Search NASA⌕ Search

SEARCH · Search NASA

Results for “conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Phonon focusing and temperature dependences of thermal conductivity of silicon nanofilms

The effect of phonon focusing on the anisotropy and temperature dependences of the thermal conductivities of silicon nanofilms is analyzed using the three-mode Callaway model. The orientations of the film planes and the directions of the heat flux for maximal or minimal heat removal from silicon chip elements at low temperatures, as well as at room temperature, are determined. It is shown that in the case of diffuse reflection of phonons from the boundaries, the plane with the (100) orientation exhibits the lowest scattering ability (and the highest thermal conductivity), while the plane with the (111) orientation is characterized by the highest scattering ability (and the lowest thermal conductivity). The thermal conductivity of wide films is determined to a considerable extent by the orientation of the film plane, while for nanowires with a square cross section, the thermal conductivity is mainly determined by the direction of the heat flux. The effect of elastic energy anisotropy on the dependences of the thermal conductivity on the geometrical parameters of films is analyzed. The temperatures of transition from boundary scattering to bulk relaxation mechanisms are determined.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Conductivity of metal vapors at the critical point

The conductivity of metal vapors at the critical point and near it has been considered. The liquid-metal conductivity originates in this region. The thermodynamic parameters of the critical point, the density of conduction electrons, and the conductivities of various metal vapors have been calculated within the unified approach. It has been proposed to consider the conductivity at the critical point—critical conductivity—as the fourth critical parameter in addition to the density, temperature, and pressure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An Effect of Chemical Modification of Surface of Carbon Nanotubes on Their Thermal Conductivity

An effect of partial chemical modification of the surface of a single-walled carbon nanotube on its thermal conductivity is studied. Numerical simulation of heat transfer showed that partial hydrogenation (fluorination) of a nanotube (addition of hydrogen and fluorine atoms from its outer side) can lead to more than a tenfold decrease in thermal conductivity. When the length of the nanotube increases, its thermal conductivity increases in proportion to the logarithm of the length, whereas the proportionality coefficient decreases with an increase in density of hydrogen or fluorine atoms attached. A thermal conductivity reduction coefficient does not depend on the length of the nanotube, but depends on temperature (the lower the temperature, the stronger the decrease) and density of the attached atoms p. When p < 0.25, an increase in density monotonically decreases the thermal conductivity. A decrease is maximum, when density p is 0.25. If only one half of the nanotube is hydrogenated, this half has a lower thermal conductivity. Such a nanotube becomes anisotropic and can be used as a heat transfer rectifier with no more than two percent rectification efficiency.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

An Investigation of LSF-YSZ Conductive Scaffolds for Infiltrated SOFC Cathodes

Porous composites of Sr-doped LaFeO 3 (LSF) and yttria-stabilized zirconia (YSZ) were investigated as conductive scaffolds for infiltrated SOFC cathodes with the goal of producing scaffolds for which only a few perovskite infiltration steps are required to achieve sufficient conductivity. While no new phases form when LSF-YSZ composites are calcined to 1623 K, shifts in the lattice parameters indicate Zr can enter the perovskite phase. Measurements on dense, LSF-YSZ composites show that the level of Zr doping depends on the Sr:La ratio. Because conductivity of undoped LSF increases with Sr content while both the ionic and electronic conductivities of Zr-doped LSF decrease with the level of Zr in the perovskite phase, there is an optimum initial Sr content corresponding to La 0.9 Sr 0.1 FeO 3 (LSF91). Although scaffolds made with 100% LSF had a higher conductivity than scaffolds made with 50:50 LSF-YSZ mixtures, the 50:50 mixture provides the optimal interfacial structure with the electrolyte and sufficient conductivity, providing the best cathode performance upon infiltration of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF).

