Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

High Fidelity Tomographic Density Reconstructions [Slides]

Pressed high explosives have small density variations associated with the pressing process, from a few to sub percent depending on the material. Variations at these levels are known to have an impact on HE performance. Currently, a destructive testing method based on physical sectioning followed by immersion density measurements (slice and dice) is utilized. However, this method has poor spatial resolution limited by the the sectioning size, 1-2 cm. If possible, radiographic methods including Computed Tomography (CT) would be preferred, as they are non-destructive and have higher (less than .1 mm) spatial resolution. However, beam hardening, scattered radiation, and detector effects make density reconstructions at this level extremely challenging.

42 ENGINEERING↗

Dimensional stability of low-cost thermoplastic composite molds

This report addresses a key question for using additively manufactured tooling from carbon fiber reinforced thermoplastic composites. How does the distortion of the molded part change with the print orientation used in the manufacture of tooling? The objective of this research was to discuss the distortion of parts molded with such tooling, in relation to the deflections in the tooling during the compression molding process. This was achieved through both model simulations and experimental molding runs. A vertical orientation was used in printing the mold with a distinctly non-planar surface: this orientation allowed for higher performance along the press closing direction -- higher thermal conductivity, higher stiffness, and lower coefficient of thermal expansion. Epoxy-carbon fiber twill weave fabric prepreg was then compression molded in this mold. The thermomechanical properties of the tooling material and the molded part were measured and used in simulation of mold deformation as well as part distortion. The thermomechanical anisotropy of the mold is quite different from that of the molded part because in the mold, the stiffest direction is the z-axis, while in the molded thermoset part, the z-axis is the weakest direction. The connection between mold deformation during the compression molding process and the final part distortion can be seen from the simulation results. The simulation results for the case where the mold was four times as stiff as the part along the press closing direction compared well with experiment. When the mold stiffness was lowered in relation to the part stiffness, the mold deformation during the compression molding increased; but this led to a smaller extent of part distortion.

36 MATERIALS SCIENCE↗

Mo-100 Disk Structural Integrity Tests I

The NorthStar pressed and sintered 29 mm diameter, 0.5 mm thick Mo-100 disks will be subjected to large temperature gradients when in beam during production. The beam preferentially heats the disk center, while the aggressive cooling by the helium keeps areas outside the beam spot relatively cool. The result is a temperature gradient of up to 900°C over the radial distance of 14.5 mm. To test the disk integrity with this high temperature gradient, a special holder for a single disk was made such that proper cooling can be applied as in the design target and the disk heating can be replicated with induction heating. NorthStar press and sintered disks were used for these tests.

36 MATERIALS SCIENCE↗

Adrian Portales Coop Internship Report

Using the thesis of W.R. Nolan (cite) as a guide, Cobalt Iron (CoFe) powders were reacted with 0.1 wt.% and 0.2 wt.% phosphoric acid in a 20:1 ratio of acetone to phosphoric acid. The powders were then dried at room temperature. The resulting phosphate coated CoFe was then mixed with 0.75 wt.% of the lubricant N,N' ethylene bis-stearamide (trade name: Acrawax C) and hot pressed to form a consolidated soft magnetic material referred to as CoFeP. With an avenue of synthesis for CoFeP determined, a proper amount of stock was synthesized for continuous “brick” production. While under current optimization, these 1x1 mm magnetic bricks will ultimately be placed and secured along the inside wall of each MK Magnetics transformer core by an appropriate CoFeP dispersed epoxy. As of now each brick has been produced though a pressing and annealing process via square 2x2 cm die. Before a brick is made a pressure calculation is run to ensure the dies maximum operating pressure is not exceeded. Figure 1. ensures the user’s safety by showing that the tons-on-ram required for a 2x2 cm square die to reach 760 MPa is below the point of die failure.

