Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Post-landing major element quantification using SuperCam laser induced breakdown spectroscopy

The SuperCam instrument on the Perseverance Mars 2020 rover uses a pulsed 1064 nm laser to ablate targets at a distance and conduct laser induced breakdown spectroscopy (LIBS) by analyzing the light from the resulting plasma. SuperCam LIBS spectra are preprocessed to remove ambient light, noise, and the continuum signal present in LIBS observations. Prior to quantification, spectra are masked to remove noisier spectrometer regions and spectra are normalized to minimize signal fluctuations and effects of target distance. In some cases, the spectra are also standardized or binned prior to quantification. To determine quantitative elemental compositions of diverse geologic materials at Jezero crater, Mars, we use a suite of 1198 laboratory spectra of 334 well-characterized reference samples. The samples were selected to span a wide range of compositions and include typical silicate rocks, pure minerals (e.g., silicates, sulfates, carbonates, oxides), more unusual compositions (e.g., Mn ore and sodalite), and replicates of the sintered SuperCam calibration targets (SCCTs) onboard the rover. For each major element (SiO 2 , TiO 2 , Al 2 O 3 , FeO T , MgO, CaO, Na 2 O, K 2 O), the database was subdivided into five “folds” with similar distributions of the element of interest. One fold was held out as an independent test set, and the remaining four folds were used to optimize multivariate regression models relating the spectrum to the composition. We considered a variety of models, and selected several for further investigation for each element, based primarily on the root mean squared error of prediction (RMSEP) on the test set, when analyzed at 3 m. In cases with several models of comparable performance at 3 m, we incorporated the SCCT performance at different distances to choose the preferred model. Shortly after landing on Mars and collecting initial spectra of geologic targets, we selected one model per element. Subsequently, with additional data from geologic targets, some models were revised to ensure results that are more consistent with geochemical constraints. The calibration discussed here is a snapshot of an ongoing effort to deliver the most accurate chemical compositions with SuperCam LIBS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanoscale Growth Kinetics of Cu(In,Ga)Se 2 Absorbers

Here, we investigate the kinetics of elemental segregation during the synthesis of Cu(In 1–x ,Ga x )Se 2 (CIGS) thin films via a rapid thermal growth process. Changes in elemental concentration are mapped rapidly via in situ X-ray fluorescence (XRF) microscopy. In situ XRF enables the quantification of Cu, In, Ga, and Se concentrations with 200 nm spatial resolution over a region of 7 μm × 7 μm, large enough to map multiple CIGS grains. Reacting elemental precursor stacks at 500, 550, and 600 °C, we find that copper is the driving force for α-CIGS phase formation at a rate of 17 nmol/cm 2 /min at 500 °C. Because of the thermal expansion of the substrate, cluster analysis and classification algorithms were employed to track compositionally similar regions over time and across samples measured at different temperatures. Beyond the direct application of these results for the optimization of CIGS manufacturing, these in situ experiments demonstrate the feasibility of quantitative compositional evaluation at the nanoscale during the synthesis of technologically relevant materials. In combination with advanced analysis methods, this example shows how correlative X-ray microscopy can contribute to the solution of the materials paradigm, relating synthesis to composition and properties at the nanoscale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Adaptive Discovery and Mixed-Variable Optimization of Next Generation Synthesizable Microelectronic Materials

