Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow pattern”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Spectrophotometric Modeling and Mapping of (101955) Bennu

Using hyperspectral data collected by OVIRS, the visible and infrared spectrometer onboard the OSIRIS-REx (Origins, Spectral Interpretation, Resource Identification, and Security–Regolith Explorer) spacecraft, we modeled the global average spectrophotometric properties of the carbonaceous asteroid (101955) Bennu and mapped their variations. We restricted our analysis to 0.4–2.5 µm to avoid the wavelengths where thermal emission from the asteroid dominates (>2.5 µm). Bennu has global photometric properties typical of dark asteroids; we found a geometric albedo of 0.046 ± 0.007 and a linear phase slope of 0.024 ± 0.007 mag deg–1 at 0.55 µm. The average spectral slope of Bennu’s normal albedo is –0.0030 µm–1, and the phase reddening parameter is 4.3´10–4 µm–1 deg–1, both over the spectral range of 0.5–2.0 µm. We produced normal albedo maps and phase slope maps at all spectral channels, from which we derived spectral slope and phase reddening maps. Correlation analysis suggests that phase slope variations on Bennu are likely due to photometric roughness variation. A correlation between photometric roughness and thermal roughness is evident, implying that the roughness of Bennu is self-similar on scales from tens of microns to meters. Our analysis reveals latitudinal trends in the spectral color slope and phase reddening on Bennu. The equatorial region appears to be redder than the global average, and the spectral slope decreases towards higher latitudes. Phase reddening on Bennu is relatively weak in the equatorial region and shows an asymmetry between the northern and southern hemispheres. We attributed the latitudinal trend to the geophysical conditions on Bennu that result in a global pattern of mass flow towards the equator.

Jian-Yang Li (李荐扬)↗

PAAV Concept Document

The Pathfinding for Airspace with Autonomous Vehicles (PAAV) Concept Document, version 1.0, lays out the key challenges and potential solutions for the use of uncrewed aircraft (UA) technology for future regional air cargo operations. The challenges and solutions described in this document were informed by communications with the UA industry community (e.g., RTCA, the Federal Aviation Administration, and regional air cargo business operators), as well as the PAAV team’s research activities during the last two years including four tabletop exercises, a human-in-the-loop simulation study, a numerical simulation study, a functional allocation study, and flight data analysis (Appendix A). This document first describes the expected operational context of PAAV (Section 2), such as the flight mission, baseline UAS components, nominal operations, m:N operations (i.e., "m" remote pilots per "N" aircraft), and off-nominal operations. This context sets the scope for the PAAV concept development work. PAAV concept development assumes that UA operations will be increasingly autonomous. Thus, near- and far-term assumptions are defined (Section 3). PAAV identified seven key challenges for UA operations (Section 4): - Flight route planning - Separation and flow management - Traffic pattern integration - Contingency management - Taxi, takeoff, and landing - m:N operations - Communications operations The following 13 potential solutions to these challenges are then described (Section 5): - Scalable communications architecture - Data link - Designated UAS corridors - Crew planning for m:N operations - Flight route optimization - Traffic load-level control - Trajectory solutions with data link - Automated hazard avoidance for m:N operations - Traffic pattern integration (TPI) tool - Standard lost command and control (C2) link (LC2L) procedures - Automated hazard avoidance under LC2L - Auto-taxi, auto-takeoff, and auto-land - Ground control station (GCS) user interface for m:N operations The document attempts to link each of these solutions to one or more of the challenge areas. Novel solutions involving numerous automation technologies are needed to mitigate traffic and airspace management challenges, especially for realizing m:N operations and ensuring safety under LC2L conditions. The purpose of this document is to help understand alternatives and tradeoffs among potential solutions and provide a foundation for a cohesive PAAV concept that will be described and refined in subsequent concept versions.

Unmanned aircraft, uncrewed aircraft, regional air↗

Theory of discrete vortex noise

A solution is obtained for the noise induced by vortex shedding from the trailing edge of a semiinfinite flat plate. The method of solution for the potential flow is based on a procedure whereby an inner incompressible flow is matched to an outer acoustic field. Acoustic wave fronts are calculated and compared qualitatively with schlieren photographs of similar flows. The acoustic directivity pattern is obtained, and the extreme sensitivity of this parameter to the incompressible flow near the trailing edge of the plate is investigated.