36 MATERIALS SCIENCE↗

Impact Report: Quantum Systems Accelerator

The Quantum Systems Accelerator (QSA) is a U.S. National Quantum Information Science Research Center established in August 2020 and funded by the Department of Energy (DOE) Office of Science. QSA is composed of 15 partner institutions— universities and national laboratories—bringing together pioneers of many of today’s unique quantum information science (QIS) and engineering capabilities. Led by Lawrence Berkeley National Laboratory (Berkeley Lab), with Sandia National Laboratories (Sandia Labs) as the lead partner, 250+ QSA researchers are catalyzing U.S. leadership in a fast-growing field that seeks solutions to the Nation’s and the world’s most pressing problems by harnessing the laws of quantum mechanics.

97 MATHEMATICS AND COMPUTING↗

Advanced Mixed-Mode Pixel Array Detector for X-rays Above 20 keV (Final Report)

The objective of the work reported upon was to perform research and development and test advanced prototype imaging x-ray detectors needed to meet pressing scientific research needs at U.S. x-ray synchrotron user facilities. The high x-ray brightness of the Nation’s x-ray synchrotron sources in the DOE National Laboratories holds promise to advance science and technology in a broad range of fundamental and applied disciplines, including physics, chemistry, biomedical areas and engineering. At present, progress in many areas is being limited not by the x-ray source but by the lack of imaging x-ray detectors capable of meeting experimental needs. Specifically, there is pressing need for imaging detectors with high dynamic range, low noise, high frame rates and the ability to capture x-ray images with x-rays of energy > 20 keV. This Final Technical Report summarizes progress made at Cornell University on novel integrating x-ray detectors that address these characteristics.

36 MATERIALS SCIENCE↗

Testing of Helium-Cooled Metal Molybdenum Disk Target

NorthStar Medical Radioisotopes LLC is planning to produce an important medical radioisotope, molybdenum-99 (Mo-99), through photonuclear reaction on molybdenum-100 (Mo-100). In this approach, molybdenum metal will be bombarded with a 40-MeV electron beam. Because enriched Mo-100 is expensive, it is desired to use as much beam power as possible to achieve maximum production yield and minimize target mass. This objective leads to very high beam power density (heat deposition in the target), which sets challenging requirements for cooling. Together with scientists at Los Alamos National Laboratory, a team at Argonne National Laboratory has developed and demonstrated a cooling approach using pressurized helium, which allows for efficient heat removal. One of the main challenges in this approach is the management of the heat load on the target window. The target window separates the high-pressure helium inside the target from the vacuum in the beamline, so it is constantly under stress from differential pressure. Also, the window is cooled only by the helium gas flowing on one side, making the window cooling even more challenging. High heat deposition in the target disks also imposes a strict requirement on performance of the helium cooling system and thickness of the target disks. The target disks are produced from metal powder via a press-and-sinter process. The resulting disks do not possess tensile strength as high as solid molybdenum and might not survive the vibration from the high-velocity helium coolant and high thermal stress from beam heating. An Argonne team of scientists performed a series of tests at Argonne’s Low Energy Accelerator Facility (LEAF) [3-7]. This report describes two series of tests for scale down production target designs that utilize full-scale 29 millimeters diameter, 0.75 mm thick press-and-sintered disks. We performed two thermal tests with different beam parameters and configurations of the disk laminations. We compared the results of the window temperature measurements and cooling system parameters obtained in the experiments with those predicted by analytical calculations and Computation Flow Dynamic (CFD) simulations. Results of the experiments and calculations are presented below.

36 MATERIALS SCIENCE↗

Advanced Fabrication Techniques of Metal Hydrides for Science and Technology Applications (Abbreviated Final Report)

Lithium Hydride (LiH) atomic properties make it an excellent candidate for thermal energy storage, hydrogen storage, and nuclear reactor technology. High Energy Density (HED) experiments on LiH at the National Ignition Facility (NIF) can also provide critical Equation of State (EOS) and Hugoniot data. Density requirements for LiH vary per application and therefore physical and structural requirements for LiH are non-uniform. Historical production of LiH relies on casting processesthat are limited by density and grain-size control, which leads to unfavorable machinable characteristics. LiH manufacturing is further hindered due to its chemical reactivity and propensity to readily react with moisture. This work aimed at exploring advanced fabrication techniques for LiH such as 1) uniaxial powder pressing methods and 2) laser powder bed fusion (L-PBF) additive manufacturing. Uniaxial powder compaction offers advantageous tailorable mechanical and physical properties via density control, and L-PBF can produce net-shaped complex parts with unique microstructure. Uniaxial pressing proved successful in readily producing LiH with density control.

