Search NASA⌕ Search

SEARCH · Search NASA

Results for “correlation filter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Effects of Fuel Properties on Particle Number and Particle Mass Emissions from Lean and Stoichiometric Gasoline Direct Injection Engine Operation

Engine-out particle size distributions and soot mass emissions were measured from a gasoline direct injection (GDI) engine fueled by seven different gasoline formulations. Additionally, particle size distributions were simultaneously measured downstream of a catalyzed gasoline particulate filter (GPF) to determine the size resolved filtration efficiency. Stoichiometric, lean homogeneous, and lean stratified combustion modes were studied at four steady-state engine conditions. The particulate matter (PM) Index was calculated for each fuel as a function of the double bond equivalent and vapor pressure of the fuel components. There was generally poor correlation between particle number (PN)/PM mass emissions and the PM Index for steady state stoichiometric conditions with clean injectors, which emitted low particle concentrations. However, under high-load lean homogeneous conditions, there was good correlation between PN/PM mass emission and the PM Index, with the exception that the high ethanol content fuel produced significantly higher PM emissions than the other fuels. Under lean stratified conditions, most fuels produced similar particle size distributions and concentrations with the exception that the E50 fuel produced significantly lower concentrations than the other fuels. These results demonstrate the profound sensitivity of particle emissions from high ethanol content fuel to engine operating conditions. Additionally, these results show the predominant factor influencing particle formation is charge mixture formation, which fuel properties influence, but not as significantly as engine conditions. Here, the GPF reduced the tailpipe particle number concentrations by 60 - 95% and showed evidence of passive regeneration under higher load lean engine conditions (Temp>400°C, Lambda>1.3). Total PN filtration efficiencies ranged from ~60 % with a clean filter to greater than 95% with as little as 25 mg/L of soot loaded on the filter with a most penetrating particle size (MPPS) between 100 and 150 nm. The GPF results show that GPF regeneration can be achieved with the added fuel efficiency benefit of lean operation.

33 ADVANCED PROPULSION SYSTEMS↗

Electrostatic Design and Characterization of a 200 keV Photogun and Wien Spin Rotator

High-energy nuclear physics experiments at the Jefferson Lab Continuous Electron Beam Accelerator Facility (CEBAF) require high spin-polarization electron beams produced from strained super-lattice GaAs photocathodes activated to negative electron affinity in a high voltage photogun operating at 130 kV dc. A pair of Wien filter spin rotators in the injector provides precise control of the electron beam polarization at the end station target. An upgrade of the CEBAF injector to better support the upcoming Moller experiment requires increasing the electron beam energy to 200 keV, resulting in better transmission through injector apertures and improved photocathode lifetime. In addition, the energy increase is expected to reduce unwanted helicity correlated intensity and position systematics. These requirements led to the design of a shielding electrode described in this work, which minimizes the electric field at the triple-point junction and linearizes the potential along the insulator, thus reducing the risk of field emission induced insulator arcing. The Wien spin rotator design was modified for increasing the electric field from 1.6 to 2.7 MV/m and the magnetic field from 9.1 to 13 mT. The upgrades required detailed modeling in Solidworks, electrostatic simulations using CST, beam dynamics using GPT, device implementation, and in situ high voltage characterization of the world?s first 200 keV polarized photoelectron gun and compatible Wien filter spin rotator.

Palacios-Serrano, Gabriel↗

Digital preprocessing of SEASAT imagery

A model for radar image data is derived for use in developing enhancement techniques. This model describes the image data as the result of a multiplicative-convolved noise process. This information is then used to design a minimum mean square error (MMSE) filter. The resulting filter is implemented adaptively to change with local statistics. A radar image processing technique which provides the MMSE estimate inside homogeneous areas and tends to preserve edge structure is thus developed. This technique has been implemented and tested using digitally correlated SEASAT-A synthetic aperture radar (SAR) imagery.

