Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Performance of inlet stage of transonic compressor

The overall and blade-element performances are presented over the stable flow operating range of the stage at the design tip speed of 426 m/sec. Stage peak efficiency of 0.83 was obtained at a weight flow of 28.8 kg/sec and a pressure ratio of 1.52. The stall margin for the stage was 8 percent based on weight flow and pressure ratio at peak efficiency and stall. The rotor appears to be stalling prematurely as evidenced by high rotor tip losses.

Urasek, D. C.↗
NASA NTRS1980

Rotor redesign for a highly loaded 1800 ft/sec tip speed fan, 2

Tests were conducted on a 0.5 hub/tip ratio single-stage fan designed to produce a pressure ratio of 2.280 at an efficiency of 83.8 percent with a rotor tip speed of 548.6 m/sec (1800 ft/sec). The rotor was designed utilizing a quasi three dimensional design system and four-part, multiple-circular-arc airfoil sections. The rotor is the third in a series of single-stage fans that have included a precompression airfoil design and a multiple-circular-arc airfoil design. The stage achieved a peak efficiency of 82.8 percent after performance had deteriorated by 0.6 of a point. The design mass flow was achieved at the peak efficiency point, and the stage total pressure ratio was 2.20, which is lower than the design goal of 2.28. The surge margin of 13% from the peak efficiency point exceeded the design goal of 7%.

Bolt, C. R.↗
DOE OSTI2016

Optimization design of helium circulator diffuser in HTR-PM - 18488

Circulator is very important in HTR-PM. It needs to supply enough pressure rise to circulate cooled helium in the primary loop of HTR-PM to bring heat out. Its pressure rise requirement is the highest among the worldwide circulators. Diffuser is one main component to produce pressure rise for circulator. And the most particular for HTR-PM is that the helium must flow out from two round tubes after flowing through the diffuser, which is very different from other circulators. This special export structure increases flow loss and decreases diffuser efficiency. So it is necessary to optimize diffuser to satisfy high pressure rise requirement of HTR-PM circulator with the special export structure. Four geometrical variables of diffuser have been studied and optimized. Based on the flow and performance analysis, the optimum structure was chosen. Then the detailed simulation was done by combining it with impeller to obtain performance characteristics of the whole circulator. Finally, the simulation results were compared with experimental results. It was obtained that simulation pressure rise was 201 kPa and experimental result was 210 kPa, which verified that optimization design of diffuser was effective. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1950

Investigation of Performance of Axial-Flow Compressor of XT-46 Turbine-Propeller Engine. I - Preliminary Investigation at 50-,70-, and 100-Percent Design Equivalent Speed

An investigation is being conducted to determine the performance of the 12-stage axial-flow compressor of the XT-46 turbine-propeller engine. This compressor was designed to produce a pressure ratio of 9 at an adiabatic efficiency of 0.86. The design pressure ratios per stage were considerably greater than any employed in current aircraft gas-turbine engines using this type of compressor. The compressor performance was evaluated at two stations. The station near the entrance section of the combustors indicated a peak pressure ratio of 6.3 at an adiabatic efficiency of 0.63 for a corrected weight flow of 23.1 pounds per second. The other, located one blade-chord downstream of the last stator row, indicated a peak pressure ratio of 6.97 at an adiabatic efficiency of 0.81 for a corrected weight flow of 30.4 pounds per second. The difference in performance obtained at the two stations is attributed to shock waves in the vicinity of the last stator row. These shock waves and the accompanying flow choking, together with interstage circulatory flows, shift the compressor operating curves into the region where surge would normally occur. The inability of the compressor to meet design pressure ratio is probably due to boundary-layer buildup in the last stages, which cause axial velocities greater than design values that, in turn, adversely affect the angles of attack and turning angles in these blade rows.

John W R Creagh↗
DOE OSTI2021

Inertially enhanced mass transport using 3D-printed porous flow-through electrodes with periodic lattice structures

Significance The efficient utilization of electrical energy is an increasingly important challenge, especially as renewable energy sources become cheaper and demand increases. Electrochemical reactors utilizing flow-through electrodes (FTEs) provide an attractive path toward the efficient utilization of electrical energy. Their commercial viability and ultimate adoption hinge on attaining high current densities to drive cost competitiveness. There are limited opportunities for engineering FTE materials, as these are often random, disordered media. Alternatively, three-dimensional (3D)–printed FTEs provide the opportunity to quickly explore the impact of engineered electrode architectures on device performance. We demonstrate that 3D-printed FTEs have the potential to exceed the performance of conventional materials by using the expanded design freedom to engineer the internal flow.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2019

System and method for using engine efficiency in predictive maintenance of a power generator

Methods, systems and apparatuses for early fault detection of a power generator are provided. An alternator output power parameter is received and a fuel flow input measurement is received. An estimated engine efficiency value is determined in response to the alternator output power parameter and the fuel flow input measurement. The estimated engine efficiency value may be transmitted to a monitoring device.