36 MATERIALS SCIENCE↗

Advanced Fabrication Techniques of Metal Hydrides for Science and Technology Applications (Full Technical Report)

Lithium Hydride (LiH) atomic properties make it an excellent candidate for thermal energy storage, hydrogen storage, and nuclear reactor technology. High Energy Density (HED) experiments on LiH at the National Ignition Facility (NIF) can also provide critical Equation of State (EOS) and Hugoniot data. Density requirements for LiH vary per application and therefore physical and structural requirements for LiH are non-uniform. Historical production of LiH relies on casting processes that are limited by density and grain-size control, which leads to unfavorable machinable characteristics. LiH manufacturing is further hindered due to its chemical reactivity and propensity to readily react with moisture. This work aimed at exploring advanced fabrication techniques for LiH such as 1) uniaxial powder pressing methods and 2) laser powder bed fusion (L-PBF) additive manufacturing. Uniaxial powder compaction offers advantageous tailorable mechanical and physical properties via density control, and L-PBF can produce net-shaped complex parts with unique microstructure. Uniaxial pressing proved successful in readily producing LiH with density control.

36 MATERIALS SCIENCE↗

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗

National Energy Water Treatment & Speciation (NEWTS): A Water & Critical Mineral Database and Dashboard

The scarcity of water resources, the need for beneficial water reuse, and the challenges of wastewater treatment are becoming increasingly pressing in economic, social, and environmental domains. Addressing these concerns requires effective treatment strategies to manage wastewater streams and tackle environmental and economic issues. Furthermore, the recovery of critical minerals from the waste streams associated with energy production holds the promise of offsetting treatment costs and securing local sources of valuable minerals. However, relevant data on these waste streams are dispersed and challenging to locate. The process of ingesting such data into modeling software often involves multiple steps, requiring data restructuring to meet software-input requirements. The non-standardized reporting of water data makes data aggregation and reformatting a time-consuming process. Additionally, essential attributes necessary for modeling water treatment and mineral scale formation are frequently missing. Moreover, data gaps vary depending on the region of interest. Consequently, there is a pressing need for high-quality energy-water composition data that can be easily imported into water chemistry modeling software. To address this need, the National Energy Technology Laboratory has created the National Energy Water Treatment and Speciation (NEWTS) Database and Dashboard—a free online tool catering to community leaders and water researchers. NEWTS facilitates a comprehensive understanding of the composition of energy-related wastewater streams in the United States. The datasets provide detailed concentrations and speciation of major and minor aqueous compounds in energy-related wastewater streams, including power plant leachate, acid mine drainage, brackish water, and oil and gas produced water across the United States. Many of the aqueous species are critical minerals (Li, REEs) in high demand to modernize the world’s energy infrastructure. Many of the datasets also contain volumetric flow-rates needed to model the treatment and reuse scenarios in advanced aqueous chemistry software programs. The NEWTS Database and Dashboard offer public access to hitherto challenging-to-access datasets, presented in a standardized format that is tailored for easy input into aqueous chemistry modeling software. By performing the work needed to transform dispersed, disparate data sources into unified, model-ready datasets, NEWTS serves as an essential resource in advancing water treatment research and sustainable water resource management.

