Search NASA⌕ Search

SEARCH · Search NASA

Results for “CALCINATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Microstructural characterization of plutonium oxalate and oxide particles by three-dimensional focused ion beam tomography

Focused ion beam (FIB) tomography was used to characterize three-dimensional (3D) internal microstructures of plutonium oxalate and oxide particles. Sequential two-dimensional (2D) sectioning and imaging using FIB and 3D image reconstruction were used to elucidate and distinguish internal pore microstructure and distribution in plutonium oxide particles calcined from plutonium oxalate precipitates. The results show that the plutonium oxide particles have a significant increase in pore volume fraction while retaining the exterior morphological shape of the corresponding oxalate precipitates. This technique enables the examination of the internal structure of radioactive microparticles for nuclear forensics that is not available with conventional microscopy.

36 MATERIALS SCIENCE↗

PEDOT-PSS coated ZnO/C hierarchical porous nanorods as ultralong-life anode material for lithium ion batteries

ZnO/C hierarchical porous nanorods were synthesized through one-pot wet-chemical reaction followed by thermal calcination. It was found that ZnO/C porous nanorods are composed of numerous nanograins, exhibiting a hierarchical micro/nanostructure. In-situ synchrotron high energy X-ray diffraction study revealed that ZnO/C hierarchical porous nanorods involve a two-step reversible lithiation mechanism during charge/discharge; and part of ZnO and Zn remains at the end of the first discharge and charge process, respectively, leading to a low coulombic efficiency in the initial few cycles. The electrochemical test demonstrated that the reversible capacity and the rate performance of ZnO/C hierarchical porous nanorods anode have been greatly improved by PEDOT-PSS coating, which could maintain a reversible capacity of 623.94 mA h g(-1) after 1500 cycles at 1 C. Its excellent high rate capability and long cycle stability were attributed to the high electronic conductivity of PEDOT-PSS coating layer and the hierarchical structures of ZnO/C porous nanorods. (C) 2015 Elsevier Ltd. All rights reserved.

anode↗

Process development for recovering critical elements from acid mine drainage

The rapid development of advanced technologies has increased the demand for critical elements, such as Mn, Co, and Ni. For this work, a systematic study was conducted to develop a process for producing high-purity Mn, Co, and Ni products from an acid mine drainage (AMD). As major contaminants, Fe and Al in the solution were sequentially precipitated and eliminated by elevating the pH to around 4.00 and 6.50, respectively. After that, a pre-concentrated slurry containing 3,794 mg/L Mn, 59 mg/L Co, 127 mg/L Ni, and 300 mg/L Zn was obtained by collecting the precipitates formed in the pH range of 6.50 to 10.00. The pH of the pre-concentrated slurry was decreased to around 5.00 by adding HCl to re-dissolve Co, Ni, and Zn for further purification. At this pH, greater than 50% of Mn remained undissolved, and filtration of the undissolved material resulted in a product with around 30 wt.% Mn. Sodium sulfide was added into the re-dissolved solution to selectively precipitate Co, Ni, and Zn while remaining Mn in the solution. Almost 100% of Co, Ni, and Zn but only around 15% of Mn were precipitated using a sulfur to metal molar ratio of 1 at pH 4.00. The sulfide precipitate was calcined at 200 °C for 2 h and then completely dissolved in 1.2 M HCl. The critical elements existing in the dissolved solution were efficiently separated using a two-stage solvent extraction process. Ultimately, Co and Ni products with almost 94% and 100% purity were obtained by sulfide and alkaline precipitation, respectively.

