.5 degrees of the total angle measured from on-board instrumentation. LAURA trim lift and drag force coefficients at flight conditions are within 7 and 5 percent, respectively, of the flight data. Computed trim lift-to-drag ratio is within 4 percent of the data. Computed aerodynamics sensitivities to center-of-gravity location, atmospheric density, and grid refinement are generally small. The results will enable a better estimate of aerodynamics uncertainties for future Mars entry vehicles where non-zero angle-of-attack is required.

Edquist, Karl T.↗

Application of an Unstructured Grid Navier-Stokes Solver to a Generic Helicopter Boby: Comparison of Unstructured Grid Results with Structured Grid Results and Experimental Results

An unstructured-grid Navier-Stokes solver was used to predict the surface pressure distribution, the off-body flow field, the surface flow pattern, and integrated lift and drag coefficients on the ROBIN configuration (a generic helicopter) without a rotor at four angles of attack. The results are compared to those predicted by two structured- grid Navier-Stokes solvers and to experimental surface pressure distributions. The surface pressure distributions from the unstructured-grid Navier-Stokes solver are in good agreement with the results from the structured-grid Navier-Stokes solvers. Agreement with the experimental pressure coefficients is good over the forward portion of the body. However, agreement is poor on the lower portion of the mid-section of the body. Comparison of the predicted surface flow patterns showed similar regions of separated flow. Predicted lift and drag coefficients were in fair agreement with each other.

Mineck, Raymond E.↗

Wind Tunnel Testing of Active Flow Control on High-Lift Common Research Model

A 10%-scale high-lift version of the Common Research Model (CRM-HL) and an Active Flow Control (AFC) version of the model equipped with a simple-hinged flap (CRM-SHLAFC) were successfully tested. The tests were performed in the 14- by 22-Foot Subsonic Tunnel (14x22) at the NASA Langley Research Center (LaRC). The CRM-HL has a set of 37° inboard and outboard single-element Fowler flaps. The CRM-SHL-AFC has a set of 50° inboard and 55° outboard simple-hinged flaps equipped with integrated modular AFC cartridges on the flap shoulder. Both high-lift configurations share the same 30° slats and engine nacelle. Three new types of AFC devices were examined: the Double-Row Sweeping Jets (DRSWJ), the Alternating Pulsed Jets (APJ), and the High Efficiency Low Power (HELP) actuators. The DRSWJ and the APJ actuators used two rows of unsteady jets, whereas the HELP actuators used a combination of unsteady and steady jets, to overcome strong adverse pressure gradients while minimizing the mass flow usage. Nozzle pressure ratio, mass flow consumption and the power coefficient, which takes account of both supply air pressure and mass flow usage for the actuators, were used for judging the performance efficiency of the AFC devices. A prestall lift performance degradation for the CRM-HL configuration was resolved with a properly placed nacelle chine. The configuration with nacelle chine was chosen as the representative reference conventional high-lift case for comparison with the CRMSHL- AFC. The AFC-induced lift coefficient increment (DCL) was maintained for the entire lift curve over the CRM-SHL-AFC case with no AFC for almost all flow-control cases examined. The lift curve of the reference CRM-HL have a slightly steeper slope compared to those of the CRM-SHL-AFC configurations. The HELP actuation concept was extremely effective in controlling flow separation in the “linear region” of the curves comparing lift coefficient to mass flow rate. The HELP actuation achieved a targeted DCL of 0.50 using a moderate amount of mass flow and supply air pressure. The CRM-SHL-AFC configuration equipped with HELP actuation was able to match or exceed the lift performance of the reference conventional high-lift configuration (i.e., CRM-HL equipped with a nacelle chine), thus meeting the NASA Advanced Air Transport Technology (AATT) project goal.