36 MATERIALS SCIENCE↗

Using data-science approaches to unravel insights for enhanced transport of lithium ions in single-ion conducting polymer electrolyte

Solid polymer electrolytes have yet to achieve the an ionic conductivity > 1 mS/cm at room temperature for realistic applications. This target implies the need to reduce the effective energy barriers of ion transport in polymer electrolytes to around 20 kJ/mol. In this work, we combine information extracted from existing experimental results with theoretical calculations to provide insights into ion transport in single-ion conductors (SICs) with a focus on lithium ion SICs. Through the analysis of temperature-dependent ionic conductivity data obtained from the literature, we evaluate different methods of extracting energy barriers for lithium transport. The traditional Arrhenius fit to the temperature-dependent ionic conductivity data indicates that the Meyer-Neldel rule holds for SICs. However, the values of the fitting parameters remain unphysical. Our modified approach based on recent work (Macromolecules, 56, 15, 6051(2023)), which incorporates a fixed pre-exponential factor, reveals that the energy barriers exhibit temperature dependence over a wide range of temperatures. Using this approach, we identify a series of anions leading to the energy barriers less than 30 kJ/mol, which include trifluoromethane sulfonimide (TFSI), fluoromethane sulfonimide (FSI), and boron-based organic anions. In our efforts to design the next generation of anions, which can exhibit the energy barriers less than 20 kJ/mol, we focused on boron-containing SICs, and performed density functional theory (DFT) based calculations to connect the chemical structures via the binding energy of cation (lithium)-anion pairs with the experimentally derived effective energy barriers for ion transport. Not only have we identified a correlation between the binding energy and the energy barriers, but we also propose a strategy to design new boron-based anions by using the correlation. This combined approach involving experiments and theoretical calculations is capable of facilitating the identification of promising new anions, which can exhibit ionic conductivity $> 1$ mS/cm near room temperature, thereby expediting the development of novel superionic single-ion conducting polymer electrolytes. The published datasets include all the temperature-dependent ionic conductivity collected from the literature with literature DOIs, DFT calculated binding energies, and python scripts to analyze data, construct statistical models, and generate plots.

36 MATERIALS SCIENCE↗

High Temperature, Low Relative Humidity, Polymer-type Membranes Based on Disulfonated Poly(arylene ether) Block and Random Copolymers Optionally Incorporating Protonic Conducting Layered Water insoluble Zirconium Fillers

Our research group has been engaged in the past few years in the synthesis of biphenol based partially disulfonated poly(arylene ether sulfone) random copolymers as potential PEMs. This series of polymers are named as BPSH-xx, where BP stands for biphenol, S stands for sulfonated, H stands for acidified and xx represents the degree of disulfonation. All of these sulfonated copolymers phase separate to form nano scale hydrophilic and hydrophobic morphological domains. The hydrophilic phase containing the sulfonic acid moieties causes the copolymer to absorb water. Water confined in hydrophilic pores in concert with the sulfonic acid groups serve the critical function of proton (ion) conduction and water transport in these systems. Both Nafion and BPSH show high proton conductivity at fully hydrated conditions. However proton transport is especially limited at low hydration level for the BPSH random copolymer. It has been observed that the diffusion coefficients of both water and protons change with the water content of the pore. This change in proton and water transport mechanisms with hydration level has been attributed to the solvation of the acid groups and the amount of bound and bulk-like water within a pore. At low hydration levels most of the water is tightly associated with sulfonic groups and has a low diffusion coefficient. This tends to encourage isolated domain morphology. Thus, although there may be significant concentrations of protons, the transport is limited by the discontinuous morphological structure. Hence the challenge lies in how to modify the chemistry of the polymers to obtain significant protonic conductivity at low hydration levels. This may be possible if one can alter the chemical structure to synthesize nanophase separated ion containing block copolymers. Unlike the BPSH copolymers, where the sulfonic acid groups are randomly distributed along the chain, the multiblock copolymers will feature an ordered sequence of hydrophilic and hydrophobic segments. If, like in Nafion, connectivity is established between the hydrophilic domains in these multiblock copolymers, they will not need as much water, and hence will show much better protonic conductivity than the random copolymers (with similar degree of sulfonation, or IEC) at partially hydrated conditions. The goal of this research is to develop a material suitable for use as a polymer electrolyte membrane which by the year 2010 will meet all the performance requirements associated with fuel cell operation at high temperatures and low relative humidity, and will out-perform the present standard Nafion{reg_sign}. In particular, it is our objective to extend our previous research based on the use of thermally, oxidatively, and hydrolytically, ductile, high Tg ion containing polymers based on poly(arylene ethers) to the production of polymer electrolyte membranes which will meet all the performance requirements in addition to having an areal resistance of < 0.05 ohm-cm{sup 2} at a temperature of up to 120 C, relative humidity of 25 to 50%, and up to 2.5 atm total pressure. In many instances, our materials already out performs Nafion{reg_sign}, and it is expected that with some modification by either combining with conductive inorganic fillers and/or synthesizing as a block copolymer it will meet the performance criteria at high temperatures and low relative humidity. A key component in improving the performance of the membranes (and in particular proton conductivity) and meeting the cost requirements of $40/m{sup 2} is our development of a film casting process, which shows promise for generation of void free thin films of uniform thickness with controlled polymer alignment and configuration.