Kallhoff, Dustin Wayne↗
NASA NTRS1987

On a finite element CFD algorithm for compressible, viscous and turbulent aerodynamic flows

This paper develops and analyses individual construction aspects of an efficient and accurate finite element algorithm for prediction of viscous and turbulent flow fields of impact in aerodynamics. The theoretical construction employs a Taylor weak statement (TWS) for coincident embedding of stability mechanisms within a classic Galerkin finite element formulation of semidiscrete approximation error orthogonalization. A wide variety of the stabilizing mechanisms of independently derived CFD algorithms are contained within the TWS theory. An implicit construction that meets the requirement of efficient convergence to steady state is developed. The theoretical asymptotic error estimates of the TWS finite element algorithm for supersonic and viscous boundary layer flows are verified. Application to a three-dimensional turbulent flow is cited.

Baker, A. J.↗
DOE OSTI2018

ICRF mode conversion in three-ion species heating experiment and in flow drive experiment on the Alcator C-Mod tokamak

In recent three-ion species (majority D and H plus a trace level of 3He) ICRF heating experiments on Alcator C-Mod, double mode conversion on both sides of the 3He cyclotron resonance has been observed using the phase contrast imaging (PCI) system. The MC locations are used to estimate the species concentrations in the plasma. Simulation using TORIC shows that with the 3He level <1%, most RF power is absorbed by the 3He ions and the process can generate energetic 3He ions. In mode conversion (MC) flow drive experiment in D(3He) plasma at 8 T, MC waves were also monitored by PCI. The MC ion cyclotron wave (ICW) amplitude and wavenumber kR have been found to correlate with the flow drive force. The MC efficiency, wave-number k of the MC ICW and their dependence on plasma parameters like Te0 have been studied. Based on the experimental observation and numerical study of the dispersion solutions, a hypothesis of the flow drive mechanism has been proposed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1992

Grid generation and its application to separated flows

A method for the computation of recirculating flows on a nonorthogonal boundary-fitted coordinate system is presented. The algebraic grid generation technique is used to generate grids in a flow field of arbitrary shape. Computations are performed by using the set of governing equations transformed for use on a generalized curvilinear coordinate system. Turbulent flow computations were made by using the k-epsilon model for most of the flow cases. Three pressure correction algorithms - SIMPLE, SIMPLEC, and PISO - were incorporated for use on a nonorthogonal grid. Comparisons were made on the basis of numerical stability and accuracy. The present method was found to be efficient for computations of recirculating flows.

Maruszewski, J. P.↗
NASA NTRS2001

A Parallel Multigrid Solver for Viscous Flows on Anisotropic Structured Grids

This paper presents an efficient parallel multigrid solver for speeding up the computation of a 3-D model that treats the flow of a viscous fluid over a flat plate. The main interest of this simulation lies in exhibiting some basic difficulties that prevent optimal multigrid efficiencies from being achieved. As the computing platform, we have used Coral, a Beowulf-class system based on Intel Pentium processors and equipped with GigaNet cLAN and switched Fast Ethernet networks. Our study not only examines the scalability of the solver but also includes a performance evaluation of Coral where the investigated solver has been used to compare several of its design choices, namely, the interconnection network (GigaNet versus switched Fast-Ethernet) and the node configuration (dual nodes versus single nodes). As a reference, the performance results have been compared with those obtained with the NAS-MG benchmark.

Prieto, Manuel↗
DOE OSTI2024

Computationally efficient and error aware surrogate construction for numerical solutions of subsurface flow through porous media

Limiting the injection rate to restrict the pressure below a threshold at a critical location can be an important goal of simulations that model the subsurface pressure between injection and extraction wells. The pressure is approximated by the solution of Darcy’s partial differential equation for a given permeability field. The subsurface permeability is modeled as a random field since it is known only up to statistical properties. This induces uncertainty in the computed pressure. Solving the partial differential equation for an ensemble of random permeability simulations enables estimating a probability distribution for the pressure at the critical location. These simulations are computationally expensive, and practitioners often need rapid online guidance for real-time pressure management. An ensemble of numerical partial differential equation solutions is used to construct a Gaussian process regression model that can quickly predict the pressure at the critical location as a function of the extraction rate and permeability realization. The Gaussian process surrogate analyzes the ensemble of numerical pressure solutions at the critical location as noisy observations of the true pressure solution, enabling robust inference using the conditional Gaussian process distribution. Our first novel contribution is to identify a sampling methodology for the random environment and matching kernel technology for which fitting the Gaussian process regression model scales as O ( n log n ) instead of the typical O ( n 3 ) rate in the number of samples n used to fit the surrogate. The surrogate model allows almost instantaneous predictions for the pressure at the critical location as a function of the extraction rate and permeability realization. Our second contribution is a novel algorithm to calibrate the uncertainty in the surrogate model to the discrepancy between the true pressure solution of Darcy’s equation and the numerical solution. Finally, although our method is derived for building a surrogate for the solution of Darcy’s equation with a random permeability field, the framework broadly applies to solutions of other partial differential equations with random coefficients.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