Design of new microelectronic materials is characterized by several challenges such as high-dimensionality of the atomic structure-composition variable space, formidable cost of directly using high-fidelity simulations for design optimization, dispersity in literature-reported similar materials and synthesis methods, complex physical mechanisms, and mixed qualitative and quantitative design variables that lead to a disjointed design space. Even though machine learning (ML) techniques have been employed to expedite materials innovation, existing methods treat ML and design optimization as two separate processes, failing to resolve the fundamental challenges associated with high dimensionality and mixed-variable complexity. We have developed a ML enhanced mixed-variable material design optimization framework to efficiently extract useful information from existing data in literature and physics-based simulations to guide the autonomous search for optimal materials. Our proposed framework is composed of four computational modules: (1) a natural language processing (NLP) based virtual screening module, (2) classification based concept exploration module, (3) a density functional theory (DFT)-based high-fidelity evaluation model, and (4) a novel latent-variable Gaussian process (LVGP) ML model for mixed-variable problems with uncertainty quantification, which seamlessly integrates with Bayesian Optimization (BO) and achieves superb efficiency through embedded physics-based dimension reduction. Our approach is demonstrated and validated using the testbed of functional materials exhibiting metal-insulation transitions (MITs), with the targeted reversible resistivity changes (∼10^5) near room temperature. At the end of the 30-month project, we have developed a series of new ML techniques using NLP, conditional variational autoencoders, active learning, latent-variable Gaussian processes, integrated with Bayesian optimization. Our project has resulted in new predicted MITs compounds and improved understanding of MITs microscopic mechanisms, which in turn will revolutionize microelectronics science to provide energy-saving solutions. Our research has improved both creativity and efficiency in transforming rare-event discoveries of new functional materials to persistent innovations. In addition to open-sourcing the online MIT database and the classification model, the LVGP open source code has been downloaded more than 15,000 times within two years. More than 40 MIT compounds have been identified and many have been pursued experimentally via collaborators. The research results are published in close to 20 collaborative papers in high-impact journals, such as Chem. Mater., Appl. Phys. Rev., Sci. Rep., among others of design space.

36 MATERIALS SCIENCE↗

Link between hopping models and percolation scaling laws for charge transport in mixtures of small molecules

Mixed host compositions that combine charge transport materials with luminescent dyes offer superior control over exciton formation and charge transport in organic light emitting devices (OLEDs). Two approaches are typically used to optimize the fraction of charge transport materials in a mixed host composition: either an empirical percolative model, or a hopping transport model. We show that these two commonly-employed models are linked by an analytic expression which relates the localization length to the percolation threshold and critical exponent. The relation is confirmed both numerically and experimentally through measurements of the relative conductivity of Tris(4-carbazoyl-9-ylphenyl) amine (TCTA) :1,3-bis(3,5-dipyrid-3-yl-phenyl) benzene (BmPyPb) mixtures with different concentrations, where the TCTA plays a role as hole conductor and the BmPyPb as hole insulator. Furthermore, the analytic relation may allow the rational design of mixed layers of small molecules for high-performance OLEDs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermodynamic Modeling and Optimization of the Copper Flash Converting Process Using the Equilibrium Constant Method

Based on the principle of multiphase equilibrium, a mathematical model of the copper flash converting process was established by the equilibrium constant method, and a computational system was developed with the use of MetCal software platform. The mathematical model was validated by comparing simulated outputs, industrial data, and published data. To obtain high-quality blister copper, a low copper content in slag, and increased impurity removal rate, the model was then applied to investigate the effects of the operational parameters [oxygen/feed ratio (R{sub OF}), flux rate (R{sub F}), and converting temperature (T)] on the product weights, compositions, and the distribution behaviors of impurity elements. The optimized results showed that R{sub OF}, R{sub F}, and T should be controlled at approximately 156 Nm{sup 3}/t, within 3.0 pct, and at approximately 1523 K (1250 °C), respectively.

36 MATERIALS SCIENCE↗

Design of Graphene/Ionic Liquid Composites for Carbon Capture

Pore size is a crucial factor impacting gas separation in porous separation materials, but how to control the pore size to optimize the separation performance remains a challenge. Here, we propose a design of graphene/ionic liquid composites with tunable slit pore sizes, where cations and anions of ionic liquids are intercalated between graphene layers. By varying the sizes of the ions, we show from first-principles density functional theory calculations that the accessible pore size can be tuned from 3.4 to 6.0 Å. Grand canonical Monte Carlo simulations of gas sorption find that the composite materials possess high CO 2 uptake at room temperature and 1 bar (up to ~8.5 mmol/g). Further simulations of the sorption of gas mixtures reveal that high CO 2 /N 2 and CO 2 /CH 4 adsorption selectivities can be obtained when the accessible pore size is <5 Å. This work suggests a new strategy to achieve tunable pore sizes via the graphene/IL composites for highly selective CO 2 /N 2 and CO 2 /CH 4 adsorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unraveling electrochemo-mechanical aspects of core–shell composite cathode for sulfide based all-solid-state batteries

