Search NASA⌕ Search

SEARCH · Search NASA

Results for “angle diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Quiet Clean Short-Haul Experimental Engine (QCSEE) aerodynamic characteristics of 30.5 centimeter diameter inlets

A low speed test program was conducted in a 9- by 15-foot V/STOL wind tunnel to investigate internal performance characteristics and determine key design features required for an inlet to meet the demanding operational conditions of the QCSEE application. Four models each having a design average throat Mach number of 0.79 were tested over a range of incidence angle, throat Mach number, and freestream velocity. Principal design variable was internal lip diameter ratio. Stable, efficient inlet performance was found to be feasible at and beyond the 50 deg incidence angle required by the QCSEE application at its 41.2 m/sec (80 knot) nominal takeoff velocity, through suitably designed inlet lip and diffuser components. Forebody design was found to significantly impact flow stability via nose curvature. Measured inlet wall pressures were used to select a location for the inlet throat Mach number control's static pressure port that properly balanced the conflicting demands of relative insensitivity to flow incidence and sufficiently high response to changes in engine flow demand.

Paul, D. L.↗

Effect of rotor meridional velocity ratio on response to inlet radial and circumferential distortion

Three single transonic fan stages, each having a different meridional velocity ratio across its rotor, were tested with two magnitudes of tip radial distortion and with a 90 deg circumferential distortion imposed on the inlet flow. The rotor with the lowest meridional velocity ratio (less than 0.9 at the tip) demonstrated the least degradation of performance due to these distortions. Loss and deviation angle data (as needed for performance prediction with radial distortion) calculated along actual streamlines for radially distorted flow and correlated against diffusion factor, showed consistent agreement with data calculated along design streamlines for undistorted flow.

Sanger, N. L.↗

Hover performance validation of an ejector configured STOVL fighter aircraft

The hover thrust performance of a full-scale model of an ejector-lift/vectored thrust Short Take-Off and Vertical Landing (STOVL) fighter configuration was measured at the Outdoor Aerodynamic Research Facility of the National Full-Scale Aerodynamics Complex located at NASA Ames Research Center. The static thrust of the lifting ejector and ventral nozzle was calibrated at an out-of-ground-effect height. The test permitted comparison with static thrust calibrations obtained in the 80- by 120-Foot Wind Tunnel. The average static thrust augmentation ratio of the ejector system was 1.55 compared with the design goal of 1.63. The outdoor test showed that the addition of short extensions to the diffuser on the fuselage sidewall decreased suckdown and increased ejector performance. As expected, an increase in the ventral nozzle thrust deflection angle from nearly horizontal to the vertical-lift hover position caused a significant decrease in thrust. Flow visualization using smoke revealed greater secondary airflow into the left ejector and the penetration of hot ventral gases along the ground beneath and between the cool plumes from the ejector system.

Naumowicz, Tim↗

Two-dimensional compressible flow in centrifugal compressors with straight blades

Six numerical examples are presented for steady, two-dimensional, compressible, nonviscous flow in centrifugal compressors with thin straight blades, the center lines of which generate the surface of a right circular cone when rotated about the axis of the compressor. A seventh example is presented for incompressible flow. The solutions were obtained in a region of the compressors, including the impeller tip, that was considered to be unaffected by the diffuser vanes or by the impeller-inlet configuration. Each solution applies to radial and mixed flow compressors with various cone angles but with the same angle between blades on the conic flow surface. The solution also apply to radial and mixed flow turbines with the rotation and the flow direction reversed. The effects of variations in the following parameters were investigated: (1) flow rate, (2) impeller-tip speed, (3) variation of passage height with radius, and (4) angle between blades on conic flow surface. The numerical results are presented in plots of the streamlines and constant Mach number lines. Correlation equations are developed whereby the flow conditions in any impeller with straight blades can be determined (in the region investigated by this analysis) for all operating conditions.