Davis, S. S.↗

Numerical investigation of unsteady flow development in a nozzle-duct configuration

A computational approach has been used to resolve the transient phenomena caused by a rocket engine starting up and exhausting into a short duct. The results are obtained from the finite-difference Navier-Stokes, continuity, and energy equations for a single component gas. Using a recently developed numerical technique to account for the time-varying boundary conditions at the nozzle throat and the duct openings, the numerical simulation of the idealized ignition flow model has yielded some insight into the complex interactions between the wave patterns and the vortical flow. The present findings verify the hypothesis that a lateral expansion of the jetstream outside the nozzle will generate an over-pressure pulse on the duct wall if the jetstream is restricted within the nozzle by flow separation. The numerical simulations of this complex flow problem should be useful for improving simple correlation techniques used for engineering purposes.

Li, C. P.↗

A qualitative view of cryogenic fluid injection into high speed flows

The injection of supercritical pressure, subcritical temperature fluids, into a 2-D, ambient, static temperature and static pressure supersonic tunnel and free jet supersonic nitrogen flow field was observed. Observed patterns with fluid air were the same as those observed for fluid nitrogen injected into the tunnel at 90 deg to the supersonic flow. The nominal injection pressure was of 6.9 MPa and tunnel Mach number was 2.7. When injected directly into and opposing the tunnel exhaust flow, the observed patterns with fluid air were similar to those observed for fluid nitrogen but appeared more diffusive. Cryogenic injection creates a high density region within the bow shock wake but the standoff distance remains unchanged from the gaseous value. However, as the temperature reaches a critical value, the shock faded and advanced into the supersonic stream. For both fluids, nitrogen and air, the phenomena was completely reversible.

Hendricks, R. C.↗

Crustal deformation, the earthquake cycle, and models of viscoelastic flow in the asthenosphere

The crustal deformation patterns associated with the earthquake cycle can depend strongly on the rheological properties of subcrustal material. Substantial deviations from the simple patterns for a uniformly elastic earth are expected when viscoelastic flow of subcrustal material is considered. The detailed description of the deformation pattern and in particular the surface displacements, displacement rates, strains, and strain rates depend on the structure and geometry of the material near the seismogenic zone. The origin of some of these differences are resolved by analyzing several different linear viscoelastic models with a common finite element computational technique. The models involve strike-slip faulting and include a thin channel asthenosphere model, a model with a varying thickness lithosphere, and a model with a viscoelastic inclusion below the brittle slip plane. The calculations reveal that the surface deformation pattern is most sensitive to the rheology of the material that lies below the slip plane in a volume whose extent is a few times the fault depth. If this material is viscoelastic, the surface deformation pattern resembles that of an elastic layer lying over a viscoelastic half-space. When the thickness or breath of the viscoelastic material is less than a few times the fault depth, then the surface deformation pattern is altered and geodetic measurements are potentially useful for studying the details of subsurface geometry and structure. Distinguishing among the various models is best accomplished by making geodetic measurements not only near the fault but out to distances equal to several times the fault depth. This is where the model differences are greatest; these differences will be most readily detected shortly after an earthquake when viscoelastic effects are most pronounced.

Cohen, S. C.↗

Crustal deformation, the earthquake cycle, and models of viscoelastic flow in the asthenosphere

The crustal deformation patterns associated with the earthquake cycle can depend strongly on the rheological properties of subcrustal material. Substantial deviations from the simple patterns for a uniformly elastic earth are expected when viscoelastic flow of subcrustal material is considered. The detailed description of the deformation pattern and in particular the surface displacements, displacement rates, strains, and strain rates depend on the structure and geometry of the material near the seismogenic zone. The origin of some of these differences are resolved by analyzing several different linear viscoelastic models with a common finite element computational technique. The models involve strike-slip faulting and include a thin channel asthenosphere model, a model with a varying thickness lithosphere, and a model with a viscoelastic inclusion below the brittle slip plane. The calculations reveal that the surface deformation pattern is most sensitive to the rheology of the material that lies below the slip plane in a volume whose extent is a few times the fault depth. If this material is viscoelastic, the surface deformation pattern resembles that of an elastic layer lying over a viscoelastic half-space. When the thickness or breath of the viscoelastic material is less than a few times the fault depth, then the surface deformation pattern is altered and geodetic measurements are potentially useful for studying the details of subsurface geometry and structure. Distinguishing among the various models is best accomplished by making geodetic measurements not only near the fault but out to distances equal to several times the fault depth. This is where the model differences are greatest; these differences will be most readily detected shortly after an earthquake when viscoelastic effects are most pronounced.