Frost, V. S.↗

The Distribution of Titanium in Lunar Soils on the Basis of Sensor and In Situ Data Fusion

A variety of remote-sensing measurements have been used to map the distribution of elements on the Moon as a means of providing constraints on the processes from which its crust and major terranes originated. Discussed here is Ti, which is incorporated into refractory minerals such as ilmenite during the latter stages of differentiation, and is thus a most useful element for understanding mare basalt petrogenesis. One of the earliest Ti maps showed Ti variations in nearside maria on the basis of groundbased spectral reflectance measurements. A map of Ti derived from gamma-ray measurements on Apollo 15 and 16 was produced at about the same time, and was improved upon considerably by Davis and coworkers, who effectively removed sources of spurious variation from Fe and Al or REE (e.g., Th) interference, and calibrated Ti on the bases of landing-site soil averages. In recent years, spectral reflectance measurements from Clementine have been used by Lucey and coworkers to produce global Ti distribution maps as well. As we indicated previously, the Lucey and Davis maps agree to first order. Meanwhile, we are using the concept of sensor data fusion to combine measurements from the AGR (Apollo gamma-ray) and CSR (Clementine Spectral Reflectance) techniques with ground truth from lunar soils to utilize the differences between the two maps to understand the distribution of Ti within lunar soil components, as we have done with Fe. This technique should be verified and applied on Lunar Prospector gamma-ray measurements of Ti, as the calibrated data become available within the next couple of years. Lunar Ti is found principally in the mineral ilmenite, and is associated with certain components of lunar soil: crystalline Ilmenite mineral fragments and high Ti-bearing glass. All data indicate that Ti is associated with maria and mafic minerals. In AGR and CSR datasets, Ti is highest on the nearside and in the maria, particularly in southern Serenitatis/northern Tranquillitatis and northwestern Procellarum. Unlike CSR-derived values, AGR Ti values show modest increase (up to 0.7%) on the northern farside. Both techniques show a primarily unimodal distribution with a shoulder in the high Ti direction and a primary mode at approximately 0.2% (0.15% for CSR and 0.25% for AGR data), but the AGR Ti data have more structure in the shoulder, including an apparent minor mode at 1.2% Ti, representing non-highland areas. Recalibrating the two datasets on the basis of matching the peaks and range on the histograms would not account for this additional structure in the AGR data. Low Ti areas, which occur predominantly on the farside, are not represented well in the lunar sample collection, although several meteorites thought to be of lunar highland origin show Ti abundances averaging about 0.2%. (Error bars on AGR Ti values are about 0.5%.) Gamma-ray measurements reflect intrinsic Ti surface composition, regardless of the physical or chemical state of Ti. Lucey and coworkers have attempted to produce an equivalent bulk Ti map by normalizing the spectral feature at 415 nm to remove the effects of physical variations from soil to soil. The normalization is based on laboratory measurements of available samples, primarily nearside maria, and is undoubtedly optimized for the proportions in which Ti- components are found in these soils. In particular, mare soils tend to have a much higher proportion of opaque mineral grains, which appears to be well correlated with Ti abundance. The relationship between Ti abundance and proportion of Ti-bearing glass (weighted for Ti abundance) is not as direct. Also shows the relationship between landing site soil average, AGR, and CSR Ti abundances (with CSR filtered to match resolution and field of view of AGR data). AGR Ti values show the best agreement with Ti soil averages, CSR Ti values being somewhat higher in high-Ti soils, and lower in low-Ti soils. These results would tend to support the argument that the technique for deriving Ti from the CSR measurements is optimized for one of the primary Ti-bearing components, most likely opaque mineral grains, and is thus over-compensating and reporting higher Ti values in mare areas, and underreporting Ti in highland areas with much lower proportions of opaque mineral grains. More information is contained in original.

Clark, P. E.↗

Perceptual Classification Images from Vernier Acuity Masked by Noise

Letting external noise rather than internal noise limit discrimination performance allows information to be extracted about the observer's stimulus classification rule. A perceptual classification image is the correlation over trials between the noise amplitude at a spatial location and the observer's responses. If, for example, the observer followed the rule of the ideal observer, the perceptual classification image would be an estimate of the ideal observer filter, the difference between the two unmasked images being discriminated. Perceptual classification images were estimated for a vernier discrimination task. The display screen had 48 pixels per degree horizontally and vertically. The no-offset image had a dark horizontal line of 4 pixels, a 1 pixel space, and 4 more dark pixels. Classification images were based on 1600 discrimination trials with the line contrast adjusted to keep the error rate near 25 percent. In the offset image, the second line was one pixel higher. Unlike the ideal observer filter (a horizontal dipole), the observer perceptual classification images are strongly oriented. Fourier transforms of the classification images had a peak amplitude near one cycle per degree and an orientation near 25 degrees. The spatial spread is much more than image blur predicts, and probably indicates the spatial position uncertainty in the task.