30 DIRECT ENERGY CONVERSION↗

The thermal conductivity of mixed fuel U x Pu 1-x O 2 : molecular dynamics simulations

Mixed oxides (MOX), in the context of nuclear fuels, are a mixture of the oxides of heavy actinide elements such as uranium, plutonium and thorium. The interest in the UO 2 -PuO 2 system arises from the fact that these oxides are used both in fast breeder reactors (FBRs) as well as in pressurized water reactors (PWRs). The thermal conductivity of UO 2 fuel is an important material property that affects fuel performance since it is the key parameter determining the temperature distribution in the fuel, thus governing, e.g., dimensional changes due to thermal expansion, fission gas release rates, etc. For this reason it is important to understand the thermal conductivity of MOX fuel and how it differs from UO 2 . Here, molecular dynamics (MD) simulations are carried out to determine quantitatively, the effect of mixing on the thermal conductivity of U x Pu 1-x O 2 , as a function of PuO 2 concentrations, for a range of temperatures, 300 – 1500 K. The results will be used to develop enhanced continuum thermal conductivity models for MARMOT and BISON by INL. These models express the thermal conductivity as a function of microstructure state-variables, thus enabling thermal conductivity models with closer connection to the physical state of the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NanoCapillary Network Proton Conducting Membranes for High Temperature Hydrogen/Air Fuel Cells

The objective of this proposal is to fabricate and characterize a new class of NanoCapillary Network (NCN) proton conducting membranes for hydrogen/air fuel cells that operate under high temperature, low humidity conditions. The membranes will be intelligently designed, where a high density interconnecting 3-D network of nm-diameter electrospun proton conducting polymer fibers is embedded in an inert (uncharged) water/gas impermeable polymer matrix. The high density of fibers in the resulting mat and the high ion-exchange capacity of the fiber polymer will ensure high proton conductivity. To further enhance water retention, molecular silica will be added to the sulfonated polymer fibers. The uncharged matrix material will control water swelling of the high ion-exchange capacity proton conducting polymer fibers and will impart toughness to the final nanocapillary composite membrane. Thus, unlike other fuel cell membranes, the role of the polymer support matrix will be decoupled from that of the proton-conducting channels. The expected final outcome of this 5-year project is the fabrication of fuel cell membranes with properties that exceed the DOE’s technical targets, in particular a proton conductivity of 0.1 S/cm at a temperature less than or equal to120°C and 25-50% relative humidity.

30 DIRECT ENERGY CONVERSION↗

NSUF RTE completion report for 23-4780: Microstructural Defect Induced Thermal Conductivity Reduction in Uranium Nitride and Thorium Nitride

Uranium nitride (UN) is known to have a higher thermal conductivity than traditional oxide fuels, which could lead to a more efficient energy transport and lower local temperature during its lifetime. But the thermal transport performance of UN in extreme environments has not been systematic studied. This study investigated the irradiation induced microstructural defects in UN and the impacts on thermal conductivity. The samples were produced by spark plasma sintering at University of Texas-San Antonio (UTSA), Los Alamos National Laboratory (LANL), and Idaho National Laboratory (INL). Thermal conductivity of UN before and after 2MeV proton irradiation were measured by using laser metrology at INL in a temperature range of 77-295K. Thermal conductivity measurements in this wide, cryogenic temperature range is critical to understand the phonon scattering mechanisms between the thermal energy carrier, phonons, and different types of irradiation-induced defects. In order to ensure the measurements were conducted in the same grains and minimize the impact of the local heterogeneities, the measurement locations were highlighted by fiducial marks using the focused ion beam (FIB) with grain orientation identified using the electron backscatter diffraction (EBSD) at the Center of Advanced Energy Studies (CAES). Irradiation experiment was conducted at the Ion Beam Laboratory at Texas A&M University (TAMU). A total of 6 samples were irradiated with different irradiation doses and temperatures. After irradiation, the microstructure was characterized by using Transmission Electron Microscope (TEM) at CAES (also in the FIB marks).