42 ENGINEERING↗

Mesoporous MoO 2 thin films for high rate Li + storage: Effect of crystallinity and porous structure

MoO 2 has attracted much recent attention as a high capacity energy storage material. While much of the current work on MoO 2 has been focused on the high capacity four-electron reduction, this reaction is limited to slow charging process due to the large volume change and phase transitions involved. In this study we focus on one-electron insertion reactions and demonstrate that ordered mesoporous thin films of MoO 2 can show signatures of pseudocapacitive charge storage. Mesoporous MoO 2 (mp-MoO 2 ) thin films were treated at different temperatures between 350 and 700 °C to explore the role of crystallinity and nanoscale structure on charging dynamics. The porosity and pore size decreased while the crystallinity and grain size increased as the calcination temperature increased. Materials processed at 600 °C showed the best electrochemical performance due to an optimized combination of high crystallinity and small grain size. These materials could be charged and discharged in 24 s while still achieving a Li + storage capacity of 158 mAh/g. While such thin film systems do not constitute a practical energy storage device, the work here provides structural design parameters for the production of future bulk nanoporous materials.

25 ENERGY STORAGE↗

Recovery of yttrium from fluorescent powder of cathode ray tube, CRT: Zn removal by sulphide precipitation

Highlights: • Treatment of fluorescent powder of CRT waste. • Factorial experimental designs to study acid leaching of fluorescent powder and the purification of leach liquors. • Recover of yttrium by precipitation using oxalic acid. • Suitable flowsheet to recover yttrium from fluorescent powder. - Abstract: This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2{sup 2} full factorial plan and the highest extraction yields for yttrium and zinc equal to 100% are observed under the following conditions: 3 M of sulphuric acid, 10% v/v of H{sub 2}O{sub 2} concentrated solution at 30% v/v, 10% w/w pulp density, 70 °C and 3 h of reaction. Two series of precipitation tests for zinc are carried out: a 2{sup 2} full factorial design and a completely randomized factorial design. In these series the factors investigated are pH of solution during the precipitation and the amount of sodium sulphide added to precipitate zinc sulphide. The data of these tests are used to describe two empirical mathematical models for zinc and yttrium precipitation yields by regression analysis. The highest precipitation yields for zinc are obtained under the following conditions: pH equal to 2–2.5% and 10–12% v/v of Na{sub 2}S concentrated solution at 10% w/v. In these conditions the coprecipitation of yttrium is of 15–20%. Finally further yttrium precipitation experiments by oxalic acid on the residual solutions, after removing of zinc, show that yttrium could be recovered and calcined to obtain the final product as yttrium oxide. The achieved results allow to propose a CRT recycling process based on leaching of fluorescent powder from cathode ray tube and recovery of yttrium oxide after removing of zinc by precipitation. The final recovery of yttrium is 75–80%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Transportation fuel production by combination of LDPE thermal cracking and catalytic hydroreforming

Highlights: • h-Beta samples were impregnated with Ni nitrate to achieve Ni contents of 1.5%, 4%, 7% and 10%. • Larger and more easily reducible metal particles were obtained on Ni 7%/h-Beta and Ni 10%/h-Beta. • Higher Ni contents increased the amount of gases at the expenses of diesel fractions. • Maximum selectivity to automotive fuels (∼81%) was obtained with Ni 7%/h-Beta. • Ni loading also enhanced olefins saturation up to Ni 7%/h-Beta. - Abstract: Fuel production from plastics is a promising way to reduce landfilling rates while obtaining valuable products. The usage of Ni-supported hierarchical Beta zeolite (h-Beta) for the hydroreforming of the oils coming from LDPE thermal cracking has proved to produce high selectivities to gasoline and diesel fuels (>80%). In the present work, the effect of the Ni loading on Ni/h-Beta is investigated in the hydroreforming of the oils form LDPE thermal cracking. h-Beta samples were impregnated with Ni nitrate, calcined and reduced in H{sub 2} up to 550 °C to achieve different Ni contents: 1.5%, 4%, 7% and 10%. Larger and more easily reducible metal particles were obtained on Ni 7%/h-Beta and Ni 10%/h-Beta. Hydroreforming tests were carried out in autoclave reactor at 310 °C, under 20 bar H{sub 2}, for 45 min. Ni content progressively increased the amount of gases at the expenses of diesel fractions, while gasoline remained approximately constant about 52–54%. Maximum selectivity to automotive fuels (∼81%) was obtained with Ni 7%/h-Beta. Ni loading also enhanced olefins saturation up to Ni 7%/h-Beta. High cetane indices (71–86) and octane numbers (89–91) were obtained over all the catalysts. Regarding the different studied Ni contents, Ni 7%/h-Beta constitutes a rather promising catalyst for obtaining high quality fuels from LDPE thermal cracking oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of biochar prepared from biogas digestate

