Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA ARC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

High Voltage Solar Array ARC Testing for a Direct Drive Hall Effect Thruster System

The deleterious effects of spacecraft charging are well known, particularly when the charging leads to arc events. The damage that results from arcing can severely reduce system lifetime and even cause critical system failures. On a primary spacecraft system such as a solar array, there is very little tolerance for arcing. Motivated by these concerns, an experimental investigation was undertaken to determine arc thresholds for a high voltage (200-500 V) solar array in a plasma environment. The investigation was in support of a NASA program to develop a Direct Drive Hall-Effect Thruster (112HET) system. By directly coupling the solar array to a Hall-effect thruster, the D2HET program seeks to reduce mass, cost and complexity commonly associated with the power processing in conventional power systems. In the investigation, multiple solar array technologies and configurations were tested. The cell samples were biased to a negative voltage, with an applied potential difference between them, to imitate possible scenarios in solar array strings that could lead to damaging arcs. The samples were tested in an environment that emulated a low-energy, HET-induced plasma. Short duration "trigger" arcs as well as long duration "sustained" arcs were generated. Typical current and voltage waveforms associated with the arc events are presented. Arc thresholds are also defined in terms of vo!tage, (current and power. The data will be used to propose a new, high-voltage (>300 V) solar array design for which the likelihood of damage from arcing is minimal.

Schneider, T.↗

High Voltage Solar Array Arc Testing for a Direct Drive Hall Effect Thruster System

The deleterious effects of spacecraft charging are well known, particularly when the charging leads to arc events. The damage that results from arcing can severely reduce system lifetime and even cause critical system failures. On a primary spacecraft system such as a solar array, there is very little tolerance for arcing. Motivated by these concerns, an experimental investigation was undertaken to determine arc thresholds for a high voltage (200-500 V) solar array in a plasma environment. The investigation was in support of a NASA program to develop a Direct Drive Hall-Effect Thruster (D2HET) system. By directly coupling the solar array to a Hall-effect thruster, the D2HET program seeks to reduce mass, cost and complexity commonly associated with the power processing in conventional power systems. In the investigation, multiple solar array technologies and configurations were tested. The cell samples were biased to a negative voltage, with an applied potential difference between them, to imitate possible scenarios in solar array strings that could lead to damaging arcs. The samples were tested in an environment that emulated a low-energy, HET-induced plasma. Short duration trigger arcs as well as long duration sustained arcs were generated. Typical current and voltage waveforms associated with the arc events are presented. Arc thresholds are also defined in terms of voltage, current and power. The data will be used to propose a new, high-voltage (greater than 300 V) solar array design for which the likelihood of damage from arcing is minimal.

Schneider, Todd↗

Alternatives to the ISS Plasma Contacting Units

A spacecraft in a high-density equatorial LEO plasma will float negative relative to the ambient plasma. Because of the electron collection of exposed conductors on its solar arrays, it may float negative by up to its array voltage. The floating potential depends on the relative areas of electron and ion collection of the spacecraft. Early estimates of the International Space Station (ISS) potential were about -140 V relative to the surrounding plasma, because of its 160 V solar array string voltage. Because of the possibility of arcing of ISS structures and astronaut EMUs (spacesuits) into the space plasma, Plasma Contacting Units (PCUs) were added to the ISS design, to reduce the highly negative floating potentials by emitting electrons (effectively increasing the ion collecting area). In addition to the now-operating ISS PCUs, safety rules require another independent arc-hazard control method. In this paper, I discuss alternatives to the ISS PCUs for keeping the ISS floating potential at values below the arc-thresholds of ISS and EMU surface materials. Advantages and disadvantages of all of the recline loss will be presented.

Ferguson, Dale C.↗

Development of a plasma generator for a long pulse ion source for neutral beam injectors

A plasma generator for a long pulse H{sup +}/D{sup +} ion source has been developed. The plasma generator was designed to produce 65 A H{sup +}/D{sup +} beams at an energy of 120 keV from an ion extraction area of 12 cm in width and 45 cm in length. Configuration of the plasma generator is a multi-cusp bucket type with SmCo permanent magnets. Dimension of a plasma chamber is 25 cm in width, 59 cm in length, and 32.5 cm in depth. The plasma generator was designed and fabricated at Japan Atomic Energy Agency. Source plasma generation and beam extraction tests for hydrogen coupling with an accelerator of the KSTAR ion source have been performed at the KSTAR neutral beam test stand under the agreement of Japan-Korea collaborative experiment. Spatial uniformity of the source plasma at the extraction region was measured using Langmuir probes and {+-}7% of the deviation from an averaged ion saturation current density was obtained. A long pulse test of the plasma generation up to 200 s with an arc discharge power of 70 kW has been successfully demonstrated. The arc discharge power satisfies the requirement of the beam production for the KSTAR NBI. A 70 keV, 41 A, 5 s hydrogen ion beam has been extracted with a high arc efficiency of 0.9 -1.1 A/kW at a beam extraction experiment. A deuteron yield of 77% was measured even at a low beam current density of 73 mA/cm{sup 2}.