Ahumada, A. J.↗

An improved calculation of the non-Gaussian halo mass function

The abundance of collapsed objects in the universe, or halo mass function, is an important theoretical tool in studying the effects of primordially generated non-Gaussianities on the large scale structure. The non-Gaussian mass function has been calculated by several authors in different ways, typically by exploiting the smallness of certain parameters which naturally appear in the calculation, to set up a perturbative expansion. We improve upon the existing results for the mass function by combining path integral methods and saddle point techniques (which have been separately applied in previous approaches). Additionally, we carefully account for the various scale dependent combinations of small parameters which appear. Some of these combinations in fact become of order unity for large mass scales and at high redshifts, and must therefore be treated non-perturbatively. Our approach allows us to do this, and also to account for multi-scale density correlations which appear in the calculation. We thus derive an accurate expression for the mass function which is based on approximations that are valid over a larger range of mass scales and redshifts than those of other authors. By tracking the terms ignored in the analysis, we estimate theoretical errors for our result and also for the results of others. We also discuss the complications introduced by the choice of smoothing filter function, which we take to be a top-hat in real space, and which leads to the dominant errors in our expression. Finally, we present a detailed comparison between the various expressions for the mass functions, exploring the accuracy and range of validity of each.

79 ASTRONOMY AND ASTROPHYSICS↗

Edaphic factors, successional status and functional traits drive habitat associations of trees in naturally regenerating tropical dry forests

Many past studies have examined individual environmental drivers of tropical tree species distributions, but edaphic and successional gradients have not been considered simultaneously. Furthermore, determining how functional traits influence species distributions along these gradients may help to elucidate mechanisms behind community assembly. To assess the influence of environmental filtering on tropical dry forest (TDF) tree species distributions, we used forest inventory data from sites with large edaphic and successional gradients in NW Costa Rica. Our goals were to determine (1) whether edaphic or successional factors are more important determinants of the abundance of individual tree species in regenerating TDF, (2) how species-level functional traits are related to edaphic and/or successional niche associations of tree species and (3) correlations between species-level edaphic and successional niche associations. The distributions of 82 focal tree species were strongly driven by both edaphic and successional gradients. Overall, 94% of species responded to soil chemistry, 89% to soil texture and 94% to stand age gradients. Some functional traits were correlated with the edaphic and successional niche associations of TDF tree species. Species that specialized on soils with high total nutrient concentrations had higher foliar nutrient concentrations (nitrogen and phosphorus) and lower leaf dry matter content (LDMC). Species with wider stand age niches had lower LDMC and wood density. There were no correlations between edaphic and successional niche optima of TDF tree species. Our results indicate that successional and edaphic gradients concurrently drive community assembly in regenerating TDF. Moreover, our work underscores the importance of considering how the functional characteristics of TDF trees dictate species distributions across environmental gradients.

54 ENVIRONMENTAL SCIENCES↗

Improved determination of the 𝛽−‾‾𝜈𝑒 angular correlation coefficient 𝑎 in free neutron decay with the 𝑎⁢SPECT spectrometer

We report on a precise measurement of the electron-antineutrino angular correlation (𝑎 coefficient) in free neutron beta decay from the 𝑎⁢SPECT experiment. The 𝑎 coefficient is inferred from the recoil energy spectrum of the protons which are detected in 4⁢𝜋 by the 𝑎⁢SPECT spectrometer using magnetic adiabatic collimation with an electrostatic filter. Data are presented from a 100-day run at the Institut Laue Langevin in 2013. The sources of systematic errors are considered and included in the final result. We obtain 𝑎=−0.10430⁢(84) which is the most precise measurement of the neutron 𝑎 coefficient to date. From this, the ratio of axial vector to vector coupling constants is derived giving |𝜆|=1.2677⁢(28).

Beck, Marcus↗

Quasi-biennial geomagnetic variation caused by the sun

Clear evidence for the existence of a quasi-biennial geomagnetic variation is shown by an analysis of annual averages of the horizontal (H) component of the geomagnetic field observed at five observatories. The analysis uses a numerical filter, which is equivalent to taking the second order time derivative of the time series. The cause for the variation is external to the earth because its amplitude depends on magnetic activity. The second order time derivative of H is well correlated with the corresponding time derivatives of the relative sunspot number and 10.7 cm solar flux. It is suggested that quasi-biennial oscillations observed in the geomagnetic field, cosmic rays, stratospheric zonal wind and temperature, total ozone, and other meteorological parameters could be produced by a common cause on the sun.

