Search NASA⌕ Search

SEARCH · Search NASA

Results for “model structural error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Capella: Structure and Abundances

This grant covers the analysis of ASCA spectra of the cool star binary system Capella. This project has also required the analysis of simultaneous EUVE data. The ASCA spectrum of Capella could not be fit with standard models; by imposing models based on strong lines observed with EUVE, a problem wavelength region was identified. Correcting the problem required calculations of atomic collision strengths of higher principal quantum number than had ever been calculated, resulting in a paper in process by Liedahl and Brickhouse. With these new models applied to the ASCA spectrum, better fits were obtained. While solar abundance ratios are generally consistent with the ASCA data, the ratio of Ne/Fe is three to four times lower than solar photospheric values. Whether there is a general First Ionization Potential (FIP) effect or a specific neon anomaly cannot be determined from these data. Detailed discussion has been provided to NASA in the most recent annual report (1997). Two poster presentations have been made regarding modeling requirements. A substantial paper is in the final revision form, following review by six co-authors. The results of this work have wide implications, since the newly calculated emission lines almost certainly contribute to other problems in fitting not only other stellar spectra, but also composite supernova remnants, galaxies, and cooling flow clusters of galaxies. Furthermore, Liedahl and Brickhouse have identified other species for which lines of a similar nature (high principal quantum number) will contribute significant flux. For moderate resolution X-ray spectra, lines left out of the models in relatively isolated bands, will be attributed to continuum flux by spectral fitting engines, causing errors in line-to-continuum ratios. Thus addressing the general theoretical problem is of crucial importance.

Brickhouse, Nancy S.↗

Detailed Studies on the Structure and Dynamics of Reacting Dusty Flows at Normal and Microgravity

Dusty reacting flows are of particular interest for a wide range of applications. Inert particles can alter the flammability and extinction limits of a combustible mixture. Reacting particles can release substantial amount of heat and can be used either for power generation or propulsion. Accumulation of combustible particles in air can result in explosions which, for example, can occur in grain elevators, during lumber milling and in mine galleries. Furthermore, inert particles are used as flow velocity markers in reacting flows, and their velocity is measured by non-intrusive laser diagnostic techniques. Despite their importance, dusty reacting flows have been less studied and understood compared to gas phase as well as sprays. The addition of solid particles in a flowing gas stream can lead to strong couplings between the two phases, which can be of dynamic, thermal, and chemical nature. The dynamic coupling between the two phases is caused by the inertia that causes the phases to move with different velocities. Furthermore, gravitational, thermophoretic, photophoretic, electrophoretic, diffusiophoretic, centrifugal, and magnetic forces can be exerted on the particles. In general, magnetic, electrophoretic, centrifugal, photophoretic, and diffusiophoretic can be neglected. On the other hand, thermophoretic forces, caused by steep temperature gradients, can be important. The gravitational forces are almost always present and can affect the dynamic response of large particles. Understanding and quantifying the chemical coupling between two phases is a challenging task. However, all reacting particles begin this process as inert particles, and they must be heated before they participate in the combustion process. Thus, one must first understand the interactions of inert particles in a combustion environment. The in-detail understanding of the dynamics and structure of dusty flows can be only advanced by considering simple flow geometries such as the opposed-jet, stagnation-type. In such configurations the imposed strain rate is well characterized, and the in-depth understanding of the details of the physico-chemical processes can be systematically obtained. A number of computational and experimental studies on spray and particle flows have been conducted in stagnation-type configurations. Numerically, the need for a hybrid Eulerian-Lagrangian approach has been identified by Continillo and Sirignano, and the use of such approach has allowed for the prediction of the phenomenon of droplet flow reversal. Gomez and Rosner have conducted a detailed study on the particle response in the opposed-jet configuration, and the particle thermophoretic diffusivities were determined experimentally. Sung, Law and co-workers have conducted numerical studies on the effect of strain rate and temperature gradients on the dynamics of inert particles, as a way of understanding potential errors in experimental LDV data that may arise from thermophoretic forces. This investigation is a combined experimental and numerical study on the details of reacting dusty flows. The specific tasks are: (1) Experimental determination of laminar flame speeds, and extinction strain rates of dusty flows at normal- and micro-gravity as functions of the particle type, particle initial diameter, particle initial number density, and gas phase chemical composition; (2) Detailed numerical simulation of the experiments. Results are compared with experiments and the adequacy of theoretical models is assessed; and (3) Provision of enhanced insight into the thermo-chemical coupling between the two phases.