36 - MATERIALS SCIENCE↗

The Evaporation and Survival of Cluster Galaxy Coronae. I. The Effectiveness of Isotropic Thermal Conduction Including Saturation

We simulate the evolution of cluster galaxy hot interstellar medium (ISM) gas that is a result of the effects of ram pressure and thermal conduction in the intracluster medium (ICM). At the density and temperature of the ICM, the mean free paths of ICM electrons are comparable to the sizes of galaxies, therefore electrons can efficiently transport heat that is due to thermal conduction from the hot ICM to the cooler ISM. Galaxies consisting of dark matter halos and hot gas coronae are embedded in an ICM-like “wind tunnel” in our simulations. In this paper, we assume that thermal conduction is isotropic and include the effects of saturation. We find that as heat is transferred from the ICM to the ISM, the cooler denser ISM expands and evaporates. This process is significantly faster than gas loss due to ram pressure stripping; for our standard model galaxy, the evaporation time is 160 Myr, while the ram pressure stripping timescale is 2.5 Gyr. Thermal conduction also suppresses the formation of shear instabilities, and there are no stripped ISM tails since the ISM evaporates before tails can form. Observations of long-lived X-ray emitting coronae and ram pressure stripped X-ray tails in galaxies in group and cluster environments therefore require that thermal conduction is suppressed or offset by some additional physical process. The most likely process is anisotropic thermal conduction that is due to magnetic fields in the ISM and ICM, which we simulate and study in the next paper in this series.

79 ASTRONOMY AND ASTROPHYSICS↗

The Evaporation and Survival of Cluster Galaxies’ Coronae. II. The Effectiveness of Anisotropic Thermal Conduction and Survival of Stripped Galactic Tails

We simulate anisotropic thermal conduction between the intracluster medium (ICM) and the hot coronal interstellar medium (ISM) gas in cluster galaxies. In Paper I, we simulated the evaporation of the hot ISM due to isotropic (possibly saturated) conduction between the ISM and ICM. We found that hot coronae evaporate on ∼10{sup 2} Myr timescales, significantly shorter than the ∼10{sup 3} Myr gas loss times due to ram pressure stripping. No tails of stripped gas are formed. This is in tension with the observed ubiquity and implied longevity of compact X-ray coronae and stripped ISM tails, and requires the suppression of evaporation, possibly due to magnetic fields and anisotropic conduction. We perform a series of wind tunnel simulations similar to that in Paper I, now including ISM and ICM magnetic fields. We simulate the effect of anisotropic conduction for a range of extreme magnetic field configurations: parallel and perpendicular to the ICM wind, and continuous and completely disjointed between the ISM and ICM. We find that when conduction is anisotropic, gas loss due to evaporation is severely reduced; the overall gas loss rates with and without anisotropic conduction do not differ by more than 10%–20%. Magnetic fields also prevent stripped tails from evaporating in the ICM by shielding, and providing few pathways for heat transport between the ICM and ISM. The morphology of stripped tails and magnetic fields in the tails and wakes of galaxies are sensitive to the initial magnetic field configuration.

