SEARCH · Search NASA

Results for “Metal Loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Scalable preparation of oxygen carriers for chemical looping

Wet impregnation of active metal precursors into porous substrates, together with selective adsorption of the precursors on the pore surfaces, enables transition metal oxides derived from the precursors to disperse throughout the substrate, even at the nanoscale, without increased sintering or agglomeration, thereby forming oxygen carriers suitable for chemical looping. The porous substrate can be an oxide, for example SiO 2 . The oxygen carriers can comprise relatively large oxide loadings of over about 20 wt % and exhibit high reactivity over many regeneration cycles with substantially no loss in oxygen transport capacity or decrease in kinetics. The use of multiple transition metal oxides, for example NiO in addition to CuO, can greatly enhance chemical looping performance.

O′Malley, Kyle↗

DOE OSTI2024

Optimal Geometry for Focused Ion Beam-Milled Samples for Direct-Pull Micro-Tensile Testing Performed In Situ in a Scanning Electron Microscope

A thorough procedure was developed to efficiently manufacture dogbone samples using focused ion beam (FIB) milling for micro-tensile testing. A Bruker PI 89 PicoIndenter, Billerica, MA, USA, was used as a case study, although the analysis and results are applicable to other micro-mechanical testing systems capable of mounting a standard, Ø12.7 mm × Ø3.2 mm pin, scanning electron microscopy (SEM) pin stub (Ted Pella, Redding, CA, USA). Nine dogbones were made from an Fe-45Cu alloy additively manufactured using powder-fed laser-directed energy deposition (DED-LB). Testing showed that fracture was confined to the gauge section for all dogbones and that the fracture mode, ductile vs. brittle, was entirely dependent on the grain orientation relative to the loading direction. The analysis showed that the measured plastic strain to failure can vary from >11% (optimal geometry) to <1% (non-optimal geometry) in micro-tensile testing of high-tensile-strength (>1 GPa) metallic materials. Subsequently, a finite element analysis (FEA) was conducted to identify the improved dogbone geometries. A total of ten thousand dogbone geometries were tested, and their dimensions were defined by a set of four adjustable parameters (corner radius, load surface angle, load surface length, and dogbone head length). The gauge width and gauge length were fixed to 4 µm and 10 µm, respectively. Three-dimensional surface plots of the stress concentration as a function of two parameters were used to identify the optimal ranges of parameter values. The addition of maximum width and length constraints, measuring 25 µm and 30 µm, respectively, allowed us to identify an optimal geometry at load surface angles of 30° and 45°. Their respective dimensions (corner radius, load surface length, and dogbone head length) are, in µm, 12, 6, and 7 and 10, 7, and 7. Testing these two optimal geometries with a range of gauge lengths from 4 to 20 µm showed that smaller gauge lengths only slightly reduced the detrimental stress concentration outside the gauge section. However, smaller gauge lengths will notably improve the FIB surface polishing step as tapering is reduced with smaller dogbone lengths.

Chemistry↗

NASA NTRS1999

Catalyst Development for Hydrogen Peroxide Rocket Engines

The development of various catalysts of hydrogen peroxide was conducted for the applications of liquid rocket engines. The catalyst development includes silver screen technology, solid catalyst technology, and homogeneous catalyst technology. The silver screen technology development was performed with 85% (by weight) hydrogen peroxide. The results of this investigation were used as the basis for the catalyst design of a pressure-fed liquid-fueled upper stage engine. Both silver-plated nickel 200 screens and pure silver screens were used as the active metal catalyst during the investigation, The data indicate that a high decomposition efficiency (greater than 90%) of 85% hydrogen peroxide can be achieved at a bed loading of 0.5 lbm/sq in/sec with both pure silver and silver plated screens. Samarium oxide coating, however, was found to retard the decomposition process and the catalyst bed was flooded at lower bed loading. A throughput of 200 lbm of hydrogen peroxide (1000 second run time) was tested to evaluate the catalyst aging issue and performance degradation was observed starting at approximately 400 seconds. Catalyst beds of 3.5 inch in diameter was fabricated using the same configuration for a 1,000-lbf rocket engine. High decomposition efficiency was obtained with a low pressure drop across the bed. Solid catalyst using precious metal was also developed for the decomposition of hydrogen peroxide from 85% to 98% by weight. Preliminary results show that the catalyst has a strong reactivity even after 15 minutes of peroxide decomposition. The development effort also includes the homogeneous catalyst technology. Various non-toxic catalysts were evaluated with 98% peroxide and hydrocarbon fuels. The results of open cup drop tests indicate an ignition delay around 11 ms.

