Search NASA⌕ Search

SEARCH · Search NASA

Results for “Matrix Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Search for a standard model Higgs boson produced in association with a top-quark pair and decaying to bottom quarks using a matrix element method

A search for a standard model Higgs boson produced in association with a top-quark pair and decaying to bottom quarks is presented. Events with hadronic jets and one or two oppositely charged leptons are selected from a data sample corresponding to an integrated luminosity of 19.5fb -1 collected by the CMS experiment at the LHC in pp collisions at a centre-of-mass energy of 8TeV. In order to separate the signal from the larger tt¯ + jets background, this analysis uses a matrix element method that assigns a probability density value to each reconstructed event under signal or background hypotheses. The ratio between the two values is used in a maximum likelihood fit to extract the signal yield. The results are presented in terms of the measured signal strength modifier, μ, relative to the standard model prediction for a Higgs boson mass of 125GeV. The observed (expected) exclusion limit at a 95 % confidence level is μ < 4.2 (3.3), corresponding to a best fit value μ^ = 1.2 +1.6 -1.5 .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Computational Simulation of the High Strain Rate Tensile Response of Polymer Matrix Composites

A research program is underway to develop strain rate dependent deformation and failure models for the analysis of polymer matrix composites subject to high strain rate impact loads. Under these types of loading conditions, the material response can be highly strain rate dependent and nonlinear. State variable constitutive equations based on a viscoplasticity approach have been developed to model the deformation of the polymer matrix. The constitutive equations are then combined with a mechanics of materials based micromechanics model which utilizes fiber substructuring to predict the effective mechanical and thermal response of the composite. To verify the analytical model, tensile stress-strain curves are predicted for a representative composite over strain rates ranging from around 1 x 10(exp -5)/sec to approximately 400/sec. The analytical predictions compare favorably to experimentally obtained values both qualitatively and quantitatively. Effective elastic and thermal constants are predicted for another composite, and compared to finite element results.

Goldberg, Robert K.↗

Toward shell model interactions with credible uncertainties

Background: The nuclear shell model is a powerful framework for predicting nuclear structure observables, but relies on interaction matrix elements fit to experimental data as its inputs. Extending the shell model's applicability, particularly toward dripline nuclei, requires efficient fitting methods and credible uncertainty quantification. Traditional approaches face computational challenges and may underestimate uncertainties. Purpose: We develop and test a framework combining eigenvector continuation and Markov chain Monte Carlo to efficiently fit shell model interaction matrix elements and quantify their uncertainties. Methods: Eigenvector continuation is used to emulate shell model calculations, reducing computational costs. The emulator enables Markov chain Monte Carlo sampling to optimize interaction matrix elements and rigorously assess parametric uncertainties. Here, the framework is benchmarked using the USDB interaction in the 𝑠⁢𝑑 shell. Results: The emulator reproduces the USDB interaction with negligible error, validating its use in shell model fitting applications. However, we find that to obtain credible predictive intervals, the model defect of the shell model itself, rather than experimental or emulator error, must be taken into account in order to obtain credible uncertainties. Conclusions: The proposed framework provides an efficient and rigorous approach for fitting shell model interactions and quantifying uncertainties. Further, the normality assumption used in the past appears sufficient to describe the distribution of interaction matrix elements. However, it is crucial to account for model correlations to avoid underestimating uncertainties.

Nuclear forces↗

Flutter and Divergence Analysis using the Generalized Aeroelastic Analysis Method