Andac, M. Gurhan↗

Semi-Supervised Learning of Lift Optimization of Multi-Element Three-Segment Variable Camber Airfoil

This chapter describes a new intelligent platform for learning optimal designs of morphing wings based on Variable Camber Continuous Trailing Edge Flaps (VCCTEF) in conjunction with a leading edge flap called the Variable Camber Krueger (VCK). The new platform consists of a Computational Fluid Dynamics (CFD) methodology coupled with a semi-supervised learning methodology. The CFD component of the intelligent platform comprises of a full Navier-Stokes solution capability (NASA OVERFLOW solver with Spalart-Allmaras turbulence model) that computes flow over a tri-element inboard NASA Generic Transport Model (GTM) wing section. Various VCCTEF/VCK settings and configurations were considered to explore optimal design for high-lift flight during take-off and landing. To determine globally optimal design of such a system, an extremely large set of CFD simulations is needed. This is not feasible to achieve in practice. To alleviate this problem, a recourse was taken to a semi-supervised learning (SSL) methodology, which is based on manifold regularization techniques. A reasonable space of CFD solutions was populated and then the SSL methodology was used to fit this manifold in its entirety, including the gaps in the manifold where there were no CFD solutions available. The SSL methodology in conjunction with an elastodynamic solver (FiDDLE) was demonstrated in an earlier study involving structural health monitoring. These CFD-SSL methodologies define the new intelligent platform that forms the basis for our search for optimal design of wings. Although the present platform can be used in various other design and operational problems in engineering, this chapter focuses on the high-lift study of the VCK-VCCTEF system. Top few candidate design configurations were identified by solving the CFD problem in a small subset of the design space. The SSL component was trained on the design space, and was then used in a predictive mode to populate a selected set of test points outside of the given design space. The new design test space thus populated was evaluated by using the CFD component by determining the error between the SSL predictions and the true (CFD) solutions, which was found to be small. This demonstrates the proposed CFD-SSL methodologies for isolating the best design of the VCK-VCCTEF system, and it holds promise for quantitatively identifying best designs of flight systems, in general.

Intelligent Systems↗

Spacecraft Modeling, Attitude Determination, and Control: Quaternion-Based Approach

Spacecraft attitude determination and control is an important part of a spacecraft to achieve its designed mission. As of today, many spacecrafts have been successfully launched, and most of them have performed well as they were designed. Many research papers have been published to address the attitude determination and control design problems. Several text books are available for students to learn the technology and for engineers to use as references. The most popular spacecraft models for attitude determination algorithms and control design methods are the Euler angle models and the quaternion models . The Euler angle models have been proved very efficient as the linearized models are controllable, and all standard linear control system design methods are directly applicable. The drawbacks related to the Euler angle methods are (a) the designs based on linearized models may not globally stabilize the original nonlinear spacecraft, i.e., the design may not work when the attitude of the spacecraft is far away from the point where the linearization is performed; (b) the models depend on the rotational sequences, this can be error prone if several teams work on the same project and they use different rotational sequences; (c) for any rotational sequence, there is a singular point where the model is not applicable; and (d) since most attitude determination methods use quaternion to represent the spacecraft attitude, there is a need to transform quaternion into Euler angles. On the other hand, for quaternion models, people have found controllers that can globally stabilize nonlinear spacecraft systems; the models do not depend on rotational sequences and they have no singular point; and the quaternion is provided by attitude determination system and ready to use. The main problem with the quaternion model based control system design is that the linearized quaternion model is not controllable. Therefore, most published design methods heavily rely on Lyapunov functions for the nonlinear spacecraft system. But there is no systematic way to obtain a desired Lyapunov functions. Moreover, the Lyapunov function based designs focus on the closed-loop system stability but pay little attention to the closed-loop system performance. In a series of papers, the author proposed some reduced quaternion models which lead to some controllable linearized spacecraft models. Therefore, all standard linear system theory can be directly applied to analyze and design the spacecraft control systems. We showed that, in some cases, the designed control system is not only optimal for the linearized system, but also globally stabilize the original nonlinear system . Clearly, the reduced quaternion models do not depend on rotational sequences. Due to the special structure of the linearized spacecraft model, some most important design methods, such as LQR design and robust pole assignment design are very simple, enjoy the analytical solutions for some problems, have direct connection to the performance measures, such as settling time, rising time , and percentage of overshoot . All these features are attractive for high quality control system designs. The idea mentioned above is then extended to more spacecraft control problems using specific actuators such as magnetic torque bars and control momentum gyroscopes. These types of actuators may not provide exactly desired torques. Most existing methods use different conversions to get approximate solutions, meaning that these actuators may generate a torque close to but not equal to the desired one. Using the reduced quaternion models that incorporate the actuators into the system model, the control inputs are not torques but the operational parameters. The main benefit of this idea is that the control actions are not approximate but accurate. As all actuators have their operational limit, design with input constraints are also considered in this book by using recently developed interior-point optimization techniques. This book grows up from my research on the spacecraft attitude determination and control design methods in more than a decade which is focused on using reduced quaternion models because of their merits stated above. The book provides all necessary background materials on orbital dynamics, rotations and quaternion, frequently used reference frames, transformations between reference frames, space environment and disturbance torques, ephemeris astronomical vector calculations and measurement instruments, spacecraft control actuators and their models, so that the readers will get a global picture and can apply all these information into the spacecraft system modeling, attitude determination, and spacecraft control system designs, which is the main purpose of this book. This book is different from existing books in that we focus on quaternion based spacecraft control system designs and we consider only attitude control system design related problems, from spacecraft modeling, to attitude determination and estimation, to control system design method selection, to control algorithm development, and to the simulation of the control system designs. Moreover, this book addresses different attitude control tasks in the spacecraft life cycle, including spacecraft maneuver, orbit raising, attitude control, and rendezvous. Finally, this book emphasizes the state space design methods rather than the classical frequency design methods.