Lin, John C.↗

Effect of Slot-Entry Skirt Extensions on Aerodynamic Characteristics of a Wing Section of the XB-36 Airplane Equipped with a Double Slotted Flap

An investigation was made in the Langley two-dimensional low-turbulence tunnel on a wing section for the XB-36 airplane equipped with a double slotted flap to determine the effect on lift and drag of various slot-entry skirt extension. A skirt extension of 0.787 deg. was found to provide the best combination of high maximum lift with flap deflected and law drag with flap retracted. The data showed that the maximum lift at intermediate (20 deg. to 45 deg.) flap deflections was lowered considerably by the slot-entry extension; but at high flap deflections the effect was small. An increase in Reynolds number from 2.4 million to 6.0 million increased the maximum.lift coefficient at a flap deflection of 55 deg. from 3.12 to 3.30 and from 1.18 to 1.40 for the flap retracted condition, but did not greatly affect the maximum lift coefficient for intermediate flap deflections. The flap and fore flap load data indicated that the maximum lift coefficients at high flap deflections are limited by a breakdown in the flow over the .flaps.

Cahill, Jones F.↗

Wind-tunnel investigation of aerodynamic efficiency of three planar elliptical wings with curvature of quarter-chord line

Three planar, untwisted wings with the same elliptical chord distribution but with different curvatures of the quarter-chord line were tested in the Langley 8-Foot Transonic Pressure Tunnel (8-ft TPT) and the Langley 7- by 10-Foot High-Speed Tunnel (7 x 10 HST). A fourth wing with a rectangular planform and the same projected area and span was also tested. Force and moment measurements from the 8-ft TPT tests are presented for Mach numbers from 0.3 to 0.5 and angles of attack from -4 degrees to 7 degrees. Sketches of the oil-flow patterns on the upper surfaces of the wings and some force and moment measurements from the 7 x 10 HST tests are presented at a Mach number of 0.5. Increasing the curvature of the quarter-chord line makes the angle of zero lift more negative but has little effect on the drag coefficient at zero lift. The changes in lift-curve slope and in the Oswald efficiency factor with the change in curvature of the quarter-chord line (wingtip location) indicate that the elliptical wing with the unswept quarter-chord line has the lowest lifting efficiency and the elliptical wing with the unswept trailing edge has the highest lifting efficiency; the crescent-shaped planform wing has an efficiency in between.

Mineck, Raymond E.↗

Water Energy Resource Innovation on the Cavitation Characteristics

The main purpose of this study is to numerically correlate the amount of generated vapor over a hydrofoil to the lift and drag coefficients acting on it. As such, cavitation characteristics were investigated of a hydrofoil in the cavitating, sub-cavitating, and non-cavitating flows for different angles of attacks (AoA) with the high upstream flow velocity. The hydrofoil was tested in a square water tunnel with water entering the tunnel at various velocities for each AoA ranges from 9.1 m/s to 12.2 m/s. It was found that lift and drag forces acting on the hydrofoil follow the trend of the experimental data quite closely. While the cavitation can be identified by a unique number (averaged vapor volume fraction), the work done created an inverse correlation between this number and the cavitation number at the same angle of attack. The lift force declines with the increase in the vapor content on the hydrofoil surface, meanwhile the drag force peaks at certain vapor volume fraction, and then, a huge reduction occurs with the considerable decrease in the corresponding cavitation number. A fourth-order correlation generated between the lift to drag (L/D) and the cavitation number (σ). It was found the lift-to-drag ratio decreases by the formation of the cavitation over the hydrofoil, thus causing a drop in the efficiency of the turbomachines.