produced water management↗

Brazil disc Testing of LX-17-1

When considering alternate test methods for assessing the tensile performance of insensitive plastic bonded explosive (PBX) materials, Brazil disc tensile testing is attractive from several standpoints. First, compared to the traditional dog-bone shaped specimen normally used in the direct tensile test, the Brazil test specimen is considerably easier to produce. Second, the Brazil specimen is compact, with a low aspect ratio that allows it to be machined from a wide variety of pressed geometries. Assuming test results are consistent and interpretable, the method could open up possibilities for rapid assessment of ultimate tensile strengths, and might be especially attractive when a large number of samples are to be tested. The trade-off for specimen simplicity is, however, that interpretation of the results from Brazil tests is inherently far less intuitive, and more difficult, than is the case with traditional tensile testing, since the method involves complex stress loading. As a result, the derivation of what one hopes are equivalent tensile failure stresses from Brazil testing necessitates some fairly involved calculations, requiring parameters that are not always readily obtained. In addition to some significant uncertainties, the specimen geometry does not lend itself easily to the accommodation of traditional strain measurement devices such as extensometers. As a consequence, optical techniques such as digital image correlation (DIC) are preferred when stress-strain curves are needed. In this test series we performed a sequence of experiments using Brazil discs made from LX-17-1. Tests were performed on samples at two different scaled sizes: discs that were 0.5 inches in diameter and 0.25 inch thick, and discs that were 1 inch in diameter and a 0.5 inch thick. Each of the specimen sets was tested using matching, equivalently scaled test fixtures, each with anvils whose radii were 0.25% greater than their respective specimen radii. All specimens tested were machined from billet pressed material made from Holston #851009 (LLNL tag #C-329) LX-17-1 molding powder. Tests were performed at two temperatures, +23 °C and +50 °C, with three each test redundancies at each condition. Based on data from this set of experiments we hoped to provide preliminary answers to a number of questions, including: 1) Roughly, what is the level of scatter in the data? 2) Are results scale independent, at least within the limited range of specimen sizes tested? 3) Using a consistent set of parameters, can we use the equations given by Sato and Awaji1 to calculate peak tensile stresses that are nearly equivalent to those measured using traditional dog-bone tensile testing methods.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

UHT-CAMANCHE: Ultra-High Temperature Ceramic Additively Manufactured Compact Heat Exchangers

The conceptual basis for this project is the convergence of advanced ultra-high temperature ceramic materials and additive manufacturing technologies to produce compact ceramic heat exchangers with complex internal flow path geometries. Task areas were broadly divided into materials and manufacturing development, heat exchanger design, component testing, and techno-economic analysis. Technical challenges included the design and commissioning of new test facilities, improving feature resolution and deposition rate of ceramic additive manufacturing techniques, establishing process-structure-property relationships in additively manufactured ultra-high temperature ceramics, and assessing high temperature materials compatibility in CO 2 environments. The primary candidate material evaluated in this work is a composite comprising zirconium diboride (ZrB2) with 30 vol. % silicon carbide (SiC) which was selected based on its desirable combination of high temperature mechanical properties, high thermal and electrical conductivities, and oxidation resistance. High solids loaded ZrB2-SiC pastes suitable for extrusion-based additive manufacturing were developed for the first time as part of this work. Materials compatibility studies indicate this material oxidizes in CO 2 to form a protective borosilicate scale which transforms to pure silica above 1000°C. Parts made by additive manufacturing displayed enlarged grain sizes produced by pressureless sintering as compared to hot-press sintering. Increases in microstructural coarseness have outsized effect on oxidation performance up to 1400°C due to incomplete oxidation of coarse large diameter SiC particles resulting in lower amounts of silica that apparently inhibit protective scale formation. Additive manufacturing as a forming technique did not appear to significantly affect thermal conductivity, hardness, or elastic modulus, though flexural strength was reduced by half or more as compared to traditionally hot-pressed materials. This effect was attributed to the presence of strength-limiting flaws (ca. 40 microns in size) originating from extrudate inhomogeneities that could potentially be eliminated with further process improvements. Attempts to attain economies of scale for production of multi-kilowatt scale heat exchangers by ceramic additive manufacturing proved difficult. Lack of automation and a modest extrusion rate while retaining fine feature resolution made the overall process labor intensive and limited experimental throughput. A number of full-scale components were taken through post-process heat treatments including drying, binder burnout, and sintering; however, none survived without significant flaws or cracks. Therefore, no operational data from a newly installed heat exchanger test loop were able to be obtained during the performance period. Continued research and development is recommended to improve economic feasibility of ceramic additive manufacturing by standardizing the use of advanced sensors, artificial intelligence, and automation tools to reduce associated labor costs and accelerate production rates. The materials and manufacturing techniques demonstrated in this work are likely to find applications in defense and energy applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Enabling Bipolar Membrane Manufacturing Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗

Enabling Roll-to-Roll Manufacturing of Bipolar Membranes Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗

TREATABILITY TEST REPORT FOR THE REMOVAL OF CHROMIUM FROM GROUNDWATER AT 100-D AREA USING ELECTROCOAGULATION

The U.S. Department of Energy (DOE) has committed to accelerate cleanup of contaminated groundwater along the Columbia River. The current treatment approach was driven by a series of Interim Action Records of Decision (IAROD) issued in the mid-1990s. Part of the approach for acceleration involves increasing the rate of groundwater extraction for the chromium plume north of the 100-D Reactor and injecting the treated water in strategic locations to hydraulically direct contaminated groundwater toward the extraction wells. The current treatment system uses ion exchange for Cr(VI) removal, with off-site regeneration of the ion exchange resins. Higher flow rates will increase the cost and frequency of ion exchange resin regeneration; therefore, alternative technologies are being considered for treatment at high flow rates. One of these technologies, electrocoagulation (EC), was evaluated through a pilot-scale treatability test. The primary purpose of the treatability study was to determine the effectiveness of Cr(VI) removal and the robustness/implementability of an EC system. Secondary purposes of the study were to gather information about derivative wastes and to obtain data applicable to scaling the process from the treatability scale to full-scale. The treatability study work plan identified a performance objective and four operational objectives. The performance objective for the treatability study was to determine the efficiency (effectiveness) of hexavalent chromium removal from the groundwater, with a desired concentration of {le} 20 micrograms per liter ({micro}g/L) Cr(VI) in the effluent prior to re-injection. Influent and effluent total chromium and hexavalent chromium data were collected using a field test kit for multiple samples per week, and from off-site laboratory analysis of samples collected approximately monthly. These data met all data quality requirements. Two of three effluent chromium samples analyzed in the off-site (that is, fixed) laboratory met the performance objective during the continuous operational testing. Effluent hexavalent chromium analyzed by the field laboratory met the performance goal in over 90 percent of the samples. All effluent hexavalent chromium samples during the batch testing with high influent hexavalent chromium concentrations ({approx}2000 {micro}g/L) met the performance objective. Although the EC system was able to meet the performance goal, it must be noted that it was not uncommon for the system to be operated in recycle mode to achieve the performance goal. The EC unit was sometimes, but not always, capable of a single pass treatment efficiency high enough to meet the performance goal, and recycling water for multiple treatment passes was effective. An operational objective was to determine the volume and composition of the waste streams to enable proper waste designation. The toxicity characteristic leaching procedure (TCLP) concentrations, pH, and free liquids were determined for solid material from the EC electrodes (mechanically removed scale), the filter press, and the tank bottoms for the effluent and waste collector tanks. These data met all data quality requirements. All solid-phase secondary waste streams were found to be below the TCLP limits for the toxicity characteristic, and a pH value within the limits for the corrosivity characteristic. Out of three samples, two (one of scale from the EC unit and one from filter press solids) failed the free liquid (paint filter) test, which is one of the acceptability criteria for Hanford's Environmental Restoration Disposal Facility (ERDF). The solid-phase waste generation rate was about 0.65-gallon of solid waste per 100 gallons of water treated. It is concluded that the solid-phase secondary waste generated from this technology under the conditions at the test site will meet the toxicity and corrosivity criteria for disposal. It is also concluded that with engineering and/or operational improvements, a solid-phase secondary waste could be produced that would meet the free liquid disposal requirements. The second operational objective was to assess the operational reliability and safety of the system. For the continuous operations testing period from July 23 to September 12,2007, the system was not able to operate unattended. An extensive period of startup and adjustment preceded continuous operations, but was unsuccessful in providing a suitable and robust operating condition. Primary operational reliability problems were related to the sensitivity of the solid separation process to operational conditions such that a robust operating procedure (for example, chemical dosage) was not identified during the treatability test. Poor solids separation and high effluent iron concentrations also led to operational difficulties associated with injection well fouling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Jack Rabbit Pretest Shadowplate Drawings For TATB IHE Model Development