Attitude determination and control↗

The Use of Sun Elevation Angle for Stereogrammetric Boreal Forest Height in Open Canopies

Stereogrammetry applied to globally available high resolution spaceborne imagery (HRSI; less than 5 m spatial resolution) yields fine-scaled digital surface models (DSMs) of elevation. These DSMs may represent elevations that range from the ground to the vegetation canopy surface, are produced from stereoscopic image pairs (stereo pairs) that have a variety of acquisition characteristics, and have been coupled with lidar data of forest structure and ground surface elevation to examine forest height. This work explores surface elevations from HRSI DSMs derived from two types of acquisitions in open canopy forests. We (1) apply an automated mass-production stereogrammetry workflow to along-track HRSI stereo pairs, (2) identify multiple spatially coincident DSMs whose stereo pairs were acquired under different solar geometry, (3) vertically co-register these DSMs using coincident spaceborne lidar footprints (from ICESat-GLAS) as reference, and(4) examine differences in surface elevations between the reference lidar and the co-registered HRSI DSMs associated with two general types of acquisitions (DSM types) from different sun elevation angles. We find that these DSM types, distinguished by sun elevation angle at the time of stereo pair acquisition, are associated with different surface elevations estimated from automated stereogrammetry in open canopy forests. For DSM values with corresponding reference ground surface elevation from spaceborne lidar footprints in open canopy northern Siberian Larix forests with slopes less than10, our results show that HRSI DSM acquired with sun elevation angles greater than 35deg and less than 25deg (during snow-free conditions) produced characteristic and consistently distinct distributions of elevation differences from reference lidar. The former include DSMs of near-ground surfaces with root mean square errors less than 0.68 m relative to lidar. The latter, particularly those with angles less than 10deg, show distributions with larger differences from lidar that are associated with open canopy forests whose vegetation surface elevations are captured. Terrain aspect did not have a strong effect on the distribution of vegetation surfaces. Using the two DSM types together, the distribution of DSM-differenced heights in forests (6.0 m, sigma = 1.4 m) was consistent with the distribution of plot-level mean tree heights (6.5m, sigma = 1.2 m). We conclude that the variation in sun elevation angle at time of stereo pair acquisition can create illumination conditions conducive for capturing elevations of surfaces either near the ground or associated with vegetation canopy. Knowledge of HRSI acquisition solar geometry and snow cover can be used to understand and combine stereogrammetric surface elevation estimates to co-register rand difference overlapping DSMs, providing a means to map forest height at fine scales, resolving the vertical structure of groups of trees from spaceborne platforms in open canopy forests.

Paul M Montesano↗

Dynamics Questions Associated with the AERCam Sprint Free-Flyer

The International Space Station will require the development of small robotic vehicles for such tasks as external inspection, monitoring of extravehicular activities (EVA's) and station build-up, and providing additional lighting at EVA worksites. The Autonomous EVA Robotic Camera (AERCam) family of free-flyers is currently being developed at NASA Johnson Space Center to perform these functions; the first member of the family is the AERCam Sprint vehicle. Many interesting dynamical questions are associated with the Sprint free-flyer. For instance, the reaction of a vehicle which is nearly spherically symmetric (such as Sprint) to a stuck-on thruster is significantly more complicated than that obtained for an idealized, perfectly spherical, spacecraft model. In particular, the real spacecraft will experience a form of forced nutation, with convergence towards either its major or minor principal axis, depending on both the applied torque and the mass properties of the vehicle. Furthermore, the body-fixed jet force vector may have a significant component along this principal axis, so giving rise to a considerable net linear acceleration of the spacecraft. The large velocity that can result is very important, as it may lead to collision with the nearby Orbiter, and is completely overlooked in the idealized analysis. This report will firstly briefly describe the stuck-on thruster dynamics of the real vehicle, and outline how the small products of inertia of the spacecraft determine the time constants of the motion. Secondly, the dynamical effects of a failed-off jet on the Sprint free-flyer will be described in more detail, and compared with the stuck-on thruster case. This will help to show whether the two malfunctions should be dealt with differently in flight. Finally, the stuck-on thruster detection software (known as the uncommanded motion algorithm) that is proposed to be flown on the Sprint vehicle will be analyzed, and all possible perturbation sources that may tend to give rise to false stuck-on thruster alarms quantified. It will be shown that false alarms can be triggered by discrete events such as a failed-off thruster, a glancing collision with Orbiter structure, or thruster saturation. They can also be triggered by a combination of errors introduced by constantly present sources such as thrust level errors, thruster misalignment, inertial cross-coupling, angular rate sensor noise, and structural vibrations induced by thruster firings. Based on this fact, the original plan to have the spacecraft enter safe mode whenever the uncommanded motion algorithm is triggered does not appear to be advisable. A better approach seems to be to provide the Sprint pilot with a warning whenever uncommanded motion is detected, and then allow the crew to determine whether safing the vehicle is appropriate.