Sugiura, M.↗

Genesis of Apollo 15 olivine normative mare basalts - Trace element correlations

Chemical and petrographic studies of 21 Apollo 15 rake basalts are reported; one pyroxene-phyric basalt, four olivine-phyric basalts, 15 olivine microgabbros, and one brecciated basalt are distinguished. The olivine-normative basalts (i.e., all samples but the pyroxene-phyric basalt) show correlation trends of La/Sm vs. La and Sm/Eu vs. La that are within the observed dispersion ranges of La/Sm and Sm/Eu ratios for a single lava flow. Trace element fractionation trends in the sample could be due to mobilization (perhaps by filter pressing) of fractionated residual liquid during the crystallization of a lava flow. However, it is also possible that the suite of olivine-normative basalts represents several basalt flows produced by partial melting of cumulate layers having interstitial liquids with variable trace-element compositions.

Ma, M.-S.↗

Subsonic flight test evaluation of a propulsion system parameter estimation process for the F100 engine

An adaptive-performance-seeking control system which optimizes the quasi-steady-state performance of the F-15 propulsion system is discussed. This paper presents flight- and ground-test evaluations of the propulsion system parameter-estimation process used by the performance seeking control system. The estimator consists of a compact propulsion system model and an extended Kalman filter. The extended Kalman filter estimates five engine component deviation parameters from measured inputs. The compact model uses measurements and Kalman-filter estimates as inputs to predict unmeasured propulsion parameters such as net propulsive force and fan stall margin. The ability to track trends and estimate absolute values of propulsion system parameters was demonstrated. For example, thrust stand results show a good correlation especially in trends between the performance seeking control estimated and measured thrust.

Orme, John S.↗

Subsonic flight test evaluation of a propulsion system parameter estimation process for the F100 engine

Integrated engine-airframe optimal control technology may significantly improve aircraft performance. This technology requires a reliable and accurate parameter estimator to predict unmeasured variables. To develop this technology base, NASA Dryden Flight Research Facility (Edwards, CA), McDonnell Aircraft Company (St. Louis, MO), and Pratt & Whitney (West Palm Beach, FL) have developed and flight-tested an adaptive performance seeking control system which optimizes the quasi-steady-state performance of the F-15 propulsion system. This paper presents flight and ground test evaluations of the propulsion system parameter estimation process used by the performance seeking control system. The estimator consists of a compact propulsion system model and an extended Kalman filter. The extended Laman filter estimates five engine component deviation parameters from measured inputs. The compact model uses measurements and Kalman-filter estimates as inputs to predict unmeasured propulsion parameters such as net propulsive force and fan stall margin. The ability to track trends and estimate absolute values of propulsion system parameters was demonstrated. For example, thrust stand results show a good correlation, especially in trends, between the performance seeking control estimated and measured thrust.

Orme, John S.↗

Observational Constraints on the Identification of Shallow Lunar Magmatism: Insights from Floor-Fractured Craters

Floor-fractured craters are a class of lunar crater hypothesized to form in response to the emplacement of a shallow magmatic intrusion beneath the crater floor. The emplacement of a shallow magmatic body should result in a positive Bouguer anomaly relative to unaltered complex craters, a signal which is observed for the average Bouguer anomaly interior to the crater walls. We observe the Bouguer anomaly of floor-fractured craters on an individual basis using the unfiltered Bouguer gravity solution from GRAIL and also a degree 100-600 band-filtered Bouguer gravity solution. The low-magnitude of anomalies arising from shallow magmatic intrusions makes identification using unfiltered Bouguer gravity solutions inconclusive. The observed anomalies in the degree 100-600 Bouguer gravity solution are spatially heterogeneous, although there is spatial correlation between volcanic surface morphologies and positive Bouguer anomalies. We interpret these observations to mean that the spatial heterogeneity observed in the Bouguer signal is the result of variable degrees of magmatic degassing within the intrusions.

Jozwiak, L. M.↗

Superluminous supernovae as standardizable candles and high-redshift distance probes