79 ASTRONOMY AND ASTROPHYSICS↗

RF Characterization of a Photocurable PEDOT:PSS:PEGDA Conductive Biomaterial for 3D-Printing Implantable Antennas

In this work, we demonstrate photocurable PEDOT:PSS:PEGDA biomaterial as a promising candidate for intracorporeal 3D printing. Intracorporeal 3D printing offers a less invasive method which offer flexibility to tailor the form factor of printed structures. Previous work has demonstrated the feasibility of a robotic probe to 3D-print biological tissues intracorporeally via a minor incision. This same probe could also 3D-print implantable antennas as long as a suitable conductive material is identified in terms of conductivity, biocompatibility, and ability to cure at room/body temperature for safety purposes. We assess the frequency-dependent conductivity of this biomaterial and explore the Radio-Frequency (RF) performance of resulting antennas operating in free-space and inside tissue-emulating phantoms. Results show that PEDOT:PSS biomaterial with 21% and 30% PEGDA content exhibit a conductivity of ~10 4 S/m up to 5 GHz, suitable for wireless implants. Comparing the two, 21% PEGDA content exhibits poorer curing abilities, while 30% PEGDA exhibits slightly lower conductivity. Measurements for 2.4 GHz free-space dipoles conducted in an anechoic chamber reveal only ~0.8 dB and ~1 dB lower gain for PEDOT:PSS:21%PEGDA and PEDOT:PSS:30%PEGDA biomaterial, respectively, as compared to their copper counterpart. For a 5 mm-deep implanted patch antenna, these two biomaterials exhibit 3.05 dB and 3.84 dB higher transmission loss than copper, respectively. If deemed necessary, this performance degradation can be overcome by increasing the overall antenna size since the printing process is now minimally invasive and miniaturization requirements can be relaxed.

3D-printing↗

Status Report on Separate Effects Testing of Thermal Conductivity of U-Zr Alloy

Phases by definition in an alloy system have distinct physical and chemical properties, including thermal conductivity. The goal of this multi-year study is to show that the different phases present in the U-Zr system indeed do have different thermal conductivities. This study will provide meso-scale (10-100 µm) experimental observations using the Thermal Conductivity Microscope (TCM) of phase dependent thermal conductivity. The results of this study may indicate the need to reconsider the application of homogeneous medium assumption for metallic nuclear fuel that is currently used in fuel performance modeling, and could provide input for improving such model using a heterogeneous phase dependent assessment of thermal properties. The local thermal conductivity values from the TCM will be compared to the bulk measurements to validate this work. Twelve alloy samples with varying Zr compositions and heat treatments were fabricated for the initial phase of this study to characterize the individual phases present in the U-Zr system. The gamma body-centered cubic (BCC) phase was successfully identified in the appropriate size for TCM measurement. Next steps in this work will include identification of remaining phases in the U-Zr alloy system. Thermal conductivity will be measured in those phase areas of the materials and used to assess fuel performance codes for improvements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effective thermal conductivity of binary mixed materials with and without heat generation - An empirical approach

An empirical approach to determine the effective thermal conductivity of a binary mixed material with heat generation is developed and reported. The approach is developed for a steady state problem with spherical geometry. The approach is based on two main ideas: a structural approximation and an empirical formulation. As for the structural approximation, the binary mixed material was assumed to be equivalent to a binary layered system of adjacent fuel and moderator layers oriented perpendicular to the heat flux. An empirical approach was then used to conduct a general correlation for the effective thermal conductivity of a binary layered system with heat generation. This empirical approach was conducted systematically by considering the parametric and operational condition effects of the system on the overall effective thermal conductivity. Results are then compared to some experimental data as well as with thermal conductivity values predicted by an empirical correlation that is based on experimental data. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Controlled Hysteresis of Conductance in Molecular Tunneling Junctions

The problem this paper addresses is the origin of the hysteretic behavior in two-terminal molecular junctions made from an EGaIn electrode and self-assembled monolayers of alkanethiolates terminated in chelates (transition metal dichlorides complexed with 2,2'-bipyridine; BIPY-MCl 2 ). The hysteresis of conductance displayed by these BIPY-MCl 2 junctions changes in magnitude depending on the identity of the metal ion (M) and the window of the applied voltage across the junction. The hysteretic behavior of conductance in these junctions appears only in an incoherent (Fowler–Nordheim) tunneling regime. When the complexed metal ion is Mn(II), Fe(II), Co(II), or Ni(II), both incoherent tunneling and hysteresis are observed for a voltage range between +1.0 V and –1.0 V. When the metal ion is Cr(II) or Cu(II), however, only resonant (one-step) tunneling is observed, and the junctions exhibit no hysteresis and do not enter the incoherent tunneling regime. Using this correlation, the conductance characteristics of BIPY-MCl 2 junctions can be controlled. Furthermore, this voltage-induced change of conductance demonstrates a simple, fast, and reversible way (i.e., by changing the applied voltage) to modulate conductance in molecular tunneling junctions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High Conductivity and Electron-Transfer Validation in an n-Type Fluoride-Anion-Doped Polymer for Thermoelectrics in Air