All-solid-state lithium batteries (ASSLBs) are emerging as promising next-generation batteries for electric vehicles owing to their high energy densities and safety features. However, challenges such as inadequate material percolation and low cathode utilization often hinder their potential. This paper presents a core–shell approach to optimize the cathode active material (CAM) utilization. The resultant CAM composite showed high ionic conductivity, a highly dense microstructure with <10% porosity, and minimal stack pressure changes during electrochemical cycling. The maximum CAM utilization was achieved while effectively mitigating electrochemo-mechanical side reactions by applying a uniformly coated Li 6 PS 5 Cl solid electrolyte layer (≈500 nm) and a LiNbO 3 buffer layer (≈10 nm) onto LiNi 0.8 Mn 0.1 Co 0.1 O 2 particles (LPSCl@LNO@NMC). The engineered LPSCl@LNO@NMC composites, which incorporated a 5 wt% LPSCl coating on LNO@NMC powders, exhibited a dense microstructure that enhanced the mechanical stability at the cathode. Sulfide-based solid electrolyte (SSE)/SSE contact provided better ionic pathways within the composite and increased CAM utilization. Thus, an enhanced reversible capacity (197 mA h g -1 ) and exceptional high-rate cycling performance (86.3% capacity retention after 1000 cycles at 2C) were observed. These findings pave the way for the advancement and commercialization of high-performance ASSLBs.

25 ENERGY STORAGE↗

Multi-fidelity machine-learning with uncertainty quantification and Bayesian optimization for materials design: Application to ternary random alloys

We present a scale-bridging approach based on a multi-fidelity (MF) machine-learning (ML) framework leveraging Gaussian processes (GP) to fuse atomistic computational model predictions across multiple levels of fidelity. Through the posterior variance of the MFGP, our framework naturally enables uncertainty quantification, providing estimates of confidence in the predictions. We used density functional theory as high-fidelity prediction, while a ML interatomic potential is used as low-fidelity prediction. Practical materials’ design efficiency is demonstrated by reproducing the ternary composition dependence of a quantity of interest (bulk modulus) across the full aluminum–niobium–titanium ternary random alloy composition space. The MFGP is then coupled to a Bayesian optimization procedure, and the computational efficiency of this approach is demonstrated by performing an on-the-fly search for the global optimum of bulk modulus in the ternary composition space. The framework presented in this manuscript is the first application of MFGP to atomistic materials simulations fusing predictions between density functional theory and classical interatomic potential calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optical properties of hybrid quantum-well–dots nanostructures grown by MOCVD

The deposition of In{sub x}Ga{sub 1–x}As with an indium content of 0.3–0.5 and an average thickness of 3–27 single layers on a GaAs wafer by metalorganic chemical vapor deposition (MOCVD) at low temperatures results in the appearance of thickness and composition modulations in the layers being formed. Such structures can be considered to be intermediate nanostructures between ideal quantum wells and quantum dots. Depending on the average thickness and composition of the layers, the wavelength of the photoluminescence peak for the hybrid InGaAs quantum well–dots nanostructures varies from 950 to 1100 nm. The optimal average In{sub x}Ga{sub 1–x}As thicknesses and compositions at which the emission wavelength is the longest with a high quantum efficiency retained are determined.