We investigate the use of type Ic superluminous supernovae (SLSN Ic) as standardizable candles and distance indicators. Their appeal as cosmological probes stems from their remarkable peak luminosities, hot blackbody temperatures, and bright rest-frame ultraviolet emission. We present a sample of 16 published SLSN, from redshifts 0.1 to 1.2, and calculate accurate K corrections to determine uniform magnitudes in 2 synthetic rest-frame filter bandpasses with central wavelengths at 400 nm and 520 nm. At 400 nm, we find an encouragingly low scatter in their uncorrected, raw mean magnitudes with M(400) = –21.86 ± 0.35 mag for the full sample of 16 objects. We investigate the correlation between their decline rates and peak magnitude and find that the brighter events appear to decline more slowly. In a manner similar to the Phillips relation for type Ia SNe (SNe Ia), we define a ΔM {sub 20} decline relation. This correlates peak magnitude and decline over 20 days and can reduce the scatter in standardized peak magnitudes to ±0.22 mag. We further show that M(400) appears to have a strong color dependence. Redder objects are fainter and also become redder faster. Using this peak magnitudecolor evolution relation, a surprisingly low scatter of between ±0.08 mag and ±0.13 mag can be found in peak magnitudes, depending on sample selection. However, we caution that only 8 to 10 objects currently have enough data to test this peak magnitudecolor evolution relation. We conclude that SLSN Ic are promising distance indicators in the high-redshift universe in regimes beyond those possible with SNe Ia. Although the empirical relationships are encouraging, the unknown progenitor systems, how they may evolve with redshift, and the uncertain explosion physics are of some concern. The two major measurement uncertainties are the limited numbers of low-redshift, well-studied objects available to test these relationships and internal dust extinction in the host galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗

Field testing of feedforward collective pitch control on the CART2 using a nacelle-based Lidar scanner

This work presents the results from a field test of LIDAR assisted collective pitch control using a scanning LIDAR device installed on the nacelle of a mid-scale research turbine. A nonlinear feedforward controller is extended by an adaptive filter to remove all uncorrelated frequencies of the wind speed measurement to avoid unnecessary control action. Positive effects on the rotor speed regulation as well as on tower, blade and shaft loads have been observed in the case that the previous measured correlation and timing between the wind preview and the turbine reaction are accomplish. The feedforward controller had negative impact, when the LIDAR measurement was disturbed by obstacles in front of the turbine. This work proves, that LIDAR is valuable tool for wind turbine control not only in simulations but also under real conditions. Moreover, the paper shows that further understanding of the relationship between the wind measurement and the turbine reaction is crucial to improve LIDAR assisted control of wind turbines.

17 WIND ENERGY↗

Accelerating full-waveform inversion using source stacking: synthetic experiments at the global scale in a realistic 3-D earth model

SUMMARY The spectral element method is currently the method of choice for computing accurate synthetic seismic wavefields in realistic 3-D earth models at the global scale. However, it requires significantly more computational time, compared to normal mode-based approximate methods. Source stacking, whereby multiple earthquake sources are aligned on their origin time and simultaneously triggered, can reduce the computational costs by several orders of magnitude. We present the results of synthetic tests performed on a realistic radially anisotropic 3-D model, slightly modified from model SEMUCB-WM1 with three component synthetic waveform ‘data’ for a duration of 10 000 s, and filtered at periods longer than 60 s, for a set of 273 events and 515 stations. We consider two definitions of the misfit function, one based on the stacked records at individual stations and another based on station-pair cross-correlations of the stacked records. The inverse step is performed using a Gauss–Newton approach where the gradient and Hessian are computed using normal mode perturbation theory. We investigate the retrieval of radially anisotropic long wavelength structure in the upper mantle in the depth range 100–800 km, after fixing the crust and uppermost mantle structure constrained by fundamental mode Love and Rayleigh wave dispersion data. The results show good performance using both definitions of the misfit function, even in the presence of realistic noise, with degraded amplitudes of lateral variations in the anisotropic parameter ξ. Interestingly, we show that we can retrieve the long wavelength structure in the upper mantle, when considering one or the other of three portions of the cross-correlation time series, corresponding to where we expect the energy from surface wave overtone, fundamental mode or a mixture of the two to be dominant, respectively. We also considered the issue of missing data, by randomly removing a successively larger proportion of the available synthetic data. We replace the missing data by synthetics computed in the current 3-D model using normal mode perturbation theory. The inversion results degrade with the proportion of missing data, especially for ξ, and we find that a data availability of 45 per cent or more leads to acceptable results. We also present a strategy for grouping events and stations to minimize the number of missing data in each group. This leads to an increased number of computations but can be significantly more efficient than conventional single-event-at-a-time inversion. We apply the grouping strategy to a real picking scenario, and show promising resolution capability despite the use of fewer waveforms and uneven ray path distribution. Source stacking approach can be used to rapidly obtain a starting 3-D model for more conventional full-waveform inversion at higher resolution, and to investigate assumptions made in the inversion, such as trade-offs between isotropic, anisotropic or anelastic structure, different model parametrizations or how crustal structure is accounted for.