The Generalized Aeroelastic Analysis Method (GAAM) is applied to the analysis of three well-studied checkcases: restrained and unrestrained airfoil models, and a wing model. An eigenvalue iteration procedure is used for converging upon roots of the complex stability matrix. For the airfoil models, exact root loci are given which clearly illustrate the nature of the flutter and divergence instabilities. The singularities involved are enumerated, including an additional pole at the origin for the unrestrained airfoil case and the emergence of an additional pole on the positive real axis at the divergence speed for the restrained airfoil case. Inconsistencies and differences among published aeroelastic root loci and the new, exact results are discussed and resolved. The generalization of a Doublet Lattice Method computer code is described and the code is applied to the calculation of root loci for the wing model for incompressible and for subsonic flow conditions. The error introduced in the reduction of the singular integral equation underlying the unsteady lifting surface theory to a linear algebraic equation is discussed. Acknowledging this inherent error, the solutions of the algebraic equation by GAAM are termed 'exact.' The singularities of the problem are discussed and exponential series approximations used in the evaluation of the kernel function shown to introduce a dense collection of poles and zeroes on the negative real axis. Again, inconsistencies and differences among published aeroelastic root loci and the new 'exact' results are discussed and resolved. In all cases, aeroelastic flutter and divergence speeds and frequencies are in good agreement with published results. The GAAM solution procedure allows complete control over Mach number, velocity, density, and complex frequency. Thus all points on the computed root loci can be matched-point, consistent solutions without recourse to complex mode tracking logic or dataset interpolation, as in the k and p-k solution methods.

Edwards, John W.↗

Accurate Q-Value for the ^{74}Se Double Electron Capture Decay

The Q value of the neutrinoless double electron capture (0{nu}ECEC) decay of ^{74}Se was measured by using the JYFLTRAP Penning trap. The determined value is 1209.169(49) keV, which practically excludes the possibility of a complete energy degeneracy with the second 2^{+} state (1204-205(7) keV) of ^{74}Ge in a resoant 0{nu}ECEC decay. We have also computed the associated nuclear matrix element by using a microscopic nuclear model with realistic two-nucleon interactions. The computed matrix element is found to be quite small. The failure of the resonant condition, combined with the small nuclear matrix element and needed p-wave capture, suppresses the decay rate strongly and thus excludes ^{74}Se as a possible candidate to search for resonant 0{nu}ECEC processes.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Novel formulations of CKM matrix renormalization

We review two recently proposed on-shell schemes for the renormalization of the Cabibbo-Kobayashi-Maskawa (CKM) quark mixing matrix in the Standard Model. One first constructs gauge-independent mass counterterm matrices for the up- and down-type quarks complying with the hermiticity of the complete mass matrices. Diagonalization of the latter then leads to explicit expressions for the CKM counterterm matrix, which are gauge independent, preserve unitarity, and lead to renormalized amplitudes that are non-singular in the limit in which any two quarks become mass degenerate. One of the schemes also automatically satisfies flavor democracy.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Reactive-transport modeling of fracture flow to quantify the changes in flow pathways from matrix thermal contraction and mineral precipitation and dissolution; influence of grid resolution

A series of reactive-transport models of Enhanced Geothermal Systems (EGS) were constructed using the reactive transport code PFLOTRAN to examine the effect of matrix thermal contraction and mineral dissolution/precipitation on fracture flow in the context of grid cell size and model complexity. It was found that for thermal drawdown at production well, the impact of fracture zone grid cell size is negligible.

Gatz-Miller, Hannah Sarah↗

P -wave π π scattering and the ρ resonance from lattice QCD

Here we calculate the parameters describing elastic I = 1, P-wave ππ scattering using lattice QCD with 2 +1 flavors of clover fermions. Our calculation is performed with a pion mass of m π ≈ 320 MeV and a lattice size of L ≈ 3.6 fm. We construct the two-point correlation matrices with both quark-antiquark and two-hadron interpolating fields using a combination of smeared forward, sequential and stochastic propagators. The spectra in all relevant irreducible representations for total momenta |$\vec{P}$| ≤ $\sqrt{3}\frac{2π}{L}$ are extracted with two alternative methods: a variational analysis as well as multiexponential matrix fits. We perform an analysis using Lüscher’s formalism for the energies below the inelastic thresholds, and investigate several phase shift models, including possible nonresonant contributions. We find that our data are well described by the minimal Breit-Wigner form, with no statistically significant nonresonant component. In determining the ρ resonance mass and coupling we compare two different approaches: fitting the individually extracted phase shifts versus fitting the t-matrix model directly to the energy spectrum. We find that both methods give consistent results, and at a pion mass of am π = 0.18295 (36) stat obtain gρππ = 5.69(13) stat (16) sys , am ρ = 0.4609(16) stat (14) sys , and am ρ /am N = 0.7476(38) stat (23) sys , where the first uncertainty is statistical and the second is the systematic uncertainty due to the choice of fit ranges.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multiscale Modeling of CO 2 Migration and Trapping in Fractured Reservoirs with Validation by Model Comparison and Real-Site Applications (Final Technical Report)