42 ENGINEERING↗

Full-scale Wind-tunnel and Flight Tests of a Fairchild 22 Airplane Equipped with External-airfoil Flaps

Wind-tunnel and flight tests have been made of a Fairchild 22 airplane equipped with a wing having external-airfoil flaps that also perform the function of ailerons. Lift, drag, and pitching-moment coefficients of the airplane with several flap settings, and the rolling- and yawing-moment coefficients with the flaps deflected as ailerons were measured in the full-scale tunnel with the horizontal tail surfaces and propeller removed. The effect of the flaps on the low speed and on the take-off and landing characteristics, the effectiveness of flaps when used as ailerons, and the forces required to operate them as ailerons were determined in flight. The wind-tunnel tests showed that the flaps increased the maximum lift coefficient of the airplane from 1.51 with the flap in the minimum drag position to 2.12 with the flap in the minimum drag position to 2.12 with the flap deflected 30 degrees. In the flight tests the minimum speed decreased from 46.8 miles per hour with the flaps up to 41.3 miles per hour with the flaps deflected. The required take-off run to attain a height of 50 feet was reduced from 820 to 750 feet and the landing run from a height of 50 feet was reduced from 930 to 480 feet. The flaps for this installation gave lateral control that was not entirely satisfactory. Their rolling action was good but the adverse yaw resulting from their use was greater than is considerable, and the stick forces required to operate them increased too rapidly with speed.

Reed, Warren D↗

Wind tunnel tests of an NACA 23021 airfoil equipped with a slotted extensible and a plain extensible flap

An investigation has been made in the NACA 7- by 10-foot wind tunnel of a large chord NACA 23021 airfoil equipped with two arrangements of a completely extended 15 percent chord extensible flap. One of the flaps had a faired juncture, without a gap; the other was provided with a slot between the trailing edge of the airfoil and the nose of the flap. The results showed that the basic airfoil gave the lowest profile-drag coefficients over the low lift range, the airfoil with the plain extensible flap gave the lowest profile-drag coefficients over the moderate lift range, and the airfoil with the slotted extensible flap gave the lowest profile-drag coefficients over the high lift range. The airfoil with the slotted extensible flap had the same maximum lift at a flap deflection of 25 degrees as the airfoil with the plain extensible flap had at a flap deflection of 60 degrees. The results of comparisons of the airfoil pitching-moment coefficients obtained with the two types of flap are dependent upon the basis chosen for comparison. Complete aerodynamic section characteristics are presented for the various flap deflections for both flap arrangements in the completely extended portion.

Swanson, Robert S↗

Detailed measurements of the flowfield in the vicinity of an airfoil with glaze ice

An experimental study has been conducted in the OSU subsonic tunnel to measure the characteristics of the separation bubble on an airfoil with glaze ice. A measured glaze ice accretion on a NACA 0012 airfoil was simulated in wood for this dry tunnel test. The 21 inch chord model was pressure belted and the ice shape internally tapped to obtain surface pressures, lift and moment coefficients. A wake survey probe was used to obtain airfoil drag. The separation bubble was explored by measuring the time averaged velocities using a split film probe. The probe was positioned using a computer controlled two-dimensional traversing system. In this paper, airfoil lift, drag, and moment coefficient data are compared for the airfoil with and without glaze ice. Velocity profiles in the separation bubble are presented for several chordwise stations at three angles of attack. The ice shape caused a severe lift and drag penalty. The velocity profiles show clearly the large bubble geometry, regions of reversed flow, and bubble reattachment.

Bragg, M. B.↗

Note on two formulations of Crank-Nicolson method for Navier-Stokes equations

Here, we consider two formulations of the Crank-Nicolson (CN) method for the Navier-Stokes equations (NSE). The “natural” way of implementing CN for NSE is formally second order accurate in time for both velocity and pressure, whereas another formulation approximates pressure with only first order accuracy in time. Both versions of the method are applied to the benchmark problem of computing drag and lift in the flow around a cylinder. We show that the presumably more accurate version of the CN can create a solution with nonphysical oscillations and give incorrect predictions for the maximal drag coefficient, whereas the other formulation of the method predicts the drag and lift coefficients more accurately and does not introduce nonphysical oscillations. We locate the source of the issue and suggest several remedies.