Morlan, P. W.↗

DOE OSTI2023

Determination of film thicknesses of metal oxides prepared by atomic layer deposition on SBA-15

ZrO 2 and CeO 2 films were grown in SBA-15 by Atomic Layer Deposition (ALD) to loadings of 0.92 g oxide/g SBA-15. Scanning Transmission Electron Microscopy (STEM) with Energy Dispersive Spectra (EDS) showed that the oxides grew uniformly inside the mesopores. Film thicknesses were then analyzed as a function of the number of ALD cycles using three methods: 1) mass changes assuming bulk densities for the films; 2) changes in pore size from Barret-Joyner-Halenda (BJH) analysis with N 2 adsorption isotherms; and 3) small-angle X-ray scattering (SAXS). Film thicknesses assuming bulk densities were between 6 and 8 times smaller than those obtained from BJH analysis. SAXS analysis gave film thicknesses that were approximately twice that obtained from bulk densities. Here, possible explanations of the discrepancies between these methods are discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Effect of local structure and stoichiometry on the dynamic behavior of bi-metal interfaces

Molecular dynamics (MD) simulations are performed to investigate the failure behavior of Al/Al, Al/Fe, and Al/AlFe bi-layers under high strain-rate shock loading. Additional simulations are performed to invesigate solely the tensile response of these systems and to isolate the effects of loading history on damage and failure. Specifically, the compression stage of the shock is excluded from the tensile simulations. This study shows that local structure variation, including the introduction of serrations, plays different roles in controlling damage nucleation depending on the specific loading condition. Under shock loading, the stress for void nucleation and the resulting void distribution is insensitive to an interface structure, whereas under pure tensile loading, the opposite is true, even though the strain rate is comparable. The above difference can be explained based on the corresponding change in the total deformation prior to damage nucleation under shock loading, which is missing from the pure tensile loading. Therefore, it is concluded that whether local interface structure matters under high strain-rate loading depends on the specific loading history and the stress state: the local structure variation matters only when it alters the deformation behavior, and subsequently, damage nucleation and evolution.

36 MATERIALS SCIENCE↗

NASA NTRS2024

Characterizing the Structure of Lithium Metal Batteries using Local Ultrasonic Resonance Spectroscopy (LURS)

Safe use of high energy density batteries is critical for electrifying aerospace and other transportation sectors. Nondestructive evaluation (NDE) techniques are being developed for characterizing battery structures throughout their lifetimes so that damage mechanisms can be better understood, and prognostic tools can be developed. In this study Local Ultrasonic Resonance Spectroscopy (LURS) is applied to lithium metal pouch cell batteries of a variety of form-factors that are brought from fabrication to end of life under different charge rates, temperatures, and loading scenarios. LURS data shows improved sensitivity to changes in structure in comparison to amplitude-based methods, allowing differences in damage development to be identified as well as giving opportunities for quality control in manufacturing.

Ultrasound↗

DOE OSTI2020

PdPt-TiO 2 nanowires: correlating composition, electronic effects and O-vacancies with activities towards water splitting and oxygen reduction

Here we report the optimization of both the support and the active phase of PdPt NPs supported on TiO 2 nanowires to obtain highly active electro/photocatalysts for the oxygen reduction and water splitting reactions. This system displayed strong metal-support interactions, high concentration of oxygen vacancies, and PdPt NP were ~2 nm in size. By optimizing the loading of PdPt, both the photo- and electrocatalytic activities were improved compared to commercial materials. Interestingly, a volcano plot was obtained from the activity and the PdPt composition, and the Pd 0.22 Pt 0.78 -TiO 2 /C sample afforded the optimal performance. For instance, the amount of hydrogen produced from water splitting was 11.6 mmol/g catalyst . For the ORR, the activity was similar to a commercial Pt catalyst, but a lower E onset (0.87 V RHE vs w 0.95 V RHE ) was detected. The variations in the activities with the composition correlated well with the variations in the electronic effects and the concentration of oxygen vacancies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Twin nucleation and growth in hexagonal close-packed metals: The role of slip-mediated plasticity on twin embryo formation and evolution