Williams, Trevor↗

Assimilation of Precipitation Information Retrieved from Passive Microwave Sensors

Estimates of surface precipitation and the associated vertical latent heating structure can be retrieved from space-borne passive microwave sensors such as the TRMM Microwave Imager (TMI) and Special Sensor Microwave/Imager (SSM/I). Studies have shown that assimilation of microwave rain rates can improve the quality of global analysis and forecast. Numerical weather prediction (NWP) centers are beginning to make operational use of these data. In the next few years, there will be a gradual increase in microwave rain products available from operational and research satellites, culminating to a target constellation of 9 satellites to provide global rain measurements every 3 hours with the proposed Global Precipitation Measurement (GPM) mission to be launched around 2007. Realizing the full potential of these observations in data assimilation will require continued advances in retrieval algorithms, assimilation techniques, and model physics. I present results from two research efforts at NASA GSFC. The first is on the assimilation of tropical precipitation using temperature/moisture tendency corrections within a continuous variational assimilation framework to improve analyses and forecasts produced by the Goddard Earth Observing System (GEOS) global data assimilation system. Results show that assimilation of TMI and SSM/I rain rates improves not only precipitation and moisture, but also the related clouds, radiation energy fluxes, and large-scale circulations in GEOS analyses. The improved analyses also yield better short-range forecasts, quantitative precipitation forecast (QPF) threat scores, and storm track predictions. The second part consists of results from exploratory experiments on variational assimilation of convective and stratiform latent heating profiles within the general framework of model parameter estimation as a way to identify systematic model errors and optimize physical paremeterization schemes in global forecast and climate models.

Hou, Arthur Y.↗

Application of a Planar Doppler Velocimetry System to a High Reynolds Number Compressible Jet

A Planar Doppler Velocimetry (PDV) system has been constructed and used to investigate the instantaneous turbulent velocity structure of a round high-speed compressible air jet with a low-speed co-flow. The exit condition was Mach=0.85 at ambient pressure, yielding a Reynolds number of about 650,000 on diameter. The PDV system was installed at NASA Langley Research Center in the Small Anechoic Jet Facility (SAJF), a chamber in which both the acoustic and aerodynamic properties of jets can be studied. For this test, the goal was to gather data which can be used to relate the turbulence structure of the jet to the levels and character of the acoustic noise produced by the jet. The current PDV system can acquire single-velocity-component, single-shot, planar images (15ns exposures) at 30 Hz. For this paper, the primary data set consists of 240 frames of velocity data acquired with both the jet and the low-speed co-flow seeded with light-scattering articles. Thus, velocities could be measured everywhere in the jet shear layer, both in the jet fluid and in the entrained co-flow. Some data were also taken with only the jet flow seeded. These provided mixing concentration images along with the reduced velocity fields. Other images were taken with only the co-flow seeded. These produced unique quantitative images of high speed entrainment. Optical "laser speckle" noise is the largest source of random noise in pulsed PDV systems. Components for the PDV imaging system were specifically selected to minimize speckle noise. To reduce systematic velocity errors due to laser drift, a frequency monitoring reference leg with a temperature-tuned reference iodine cell, was employed. In the course of this study, a novel flow seeder was developed. It enabled continuously variable seeding of the flow with particles of Sheared Pyrogenic Amorphous Hydrophobic Silica (SPAHS). The seeder comprised a dry fluidized bed hopper and a supersonic nozzle "pickup." Shearing action in the pickup dispersed the seed material in an exceptionally fine cloud (approximately 0.3 micron). These particles followed the flow well, did not clump or cake on screens or model surfaces, and were not susceptible to evaporation. Because of the refractory nature of the particles, SPAHS seeding should also be applicable to anticipated future testing at high temperatures.

Smith, Michael W.↗

Real-Time Kennedy Space Center and Cape Canaveral Air Force Station High-Resolution Model Implementation and Verification