The Jack Rabbit Pretest (PT) series consisted of 5 focused hydrodynamic experiments 2021E PT3, PT4, PT5, PT6, and PT7. They were fired in March and April of 2008 at the Contained Firing Facility, Site 300, Lawrence Livermore National Laboratory, Livermore, California. These experiments measured deadzone formation and impulse gradients created during the detonation of TATB based insensitive high explosive. When setting up computer simulations of the Jack Rabbit Pretest series, the modeler or code developer can execute simulations with increasing degrees of refinement using detail found in the shadowplate design. The easiest way to get started is by treating the shadowplate in each experiment as a monolithic homogeneous piece of stainless steel. The simulation of detonation would begin as a point initiation below the center, bottom surface of the shadowplate. The detonation running through the ultrafine TATB booster can be simulated using program burn and then switched over to a reactive flow detonation model as the detonation front crosses the boundary into the main charge LX-17 IHE. A modeler wanting to further refine the simulation and progression of shock through the shadowplate can use the more detailed shadowplate design information presented in this document. The source drawings are included in Appendix A of this document. Their titles and drawing numbers are listed. Each experiment's shadowplate consists of two major components. A 303 stainless steel shape that defines the outer dimensions of shadowplate and a cylindrical 303 stainless steel detonator housing that is located in a closely machined pocket in the shape. The SIMPLE ASSY drawing accurately represents the dimensions of the outer shape, it's machined cylindrical pocket, and detonator body which is treated as a monolithic, homogeneous piece of stainless steel. The detonator body cross section shows an accurately dimensioned void where the slapper flyer barrel, LX-16 (pressed PETN) pellet, and pellet can flyer barrel are located. The FULL ASSY drawing accurately represents the dimensions of the outer shadowplate shape and it's machined pocket. The detonator dimensions and materials are detailed in cross section and exploded view. All diameters, thicknesses, and materials are called out in the drawing. You will notice that the detonator includes a multilayer slapper assembly with two layers of electrically insulating Kapton sandwiching the copper foil bridge circuit. The Kapton insulated circuit is sandwiched between two thin stainless steel sheets. This slapper assembly is secured to the detonator body with two screws. There is a 0.25 mm gap between the slapper assembly and the outer shadowplate shape. The stainless steel detonator body contains an off-center titanium wheel. This titanium wheel is secured to the detonator body with one screw and two pins to maintain position and orientation of the pellet can assembly in the center of the detonator body. The titanium wheel contains a tantalum/tungsten washer and pellet can assembly. The pellet can assembly consists of a pressed LX-16 initiator pellet contained in an extruded aluminum foil can. It may be useful for the modeler to include some of the details of the shadowplate and detonator design to further refine simulations of the Jack Rabbit Pretest experiments. These details may be relevant to the progression of shock originating from the PETN initiation pellet and ultrafine TATB booster that propagates through the shadowplate.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fast Dense Low cost Scintillator for Nuclear Physics

We have studied the morphology, transparency, and optical properties of SrHfO{sub 3}:Ce ceramics. Ceramics can be made transparent by carefully controlling the stoichiometry of the precursor powders. When fully dense, transparent samples can be obtained. Ceramics with a composition close to stoichiometry (Sr:Hf ~ 1) appear to show good transparency and a reasonable light yield several times that of BGO. The contact and distance transparency of ceramics hot-pressed at about 1450ºC is very good, but deteriorates at increasingly higher hot-press temperatures. If these ceramics can be produced in large quantities and sizes, at low cost, they may be of considerable interest for PET and CT.

99 GENERAL AND MISCELLANEOUS↗