Stanitz, John D↗

Cosmic Diffuse Analysis

The final analysis of the COMPTEL cosmic diffuse flux analysis is summarized in the accompanying figure. It shows the intensity of the cosmic diffuse flux spectrum measured jointly between the Virgo region and the South Galactic pole. This spectrum represents flux per unit solid angle over the range of 0.8 to 30 MeV. It contains the first positive measurement of the flux above 10 MeV. The spectrum merges smoothly with that measured with the EGRET instrument, starting at 30 MeV. It also merges smoothly with the latest results of the HEAO-1 measurements. However, the spectrum below is softer than the spectrum above the COMPTEL energy band. In the COMPTEL energy band there must exist a change in spectral shape as the source objects or processes change from the lower energy regime to the higher energy regime. The details of the analysis and the implications and meanings of the results are spelled out in the thesis of Dr. Cheenu Kappadath which is enclosed.

Ryan, James M.↗

Heliospheric influence on the anisotropy of TeV cosmic rays

This paper provides a theory of using Liouville's theorem to map the anisotropy of TeV cosmic rays seen at Earth using the particle distribution function in the local interstellar medium (LISM). The ultimate source of cosmic ray anisotropy is the energy, pitch angle, and spatial dependence of the cosmic ray distribution function in the LISM. Because young nearby cosmic ray sources can make a special contribution to the cosmic ray anisotropy, the anisotropy depends on the source age, distance and magnetic connection, and particle diffusion of these cosmic rays, all of which make the anisotropy sensitive to the particle energy. When mapped through the magnetic and electric field of a magnetohydrodynamic model heliosphere, the large-scale dipolar and bidirectional interstellar anisotropy patterns become distorted if they are seen from Earth, resulting in many small structures in the observations. Best fits to cosmic ray anisotropy measurements have allowed us to estimate the particle density gradient and pitch angle anisotropies in the LISM. It is found that the heliotail, hydrogen deflection plane, and the plane perpendicular to the LISM magnetic field play a special role in distorting cosmic ray anisotropy. These features can lead to an accurate determination of the LISM magnetic field direction and polarity. The effects of solar cycle variation, the Sun's coronal magnetic field, and turbulence in the LISM and heliospheric magnetic fields are minor but clearly visible at a level roughly equal to a fraction of the overall anisotropy amplitude. The heliospheric influence becomes stronger at lower energies. Below 1 TeV, the anisotropy is dominated by small-scale patterns produced by disturbances in the heliosphere.

79 ASTRONOMY AND ASTROPHYSICS↗

Dynamic heterogeneity and nanophase separation in rubber-toughened amine-cured highly cross-linked polymer networks

Solid state nuclear magnetic resonance (NMR) spectroscopy and small-to wide-angle X-ray scattering (SWAXS) methods were used to characterize the heterogeneous dynamics and polymer domain structure in rubber modified thermoset materials containing the diglycidyl ether of bisphenol A (DGEBA) epoxy resin and a mixture of Jeffamine reactive rubber and 4,4-diaminodicyclohexylmethane (PACM) amine curing agent. The polymer chain dynamics and morphologies as a function of the PACM/Jeffamine ratio were determined. Using dipolar-filtered NMR experiments, the resulting networks are shown to be composed of mobile and rigid regions that are separated on nanometer length scales, along with a dynamically immobilized interface region. Proton NMR spin diffusion experiments measured the dimensions of the mobile phase to range between 9 and 66 nm and varied with the relative PACM concentration. Solid state 13 C magic angle spinning NMR experiments show that the highly mobile phase is composed entirely of the dynamically flexible polyether chains of the Jeffamine rubber, the immobilized interface region is a mixture of DGEBA, PACM, and the Jeffamine rubber, with the PACM cross-linked to DGEBA predominantly residing in the rigid phase. The SWAXS results showed compositional nanophase separation spanning the 11–77 nm range. These measurements of the nanoscale compositional and dynamic heterogeneity provide molecular level insight into the very broad and controllable glass transition temperature distributions observed for these highly cross-linked polymer networks.