Air-stable and soluble tetrabutylammonium fluoride (TBAF) is demonstrated as an efficient n-type dopant for the conjugated polymer ClBDPPV. Electron transfer from F - anions to the π-electron-deficient ClBDPPV through anion–π electronic interactions is strongly corroborated by the combined results of electron spin resonance, UV–vis–NIR, and ultraviolet photoelectron spectroscopy. Doping of ClBDPPV with 25 mol% TBAF boosts electrical conductivity to up to 0.62 S cm -1 , among the highest conductivities that have been reported for solution-processed n-type conjugated polymers, with a thermoelectric power factor of 0.63 µW m -1 K -2 in air. Importantly, the Seebeck coefficient agrees with recently published correlations to conductivity. Moreover, the F - -doped ClBDPPV shows significant air stability, maintaining the conductivity of over 0.1 S cm -1 in a thick film after exposure to air for one week, to the best of our knowledge the first report of an air-stable solution-processable n-doped conductive polymer with this level of conductivity. The result shows that using solution-processable small-anion salts such as TBAF as an n-dopant of organic conjugated polymers possessing lower LUMO (lowest unoccupied molecular orbital), less than -4.2 eV) can open new opportunities toward high-performance air-stable solution-processable n-type thermoelectric (TE) conjugated polymers.

36 MATERIALS SCIENCE↗

Revisiting the Role of Conductivity and Polarity of Host Materials for Long-Life Lithium–Sulfur Battery

Despite their high theoretical energy density and low cost, lithium-sulfur batteries (LSBs) suffer from poor cycle life and low energy efficiency owing to the polysulfides shuttle and the electronic insulating nature of sulfur. Conductivity and polarity are two critical parameters for the search of optimal sulfur host materials. However, their role in immobilizing polysulfides and enhancing redox kinetics for long-life LSBs are not fully understood. In this work we have conducted an evaluation on the role of polarity over conductivity by using a polar but nonconductive platelet ordered mesoporous silica (pOMS) and its replica platelet ordered mesoporous carbon (pOMC), which is conductive but nonpolar. It is found that the polar pOMS/S cathode with a sulfur mass fraction of 80 wt% demonstrates outstanding long-term cycle stability for 2000 cycles even at a high current density of 2C. Furthermore, the pOMS/S cathode with a high sulfur loading of 6.5 mg cm -2 illustrates high areal and volumetric capacities with high capacity retention. Complementary physical and electrochemical probes clearly show that surface polarity and structure are more dominant factors for sulfur utilization efficiency and long-life, while the conductivity can be compensated by the conductive agent involved as a required electrode material during electrode preparation. The present findings shed new light on the design principles of sulfur hosts towards long-life and highly efficient LSBs.

25 ENERGY STORAGE↗

Silicon Wafers with Facet-Dependent Electrical Conductivity Properties

By breaking intrinsic Si (100) and (111) wafers to expose sharp {111} and {112} facets, electrical conductivity measurements on single and different silicon crystal faces were performed through contacts with two tungsten probes. While Si {100} and {110} faces are barely conductive at low applied voltages, as expected, the Si {112} surface is highly conductive and Si {111} surface also shows good conductivity. Asymmetrical I–V curves have been recorded for the {111}/{112}, {111}/{110}, and {112}/{110} facet combinations because of different degrees of conduction band bending at these crystal surfaces presenting different barrier heights to current flow. In particular, the {111}/{110} and {112}/{110} facet combinations give I–V curves resembling those of p–n junctions, suggesting a novel field effect transistor design is possible capitalizing on the pronounced facet-dependent electrical conductivity properties of silicon.

36 MATERIALS SCIENCE↗