Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONNECTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Stable Polyurethane Coatings for Electronic Circuits

Alkane-based polyurethanes resist deterioration while maintaining good dielectric properties. Weight loss after prolonged immersion in hot water far less for alkane-based polyurethanes than for more common ether based polyurethanes, at any given oxygen content. Major uses of polyurethanes are as connector potting materials and conformal coatings for printed circuit boards.

Morris, D. E.↗

Practical aspects of instrumentation system installation, volume 13

A review of factors influencing installation of aircraft flight test instrumentation is presented. Requirements, including such factors as environment, reliability, maintainability, and system safety are discussed. The assessment of the mission profile is followed by an overview of electrical and mechanical installation factors with emphasis on shock/vibration isolation systems and standardization of the electric wiring installation, two factors often overlooked by instrumentation engineers. A discussion of installation hardware reviews the performance capabilities of wiring, connectors, fuses and circuit breakers, and a guide to proper selections is provided. The discussion of the installation is primarily concerned with the electrical wire routing, shield terminations and grounding. Also inclued are some examples of installation mistakes that could affect system accuracy. System verification procedures and special considerations such as sneak circuits, pyrotechnics, aircraft antenna patterns, and lightning strikes are discussed.

Borek, R. W.↗

High resolution, low cost solar cell contact development

The MIDFILM cell fabrication and encapsulation processes were demonstrated as a means of applying low-cost solar cell collector metallization. The average cell efficiency of 12.0 percent (AM1, 28 C) was achieved with fritted silver metallization with a demonstration run of 500 starting wafers. A 98 percent mechanical yield and 80 percent electrical yield were achieved through the MIDFILM process. High series resistance was responsible for over 90 percent of the electrical failures and was the major factor causing the low average cell efficiency. Environmental evaluations suggest that the MIDFILM cells do not degrade. A slight degradation in power was experienced in the MIDFILM minimodules when the AMP Solarlok connector delaminated during the environmental testing.

Mardesich, N.↗

Use of two-dimensional transmission photoelastic models to study stresses in double-lap bolted joints

The stress distribution in two hole connectors in a double lap joint configuration was studied. The following steps are described: (1) fabrication of photoelastic models of double lap double hole joints designed to determine the stresses in the inner lap; (2) assessment of the effects of joint geometry on the stresses in the inner lap; and (3) quantification of differences in the stresses near the two holes. The two holes were on the centerline of the joint and the joints were loaded in tension, parallel to the centerline. Acrylic slip fit pins through the holes served as fasteners. Two dimensional transmission photoelastic models were fabricated by using transparent acrylic outer laps and a photoelastic model material for the inner laps. It is concluded that the photoelastic fringe patterns which are visible when the models are loaded are due almost entirely to stresses in the inner lap.

Hyer, M. W.↗

Flight support system mechanisms

The Flight Support System (FSS) which contains twelve mechanisms (six different types) which are used for retention and positioning of a Multimission Modular Spacecraft (MMS) within the Space Shuttle's cargo bay during launch, retrieval, and servicing missions is described. Retention latches were designed to provide the capability for structural support of the MMS during launch and retrieval, and during servicing operations the mechanisms on the Positioning Platform provide the capability for positioning the MMS in virtually any orientation necessary for the work to be performed. In addition, there are mechanisms for matching and demating umbilical connectors and a mechanism for locking the Positioning Platform during maneuvers. Each Mechanism is driven by a Common Drive Unit. Manual overrides were provided for those mechanisms that would present a safety hazard for the crew, if they should fail.

Source record↗

Metals processing

The metals processing effort is directed towards improvement of performance and usefulness of materials through modification and control of shape and internal structure. Interaction of reactive gases, introduced into a plasma arc, with iron alloys were analyzed. The technology of magnesium production was assessed. The study of fast fluidized bed reactors is continued. Aspects of separation processes are being investigated. The development of high field superconducting composites for use in large magnetic fusion devices is also discussed. Processing, structure, and property relationships of superconducting materials and the substitution of precious metals in standard electrical contact and connector applications are tested. The influence of processing procedures on the structure of zircaloy and nickel base alloys with a goal of improving mechanical properties and performance is investigated. Investigation of the potential of metal insulator semiconductor junctions as photovoltaic devices is reported.

Source record↗

Apparatus and process for microbial detection and enumeration

An apparatus and process for detecting and enumerating specific microorganisms from large volume samples containing small numbers of the microorganisms is presented. The large volume samples are filtered through a membrane filter to concentrate the microorganisms. The filter is positioned between two absorbent pads and previously moistened with a growth medium for the microorganisms. A pair of electrodes are disposed against the filter and the pad electrode filter assembly is retained within a petri dish by retainer ring. The cover is positioned on base of petri dish and sealed at the edges by a parafilm seal prior to being electrically connected via connectors to a strip chart recorder for detecting and enumerating the microorganisms collected on filter.

Wilkins, J. R.↗

High voltage cabling for high power spacecraft

Studies by NASA have shown that many of the space missions proposed for the time period 1980 to 2000 will require large spacecraft structures to be assembled in orbit. Large antennas and power systems up to 2.5 MW size are predicted to supply the electrical/electronic subsystems, solar electric subsystems, solar electric propulsion, and space processing for the near-term programs. Platforms of 100 meters/length for stable foundations, utility stations, and supports for these multi-antenna and electronic powered mechanisms are also being considered. This paper includes the findings of an analytic and conceptual design study for large spacecraft power distribution, and electrical loads and their influence on the cable and connector requirements for these proposed large spacecraft.