43 PARTICLE ACCELERATORS↗

Design and Development of High Voltage Direct Current (DC) Sources for the Solar Array Module Plasma Interaction Experiment

Two programmable, high voltage DC power supplies were developed as part of the flight electronics for the Solar Array Module Plasma Interaction Experiment (SAMPIE). SAMPIE's primary objectives were to study and characterize the high voltage arcing and parasitic current losses of various solar cells and metal samples within the space plasma of low earth orbit (LEO). High voltage arcing can cause large discontinuous changes in spacecraft potential which lead to damage of the power system materials and significant Electromagnetic Interference (EMI). Parasitic currents cause a change in floating potential which lead to reduced power efficiency. These primary SAMPIE objectives were accomplished by applying artificial biases across test samples over a voltage range from -600 VDC to +300 VDC. This paper chronicles the design, final development, and test of the two programmable high voltage sources for SAMPIE. The technical challenges to the design for these power supplies included vacuum, space plasma effects, thermal protection, Shuttle vibrations and accelerations.

Bibyk, Irene K.↗

Voyager 1 Planetary Radio Astronomy Observations Near Jupiter

Results are reported from the first low frequency radio receiver to be transported into the Jupiter magnetosphere. Dramatic new information was obtained both because Voyager was near or in Jupiter's radio emission sources and also because it was outside the relatively dense solar wind plasma of the inner solar system. Extensive radio arcs, from above 30 MHz to about 1 MHz, occurred in patterns correlated with planetary longitude. A newly discovered kilometric wavelength radio source may relate to the plasma torus near Io's orbit. In situ wave resonances near closest approach define an electron density profile along the Voyager trajectory and form the basis for a map of the torus. Studies in progress are outlined briefly.

Warwick, J. W.↗

Interaction of large, high power systems with operational orbit charged particle environments

Concepts are presently being advanced for space systems to be used for such activities as manufacturing, earth observations, scientific exploration, power generation and human habitation, in locations ranging from low earth orbit (300-500 km) to geosynchronous orbit and beyond. Many of these systems concepts envision large structures and high power levels, and consequently higher operating voltages than have been used in space to date. The potential impact of interactions of space systems with their operational orbit charged particle environments on the systems' performance must be accounted for in the design process. A potentially hazardous spacecraft-environment interaction is discussed, namely the interaction of large high voltage systems with low energy (less than 50 eV) plasmas which can result in loss of power, and/or arcing. The impact of this class of interactions on system operation is most severe at low orbits where the ambient plasmas are densest. Results of experimental work and predictions of simple analytical models are presented and their implications for design of space systems are discussed.

Purvis, C. K.↗

SAFE II: Large systems space plasma evaluation experiment

A shuttle flight experiment, the purpose of which is to obtain space data on the interaction of a high voltage solar array with the ambient space plasma is addressed. This flight experiment is a reflight of the solar array flight experiment, SAFE, except that three active solar array panels, electron release devices and plasma diagnostics are added. This experiment, SAFE 2, evaluates power loss due to parasitic current collected by the solar array, arcing on the solar array and perturbations to the plasma which may increase power loss and disturb plasma and charged particle science acquisition.

Carruth, M. R., Jr.↗

Thermodynamic properties and transport coefficients of air thermal plasmas mixed with ablated vapors of Cu and polytetrafluoroethylene

Because the fault arc in aircraft electrical system often causes a fire, it is particularly important to analyze its energy and transfer for aircraft safety. The calculation of arc energy requires the basic parameters of the arc. This paper is mainly devoted to the calculations of equilibrium composition, thermodynamic properties (density, molar weight, enthalpy, and specific heat at constant pressure) and transport coefficients (thermal conductivity, electrical conductivity, and viscosity) of plasmas produced by a mixture of air, Cu, and polytetrafluoroethylene under the condition of local thermodynamic equilibrium. The equilibrium composition is determined by solving a system of equations around the number densities of each species. The thermodynamic properties are obtained according to the standard thermodynamic relationships. The transport coefficients are calculated using the Chapman-Enskog approximations. Results are presented in the temperature range from 3000 to 30 000 K for pressures of 0.08 and 0.1 MPa, respectively. The results are more accurate and are reliable reference data for theoretical analysis and computational simulation of the behavior of fault arc.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scattering-matrix arc detection on the JET ITER-like ICRH antenna

Operating Ion Cyclotron Resonance Heating (ICRH) antennas at high power density puts them at risk of arcing which reduces the coupled power to the plasma because the perturbed impedance match triggers the Voltage Standing Wave Ratio (VWSR) based generator trip system but even worse might damage the antenna beyond repair because of the the arc s localised energy deposition. New antennas are designed to operate in a load tolerant way which creates low impedance zones that are especially at risk since the existing VSWR protection systems are less sensitive to arcs in these areas. To protect these low impedance areas, a new arc protection system referred as Scattering Matrix Arc Detection (SMAD) was proposed. This paper describes the basic operating principle and implementation in hard- and software for the JET ITER-Like Antenna (ILA), with testbed and preliminary JET commissioning results.