This report documents the accomplishments achieved during the project titled “Multiscale Modeling of CO 2 Migration and Trapping in Fractured Reservoirs with Validation by Model Comparison and Real-Site Applications” funded by the US Department of Energy, Office of Fossil Energy. The objectives of the project were to develop modeling capabilities for predicting CO 2 and brine migration in fractured reservoirs during geologic carbon storage and to investigate the feasibility of carbon storage in fractured reservoirs using the newly developed modeling capabilities. To achieve these objectives new mass transfer functions were developed to adapt existing dual-continuum approaches – a commonly used approach in hydrocarbon reservoir modeling – to the CO 2 -brine system. In the dual-continuum approach the undisturbed rock matrix and the fractures are modeled as two separate continua, which are coupled through mass exchange of CO 2 and brine between the two continua. Mass transfer functions represent the mass exchange between fractures and the rock matrix, without requiring highly resolved numerical grids of individual fractures, thus allowing large modeling domains relevant to geologic carbon storage questions (tens of meters to hundreds of kilometers). Mass transfer functions for the exchange of both free-phase CO 2 and brine between fractures and rock matrix were developed for both the injection phase and the post-injection phase. During the injection phase the fractures are filled with CO 2 , while the rock matrix is initially filled with brine. Therefore, a mass transfer function was developed that is based on vertical displacement of brine by CO 2 in the rock matrix due to gravitational forces. Once CO 2 injection ceases and CO 2 migrates away from the direct vicinity of the injection site, the fractures will begin to re-fill with brine, while the rock matrix will have high CO 2 saturations. For these conditions a mass transfer functions was developed that is based on spontaneous imbibition, as the pore spaces in the rock matrix are much smaller than in the fractures. For formations with low permeability or high capillary entry pressure of the rock matrix, free-phase CO 2 may not be able to enter the rock matrix. However, free-phase CO 2 at the interface between fractures and rock matrix can dissolve into brine resident in the rock matrix. Therefore, additional mass transfer functions were developed based on aqueous-phase diffusion of CO 2 through the rock matrix. These mass transfer functions are based on existing solutions for diffusion and were expanded to be applicable to a variety of block shapes relevant to dual-continuum modeling. Implementations of the newly developed mass transfer functions showed that they give accurate results when compared to highly resolved models. In addition to developing new transfer functions, a new vertically-integrated dual-continuum modeling framework was developed. This development takes advantage of fast vertical segregation of CO 2 and brine in the fractures due to the density difference between CO 2 and brine and the high permeability of the fractures. Therefore, a vertically-integrated vertical equilibrium model for the fractures is coupled with a vertically-distributed model for the rock matrix. The newly developed approach significantly reduces the computational effort, but is only accurate for fracture permeabilities of 100 mD or higher. Finally, the newly developed models were applied to real and hypothetical geologic carbon storage sites to investigate the feasibility of using fractured reservoirs for carbon storage. The general results were, that storage of CO 2 – both as free-phase and dissolved – is feasible, but that storage capacities are likely lower than in unfractured systems. While the high permeability of the fractures reduces the injection pressure (or permits higher injection rates), fast migration of CO 2 may limit the overall storage volume, because CO 2 may escape laterally with not enough of the rock matrix being swept for effective storage.