Geochemistry & Geophysics↗

Cascaded analysis of signal and noise propagation through a heterogeneous breast model

Purpose: The detectability of lesions in radiographic images can be impaired by patterns caused by the surrounding anatomic structures. The presence of such patterns is often referred to as anatomic noise. Others have previously extended signal and noise propagation theory to include variable background structure as an additional noise term and used in simulations for analysis by human and ideal observers. Here, the analytic forms of the signal and noise transfer are derived to obtain an exact expression for any input random distribution and the ''power law'' filter used to generate the texture of the tissue distribution. Methods: A cascaded analysis of propagation through a heterogeneous model is derived for x-ray projection through simulated heterogeneous backgrounds. This is achieved by considering transmission through the breast as a correlated amplification point process. The analytic forms of the cascaded analysis were compared to monoenergetic Monte Carlo simulations of x-ray propagation through power law structured backgrounds. Results: As expected, it was found that although the quantum noise power component scales linearly with the x-ray signal, the anatomic noise will scale with the square of the x-ray signal. There was a good agreement between results obtained using analytic expressions for the noise power and those from Monte Carlo simulations for different background textures, random input functions, and x-ray fluence. Conclusions: Analytic equations for the signal and noise properties of heterogeneous backgrounds were derived. These may be used in direct analysis or as a tool to validate simulations in evaluating detectability.

60 APPLIED LIFE SCIENCES↗

Evaluation of a Surface Spill Operation to Return Adult Steelhead Overshoots Downstream of McNary Dam

This study, funded by the U.S. Army Corps of Engineers (USACE), was conducted by the Pacific Northwest National Laboratory to evaluate the efficacy of operating one Top Spill Weir (TSW) at McNary Dam outside the normal TSW operation dates for juvenile salmon passage. Of interest is whether the TSW is an effective downstream passage route for adult steelhead overshoots. Overshoots are fish which, having passed upstream at McNary Dam, must pass downstream to return to their natal stream to spawn. This report covers Fall (2019) and Spring (2020) study periods. The study design arranged the available 24 hours of TSW spill per week into weekly blocks with sub-blocks differentiated into day and night operations with TSW discharge periods of 4- and 8-hours duration. Hydroacoustic techniques were used to sample adult fish passage at the TSW and at turbine units 1 and 10. The experimental design contrasted TSW spill periods of differing duration and at different times of the day. The small number of fish detected passing the TSW, and the smaller number of fish detected passing the turbine units, were best suited to an ad hoc, exploratory approach to evaluating the effect of TSW spill. It is worthwhile to note that the operations data obtained for the fall study period had a greater than expected number of gaps and apparent anomalies that we believe were a result of how the data were aggregated. These problems are not particularly problematic for the present study, because the available data still provide a good indication of whether the TSW was operating at each point in time. TSW flows in both fall and spring data sets were able to be cleaned up using the established relationship between forebay elevation and TSW discharge rate. Additional cleanup of operations data would be needed, however, if more quantitative evaluation of dam-wide flow and passage relationships were needed. This study contrasted TSW spill periods of differing duration and at different times of the day. The small number of fish detected passing the TSW, and the smaller number of fish detected passing the turbine units were best suited to an ad hoc, exploratory approach to evaluating the effect of TSW spill. Spring adult steelhead passage numbers estimated using hydroacoustics were notably lower than during the fall study period, and that was consistent with our analysis of PIT tagged fish likely to be in the vicinity during each study period. Detections of fish in BlueView sampling areas upstream of the TSW and powerhouse were not correlated with detections of fish passing hydroacoustic sampling areas, which suggests that fish approaching the face of the dam can move around the forebay before passing. Other fish detected in the forebay in large numbers, such as shad, were able to be filtered out of steelhead passage counts and did not appear to be influencing hydroacoustic passage rate estimates. A pulse of passage at the initial TSW opening was weakly evident, but trends across 4- and 8-hour operational periods did not show a distinct decline in passage over time as TSW operation continued. Our findings do not indicate a reason to choose one 8-hour period over two 4-hour periods, or vice versa. This suggests that the duration of spill periods can be chosen based on operational or other considerations. Passage rates were consistently higher during the daytime TSW discharge periods, relative to nighttime TSW discharge periods. The experimental design of the current study used start times near dawn for day periods and near dusk for night periods.

59 BASIC BIOLOGICAL SCIENCES↗