Crank-Nicolson↗

Exploratory Wind-Tunnel Investigation to Determine the Lift Effects of Blowing over Flaps from Nacelles Mounted Above the Wing

An exploratory wind-tunnel investigation has been made to determine the lift effects of blowing from nacelles over the upper surface of flaps on a model having a delta wing of aspect ratio 3. Several flap conditions were examined. High-pressure air was blown from an external-pipe arrangement supported above the wing to simulate jet-engine exhaust. The jet momentum- coefficient range was from 0 to 3.0 and the model angle of attack was 0 deg. The results of this limited investigation show that values of jet circulation lift coefficient larger than the Jet reaction were produced with blowing over flaps from nacelles mounted above the wing. 'I!heuse of double slotted flaps with the gap unsealed between the flaps and wing had a large detrimental effect on the lift capabilities. With these gaps sealed, larger lift coefficients were obtained when fantails were added to the nacelles. The longitudinal trim problems created by large diving moments were similar to those encountered with other jet-augmented-flap systems

Riebe, John M↗

Calculation of static longitudinal aerodynamic characteristics of STOL aircraft with upper surface blown flaps

An existing prediction method developed for EBF aircraft configurations was applied to USB configurations to determine its potential utility in predicting USB aerodynamic characteristics. An existing wing-flap vortex-lattice computer program was modified to handle multiple spanwise flap segments at different flap angles. A potential flow turbofan wake model developed for circular cross-section jets was used to model a rectangular cross-section jet wake by placing a number of circular jets side by side. The calculation procedure was evaluated by comparison of measured and predicted aerodynamic characteristics on a variety of USB configurations. The method is limited to the case where the flow and geometry of the configuration are symmetric about a vertical plane containing the wing root chord. Comparison of predicted and measured lift and pitching moment coefficients were made on swept wings with one and two engines per wing panel, various flap deflection angles, and a range of thrust coefficients. The results indicate satisfactory prediction of lift for flap deflections up to 55 and thrust coefficients less than 2. The applicability of the prediction procedure to USB configurations is evaluated, and specific recommendations for improvements are discussed.

Mendenhall, M. R.↗

A comparison of turbulence models in computing multi-element airfoil flows

Four different turbulence models are used to compute the flow over a three-element airfoil configuration. These models are the one-equation Baldwin-Barth model, the one-equation Spalart-Allmaras model, a two-equation k-omega model, and a new one-equation Durbin-Mansour model. The flow is computed using the INS2D two-dimensional incompressible Navier-Stokes solver. An overset Chimera grid approach is utilized. Grid resolution tests are presented, and manual solution-adaptation of the grid was performed. The performance of each of the models is evaluated for test cases involving different angles-of-attack, Reynolds numbers, and flap riggings. The resulting surface pressure coefficients, skin friction, velocity profiles, and lift, drag, and moment coefficients are compared with experimental data. The models produce very similar results in most cases. Excellent agreement between computational and experimental surface pressures was observed, but only moderately good agreement was seen in the velocity profile data. In general, the difference between the predictions of the different models was less than the difference between the computational and experimental data.

Rogers, Stuart E.↗

Aerodynamics of 3-dimensional bodies in transitional flow

Based on considerations of fluid dynamic simulation appropriate to hypersonic, viscous flow over blunt-nosed lifting bodies, a method was presented earlier for estimating drag coefficients in the transitional-flow regime. The extension of the same method to prediction of lift coefficients is presented. Correlation of available experimental data by a simulation parameter appropriate for this purpose is the basis for the procedure described. The ease of application of the method makes it useful for preliminary studies which involve a wide variety of three-dimensional vehicle configurations or a range of angles of attack of a given vehicle.

Potter, J. Leith↗

Procedure for estimating aerodynamics of three-dimensional bodies in transitional flow

Based on considerations of fluid dynamic simulation appropriate to hypersonic, viscous flow over blunt-nosed lifting bodies, a method was presented earlier for estimating drag coefficients in the transitional-flow regime. The extension of the same method to prediction of lift coefficients is presented in this paper. Correlation of available experimental data by a simulation parameter appropriate for this purpose is the basis of the procedure described. Under low-density, hypersonic flow conditions, the overriding importance of projected and wetted areas, rather than details of body configuration, support this approach for finding aerodynamic forces. The ease of application of the method makes it useful for preliminary studies that involve a wide variety of three-dimensional vehicle configurations or a range of angles of attack of a given vehicle. It is also easy to examine the influence of different assumptions regarding gas/surface interaction parameters.