Twinning is a key deformation mechanism in hexagonal close-packed (hcp) metals, which are typified by a lack of easily activated slip systems that can accommodate a general state of loading. Pragmatically, the nucleation and evolution of twin domains occurs concomitantly with slip, such that the eventual twin network is conditioned by both external and internal stresses resulting, among others, from the evolution of dislocations. However our understanding of the interplay between dislocations, and twin nucleation and stability remains limited. This work focuses on elucidating the influence of dislocation-mediated plasticity on the formation, growth, and stability of twin embryos. First, a new mesoscale spectral crystal plasticity-twinning framework is developed and used to quantify the change in the free energy landscape following the nucleation {$10\bar{1}2$} of twins in Mg. Representative twin morphologies are modeled under conditions of limited and profuse slip activity, which are emulative of small- and bulk-scale samples, respectively. Then, the driving traction profiles around twin embryos are investigated via a sharp interface approach to obtain insights into how concurrent slip-mediated plasticity can influence the growth/stabilization of nanometric twins. The driving traction profiles are further utilized to determine the stability of twin embryos post loading. The initial dislocation density in the samples, and within the different domains (i.e., twin vs. parent), is seen to have a significant effect on the twin nucleation stress. Namely, the activation of high levels of concomitant plasticity in the parent grain is seen to significantly drive the formation of nanometric twin nuclei at stresses as low as 250 MPa. Further, the sharp interface analysis reveals that profuse plasticity in the parent grain simultaneously alters the forward and back stresses, such that the magnitude/polarity of the driving tractions become increasingly favorable for nanometric twin growth when slip is active. Finally, prior plasticity in the parent grain is seen to result in favorable driving tractions for nanometric twin growth, even at applied stresses as low as ~ 100 MPa. In conclusion, these results are in stark contrast to a case without any dislocations, wherein applied stresses as high as ~ 500 MPa are necessary to grow the twin domains.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Rapid recovery of At-211 by extraction chromatography

The near quantitative separation, purification, and recovery of 211 At has been demonstrated through an extraction chromatography process which utilizes porous beads impregnated with 3-octanone, resulting in an elution yield of 92–95%. Moreover, the rapid nature of this process, <20 min, was achieved after dissolution of a Bi metal target in HNO 3 following retrieval from the beamline after α-particle bombardment. The solution was directly loaded onto the column with no volume or acidity adjustment. The column was washed with HNO 3 and H 2 O, and 211 At was eluted with ethanol, collecting roughly 87–93% in 1 mL. This process of recovering high purity 211 At, in near quantitative yields, represents a significant advance in At separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Cathode-Confined Polysulfide Retention-Release Reprograms Li 2 S Deposition in High-Loading Li–S Batteries

High-loading lithium-sulfur (Li-S) cells operated with lean electrolyte are limited by polysulfide crossover to Li metal and by transport-limited liquid-solid conversion that forms passivating Li 2 S films. Here, we show that a cathode-facing separator coating of carboxylated multiwalled carbon nanotubes acts as a cathode-confined polysulfide reservoir with intermediate binding. Early in discharge it captures newly generated polysulfides at the separator interface, suppressing shuttle reactions. As polysulfides are consumed, the reservoir buffers concentration gradients and feeds reactants back to the cathode, shifting Li 2 S deposition from burst-like film growth to progressive, three-dimensional, porous formation. Synchrotron XRD and S K-edge XANES, together with Scharifker–Hills nucleation analysis and depth-of-discharge EIS/DRT, substantiate this coupled transport–reaction control. With 4.3 mg S cm -2 and E/S = 5, cells reach 4.2 mAh cm -2 and retain 90% capacity over 100 cycles at 20 °C.