Cohen, S. C.↗

Performance of jet- and inner-ring-lubricated 35 millimeter bore ball bearings operating to 2.5 million DN

Parametric tests were conducted with a 35 millimeter bore, angular contact ball bearing having a single outer land guided cage. Lubrication was achieved by flowing oil through axial grooves and radial holes machined in the inner ring of the bearing. Test conditions were a thrust load of 667 N (150 lb), shaft speeds from 48,000 to 72,000 rpm, and an oil inlet temperature of 394 K (250 F). Data from tests where the distribution of the total oil supplied to the inner ring was 50 percent for bearing lubrication and 50 percent for bearing inner ring cooling were compared with those where the distribution pattern was 25 percent lubrication and 75 percent cooling. Successful operation was experienced with both the 50-50 and 25-75 percent flow distribution patterns to 2.5 million DN. The 50-50 percent flow pattern provided the cooler bearing operation of the two inner ring lubricated bearings. The jet lubricated bearing had lower outer ring and higher inner ring temperatures than the inner ring lubricated bearings. Maximum power loss of 2.8 kW (3.7 hp) was experienced with the 25-75 percent flow distribution, and maximum percent cage slip of 7.0 occurred at 72,300 rpm with the 50-50 percent flow distribution.

Schuller, F., T.↗

Measurements of noise produced by flow past lifting surfaces

Wind tunnel studies have been conducted to determine the specific locations of aerodynamic noise production within the flow field about various lifting-surface configurations. The models tested included low aspect ratio shapes intended to represent aircraft flaps, a finite aspect ratio NACA 0012 wing, and a multi-element wing section consisting of a main section, a leading edge flap, and dual trailing edge flaps. Turbulence was induced on the models by surface roughness. Lift and drag were measured for the flap models. Hot-wire anemometry was used for study of the flap-model vortex roll-up. Apparent noise source distributions were measured by use of a directional microphone system, located outside the tunnel, which was scanned about the flow region to be analyzed under computer control. These distributions exhibited a diversity of pattern, suggesting that several flow processes are important to lifting-surface noise production. Speculation concerning these processes is offered.

Kendall, J. M.↗

Heat flow in eastern Egypt - The thermal signature of a continental breakup

It is noted that the Red Sea is a modern example of continental fragmentation and incipient ocean formation. A consistent pattern of high heat flow in the Red Sea margins and coastal zone, including Precambrian terrane up to at least 30 km from the Red Sea, has emerged from the existing data. It is noted that this pattern has important implications for the mode and mechanism of Red Sea opening. High heat flow in the Red Sea shelf requires either a high extension of the crust in this zone (probably with major basic magmatic activity) or young oceanic crust beneath this zone. High heat flow in the coastal thermal anomaly zone may be caused by lateral conduction from the offshore lithosphere and/or from high mantle heat flow. It is suggested that new oceanic crust and highly extended continental crust would be essentially indistinguishable with the available data in the Red Sea margins, and are for many purposes essentially identical.

Morgan, P.↗

A new determination of the solar rotation rate

We use 'stackplot' displays to compare observations of the photospheric magnetic field during sunspot cycle 21 with simulations based on the flux-transport model. Adopting nominal rates of diffusion, differential rotation, and meridional flow, we obtain slanted patterns similar to those of the observed field, even when the sources of flux are assigned random longitudes in the model. At low latitudes, the slopes of the nearly vertical patterns of simulated field are sensitive to the rotation rate used in the calculation, and insensitive to the rates of diffusion and flow during much of the sunspot cycle. Good agreement between the observed and simulated patterns requires a synodic equatorial rotation period of 26.75 +/- 0.05 days.

Sheeley, N. R., Jr.↗

Modal propagation angles in a cylindrical duct with flow and their relation to sound radiation

The main emphasis is upon the propagation angle with respect to the duct axis and its relation to the far-field acoustic radiation pattern. When the steady flow Mach number is accounted for in the duct, the propagation angle in the duct is shown to be coincident with the angle of the principal lobe of far-field radiation obtained using the Wiener-Hopf technique. Different Mach numbers are allowed within the duct and in the external field. For static tests with a steady flow in an inlet but with no external Mach number the far-field radiation pattern is shifted considerably toward the inlet axis when compared to zero Mach number radiation theory. As the external Mach number is increased the noise radiation pattern is shifted away from the inlet axis. The theory is developed using approximations for sound propagation in circular ducts. An exact analysis using Hankel function solutions for the zero Mach number case is given to provide a check of the simpler approximate theory.