36 MATERIALS SCIENCE↗

Analytical and experimental studies of a short compact subsonic diffuser for a two-dimensional supersonic inlet

An experimental study of a two-dimensional supersonic inlet with a short compact subsonic diffuser, length to exit diameter (dl/d) ratio of 1.25, was conducted to investigate the impact of the short diffuser on inlet performance at low speeds and to assess the diffuser subsonic performance for a simulated diffuser flow corresponding to high-speed inlet conditions near the design flight Mach number of 2.2. For the low-speed testing, a drooped lip was employed to improve the inlet performance at a high angle of attack. For the simulated high-speed testing, air was blown through slots or discrete nozzles as an active boundary-layer control. The results from the low-speed performance test were compared with the results from a previous test program on the same inlet with a long subsonic diffuser (dl/d = 4.5). The comparison indicates that inlet recovery was not affected by the use of the short diffuser for either the baseline (no droop) or the drooped cowl lip configuration. However, the inlet baseline distortion for the short diffuser configuration was substantially higher than for the long diffuser. A comparison of the two configurations with a 70 deg drooped lip showed no significant difference in distortion. For the portion of the experimental program in which diffuser conditions for high-speed flight were simulated, diffuser-induced flow separation occurred. This separation was predicted from an analytical study that used the Hess potential flow panel method and the Herring two-dimensional boundary-layer analysis computer codes. The flow separated mainly on the diffuser ramp. Subsequent tests in which boundary-control systems were utilized showed that blowing with either slots or discrete nozzles could suppress the flow separation in the short subsonic diffuser, thereby substantially improving the diffuser performance.

Iek, Chanthy↗

Diffusion Synthetic Acceleration for High Order S{sub N} Transport on Meshes with Curved Surfaces

Thermal radiation transport is integral to multiphysics applications such as inertial confinement fusion and astrophysics. Materials in these problems can be exceptionally optically thick and diffusive. A transport solver must be capable of accurate and efficient solutions to such problems. Previously, Woods et al. established a proof-of-concept for high order (HO) discontinuous Galerkin finite element (DGFEM) transport on meshes with curved surfaces. They numerically demonstrated the spatial convergence is order p + 1. Remarkably, these convergence rates are relatively invariant to the amount of curvature of the spatial mesh. We present here an extension of this work that demonstrates a rapidly-convergent iterative solver for the FEM transport equations on meshes with curved sides. We use the modified interior penalty (MIP) diffusion synthetic acceleration (DSA) established by Wang and Ragusa. The partially consistent MIP equations stem from the symmetric interior penalty (IP) derivation of the diffusion equation. The IP method is not stable for optically thick cells so it was combined with the diffusion conforming form (DCF), a discretized diffusion equation derived from the discretized S N equations that is not stable for intermediate optical thicknesses. The MIP equations adapt a 'switch' to the IP method in optically thinner regions and the DCF method in optically thicker regions. The literature does not reveal any Fourier analyses performed for iterative transport on meshes with curved surfaces. Wang and Ragusa performed a Fourier analysis for orthogonal meshes and our results appear to be as expected. Previous literature has reported on some of the sensitivities that affect the spectral radius of DSA schemes: polynomial order, and scattering ratios. Presently, we focus on the sensitivity of the spectral radius to polynomial order, scattering ratio, the constant C, and mesh curvature for varying cell thicknesses. We also numerically study the behavior of the spectral radius to verify our DSA implementation. A sequence of problems is designed to exercise the acceleration. As the problems become more optically thick and diffusive, the accelerated solution continues to converge toward the analytic solution. We employ the Modular Finite Element Methods (MFEM) package, developed at Lawrence Livermore National Laboratory, to generate the linear algebraic system of equations for each angle in the discrete ordinates quadrature set, and use UMFPack to solve this system of equations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Ionic liquid structure, dynamics, and electrosorption in carbon electrodes with bimodal pores and heterogeneous surfaces