36 MATERIALS SCIENCE↗

Optimized setup for two-dimensional convection experiments in thin liquid films

We present a novel experimental setup to investigate two-dimensional thermal convection in a freestanding thin liquid film. Such films can be produced in a controlled way on the scale of 5–1000 nm. Our primary goal is to investigate convection patterns and the statistics of reversals in Rayleigh-Bénard convection with varying aspect ratio. Additionally, questions regarding the physics of liquid films under controlled conditions can be investigated, like surface forces, or stability under varying thermodynamical parameters. The film is suspended in a frame which can be adjusted in height and width to span an aspect ratio range of Γ = 0.16–10. The top and bottom frame elements can be set to specific temperature within T = 15 °C to 55 °C. A thickness to area ratio of approximately 10{sup 8} enables only two-dimensional fluid motion in the time scales relevant for turbulent motion. The chemical composition of the film is well-defined and optimized for film stability and reproducibility and in combination with carefully controlled ambient parameters allows the comparison to existing experimental and numerical data.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A conceptual geochemical model of the geothermal system at Surprise Valley, CA

Characterizing the geothermal system at Surprise Valley (SV), northeastern California, is important for determining the sustainability of the energy resource, and mitigating hazards associated with hydrothermal eruptions that last occurred in 1951. Previous geochemical studies of the area attempted to reconcile different hot spring compositions on the western and eastern sides of the valley using scenarios of dilution, equilibration at low temperatures, surface evaporation, and differences in rock type along flow paths. These models were primarily supported using classical geothermometry methods, and generally assumed that fluids in the Lake City mud volcano area on the western side of the valley best reflect the composition of a deep geothermal fluid. In this contribution, we address controls on hot spring compositions using a different suite of geochemical tools, including optimized multicomponent geochemistry (GeoT) models, hot spring fluid major and trace element measurements, mineralogical observations, and stable isotope measurements of hot spring fluids and precipitated carbonates. We synthesize the results into a conceptual geochemical model of the Surprise Valley geothermal system, and show that high-temperature (quartz, Na/K, Na/K/Ca) classical geothermometers fail to predict maximum subsurface temperatures because fluids re-equilibrated at progressively lower temperatures during outflow, including in the Lake City area. We propose a model where hot spring fluids originate as a mixture between a deep thermal brine and modern meteoric fluids, with a seasonally variable mixing ratio. The deep brine has deuterium values at least 3 to 4‰ lighter than any known groundwater or high-elevation snow previously measured in and adjacent to SV, suggesting it was recharged during the Pleistocene when meteoric fluids had lower deuterium values. The deuterium values and compositional characteristics of the deep brine have only been identified in thermal springs and groundwater samples collected in proximity to structures that transmit thermal fluids, suggesting the brine may be thermal in nature. On the western side of the valley at the Lake City mud volcano, the deep brine-meteoric water mixture subsequently boils in the shallow subsurface, precipitates calcite, and re-equilibrates at about 130 °C. On the eastern side of the valley, meteoric fluid mixes to a greater extent with the deep brine, cools conductively without boiling, and the composition is modified as dissolved elements are sequestered by secondary minerals that form along the cooling and outflow path at temperatures <130 °C. Re-equilibration of geothermal fluids at lower temperatures during outflow explains why subsurface temperature estimates based on classical geothermometry methods are highly variable, and fail to agree with temperature estimates based on dissolved sulfate-oxygen isotopes and results of classical and multicomponent geothermometry applied to reconstructed deep well fluids. Furthermore, the proposed model is compatible with the idea suggested by others that thermal fluids on the western and eastern side of the valley have a common source, and supports the hypothesis that low temperature re-equilibration during west to east flow is the major control on hot spring fluid compositions, rather than dilution, evaporation, or differences in rock type.