Rice, E. J.↗

Turbulent Fluid Motion 6: Turbulence, Nonlinear Dynamics, and Deterministic Chaos

Several turbulent and nonturbulent solutions of the Navier-Stokes equations are obtained. The unaveraged equations are used numerically in conjunction with tools and concepts from nonlinear dynamics, including time series, phase portraits, Poincare sections, Liapunov exponents, power spectra, and strange attractors. Initially neighboring solutions for a low-Reynolds-number fully developed turbulence are compared. The turbulence is sustained by a nonrandom time-independent external force. The solutions, on the average, separate exponentially with time, having a positive Liapunov exponent. Thus, the turbulence is characterized as chaotic. In a search for solutions which contrast with the turbulent ones, the Reynolds number (or strength of the forcing) is reduced. Several qualitatively different flows are noted. These are, respectively, fully chaotic, complex periodic, weakly chaotic, simple periodic, and fixed-point. Of these, we classify only the fully chaotic flows as turbulent. Those flows have both a positive Liapunov exponent and Poincare sections without pattern. By contrast, the weakly chaotic flows, although having positive Liapunov exponents, have some pattern in their Poincare sections. The fixed-point and periodic flows are nonturbulent, since turbulence, as generally understood, is both time-dependent and aperiodic.

Deissler, Robert G.↗

The vortex flap F-106B, overcoming safety and data problems in flight testing

A NASA, F-106B airplane equipped with a vortex flap is establishing a data base for calibration of design and analysis tools for this vortical flow control concept. Some of the problems in safely and precisely flying to research data points were caused by the modified airplane's low longitudinal stability and low margin of structural strength. These characteristics are, in part, a consequence of the program's low cost approach which utilizes a bolt-on, ground-adjustable flap attached to a minimally modified airplane. Presently, the 40-degree flap deflection flight research is being concluded with a flow visualization phase. A similar pattern of flight envelope expansion, pressure distribution, performance, and flow visualization phases remain to be accomplished for the 30-degree flap setting. To date, good research flight data has followed resolution of the safety and data problems described.

Brown, Philip W.↗

Acoustic scattering from locally homogeneous turbulence

An equation is derived for acoustic scattering from the velocity and temperature fields of a drifting blob of air turbulence. The equation is solved for scattering from the mean and turbulent portions of both fields, and the time autocorrelation and power spectral density of the received signal are calculated. The mean velocity and temperature fields, as well as the corresponding turbulence intensity distributions, are allowed to be spatially nonuniform. The turbulent fields are required to be only locally homogeneous and locally stationary. It is shown that the common practice of representing antenna patterns by either truncating the flow or tapering the strength of the flow is, at least in the case of the transmitting pattern, not a bad approximation. Spectral broadening of the receiver signal due to convection of the small scattering eddies by macroeddies and by the mean flow in modeled, and the broadening by macroeddy convection is seen to render negligible the broadening which arises from the drift of the target flow through the antenna beam. The analysis reveals that only for target flows having a high degree of spatial uniformity and/or symmetry does the received positive-frequency power spectral density turn out to be symmetrical about a center frequency.

Ramsey, V. W.↗

Sound measurements within and in the radiated field of an annular duct with flow.

Recent theory on sound propagation for flow ducts initiated a research program (sponsored by NASA-Langley, Contract NAS1-10472) which has the objective of comparing detailed acoustical measurements with the analytical predictions for sound propagation in a duct with sheared flow. The effects considered experimentally mean flow, shear, wall impedance, and source distribution on sound propagation within and radiation from finite lenght annular ducts. Results reported here are confined to acoustic distribution in hard annular ducts with and without mean flow and radiated field patterns for the same conditions. The acoustic distributions are shown for single and multi-mode excitation. The flow duct facility is also described.

Plumblee, H. E.↗

Thermal Infrared Observations of Lava Flows During the 1984 Mauna Loa Eruption

Thermal infrared videotape images of the flowing lava streams and the vent areas at 10.6 microns were made, as well as some broadband images in the 8 to 12 micron range (for gas plume detection). These data were calibrated with on-site hand-held radiometer measurements, in-flow thermocouple measurements, and with later laboratory kiln measurements. Infrared video data are useful in quantitatively assessing the pattern and mode of flow thermal losses, particularly with regard to radiative losses from established/incipient floating crust. The general cooling of the flows downstream was readily apparent. Upper reaches of the active flow exhibited nearly crust-free main channels, radiating at about 700 to 800 degrees C. Below about the 7500 foot level (about 8 km from the vent) the flows formed nearly continuous crust and tended to spread, become less well-defined and founder due to a reduction in slope. Nevertheless, in thermal IR observations, the surface trace of the active subsurface channel was visible, radiating at about 500 to 700 degrees C. At the active flow front, most solid crust radiated at temperatures less than 500 to 600 degrees C, however bright high temperature interiors (approximately 900 to 1000 degrees C) were clearly visible though evolving fissures.

Pieri, D. C.↗