Customer: NASA's Launch Services Program (LSP), Ground Systems Development and Operations (GSDO), and Space Launch System (SLS) programs. NASA's LSP, GSDO, SLS and other programs at Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS) use the daily and weekly weather forecasts issued by the 45th Weather Squadron (45 WS) as decision tools for their day-to-day and launch operations on the Eastern Range (ER). For example, to determine if they need to limit activities such as vehicle transport to the launch pad, protect people, structures or exposed launch vehicles given a threat of severe weather, or reschedule other critical operations. The 45 WS uses numerical weather prediction models as a guide for these weather forecasts, particularly the Air Force Weather Agency (AFWA) 1.67 kilometer Weather Research and Forecasting (WRF) model. Considering the 45 WS forecasters' and Launch Weather Officers' (LWO) extensive use of the AFWA model, the 45 WS proposed a task at the September 2013 Applied Meteorology Unit (AMU) Tasking Meeting requesting the AMU verify this model. Due to the lack of archived model data available from AFWA, verification is not yet possible. Instead, the AMU proposed to implement and verify the performance of an ER version of the AMU high-resolution WRF Environmental Modeling System (EMS) model (Watson 2013) in real-time. The tasking group agreed to this proposal; therefore the AMU implemented the WRF-EMS model on the second of two NASA AMU modeling clusters. The model was set up with a triple-nested grid configuration over KSC/CCAFS based on previous AMU work (Watson 2013). The outer domain (D01) has 12-kilometer grid spacing, the middle domain (D02) has 4-kilometer grid spacing, and the inner domain (D03) has 1.33-kilometer grid spacing. The model runs a 12-hour forecast every hour, D01 and D02 domain outputs are available once an hour and D03 is every 15 minutes during the forecast period. The AMU assessed the WRF-EMS 1.33-kilometer domain model performance for the 2014 warm season (May-September). Verification statistics were computed using the Model Evaluation Tools, which compared the model forecasts to observations. The mean error values were close to 0 and the root mean square error values were less than 1.8 for mean sea-level pressure (millibars), temperature (degrees Kelvin), dewpoint temperature (degrees Kelvin), and wind speed (per millisecond), all very small differences between the forecast and observations considering the normal magnitudes of the parameters. The precipitation forecast verification results showed consistent under-forecasting of the precipitation object size. This could be an artifact of calculating the statistics for each hour rather than for the entire 12-hour period. The AMU will continue to generate verification statistics for the 1.33-kilometer WRF-EMS domain as data become available in future cool and warm seasons. More data will produce more robust statistics and reveal a more accurate assessment of model performance. Once the formal task was complete, the AMU conducted additional work to better understand the wind direction results. The results were stratified diurnally and by wind speed to determine what effects the stratifications would have on the model wind direction verification statistics. The results are summarized in the addendum at the end of this report. In addition to verifying the model's performance, the AMU also made the output available in the Advanced Weather Interactive Processing System II (AWIPS II). This allows the 45 WS and AMU staff to customize the model output display on the AMU and Range Weather Operations AWIPS II client computers and conduct real-time subjective analyses. In the future, the AMU will implement an updated version of the WRF-EMS model that incorporates local data assimilation. This model will also run in real-time and be made available in AWIPS II.

Numerical Weather Prediction↗

A More Accurate and Efficient Technique Developed for Using Computational Methods to Obtain Helical Traveling-Wave Tube Interaction Impedance

The phenomenal growth of commercial communications has created a great demand for traveling-wave tube (TWT) amplifiers. Although the helix slow-wave circuit remains the mainstay of the TWT industry because of its exceptionally wide bandwidth, until recently it has been impossible to accurately analyze a helical TWT using its exact dimensions because of the complexity of its geometrical structure. For the first time, an accurate three-dimensional helical model was developed that allows accurate prediction of TWT cold-test characteristics including operating frequency, interaction impedance, and attenuation. This computational model, which was developed at the NASA Lewis Research Center, allows TWT designers to obtain a more accurate value of interaction impedance than is possible using experimental methods. Obtaining helical slow-wave circuit interaction impedance is an important part of the design process for a TWT because it is related to the gain and efficiency of the tube. This impedance cannot be measured directly; thus, conventional methods involve perturbing a helical circuit with a cylindrical dielectric rod placed on the central axis of the circuit and obtaining the difference in resonant frequency between the perturbed and unperturbed circuits. A mathematical relationship has been derived between this frequency difference and the interaction impedance (ref. 1). However, because of the complex configuration of the helical circuit, deriving this relationship involves several approximations. In addition, this experimental procedure is time-consuming and expensive, but until recently it was widely accepted as the most accurate means of determining interaction impedance. The advent of an accurate three-dimensional helical circuit model (ref. 2) made it possible for Lewis researchers to fully investigate standard approximations made in deriving the relationship between measured perturbation data and interaction impedance. The most prominent approximations made in the analysis were addressed and fully investigated for their accuracy by using the three-dimensional electromagnetic simulation code MAFIA (Solution of Maxwell's Equations by the Finite Integration Algorithm) (refs. 3 and 4). We found that several approximations introduced significant error (ref. 5).