Potter, J. Leith↗

Airfoil Table Generation and Validation for the VR-12 and SSC-A09 Airfoils and Quadrotor Performance Prediction

As part of NASA’s Urban Air Mobility (UAM) mission, the Revolutionary Vertical Lift Technology (RVLT) project is creating rotorcraft reference designs that can be used by the rotorcraft community to develop quiet, efficient, and safer air vehicles. At NASA, this effort is made possible by the use of the RVLT toolchain software. Airfoil tables are often a critical part of the conceptual design process as they inform both comprehensive analysis and Computational Fluid Dynamics (CFD) codes of 2D aerodynamic coefficients, such as lift, drag, and moment coefficients. These airfoil tables, typically generated during experimental testing, are often proprietary and thus not widely distributable; further, there is not always clear or available reference documentation that provides information on the test conditions. The airfoil tables from these experiments are referred to in this work as Legacy airfoil tables. The scope of this study is to generate airfoil tables with the NASA OVERset grid CFD FLOW solver (OVERFLOW) coupled with the AirFoil Table Generator (AFTGen) software and validate these airfoil tables based on performance predictions calculated in Comprehensive Hierarchical Aeromechanics Rotorcraft Model (CHARM). The overall goal is to provide CFD generated airfoil tables, validate them through comprehensive analysis, and publish the airfoil tables for public distribution. The RVLT quadrotor reference model was selected as the basis for all analyses. The quadrotor uses the VR-12 and SSC-A09 airfoils for its rotor blades. Simulations were run in OVERFLOW for the VR-12 and SSC-A09 airfoils for ±20° angles of attack, Mach numbers from 0.3 to 1.0, and a Reynolds-Mach proportionality constant of 1.023x107. The C81 format airfoil tables from AFTGen were then blended with Legacy NACA 0012 airfoil table data for ±20° to ±180° angle of attack range. CHARM was used to compute thrust coefficient, power coefficient, and figure of merit for an isolated rotor in hover using proprietary legacy airfoil tables for the VR-12 and SSC-A09, as well as with the OVERFLOW generated airfoil tables for the VR-12 and SSC-A09. Overall, the OVERFLOW and Legacy performance predictions agreed well, with the best correlation between simulated and Legacy data observed with the VR-12 airfoil tables.

Airfoil↗

Compressible 2D Flow Field Interaction of Two Contra-Rotating Blades

The blades of coaxial, contra-rotating rotor systems cross each other in close proximity and at high relative speeds. This crossing event is a potential source of noise and severe blade loads. Effects of compressibility can aggravate the interaction and significantly alter the pressure field signature and phase relationships. A 2-D analysis of this phenomenon is performed by simulating two airfoils passing each other at specified speeds and vertical separation distances. Several test cases spanning a relevant range of Reynolds numbers, angles of attack, and relative Mach number are considered. The Mach number is varied to simulate the radial variation of velocity from the root to tip of a rotor blade to capture the pressure signature, lift, and drag of the airfoils. The velocity and pressure distributions on the airfoils, and in the space between the airfoils are computed before, at, and after airfoil crossing. The variations of lift and drag coefficients through the interaction are captured. The upper airfoil experiences an increase in lift followed by a very sharp drop in lift during the interaction. When relative Mach numbers are transonic, the region of interaction is greatly extended, with shock interactions occurring. The results show the complex nature of the aerodynamic and fluid dynamic impulses generated by blade-blade interactions, with implications to aeroelastic loads and aeroacoustic sources.

Barbely, Natasha L.↗