43 PARTICLE ACCELERATORS↗

Effects of near-Earth stochastic acceleration and reflections of magnetotail ions on the formation of auroral arcs

Findings obtained from global kinetic simulations of magnetotail plasma are discussed. A region of strongly nonadiabatic ion acceleration (known as the 'wall' region) exists in the near earth tail and demarcates two very different regimes of ion motion: adiabatic and quasi-adiabatic. After convection through the wall, ion distributions rapidly become isotropized and thermalized. A strong enhancement of the cross tail current occurs on the tailward side of the wall. Comparison of numerical and adiabatic pressure profiles indicates that nonadiabatic processes operating in this region may contribute significantly to a pressure balance relief in the course of quasi-steady magnetospheric convection.

Ashour-Abdalla, Maha↗

A flowing plasma model to describe drift waves in a cylindrical helicon discharge

A two-fluid model developed originally to describe wave oscillations in the vacuum arc centrifuge, a cylindrical, rapidly rotating, low temperature, and confined plasma column, is applied to interpret plasma oscillations in a RF generated linear magnetized plasma [WOMBAT (waves on magnetized beams and turbulence)], with similar density and field strength. Compared to typical centrifuge plasmas, WOMBAT plasmas have slower normalized rotation frequency, lower temperature, and lower axial velocity. Despite these differences, the two-fluid model provides a consistent description of the WOMBAT plasma configuration and yields qualitative agreement between measured and predicted wave oscillation frequencies with axial field strength. In addition, the radial profile of the density perturbation predicted by this model is consistent with the data. Parameter scans show that the dispersion curve is sensitive to the axial field strength and the electron temperature, and the dependence of oscillation frequency with electron temperature matches the experiment. These results consolidate earlier claims that the density and floating potential oscillations are a resistive drift mode, driven by the density gradient. To our knowledge, this is the first detailed physics model of flowing plasmas in the diffusion region away from the RF source. Possible extensions to the model, including temperature nonuniformity and magnetic field oscillations, are also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental breakdown of selected anodized aluminum samples in dilute plasmas

Anodized aluminum samples representative of Space Station Freedom structural material were tested for electrical breakdown under space plasma conditions. In space, this potential arises across the insulating anodized coating when the spacecraft structure is driven to a negative bias relative to the external plasma potential due to plasma-surface interaction phenomena. For anodized materials used in the tests, it was found that breakdown voltage varied from 100 to 2000 volts depending on the sample. The current in the arcs depended on the sample, the capacitor, and the voltage. The level of the arc currents varied from 60 to 1000 amperes. The plasma number density varied from 3 x 10 exp 6 to 10 exp 3 ions per cc. The time between arcs increased as the number density was lowered. Corona testing of anodized samples revealed that samples with higher corona inception voltage had higher arcing inception voltages. From this it is concluded that corona testing may provide a method of screening the samples.

Grier, Norman T.↗

Discharge characteristics of an atmospheric-pressure argon plasma column generated with a single-electrode configuration

An atmospheric-pressure argon discharge plasma column is generated by making use of a single-electrode configuration with the power supply operating at a frequency of 45 kHz. It is observed that corona, glowlike plume, and filamentary discharges evolve individually with increasing applied voltage. It is in the filamentary state with average electron density of order 10{sup 12} cm{sup -3} that plasma column grows up in the tube with increasing applied voltage. Its discharge characteristics are determined by measuring electrical parameters (voltage, conduction current, and average absorbed power) and optical emission spectroscopy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A snapshot of high-entropy alloy processing techniques and their effects on resulting mechanical properties

High-entropy alloys (HEAs) exhibit exceptional strength, corrosion resistance, and thermal stability, making them promising candidates for nuclear, aerospace, and other extreme applications. While most prior work has focused on compositional design, manufacturing techniques themselves can alter microstructure and mechanical properties as dramatically as alloy chemistry. This review compiles and compares the effects of processing routes—including arc melting, induction melting, mechanical alloying with spark plasma sintering, and additive manufacturing—on the structure and properties of HEAs. Quantitative comparisons highlight, for example, that SPS-processed alloys can achieve ∼20–45 % higher yield and tensile strength than arc-melted counterparts, while Bridgman solidification produces nearly single-crystal structures with elongation to failure exceeding 80 %. Additive manufacturing routes such as selective laser melting offer fine microstructures but also introduce anisotropy and porosity, leading to yield strengths spanning 100–600 MPa for the same composition. By synthesizing such results, this review provides actionable insight into how processing routes interact with HEA core effects (high entropy, lattice distortion, sluggish diffusion, and cocktail effect) to determine performance, thereby offering a practical guide for optimizing manufacturing strategies.

36 MATERIALS SCIENCE↗