20 FOSSIL-FUELED POWER PLANTS↗

Thermo-mechanical response predictions for metal matrix composite laminates

An analytical micromechanical model is employed for prediction of the stress-strain response of metal matrix composite laminates subjected to thermomechanical loading. The predicted behavior of laminates is based upon knowledge of the thermomechanical response of the transversely isotropic, elastic fibers and the elastic-viscoplastic, work-hardening matrix. The method is applied to study the behavior of silicon carbide/titanium metal matrix composite laminates. The response of laminates is compared with that of unidirectional lamina. The results demonstrate the effect of cooling from a stress-free temperature and the mismatch of thermal and mechanical properties of the constituent phases on the laminate's subsequent mechanical response. Typical results are presented for a variety of laminates subjected to monotonic tension, monotonic shear and cyclic tensile/compressive loadings.

Aboudi, J.↗

Effects of Fe atoms on hardening of a nickel matrix: Nanoindentation experiments and atom-scale numerical modeling

Significant hardening effect due to Fe concentrations in Ni-based alloys with face-centered-cubic structure has been studied by using a combined experimental and atomistic-based computational approach via nanoindentation tests. The obtained experimental load–displacement data for the [0 0 1] crystal orientation reached a qualitative good agreement with molecular dynamics simulations results, leading to strong evidence that the main strengthening factors are associated to sluggish dislocation diffusion, reduced defect sizes and the nucleation of tetrahedral stacking faults. Here, interstitial type prismatic dislocation loops mainly formed by $\frac{1}{6}$$\langle$1 1 2$\rangle$ Shockley dislocations are nucleated during the loading process, where their interaction leads to the formation of pyramidal shaped stacking fault which are mainly created by $\frac{1}{3}$$\langle$1 0 0$\rangle$ Hirth dislocations lines. Observing both types of defects coexisting in the same plastic deformation zone by both approaches. Reported mechanical data, measured experimentally and interpreted numerically, are also in accordance with microstructural SEM and TEM investigations.

36 MATERIALS SCIENCE↗

Investigation of desorption of hydrogen gas from polymer matrix using thermal desorption analysis and finite element modeling

Polymer materials are used widely as sealing materials and liners in hydrogen storage and transportation infrastructure. During operating conditions, polymers are exposed to high pressure hydrogen gas periodically. When in contact, the hydrogen gas diffuses through the polymer material with ease due to its smaller sized molecules compared to the polymer molecules. In the event of rapid decompression of outside hydrogen gas, the hydrogen molecules within the polymer diffuse out. This process is known as the desorption of polymer and can cause blisters or cracking causing permanent damage to the polymer. Here, we used a combined experimental and modeling approach to investigate the desorption of the hydrogen gas in the polymer. Thermal desorption analysis (TDA) experiments were performed on the polymer sample exposed to the high-pressure hydrogen gas to measure the diffusion coefficient and equilibrium hydrogen concentration. Experiments also provided the quantity of hydrogen within the polymer during the desorption process which followed Fick’s law. However, for higher pressurization values, some anomaly was observed in the quantity of hydrogen remaining in the polymer sample. A continuum mechanics based coupled diffusion–deformation-damage model was deployed to simulate the gas desorption process in the material using the finite element method to understand its effect on the material. It was found that the anomaly in TDA results were due to the blister formation on the polymer surface which resulted in longer hydrogen retention. Simulations also showed that blister formation can be affected by multiple parameters such as the addition of filler particles, and pre-existing cavity size.

36 MATERIALS SCIENCE↗

Facilitating Screening of MOFs for Mixed Matrix Membranes Using Machine Learning and the Maxwell Model

Metal organic framework (MOF)-based mixedmatrix membranes (MMMs), which embed MOF particles in polymer matrices, combine the advantages of polymeric and inorganic membranes. Multiple previous studies have used the Maxwell model together with molecular simulations and machine learning (ML) to predict the performance of MOF/polymer MMMs. However, the assumption of rigid MOF frameworks in molecular simulations limited the accuracy of the data used in the predictions, particularly in predicting molecular diffusivities. We developed a novel workflow integrating ML models with consideration of MOF flexibility to predict the permeability and selectivity of 131,722 MMMs for CO 2 /CH 4 , O 2 /N 2 and He/H 2 separations. The full range of achievable MMM performance within the Maxwell model was analyzed, and several promising MOFs were identified using this workflow. This approach offers an efficient tool for screening any polymer and MOF combination in gas separation applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