Highlights: • Solid digestate (SD) is a potential feedstock for preparing biochars. • The optimal BET surface area of resulting biochar from SD is over 100 m{sup 2}/g. • The higher temperature leads to the increase in true density of resulting biochar, but exhibited a decreased higher heating value. • The SD-based biochar may be used as a biofertilizer due to the mesoporosity and the abundant in nutrient minerals. - Abstract: In the study, the biogas digestate was evaluated as a potential feedstock for preparing biochars at a broad temperature range of 300–900 °C. The physico-chemical and pore properties of the resulting biochars (denoted as SDBC, solid digestate biochar), including calorific value (higher heating value), surface area/pore volume/pore size distribution, true density, scanning electron microscopy – energy dispersive X-ray spectroscopy (SEM-EDS) and X-ray powder diffraction (XRD), were studied. It was found that the higher heating values of the SDBC products were on a decreasing trend as pyrolysis temperature increased, but they indicated an increase in true density. The results are probably associated with the active pyrolysis of the lignocellulosic fragments and the calcination (or shrinkage) processes, thus resulting in the increased contents of aromatic carbon clusters and main mineral constituents remained. Based on the pore properties, pyrolysis temperature at around 800 °C seemed to be the optimal condition for producing SDBC, where its Brunauer-Emmet-Teller (BET) surface area (>100 m{sup 2}/g) largely increased as compared to that of the digestate feedstock (<1 m{sup 2}/g). Furthermore, the main compositions of mineral ash in the resulting biochar could exist as phosphates, carbonates, or oxides of calcium and other alkali/alkaline earth elements. According to the data on EDS and XRD, more pores could be significantly generated under severe pyrolysis (>700 °C) due to the high aromaticity via the thermal decomposition of lignocelluloses and the volatilization of inorganic minerals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Conversion of biowastes to biomaterial: An innovative waste management approach

Highlights: • Study demonstrates that hydroxyapatite can be potentially produced from biowastes. • Eggshells and synthetic urine was used for hydroxyapatite synthesis. • Solution pH and stirring influenced hydroxyapatite formation. - Abstract: The study suggests that biowastes (eggshells and urine) can be potentially used as precursors to produce hydroxyapatite (HAp) biomaterial in a simple chemical process. A batch reactor was used in this work to produce HAp powder from eggshells and synthetic urine (SU). Fine powder of calcined eggshells was dissolved in water to produce aqueous calcium hydroxide. The solution was then mixed with concentrated SU in stoichiometric amounts corresponding to HAp (Ca/P molar ratio ∼ 1.67). The initial pH of the solution was alkaline (pH ∼ 8.5) and particles formed rapidly with slight mixing. Stirring the turbid solution for a longer period (72 h) did not show any visual change, but the particle size decreased slightly. When the pH of the solution was adjusted to 5, the solution was initially clear, but particle formation was apparent after 48 h stirring. It was noticed that at a slow stirring speed (100 rpm), film formation occurred on the solution, whereas at a higher stirring speed (500 rpm) no such film formation was observed. X-ray diffraction (XRD) analysis confirmed that the particles (formed at 500 rpm) were an amorphous calcium phosphate (CaP). Alkaline treatment at 80 °C for 2 h converted the amorphous CaP into HAp. Inductively coupled plasma mass spectrometry (ICP-MS) analysis of the particles (formed at 500 rpm) suggested that they are calcium-deficient HAp (Ca/P molar ratio 1.58).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Chemically Tunable Aspect Ratio Control and Laser Refrigeration of Hexagonal Sodium Yttrium Fluoride Upconverting Materials