Kory, Carol L.↗

Swarm Flyby Gravimetry

This study describes a new technology for discerning the gravity fields and mass distribution of a solar system small body, without requiring dedicated orbiters or landers. Instead of a lander, a spacecraft releases a collection of small, simple probes during a flyby past an asteroid or comet. By tracking those probes from the host spacecraft, one can estimate the asteroid's gravity field and infer its underlying composition and structure. This approach offers a diverse measurement set,equivalent to planning and executing many independent and unique flyby encounters of a single spacecraft. This report assesses a feasible hardware implementation, derives the underlying models,and analyzes the performance of this concept via simulation.In terms of hardware, a small, low mass, low cost implementation is presented, which consists of a dispenser and probes. The dispenser contains roughly 12 probes in a tube and has a total size commensurate with a 6U P-Pod. The probes are housed in disc shaped sabots. When commanded,the dispenser ejects the top-most probe using a linear motor. The ejected probe separates from its sabots and unfolds using internal springs. There are two types of probes, each designed for a particular tracking modality. The reflective probe type, tracked by a telescope, unfolds to forma diffusely reflective sphere. The retroreflector probe type, tracked by a lidar, unfolds to form a corner-cube retroreflector assembly. Both types are designed to spherical so that their attitude doesn't affect the spacecraft's tracking performance.This analysis indicates that the point-mass term of small bodies larger than roughly 500 m in diameter can be observed from a host spacecraft that tracks locally deployed probes throughout a flyby to an uncertainty of better than 5%. The conditions by which this measurement is possible depends on the characteristics of the asteroid (size, type), the flyby velocity, and the type of tracking available (angles-only or angles+ranging). For most encounters, a few (1-3) well placed probes can be very effective, with marginal improvement for additional probes. Given realistic deployment errors, an encounter may require roughly 10-12 probes to ensure that 1-3 achieve their target. Long duration tracking of probes flying by large asteroids (>5 km diameter) can sometimes provide observability of the gravity field's first spherical harmonic, J( sub 2). In summary, this method offers a feasible, affordable approach to enabling or augmenting flyby science.

Atchison, Justin↗

Formal Safety Certification of Aerospace Software

In principle, formal methods offer many advantages for aerospace software development: they can help to achieve ultra-high reliability, and they can be used to provide evidence of the reliability claims which can then be subjected to external scrutiny. However, despite years of research and many advances in the underlying formalisms of specification, semantics, and logic, formal methods are not much used in practice. In our opinion this is related to three major shortcomings. First, the application of formal methods is still expensive because they are labor- and knowledge-intensive. Second, they are difficult to scale up to complex systems because they are based on deep mathematical insights about the behavior of the systems (t.e., they rely on the "heroic proof"). Third, the proofs can be difficult to interpret, and typically stand in isolation from the original code. In this paper, we describe a tool for formally demonstrating safety-relevant aspects of aerospace software, which largely circumvents these problems. We focus on safely properties because it has been observed that safety violations such as out-of-bounds memory accesses or use of uninitialized variables constitute the majority of the errors found in the aerospace domain. In our approach, safety means that the program will not violate a set of rules that can range for the simple memory access rules to high-level flight rules. These different safety properties are formalized as different safety policies in Hoare logic, which are then used by a verification condition generator along with the code and logical annotations in order to derive formal safety conditions; these are then proven using an automated theorem prover. Our certification system is currently integrated into a model-based code generation toolset that generates the annotations together with the code. However, this automated formal certification technology is not exclusively constrained to our code generator and could, in principle, also be integrated with other code generators such as RealTime Workshop or even applied to legacy code. Our approach circumvents the historical problems with formal methods by increasing the degree of automation on all levels. The restriction to safety policies (as opposed to arbitrary functional behavior) results in simpler proof problems that can generally be solved by fully automatic theorem proves. An automated linking mechanism between the safety conditions and the code provides some of the traceability mandated by process standards such as DO-178B. An automated explanation mechanism uses semantic markup added by the verification condition generator to produce natural-language explanations of the safety conditions and thus supports their interpretation in relation to the code. It shows an automatically generated certification browser that lets users inspect the (generated) code along with the safety conditions (including textual explanations), and uses hyperlinks to automate tracing between the two levels. Here, the explanations reflect the logical structure of the safety obligation but the mechanism can in principle be customized using different sets of domain concepts. The interface also provides some limited control over the certification process itself. Our long-term goal is a seamless integration of certification, code generation, and manual coding that results in a "certified pipeline" in which specifications are automatically transformed into executable code, together with the supporting artifacts necessary for achieving and demonstrating the high level of assurance needed in the aerospace domain.

Denney, Ewen↗

Design Protocols and Analytical Strategies that Incorporate Structural Reliability Models

Ceramic matrix composites (CMC) and intermetallic materials (e.g., single crystal nickel aluminide) are high performance materials that exhibit attractive mechanical, thermal, and chemical properties. These materials are critically important in advancing certain performance aspects of gas turbine engines. From an aerospace engineers perspective the new generation of ceramic composites and intermetallics offers a significant potential for raising the thrust/weight ratio and reducing NO(sub x) emissions of gas turbine engines. These aspects have increased interest in utilizing these materials in the hot sections of turbine engines. However, as these materials evolve and their performance characteristics improve a persistent need exists for state-of-the-art analytical methods that predict the response of components fabricated from CMC and intermetallic material systems. This need provided the motivation for the technology developed under this research effort. Continuous ceramic fiber composites exhibit an increase in work of fracture, which allows for 'graceful' rather than catastrophic failure. When loaded in the fiber direction these composites retain substantial strength capacity beyond the initiation of transverse matrix cracking despite the fact that neither of its constituents would exhibit such behavior if tested alone. As additional load is applied beyond first matrix cracking, the matrix tends to break in a series of cracks bridged by the ceramic fibers. Any additional load is born increasingly by the fibers until the ultimate strength of the composite is reached. Thus modeling efforts supported under this research effort have focused on predicting this sort of behavior. For single crystal intermetallics the issues that motivated the technology development involved questions relating to material behavior and component design. Thus the research effort supported by this grant had to determine the statistical nature and source of fracture in a high strength, NiAl single crystal turbine blade material; map a simplistic future strength envelope of the material; develop a statistically based reliability computer algorithm; verify the reliability model and computer algorithm-, and model stator vanes for rig tests. Thus establishing design protocols that enable the engineer to analyze and predict the mechanical behavior of ceramic composites and intermetallics would mitigate the prototype (trial and error) approach currently used by the engineering community. The primary objective of the research effort supported by this short term grant is the continued creation of enabling technologies for the macro-analysis of components fabricated from ceramic composites and intermetallic material systems. The creation of enabling technologies aids in shortening the product development cycle of components fabricated from the new high technology materials.