15 GEOTHERMAL ENERGY↗

An optimized three-dimensional linear-electric-field time-of-flight analyzer

In situ measurements of the dynamics and composition of space plasmas have greatly improved our understanding of the space environment. In particular, mass spectrometers that use a combination of electrostatic analyzers and time-of-flight systems can identify revealing dynamic and compositional characteristics of ions, and thus constrain their sources and the physical processes relevant for their transport. We demonstrate an optimized design of a linear-electric-field time-of-flight technology that can be used to obtain a high signal to noise: ions that follow an energy-isochronous oscillation within the instrument impact an emissive plate and cause secondary electrons to be sent toward the detector, triggering a high-resolution measurement. By focusing these secondary electrons to a central area on a position-sensitive anode, their signals are separated from ions and neutrals that do not experience energy-isochronous motion. Using their impact positions, the high mass resolution measurements are easily distinguished from other signals on the detector, leading to very favorable signal-to-noise ratios. This optimization provides an improvement to existing technologies without increasing the instrument size or complexity, and uses a novel time-of-flight circuit that combines timing and position information from many signals and ions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Multimodal X-ray nano-spectromicroscopy analysis of chemically heterogeneous systems

Abstract Understanding the nanoscale chemical speciation of heterogeneous systems in their native environment is critical for several disciplines such as life and environmental sciences, biogeochemistry, and materials science. Synchrotron-based X-ray spectromicroscopy tools are widely used to understand the chemistry and morphology of complex material systems owing to their high penetration depth and sensitivity. The multidimensional (4D+) structure of spectromicroscopy data poses visualization and data-reduction challenges. This paper reports the strategies for the visualization and analysis of spectromicroscopy data. We created a new graphical user interface and data analysis platform named XMIDAS (X-ray multimodal image data analysis software) to visualize spectromicroscopy data from both image and spectrum representations. The interactive data analysis toolkit combined conventional analysis methods with well-established machine learning classification algorithms (e.g. nonnegative matrix factorization) for data reduction. The data visualization and analysis methodologies were then defined and optimized using a model particle aggregate with known chemical composition. Nanoprobe-based X-ray fluorescence (nano-XRF) and X-ray absorption near edge structure (nano-XANES) spectromicroscopy techniques were used to probe elemental and chemical state information of the aggregate sample. We illustrated the complete chemical speciation methodology of the model particle by using XMIDAS. Next, we demonstrated the application of this approach in detecting and characterizing nanoparticles associated with alveolar macrophages. Our multimodal approach combining nano-XRF, nano-XANES, and differential phase-contrast imaging efficiently visualizes the chemistry of localized nanostructure with the morphology. We believe that the optimized data-reduction strategies and tool development will facilitate the analysis of complex biological and environmental samples using X-ray spectromicroscopy techniques.

36 MATERIALS SCIENCE↗

Integrated Computational Materials Engineering Development of Carbon Fiber Composites for Lightweight Vehicles

This project, Integrated Computational Materials Engineering Development of Carbon Fiber Composites for Lightweight Vehicles, develops Integrated Computational Materials Engineering (ICME) techniques for Carbon Fiber Reinforced Polymer (CFRP) composites and uses these ICME tools within a multi-disciplinary optimization scheme to design a carbon-fiber intensive front subframe for a passenger sedan. The subframe is a structural automotive component with stringent requirements for vibration, strength, durability and safety performance. CFRP composites, with a density of 1.55 g/cm3 and a tensile strength of up to 2,000 MPa in the fiber direction, have a high strength-to-weight ratio, making them one of the most promising candidates to replace the metals currently used for automotive structural components. By increasing the accessibility of CFRP component designs, reducing development-to-deployment lead time of CFRP components, and improving the robustness of initial designs, this project supports weight reduction in light-duty vehicles. These efforts can help mitigate greenhouse gas emissions from passenger vehicles and have the potential to improve national energy independence.

36 MATERIALS SCIENCE↗

Integrated Computational Materials Engineering Development of Carbon Fiber Composites for Lightweight Vehicles

This project, Integrated Computational Materials Engineering Development of Carbon Fiber Composites for Lightweight Vehicles, develops Integrated Computational Materials Engineering (ICME) techniques for Carbon Fiber Reinforced Polymer (CFRP) composites and uses these ICME tools within a multi-disciplinary optimization scheme to design a carbon-fiber intensive front subframe for a passenger sedan. The subframe is a structural automotive component with stringent requirements for vibration, strength, durability and safety performance. CFRP composites, with a density of 1.55 g/cm 3 and a tensile strength of up to 2,000 MPa in the fiber direction, have a high strength-to-weight ratio, making them one of the most promising candidates to replace the metals currently used for automotive structural components. By increasing the accessibility of CFRP component designs, reducing development-to-deployment lead time of CFRP components, and improving the robustness of initial designs, this project supports weight reduction in light-duty vehicles. These efforts can help mitigate greenhouse gas emissions from passenger vehicles and have the potential to improve national energy independence.