In this paper, we investigate the aggregation, diffusion, and resulting electrochemical behavior of ionic liquids inside carbon electrodes with complex pore architectures and surface chemistries. Carbide-derived carbons (CDCs) with bimodal porosities and defunctionalized or oxidized electrode surfaces served as model electrode materials. Our goal was to obtain a fundamental understanding of room-temperature ionic liquid ion orientation, mobility, and electrosorption behavior. Neat 1-octyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide confined in CDCs was studied using an integrated experimental and modeling approach, consisting of quasielastic neutron scattering, small-angle neutron scattering, X-ray pair distribution function analysis, and electrochemical measurements, which were combined with molecular dynamics simulations. Our analysis shows that surface oxygen groups increase the diffusion of confined electrolytes. Consequently, the ions become more than twice as mobile in oxygen-rich pores. Although greater self-diffusion of ions translates into higher electrochemical mobilities in oxidized pores, bulk-like behavior of ions dominates in the larger mesopores and increases the overall capacitance in defunctionalized pores. Experimental results highlight strong confinement and surface effects of carbon electrodes on electrolyte behavior, and molecular dynamics simulations yield insight into diffusion and capacitance differences in specific pore regions. Finally, we demonstrate the significance of surface defects on electrosorption dynamics of complex electrolytes in hierarchical pore architectures of supercapacitor electrodes.

36 MATERIALS SCIENCE↗

Synthesis, structure, and optical properties of BiCuOCh (Ch=S, Se, and Te)

Crystals of BiCuOSe were grown from a salt flux, and the crystal structure was determined by single-crystal X-ray diffraction. BiCuOSe adopts the tetragonal layered structure of LnCuOCh (Ln=lanthanide; Ch=S, Se, and Te) with bond lengths and bond angles in good agreement with those published for powders. Powders comprising mixed chalcogenides across the series BiCuOCh (Ch=S, Se, and Te) were made by reacting Bi{sub 2}O{sub 2}Ch and Cu{sub 2}Ch. Band gaps determined via infrared diffuse reflectance from powders are E{sub g}=0.82 eV for BiCuOSe, 0.89 eV for BiCuOS{sub 0.5}Se{sub 0.5}, and 1.07 eV for BiCuOS. The band gap of BiCuOSe inferred from infrared transmission measurements on single crystals is in good agreement with the value obtained from diffuse reflectance from the powder. - Graphical abstract: IR absorption of BiCuOCh powders from diffuse reflection (left scale) and polished BiCuOSe single crystal from transmission (right scale). Spectra are normalized to the maximum absorption. Inset: band gap as a function of composition. Highlights: Black-Right-Pointing-Pointer BiCuOSe single crystals are synthesized, and the band gap is measured by direct transmission. Black-Right-Pointing-Pointer A new powder synthesis of BiCuOCh{sub 1-x}Ch Prime {sub x} is demonstrated. Black-Right-Pointing-Pointer Band gaps of BiCuO(S{sub 1-x}Se{sub x}) are determined from diffuse reflection from powders.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Global Mapping of Underwater UV Irradiances and DNA-Weighted Exposures using TOMS and SeaWiFS Data Products

The global stratospheric ozone-layer depletion results In an increase in biologically harmful ultraviolet (UV) radiation reaching the surface and penetrating to ecologically significant depths in natural waters. Such an increase can be estimated on a global scale by combining satellite estimates of UV irradiance at the ocean surface from the Total Ozone Mapping Spectrometer (TOMS) satellite instrument with the SeaWIFS satellite ocean-color measurements in the visible spectral region. In this paper we propose a model of seawater optical properties in the UV spectral region based on the Case I water model in the visible range. The inputs to the model are standard monthly SeaWiFS products: chlorophyll concentration and the diffuse attenuation coefficient at 490nm. Penetration of solar UV radiation to different depths in open ocean waters is calculated using the RT (radiative transfer) quasi-single scattering approximation (QSSA). The accuracy of the QSSA approximation in the water is tested using more accurate codes. The sensitivity study of the underwater UV irradiance to atmospheric and oceanic optical properties have shown that the main environmental parameters controlling the absolute levels of the UVB (280-320nm) and DNA-weighted irradiance underwater are: solar-zenith angle, cloud transmittance, water optical properties, and total ozone. Weekly maps of underwater UV irradiance and DNA-weighted exposure are calculated using monthly-mean SeaWiFS chlorophyll and diffuse attenuation coefficient products, daily SeaWiFS cloud fraction data, and the TOMS-derived surface UV irradiance daily maps. The final products include global maps of weekly-average UVB irradiance and DNA-weighted daily exposures at 3m and 10m, and depths where the UVB irradiance and DNA-weighted dose rate at local noon are equal to 10% of their surface values.