Duffy, Stephen F.↗

Design Protocols and Analytical Strategies that Incorporate Structural Reliability Models

Ceramic matrix composites (CMC) and intermetallic materials (e.g., single crystal nickel aluminide) are high performance materials that exhibit attractive mechanical, thermal and chemical properties. These materials are critically important in advancing certain performance aspects of gas turbine engines. From an aerospace engineer's perspective the new generation of ceramic composites and intermetallics offers a significant potential for raising the thrust/weight ratio and reducing NO(x) emissions of gas turbine engines. These aspects have increased interest in utilizing these materials in the hot sections of turbine engines. However, as these materials evolve and their performance characteristics improve a persistent need exists for state-of-the-art analytical methods that predict the response of components fabricated from CMC and intermetallic material systems. This need provided the motivation for the technology developed under this research effort. Continuous ceramic fiber composites exhibit an increase in work of fracture, which allows for "graceful" rather than catastrophic failure. When loaded in the fiber direction, these composites retain substantial strength capacity beyond the initiation of transverse matrix cracking despite the fact that neither of its constituents would exhibit such behavior if tested alone. As additional load is applied beyond first matrix cracking, the matrix tends to break in a series of cracks bridged by the ceramic fibers. Any additional load is born increasingly by the fibers until the ultimate strength of the composite is reached. Thus modeling efforts supported under this research effort have focused on predicting this sort of behavior. For single crystal intermetallics the issues that motivated the technology development involved questions relating to material behavior and component design. Thus the research effort supported by this grant had to determine the statistical nature and source of fracture in a high strength, NiAl single crystal turbine blade material; map a simplistic failure strength envelope of the material; develop a statistically based reliability computer algorithm, verify the reliability model and computer algorithm, and model stator vanes for rig tests. Thus establishing design protocols that enable the engineer to analyze and predict the mechanical behavior of ceramic composites and intermetallics would mitigate the prototype (trial and error) approach currently used by the engineering community. The primary objective of the research effort supported by this short term grant is the continued creation of enabling technologies for the macroanalysis of components fabricated from ceramic composites and intermetallic material systems. The creation of enabling technologies aids in shortening the product development cycle of components fabricated from the new high technology materials.

Duffy, Stephen F.↗

SCATHA mission termination report

The SCATHA (Spacecraft Charging at High Altitudes) satellite was operated from the Consolidated Space Test Center in Sunnyvale, California from February 1979 to May 1991. It was a spin stabilized vehicle in a highly eccentric orbit that collected data on spacecraft charging. The purpose of such data gathering was to predict and/or model the effects of the Earth's magnetic field on synchronous and near synchronous satellites. During the majority of its lifetime, attitude precession maneuvers were done every 10-15 days to maintain solar panel orientation. Maneuver planning was difficult due to the structural characteristics of SCATHA. It is cylindrically shaped and has seven booms ranging in length from 2 to 50 meters. These precession maneuvers induced predictable nutation that damped out after a few days. Eventually fuel began running low due to these frequent maneuvers. Experiments that had required the spin axis be in the orbit plane had already been turned off or had collected all their data. To increase the vehicle lifetime, the spin axis was moved to ecliptic normal. While this stopped the need for frequent attitude maneuvering (only two per year required now), this movement of the spin axis caused nutation that would not damp out for the remainder of the mission. This phase of the mission, with the ecliptic normal orientation, lasted for approximately three years. Although nutation never damped, data gathering was uninterrupted. In late 1990, when SCATHA's transmitter became seriously degraded, the Air Force decided to turn SCATHA off. This would only be done after the satellite was made 'safe'. The most difficult part of making the vehicle safe was quickly purging the fuel. Several plans were considered. The selected plan was to perform a series of 20 degree attitude precession maneuvers (3 days apart to allow for the worst nutation to damp) until the fuel was depleted. Although this sounded simple, the actual execution proved difficult. This was due to a nearly complete lack of available telemetry data, large undamped motion of the long booms, inadequacies in attitude determination software, and an error in the fuel level calculation software. This paper discusses the various proposed termination plans and execution of the selected one. Attitude determination methodologies, nutation from maneuvers, and effects of the flexible booms on the termination mission are presented and analyzed from a satellite analyst point of view.