Dunbar, W. G.↗

Space storable propulsion components development

The current development status of components to control the flow of propellants (liquid fluorine and hydrazine) in a demonstration space storable propulsion system is discussed. The criteria which determined the designs for the pressure regulator, explosive-actuated valves, propellant shutoff valve, latching solenoid-actuated valve and propellant filter are presented. The test philosophy that was followed during component development is outlined. The results from compatibility demonstrations for reusable connectors, flange seals, and CRES/Ti-6Al4V transition tubes and the evaluations of processes for welding (hand-held TIG, automated TIG, and EB), cleaning for fluorine service, and decontamination after fluorine exposure are described.

Hagler, R., Jr.↗

Status of fiberoptics technology for propulsion control systems

Optical sensors and optically controlled actuators for use in airbreathing engine control systems are discussed. The environmental conditions in which the aircraft will operate require the fiberoptic cables and optical connectors to perform reliably at temperatures over the -55 C to 260 C range. The status of fiberoptics technology for operation in this environment is reviewed.

Baumbick, R. J.↗

Technical support package: Large, easily deployable structures. NASA Tech Briefs, Fall 1982, volume 7, no. 1

Design and test data for packaging, deploying, and assembling structures for near term space platform systems, were provided by testing light type hardware in the Neutral Buoyancy Simulator. An optimum or near optimum structural configuration for varying degrees of deployment utilizing different levels of EVA and RMS was achieved. The design of joints and connectors and their lock/release mechanisms were refined to improve performance and operational convenience. The incorporation of utilities into structural modules to determine their effects on packaging and deployment was evaluated. By simulation tests, data was obtained for stowage, deployment, and assembly of the final structural system design to determine construction timelines, and evaluate system functioning and techniques.

Source record↗

SADE: A space experiment to demonstrate structural assembly

The Structural Assembly and Demonstration Experiment (SADE) demonstrates that the Shuttle is a suitable base for space construction; this includes a test of the Shuttle's control system to determine its performance when a long attached truss or beam is extended from the bay. Examples of Shuttle-related systems that will receive special attention are the RMS, the lighting system, and the crew assembly capabilities. A second purpose is to determine the extent to which the assembly results from the Neutral Buoyancy Simulator can be used to forecast the results of space assembly is determined. Finally, the SADE truss design will be validated by measuring the performance of the deployment, the special connectors, and the assembly methods.

Harrison, J. K.↗

High stability amplifier

An electrical RF signal amplifier for providing high temperature stability and RF isolation and comprised of an integrated circuit voltage regulator, a single transistor, and an integrated circuit operational amplifier mounted on a circuit board such that passive circuit elements are located on side of the circuit board while the active circuit elements are located on the other side is described. The active circuit elements are embedded in a common heat sink so that a common temperature reference is provided for changes in ambient temperature. The single transistor and operational amplifier are connected together to form a feedback amplifier powered from the voltage regulator with transistor implementing primarily the desired signal gain while the operational amplifier implements signal isolation. Further RF isolation is provided by the voltage regulator which inhibits cross-talk from other like amplifiers powered from a common power supply. Input and output terminals consisting of coaxial connectors are located on the sides of a housing in which all the circuit components and heat sink are located.

Adams, W. A.↗

Photovoltaic stand-alone modular systems, phase 2

The final hardware and system qualification phase of a two part stand-alone photovoltaic (PV) system development is covered. The final design incorporated modular, power blocks capable of expanding incrementally from 320 watts to twenty kilowatts (PK). The basic power unit (PU) was nominally rated 1.28 kWp. The controls units, power collection buses and main lugs, electrical protection subsystems, power switching, and load management circuits are housed in a common control enclosure. Photo-voltaic modules are electrically connected in a horizontal daisy-chain method via Amp Solarlok plugs mating with compatible connectors installed on the back side of each photovoltaic module. A pair of channel rails accommodate the mounting of the modules into a frameless panel support structure. Foundations are of a unique planter (tub-like) configuration to allow for world-wide deployment without restriction as to types of soil. One battery string capable of supplying approximately 240 ampere hours nominal of carryover power is specified for each basic power unit. Load prioritization and shedding circuits are included to protect critical loads and selectively shed and defer lower priority or noncritical power demands. The baseline system, operating at approximately 2 1/2 PUs (3.2 kW pk.) was installed and deployed. Qualification was successfully complete in March 1983; since that time, the demonstration system has logged approximately 3000 hours of continuous operation under load without major incident.

Naff, G. J.↗

Fiberoptics technology and its application to propulsion control systems

Current work on optical sensors and optically controlled actuators for use in air-breathing engine control systems is reviewed with particular reference to the design and operation of several new fiber-optic devices. These include a tachometer, a rotary position encoder, a Fabry-Perot interferometer and a rare-earth sensor for measuring engine gas temperatures, a high-temperature photoswitch designed for the range -55 to 260 C, and optical cables and connectors. The advantages of optics over conventional wire systems used for sensing and actuator control are briefly discussed.

Baumbick, R. J.↗

Computerized Interactive Harness Engineering

Computerized interactive harness engineering program inexpensive, interactive system for learning and using engineering approach to interconnection systems. Basically data-base system that stores information as files of individual connectors and handles wiring information in circuit groups stored as records.

Billitti, J. W.↗

Burnwire Simulator

Fuse-containing device simulates pyrotechnic firing circuitry. Simulator includes housing receptacle connector at one end, and fuse at opposite end. Fuse circuit useful in any system having complex built-in wiring for current pulse applications.

Bummer, G. L.↗

Wire-Identification Instrument

Instrument automatically tests each wire in multiwire cable and identifies specified wire to be segregated or labeled and locates wire connected to specified connector pin. Instrument made with readily available CMOS integrated circuits. More efficient and reliable than conventional continuity testers and less expensive than computer controlled units.

Lonborg, J. O.↗