25 ENERGY STORAGE↗

DOE OSTI2023

Annual report for DOE VTO

Carbon fiber (CF)/polymer composites are a transformative class of high-performance, lightweight material, where high aspect-ratio CFs reinforce a polymer matrix and exceed the strength of steel alloys at a fraction of the density. Despite the advantages of such a class of material, the broader implementation of CF composites in a range of automotive, aerospace, and energy applications is hindered by limitations of current manufacturing methods. These current techniques (e.g., hand lay-up, wet filament winding) are costly and impose severe limitations on fiber placement, orientation, and angle, and thus a composite’s ultimate properties. Today’s CF composites are expensive to manufacture, limited in form factor, and utilize costly and sub-optimal continuous filament CF. Advanced additive manufacturing (AM) processes, combined with computational design optimization and new approaches to resin development, offer alternative design and manufacturing paradigms that have the realistic potential to lift these constraints. Such integrated AM approaches could thus help to realize the full potential of CF composite materials. One relevant application of CF composite materials where manufacturing constraints limit the cost-benefit ratio is in the manufacture of high-performance composite pressure vessels for onboard compressed natural gas (CNG) storage. Current CNG storage vessels (Types 3–5) are made from load-bearing filament-wound carbon-fiber composite and are ~3.5 times as expensive as an all-metallic Type-1 vessel. This cost is invariably tied to the complex and labor-intensive nature of conventional filament winding processes and the large volumes of expensive high tensile-strength CF tow feedstock required in manufacture. Our proposed approach to CNG storage vessel manufacture is based on a combination of AM technologies for CF composite printing and design optimization tools that were pioneered at Lawrence Livermore National Laboratory (LLNL), with advances in resin/composite formulation enabled by chemical and nano-material modification. Through the successful development of this technology, LLNL seeks to demonstrate the capability for advanced CNG storage vessel manufacture at reduced cost with no reduction in performance versus the most advanced, extant Type-5 designs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NASA NTRS1972

Apollo couch energy absorbers

Load attenuators for the Apollo spacecraft crew couch and its potential applications are described. Energy absorption is achieved through friction and cyclic deformation of material. In one concept, energy absorption is accomplished by rolling a compressed ring of metal between two surfaces. In another concept, energy is absorbed by forcing a plastically deformed washer along a rod. Among the design problems that had to be solved were material selection, fatigue life, ring slippage, lubrication, and friction loading.

Wesselski, C. J.↗

NASA NTRS1976

Filament-reinforced metal composite pressure vessel evaluation and performance demonstration

Two different Kevlar-49 filament-reinforced metal sphere designs were developed, and six vessels of each type were fabricated and subjected to fatigue cycling, sustained loading, and hydrostatic burst. The 61 cm (24 inch) diameter Kevlar-49/cryoformed 301 stainless steel pressure vessels demonstrated the required pressure cycle capability, burst factor of safety, and a maximum pressure times volume divided by weight (pV/W) performance of 210 J/g (834 000 in-lb/lbm) at burst; this represented a 25 to 30% weight saving over the lightest weight comparable, 6A1-4V Ti, homogeneous pressure vessel. Both the Kevlar/stainless steel design and the 97 cm (38 inch) diameter Kevlar-49/2219-T62 aluminum sphere design demonstrated nonfragmentation and controlled failure mode features when pressure cycled to failure at operating pressure. When failure occurred during pressure cycling, the mode was localized leakage and not catastrophic. Kevlar/stainless steel vessels utilized a unique conical boss design, and Kevlar/aluminum vessels incorporated a tie-rod to carry port loads; both styles of polar fittings performed as designed during operational testing of the vessels.