Stakkestad, Kjell↗

Cross-sectional structural parameters from densitometry

Bone densitometry has previously been used to obtain cross-sectional properties of bone from a single X-ray projection across the bone width. Using three unique projections, we have extended the method to obtain the principal area moments of inertia and orientations of the principal axes at each scan cross-section along the length of the scan. Various aluminum phantoms were used to examine scanner characteristics to develop the highest accuracy possible for in vitro non-invasive analysis of cross-sectional properties. Factors considered included X-ray photon energy, initial scan orientation, the angle spanned by the three scans (included angle), and I(min)/I(max) ratios. Principal moments of inertia were accurate to within +/-3.1% and principal angles were within +/-1 degrees of the expected value for phantoms scanned with included angles of 60 degrees and 90 degrees at the higher X-ray photon energy (140 kVp). Low standard deviations in the error (0.68-1.84%) also indicate high precision of calculated measurements with these included angles. Accuracy and precision decreased slightly when the included angle was reduced to 30 degrees. The method was then successfully applied to a pair of excised cadaveric tibiae. The accuracy and insensitivity of the algorithms to cross-sectional shape and changing isotropy (I(min)/I(max)) values when various included angles are used make this technique viable for future in vivo studies.

NASA Center ARC↗

Size-density relations in dark clouds: Non-LTE effects

One of the major goals of molecular astronomy has been to understand the physics and dynamics of dense interstellar clouds. Because the interpretation of observations of giant molecular clouds is complicated by their very complex structure and the dynamical effects of star formation, a number of studies have concentrated on dark clouds. Leung, Kutner and Mead (1982) (hereafter LKM) and Myers (1983), in studies of CO and NH3 emission, concluded that dark clouds exhibit significant correlations between linewidth and cloud radius of the form delta v varies as R(0.5) and between mean density and radius of the form n varies as R(-1), as originally suggested by Larson (1981). This result suggests that these objects are in virial equilibrium. However, the mean densities inferred from the CO data of LKM are based on an local thermodynamic equilibrium (LTE) analysis of their 13CO data. At the very low mean densities inferred by LKM for the larger clouds in their samples, the assumption of LTE becomes very questionable. As most of the range in R in the density-size correlation comes from the clouds observed in CO, it seems worthwhile to examine how non-LTE effects will influence the derived densities. One way to assess the validity of LTE-derived densities is to construct cloud models and then to interpret them in the same way as the observed data. Microturbulent models of inhomogeneous clouds of varying central concentration with the linewidth-size and mean density-size relations found by Myers show sub-thermal excitation of the 13CO line in the larger clouds, with the result that LTE analysis considerbly underestimates the actual column density. A more general approach which doesn't require detailed modeling of the clouds is to consider whether the observed T sub R*(13CO)/T sub R*(12CO) ratios in the clouds studied by LKM are in the range where the LTE-derived optical depths (and hence column densities) can be seriously in error due to sub-thermal excitation of the 13CO molecule.

Maloney, P.↗

A comparison of cosmological hydrodynamic codes

We present a detailed comparison of the simulation results of various hydrodynamic codes. Starting with identical initial conditions based on the cold dark matter scenario for the growth of structure, with parameters h = 0.5 Omega = Omega(sub b) = 1, and sigma(sub 8) = 1, we integrate from redshift z = 20 to z = O to determine the physical state within a representative volume of size L(exp 3) where L = 64 h(exp -1) Mpc. Five indenpendent codes are compared: three of them Eulerian mesh-based and two variants of the smooth particle hydrodynamics 'SPH' Lagrangian approach. The Eulerian codes were run at N(exp 3) = (32(exp 3), 64(exp 3), 128(exp 3), and 256(exp 3)) cells, the SPH codes at N(exp 3) = 32(exp 3) and 64(exp 3) particles. Results were then rebinned to a 16(exp 3) grid with the exception that the rebinned data should converge, by all techniques, to a common and correct result as N approaches infinity. We find that global averages of various physical quantities do, as expected, tend to converge in the rebinned model, but that uncertainites in even primitive quantities such as (T), (rho(exp 2))(exp 1/2) persists at the 3%-17% level achieve comparable and satisfactory accuracy for comparable computer time in their treatment of the high-density, high-temeprature regions as measured in the rebinned data; the variance among the five codes (at highest resolution) for the mean temperature (as weighted by rho(exp 2) is only 4.5%. Examined at high resolution we suspect that the density resolution is better in the SPH codes and the thermal accuracy in low-density regions better in the Eulerian codes. In the low-density, low-temperature regions the SPH codes have poor accuracy due to statiscal effects, and the Jameson code gives the temperatures which are too high, due to overuse of artificial viscosity in these high Mach number regions. Overall the comparison allows us to better estimate errors; it points to ways of improving this current generation ofhydrodynamic codes and of suiting their use to problems which exploit their best individual features.

Kang, Hyesung↗