36 MATERIALS SCIENCE↗

Composition dependent intrinsic defect structures in SrTiO3

Intrinsic point defect complexes in SrTiO3 under different chemical conditions are studied using density functional theory. The Schottky defect complex consisting of nominally charged Sr, Ti and O vacancies is predicted to be the most stable defect structure in stoichiometric SrTiO3, with a relatively low formation energy of 1.64 eV/defect. In addition, the mechanisms of defect complex formation in nonstoichiometric SrTiO3 are investigated. Excess SrO leads to the formation of the oxygen vacancies and a strontium-titanium antisite defect, while a strontium vacancy together with an oxygen vacancy and the titanium-strontium antisite defect are produced in an excess TiO2 environment. Since point defects, such as oxygen vacancies and cation antisite defects, are intimately related to the functionality of SrTiO3, these results provide guidelines for controlling the formation of intrinsic point defects and optimizing the functionality of SrTiO3 by controlling nonstoichiometric chemical compositions of SrO and TiO2 in experiments.

defects↗

Lightweight Aluminum/Nano composites for Automotive Drive Train Applications

During Phase I, we successfully processed air atomized aluminum powders via Dynamic Magnetic Compaction (DMC) pressing and subsequent sintering to produce parts with properties similar to wrought aluminum. We have also showed for the first time that aluminum powders can be processed without lubes via press and sintering to 100 % density. This will preclude a delube cycle in sintering and promote environmentally friendly P/M processing. Processing aluminum powders via press and sintering with minimum shrinkage will enable net shape fabrication. Aluminum powders processed via a conventional powder metallurgy process produce too large a shrinkage. Because of this, sinter parts have to be machined into specific net shape. This results in increased scrap and cost. Fully sintered aluminum alloy under this Phase I project has shown good particle-to-particle bonding and mechanical properties. We have also shown the feasibility of preparing nano composite powders and processing via pressing and sintering. This was accomplished by dispersing nano silicon carbide (SiC) powders into aluminum matrix comprising micron-sized powders (<100 microns) using a proprietary process. These composite powders of Al with nano SiC were processed using DMC press and sinter process to sinter density of 85-90%. The process optimization along with sintering needs to be carried out to produce full density composites.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Flexible Coal: Evolution from Baseload to Peaking Plant (Brochure)

Twenty-first century power systems, with higher penetration levels of low-carbon energy, smart grids, and other emerging technologies, will favor resources that have low marginal costs and provide system flexibility (e.g., the ability to cycle on and off to follow changes in variable renewable energy plant output). Questions remain about both the fate of coal plants in this scenario and whether they can cost-effectively continue to operate if they cycle routinely. The experience from the CGS plant demonstrates that coal plants can become flexible resources. This flexibility - namely the ability to cycle on and off and run at lower output (below 40% of capacity) - requires limited hardware modifications but extensive modifications to operational practice. Cycling does damage the plant and impact its life expectancy compared to baseload operations. Nevertheless, strategic modifications, proactive inspections and training programs, among other operational changes to accommodate cycling, can minimize the extent of damage and optimize the cost of maintenance. CGS's cycling, but not necessarily the associated price tag, is replicable. Context - namely, power market opportunities and composition of the generation fleet - will help determine for other coal plants the optimal balance between the level of cycling-related forced outages and the level of capital investment required to minimize those outages. Replicating CGS's experience elsewhere will likely require a higher acceptance of forced outages than regulators and plant operators are accustomed to; however, an increase in strategic maintenance can minimize the impact on outage rates.

01 COAL, LIGNITE, AND PEAT↗