Landes, R. E.↗

NASA NTRS1976

Shock-induced fine-grained recrystallization of olivine - Evidence against subsolidus reduction of Fe/2+/

Electron spin resonance (ESR) studies have been carried out on three single grains of terrestrial olivine (Fo90) shock loaded along the 010 line to peak pressures of 280, 330, and 440 kbar. The results indicate that neither metallic Fe similar to that observed in returned lunar soils nor paramagnetic Fe(3+) caused by oxidation of Fe(2+) has been produced in these shock experiments. Trace amounts of Mn (2+) have been detected in both shocked and unshocked olivine. The ESR signals of Mn(2+) show spectral features which are found to correlate with the degree of shock-induced recrystallization observed petrographically. The increasing mass fraction of recrystallized olivine correlates with increasing shock pressures. This phenomenon is modelled assuming it results from the progressive effect of the shock-induced transformation of the olivine to a yet unknown high-pressure phase and its subsequent reversion to the low-pressure olivine phase. The mass fraction of recrystallized material is predicted to be nearly linear with shock pressure.

Ahrens, T. J.↗

NASA NTRS1978

Quantitative ultrasonic evaluation of mechanical properties of engineering materials

Current progress in the application of ultrasonic techniques to nondestructive measurement of mechanical strength properties of engineering materials is reviewed. Even where conventional NDE techniques have shown that a part is free of overt defects, advanced NDE techniques should be available to confirm the material properties assumed in the part's design. There are many instances where metallic, composite, or ceramic parts may be free of critical defects while still being susceptible to failure under design loads due to inadequate or degraded mechanical strength. This must be considered in any failure prevention scheme that relies on fracture analysis. This review will discuss the availability of ultrasonic methods that can be applied to actual parts to assess their potential susceptibility to failure under design conditions.

Vary, A.↗

NASA NTRS1984

Friction behavior of silicon in contact with titanium, nickel, silver and copper

Sliding friction experiments are conducted with the semiconductor silicon in contact with the metals titanium, nickel, copper, and silver. Sliding is on the (111) plane of single-crystal silicon in the 112 crystallographic direction both in dry and lubricated (mineral oil) sliding. The friction coefficient in dry sliding is controlled by adhesion and the surface chemical activity of the metal. The more active the metal the stronger the adhesion and the higher the friction. In lubricated sliding the lubricant absorbs to the surfaces and reduces the importance of metal chemical effects. In lubricated sliding, silicon ceases to behave in a brittle manner and undergoes plastic deformation under load.

Mishina, H.↗

NASA NTRS1984

Host turbine heat transfer overview

Improved methods of predicting airfoil local metal temperatures require advances in the understanding of the physics and methods of analytically predicting the following four aerothermal loads: hot gas flow over airfoils, heat transfer rates on the gas-side of airfoils, cooling air flow inside airfoils, and heat transfer rates on the coolant-side of airfoils. A systematic building block research approach is being pursued to investigate these four areas of concern from both the experimental and analytical sides. Experimental approaches being pursued start with fundamental experiments using simple shapes and flat plates in wind tunnels, progress to more realistic cold and hot cascade tests using airfoils, continue to progress in large low-speed rigs and turbines and warm turbines, and finally, combine all the interactive effects in tests using real engines or real engine type turbine rigs. Analytical approaches being pursued also build from relatively simple steady two dimensional inviscid flow and boundary layer heat transfer codes to more advanced steady two and three dimensional viscous flow and heat transfer codes. These advanced codes provide more physics to model better the interactive effects and the true real-engine environment.

Rohde, J. E.↗

NASA NTRS1986

Case histories involving fatigue and fracture mechanics; Proceedings of the Symposium, Charleston, SC, Mar. 21, 22, 1985

Papers are presented on cracking at nozzle corners in the nuclear pressure vessel industry, applied fracture mechanics for assessing defect significance in a crude oil pipeline, failure analysis of a large wind-tunnel compressor blade, analysis of a compressor-wheel failure, and preventing fracture by inspection and analysis. Consideration is also given to the fatigue crack growth predictions of welded aircraft structures containing flaws in the residual stress field, the fatigue and fracture mechanics analysis of a compression loaded aircraft structure, fracture of an aircraft horizontal stabilizer, fatigue life analysis of fuel tank skins under combined loads, and aircraft structural maintenance recommendations based on fracture mechanics analysis. Additional papers discuss an analysis of two metal-forming die failures, an analysis of a failed saw arbor, and the role of fracture mechanics in assessing the effect on fatigue life of design changes in welded fabrications.

Hudson, C. Michael↗