A continuum model for heat and mass transfer in moving-bed reactors for thermochemical energy storage

In this work, a continuum heat and mass transfer model coupling transport phenomena and high-temperature thermochemical reactions is developed for stationary packed-bed and counter-flow moving-bed reactors. After presenting the general modeling framework, we focus on the 2D axisymmetric version of the model for which validation is conducted with experimental results for a packed-bed reactor in the literature for manganese-iron oxide reduction/oxidation and an in-house counter-flow moving-bed reactor for magnesium-manganese oxide reduction up to 1450 °C. Transient simulation results including the local distributions of gas/solid temperatures, oxygen concentration and the extent of reaction, as well as the various energy flow components and energy conversion efficiencies are reported. The results based on the 2D axisymmetric model are also compared with those obtained from a previous 1D model. The comparison shows that capturing the radial variation is critical in reactor modeling and the 2D results demonstrate improved agreement with experiments. Specifically, large temperature variations along the radial direction are observed especially in the reaction zone; this non-uniform radial temperature distribution has a significant effect on the chemical reaction extent due to its strong dependence on temperature; and the overall oxygen concentration at the reactor exit and the predicted system efficiency are slightly lower in the 2D model compared to the 1D model. Finally, the present heat and mass transfer model can provide valuable insights into reactor design, scale-up, and operating conditions selection to maximize system energy storage efficiency.

25 ENERGY STORAGE↗
NASA NTRS1974

Design and performance of a high-pressure-ratio, highly loaded axial-flow transonic compressor space

A 50-cm-diam. axial-flow transonic compressor stage with multiple-circular-arc blades was designed and tested. At design speed, a rotor peak efficiency of 0.85 occurred at an equivalent weight flow of 29.3 kg/sec. Stage peak efficiency was 0.79 at 28.6 kg/sec. Stage total pressure ratio at peak efficiency was 1.84. The stall margin at design speed was 5 percent. Rotor and stator losses were higher than predicted. The stator choked at design flow.

Lewis, G. W., Jr.↗
NASA NTRS1991

Relative efficiency and accuracy of two Navier-Stokes codes for simulating attached transonic flow over wings

Two codes which solve the 3-D Thin Layer Navier-Stokes (TLNS) equations are used to compute the steady state flow for two test cases representing typical finite wings at transonic conditions. Several grids of C-O topology and varying point densities are used to determine the effects of grid refinement. After a description of each code and test case, standards for determining code efficiency and accuracy are defined and applied to determine the relative performance of the two codes in predicting turbulent transonic wing flows. Comparisons of computed surface pressure distributions with experimental data are made.

Bonhaus, Daryl L.↗
DOE OSTI2022

A particle resolved simulation approach for studying shock interactions with moving, colliding solid particles

This work applies a new combination of techniques for the fully resolved simulation of compressible, gas–particle multiphase flows. Here, the adaptive wavelet collocation method is used to dynamically, and efficiently, adapt the computational grid to localized flow features and the particles. A characteristic-based volume penalization method that imposes arbitrary Dirichlet, Neumann, or Robin-type immersed boundary conditions, is used to enforce the no-slip condition at particle surfaces. A hard-sphere collision model is applied to capture the particle–particle collisions. Proof of concept test cases are presented, showcasing the dynamic grid adaptation and fully resolved two-way coupling between the phases that is possible with this approach. Results for a shock-driven single cylinder under viscous and inviscid conditions are presented along with a demonstration of a shock interacting with a cloud of randomly distributed cylinders and spheres.

42 ENGINEERING↗
NASA NTRS1986

Heat transfer in the tip region of a rotor blade simulator

In gas turbines, the blades of axial turbine stages rotate in close proximity to a stationary peripheral wall. Differential expansion of the turbine wheel, blades, and the shroud causes variations in the size of the clearance gap between blade tip and stationary shroud. The necessity to tolerate this differential thermal expansion dictates that the clearance gap cannot be eliminated altogether, despite accurate engine machining. Pressure differences between the pressure and suction sides of a blade drives a flow through the clearance gap. This flow, the tip leakage flow, is detrimental to engine performance. The primary detrimental effect of tip leakage flow is the reduction of turbine stage efficiency, and a second is the convective heat transfer associated with the flow. The surface area at the blade tip in contact with the hot working gas represents an additional thermal loading on the blade which, together with heat transfer to the suction and pressure side surface area, must be removed by the blade internal cooling flows. Experimental results concerned with the local heat transfer characteristics on all surfaces of shrouded, rectangular cavities are reported. A brief discussion of the mass transfer system used is given.

Chyu, M. K.↗