Hexagonal sodium yttrium fluoride with Na 3x Y 2-x F 6 stoichiometry (β-NaYF) is a promising material for luminescence upconversion applications due to the narrow crystal field splitting of the Yb(III) ion’s lower 2 F 7/2 manifold. However, growing single crystals of β-NaYF remains an outstanding challenge due to thermal expansion stresses that cause cracking during melt growth. Here, we demonstrate a novel hydrothermal synthesis of β-NaYF with the ability to tune the aspect ratio from microplatelets to microrods with aspect ratios that match computationally predicted cavity (Mie) resonances. These crystals have a root-mean-square roughness below 1 nm after calcination, which makes them ideal for optical cavities. The β-NaYF microcrystals are doped with 10% Yb(III) cations and are used to build optomechanical laser-refrigeration devices consisting of a hexagonal β-NaYF crystal located at the end of a cantilever. Laser refrigeration of these devices by >12.5 °C is observed using calibrated measurements of both the cantilever’s fundamental eigenfrequency and a Boltzmann fit to crystal field luminescence from the Yb(III) ions.

36 MATERIALS SCIENCE↗

Surface Stabilization with Fluorine of Layered Ultrahigh-Nickel Oxide Cathodes for Lithium-Ion Batteries

High-nickel layered oxide cathodes are key to meet the demands of the electric vehicle industry because of their high specific capacity. However, commercialization of these materials is hindered by critical challenges, such as phase transitions, particle cracking, aggressive surface reactivity, and thermal instability. Cation doping along with surface coating has proven to be an effective way to circumvent some of these issues to a large extent. Herein, fluorine coating is employed on a high-nickel Li[Ni 0.95 Mn 0.015 Co 0.02 Al 0.01 Mg 0.005 ]O 2 (NMCAM) cathode via a solution route. Detailed structural and electrochemical analyses indicate fluorine largely decorates the surface at low enough calcination temperatures. The cathode with 1 mol % fluorine coating exhibits a capacity retention of 71% after 500 cycles as compared to 59% for the control sample when cycled to a high cutoff voltage of 4.3 V in a full cell configuration with graphite anode. Post-mortem analysis of cycled electrodes reveals that surface reactivity is a major contributor to capacity fade as compared to particle cracking. Fluorine coating reduces surface reactivity and the depth to which rock-salt phase is formed on the surface during cycling. The thermal stability is also enhanced after fluorine coating as the material shows less heat release at high states of charge. Furthermore, this work demonstrates an effective, economical, and scalable way to stabilize the surface with fluorine and enhance the electrochemical performance of high-nickel cathodes.

25 ENERGY STORAGE↗

Removing Fluoride from Double Four-Membered Rings Yielding Defect-Free Zeolites under Mild Conditions Using Ozone

We have investigated ozone treatment of as-made LTA zeolites under mild temperature conditions (175 °C) using experiments and periodic DFT as a method of energy savings and engineering defects such as silanol nests in comparison with conventional calcination at 550 °C. We have studied ozone treatment on LTA samples synthesized with 1,2-dimethyl-3-(4-methylbenzyl) imidazolium (denoted as “BULKY”) as the primary organic structure-directing agent (OSDA) and with various amounts of tetramethylammonium (TMA) as a secondary OSDA. Ozone treatment of LTA-BULKY at 175 °C was found to give defect-free, pristine LTA materials as determined by 29 Si NMR, 13 C NMR, Raman spectra, and DFT to assign the spectra. This represents a significant and unexpected finding: that fluoride ions can be completely removed from double four-membered rings (D4Rs) under such mild conditions. Furthermore, ozone treatment of LTA-BULKY-TMA samples removed BULKY but left behind TMA/F, giving a new and more diverse structural landscape of Si environments in LTA. Ab initio MetaDynamics calculations provide pathways with relatively low barriers, explaining how fluoride ions can be removed from D4Rs, leaving behind defect-free LTA materials under mild conditions.