ISOTROPIC INELASTIC COLLISIONS IN A MULTITERM ATOM WITH HYPERFINE STRUCTURE

A correct modeling of the scattering polarization profiles observed in some spectral lines of diagnostic interest, the sodium doublet being one of the most important examples, requires taking hyperfine structure (HFS) and quantum interference between different J-levels into account. An atomic model suitable for taking these physical ingredients into account is the so-called multiterm atom with HFS. In this work, we introduce and study the transfer and relaxation rates due to isotropic inelastic collisions with electrons, which enter the statistical equilibrium equations (SEE) for the atomic density matrix of this atomic model. Under the hypothesis that the electron–atom interaction is described by a dipolar operator, we provide useful relations between the rates describing the transfer and relaxation of quantum interference between different levels (whose numerical values are in most cases unknown) and the usual rates for the atomic level populations, for which experimental data and/or approximate theoretical expressions are generally available. For the particular case of a two-term atom with HFS, we present an analytical solution of the SEE for the spherical statistical tensors of the upper term, including both radiative and collisional processes, and we derive the expression of the emission coefficient in the four Stokes parameters. Finally, an illustrative application to the Na i D{sub 1} and D{sub 2} lines is presented.

74 ATOMIC AND MOLECULAR PHYSICS↗

Corrosion of U233-Doped Uranium Oxide using Microfluidics Methods

The aim of work this year has been to investigate the role of alpha (α)-radiation and hydrogen (H 2 ) on the corrosion of uranium oxide (UO 2 ) using a microfluidic device. The microfluidic device, termed the Particle-Attached Microfluidic Electrochemical Cell, (PAMEC), enables monitoring of the UO 2 electrochemical corrosion potential (E corr ) under different environments, including de-aerated conditions and in the presence of dissolved H 2 . The Si 3 N 4 window allows us to study morphological and chemical changes under an electron microscope. We have previously demonstrated that the PAMEC matches the results from bulk electrochemical tests with UO 2 [1]. We used the high specific activity uranium (U) isotope, 233 U, (t 1/2 = 160,000 years) incorporated into UO 2 , to generate a localized a-field. The objective of the experiments were to mimic the radiation environment that would be experience at the surface of aged spent nuclear fuel (SNF) during long-term geologic disposal under anoxic conditions. Wittman et al. [2] predicted that in the presence of a pure a-radiation field and under H 2 conditions, the concentration of the radiolytic oxidant H 2 O 2 would be suppressed or even eliminated. In a UO 2 corrosion experiment this would be exhibited through a lowering of the measured UO 2 corrosion potential compared to identical conditions in the absence of dissolved H 2 . We found that the predictions of Wittman and co-workers were supported and that the corrosion potential of the 233 U-doped UO 2 in solution lowered with presence of H 2 gas and increased in the absence of H 2 , when under anoxic conditions. The PAMEC experiments indicate that H 2 O 2 has been eliminated in a solution sparged with H 2 while exposed to an a-radiation field. The corrosion potential of the a-doped 233 U(10%)- 238 UO 2 in a solution sparged with Ar/H 2 matched the corrosion potential of 238 UO 2 in solution sparged with air. This clearly demonstrated that the H 2 O 2 had been eliminated and that the only oxidant present was O 2 in this system in complete agreement with the modeling results of Wittman et al. These results point to the need to improve the Fuel Matrix Degradation (FMD) Process Model training data set that is being used in the FMD surrogate model that is being developed for the repository program. The incorporation of realistic radiation chemistry will improve the scientific basis for the FMD Model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Micromechanics of metal matrix composites using the Generalized Method of Cells model (GMC) user's guide

A user's guide for the program gmc.f is presented. The program is based on the generalized method of cells model (GMC) which is capable via a micromechanical analysis, of predicting the overall, inelastic behavior of unidirectional, multi-phase composites from the knowledge of the properties of the viscoplastic constituents. In particular, the program is sufficiently general to predict the response of unidirectional composites having variable fiber shapes and arrays.

Aboudi, Jacob↗