Vasilkov, Alexander↗

Narrow-angle cosmic-ray anisotropies

An alternate interpretation is presented for the diurnal cosmic ray anisotropy measurements made with underground muons in London. From the widely accepted models of cosmic ray diffusion in the Galaxy, a diurnal anisotropy (24 h wave) would be expected. But from a model predicting the occurrence of an excess within some small region of the celestial sphere, it is suggested that the direction of this excess would depend on the orientation (in space and time) of the source relative to galactic magnetic field lines which connect the source with the solar system.

Barrowes, S.↗

Calculation of the flow field in supersonic mixed-compression inlets at angle of attack using the three-dimensional method of characteristics with discrete shock wave fitting

The influence of molecular transport is included in the computation by treating viscous and thermal diffusion terms in the governing partial differential equations as correction terms in the method of characteristics scheme. The development of a production type computer program is reported which is capable of calculating the flow field in a variety of axisymmetric mixed-compression aircraft inlets. The results agreed well with those produced by the two-dimensional method characteristics when axisymmetric flow fields are computed. For three-dimensional flow fields, the results agree well with experimental data except in regions of high viscous interaction and boundary layer removal.

Vadyak, J.↗

Determination of Response Versus Scan Angle for the NOAA-20 Visible Infrared Imaging Radiometer Suite Thermal Emissive Bands from Emissive Radiation Measurements During the Pitch Maneuver

The visible infrared imaging radiometer suite (VIIRS) is a key sensor onboard the newly launched (November 18, 2017) NOAA-20 satellite and the early launched Suomi National Polar-orbiting Partnership (SNPP) satellite. The two VIIRS sensors are nearly identical in design. Its onboard calibration components include a solar diffuser (SD) and a SD stability monitor for the reflective solar bands, a V-grooved blackbody for the thermal emissive bands (TEBs),and a space view port for background subtraction. These onboard calibrators are located at fixed scan angles. The response versus scan angle (RVS) of the VIIRS scan mirror was characterized prelaunch in lab-ambient conditions and is currently used to calibrate the on-orbit response for all scan angles relative to the calibrator's scan angle. A spacecraft-level pitch maneuver was scheduled during the initial intensive calibration and validation testing for both the NOAA-20 and SNPP. The pitch maneuver provided a rare opportunity for VIIRS to make observations of deep space over the entire range of the scan angle, which can be used to characterize the TEBRVS. We analyze the NOAA-20 pitch maneuver data and assess the derived TEB RVS. A comparison between the RVS determined by the pitch maneuver observations and prelaunch lab measurements is conducted for each band, detector, and mirror side of the half-angle mirror.

Wu, Aisheng↗

Application of subgroup decomposition in diffusion theory to gas cooled thermal reactor problem

In this paper, the accuracy and computational efficiency of the subgroup decomposition (SGD) method in diffusion theory is assessed in a ID benchmark problem characteristic of gas cooled thermal systems. This method can be viewed as a significant improvement in accuracy of standard coarse-group calculations used for VHTR whole core analysis in which core environmental effect and energy angle coupling are pronounced. It is shown that a 2-group SGD calculation reproduces fine-group (47) results with 1.5 to 6 times faster computational speed depending on the stabilizing schemes while it is as efficient as single standard 6-group diffusion calculation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