36 MATERIALS SCIENCE↗

Striving toward noble-metal-free photocatalytic water splitting: The hydrogenated-graphene-TiO 2 prototype

Graphane, graphone and hydrogenated graphene (HG) have been extensively studied in recent years due to their interesting properties and potential use in commercial and industrial applications. The present study reports investigation of hydrogenated graphene/TiO 2-x (HGT) nanocomposites as photocatalysts for H 2 and O 2 production from water without the assistance of a noble metal co-catalyst. By combination of several techniques, the morphologies, bulk/atomic structure and electronic properties of all the powders were exhaustively interrogated. Hydrogenation treatment efficiently reduces TiO 2 nanoparticles, while the graphene oxide sheets undergo the topotactic transformation from a graphene-like structure to a mixture of graphitic and turbostratic carbon (amorphous/disordered) upon altering the calcination atmosphere from a mildly reducing to a H 2 -abundant environment. Remarkably, the hydrogenated graphene-TiO 2-x composite that results upon H 2 -rich reduction exhibits the highest photocatalytic H 2 evolution performance equivalent to low loading of Pt (~0.12 wt%), whereas the addition of HG suppresses the O 2 production. As a result, we propose that such an enhancement can be attributed to a combination of factors including the introduction of oxygen vacancies and Ti 3+ states, retarding the recombination of charge carriers and thus, facilitating the charge transfer from TiO 2 -x to the carbonaceous sheet.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A General Solution Route to Nanoporous Metal Oxide Films

Metal oxide semiconductors are of interest as efficient, stable, and low-cost photoanode materials for photoelectrochemical water splitting, but their characteristically poor charge transport properties remain a fundamental challenge to practical use. Nanoporous metal oxide films that feature open bicontinuous networks of nanocrystals and nanopores can overcome such inefficient charge transport to enable high-performance photoanodes. Here, this paper describes a general method to make high-quality nanoporous films of metal oxides by spin coating and calcining molecular inks that contain a porosity-generating block copolymer. Phase-pure nanoporous films of BiFeO 3 , FeWO 4 , WO 3 , Fe 2 O 3 , and TiO 2 serve to demonstrate the versatility of the approach. It is demonstrated that the crystallite size, film porosity, and film thickness can be independently tuned by adjusting the ink composition and film processing conditions. The method is extended to fabricate core–shell nanoporous films consisting of a nanoporous film coated in a thin shell of a second metal oxide, using WO 3 –BiVO 4 and BiFeO 3 –BiVO 4 as examples. Given its simplicity and flexibility, this solution-phase route should prove useful for making nanoporous films of many different materials for a variety of applications, including energy conversion and storage, catalysis, and chemical sensing.

coating materials↗

Structural and Electrochemical Characteristics of Ca-Doped “Flower-like” Li 4 Ti 5 O 12 Motifs as High-Rate Anode Materials for Lithium-Ion Batteries

Doped motifs offer an intriguing structural pathway toward improving conductivity for battery applications. Specifically, Ca-doped, three-dimensional “flower-like” Li 4–x Ca x Ti 5 O 12 (“x” = 0, 0.1, 0.15, and 0.2) micrometer-scale spheres have been successfully prepared for the first time using a simple and reproducible hydrothermal reaction followed by a short calcination process. The products were experimentally characterized by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) mapping, inductively coupled plasma optical emission spectrometry (ICP-OES), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge–discharge testing. Calcium dopant ions were shown to be uniformly distributed within the LTO structure without altering the underlying “flower-like” morphology. The largest lattice expansion and the highest Ti 3+ ratios were noted with XRD and XPS, respectively, whereas increased charge transfer conductivity and decreased Li + -ion diffusion coefficients were displayed in EIS for the Li 4–x Ca x Ti 5 O 12 (“x” = 0.2) sample. The “x” = 0.2 sample yielded a higher rate capability, an excellent reversibility, and a superior cycling stability, delivering 151 and 143 mAh/g under discharge rates of 20C and 40C at cycles 60 and 70, respectively. In addition, a high cycling stability was demonstrated with a capacity retention of 92% after 300 cycles at a very high discharge rate of 20C. In addition, first-principles calculations based on density functional theory (DFT) were conducted with the goal of further elucidating and understanding the nature of the doping mechanism in this study. The DFT calculations not only determined the structure of the Ca-doped Li 4 Ti 5 O 12 , which was found to be in accordance with the experimentally measured XPD pattern, but also yielded valuable insights into the doping-induced effect on both the atomic and electronic structures of Li 4 Ti 5 O 12 .

25 ENERGY STORAGE↗

Comprehensive Magnetic Study of Nanostructured Mesoporous Manganese Oxide Materials and Implications for Catalytic Behavior

Magnetic behavior of nanostructured mesoporous manganese oxide materials, designated UCT-1 and UCT-18, were studied using a combination of superconducting quantum interference device (SQUID) magnetometry and 55 Mn zero-field spin–echo nuclear magnetic resonance (NMR). Curie–Weiss fits to the magnetic susceptibility for the UCT-1 and UCT-18 samples calcined at 550 °C yielded paramagnetic moment values consistent with spin-only Mn 3+ ions in the α-Mn 2 O 3 phase ( S = 2, 4.90 μ B ). However, the magnetization and NMR results reported here clearly identify a small amount of the Mn 3 O 4 second phase (ferrimagnetic with T C ≈ 43 K) that does not appear in X-ray diffraction (XRD). We report the study resulted in the observation of fascinating magnetic behavior: (1) exchange bias, which occurs in cases where a ferromagnetic (or ferrimagnetic) phase forms a boundary with an antiferromagnetic phase and (2) a magnetic contribution attributed to uncompensated spins on the surfaces of the α-Mn 2 O 3 nanoparticles. The presence of Mn 3 O 4 and the interplay of Mn 3+ and Mn 2+ impact the catalytic properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Probing the Influence of Thermally Induced Structural Changes on the Microstructural Evolution in Shale using Multiscale X-ray Scattering Measurements

Various pathways to accelerate the recovery of hydrocarbons from unconventional subsurface environments have been proposed, including the use of high-temperature fluids. However, the influence of temperature on the structural and microstructural changes in complex subsurface materials characterized by compositional and morphological heterogeneity are not very well understood. In this study, in operando ultrasmall angle, small angle, and wide-angle X-ray scattering (USAXS/ SAXS/WAXS) measurements were performed to link the structural and morphological changes in shale when heated from 30 to 1150 °C. The structural changes observed from the wide-angle X-ray scattering measurements were complemented by the changes in the porosity, particle size, and surface morphology. Overall, we report the combined USAXS/SAXS measurements showed enhanced smoothness in the pore–solid interface on heating. The dehydroxylation of illite and calcination of calcium carbonate were noted prior to the formation of denser and sintered silicate and alumino-silicate phases such as Mg 2 SiO 4 (forsterite), Fe 0.3 Mg 0.7 (SiO 3 ) (enstatite), and Al 2.35 Si 0.64 O 4.82 (mullite).

54 ENVIRONMENTAL SCIENCES↗

Process Design and Techno-economic Analysis for Materials to Treat Produced Waters

Significant quantities of water are produced during enhanced oil recovery making these “produced water” streams attractive candidates for treatment and reuse. However, high concentrations of dissolved silica raise the propensity for fouling. In this paper, we report the design and economic analysis for a new ion exchange process using calcined hydrotalcite (HTC) to remove silica from water. This process improves upon known technologies by minimizing sludge product, reducing process fouling, and lowering energy use. Process modeling outputs included raw material requirements, energy use, and the minimum water treatment price (MWTP). Monte Carlo simulations quantified the impact of uncertainty and variability in process inputs on MWTP. These analyses showed that cost can be significantly reduced if the HTC materials are optimized. Specifically, R&D improving HTC reusability, silica binding capacity, and raw material price can reduce MWTP by 40%, 13%, and 20%, respectively. Optimizing geographic deployment further improves cost competitiveness.

04 OIL SHALES AND TAR SANDS↗