Search NASA⌕ Search

SEARCH · Search NASA

Results for “Programming model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Spur, helical, and spiral bevel transmission life modeling

A computer program, TLIFE, which estimates the life, dynamic capacity, and reliability of aircraft transmissions, is presented. The program enables comparisons of transmission service life at the design stage for optimization. A variety of transmissions may be analyzed including: spur, helical, and spiral bevel reductions as well as series combinations of these reductions. The basic spur and helical reductions include: single mesh, compound, and parallel path plus revert star and planetary gear trains. A variety of straddle and overhung bearing configurations on the gear shafts are possible as is the use of a ring gear for the output. The spiral bevel reductions include single and dual input drives with arbitrary shaft angles. The program is written in FORTRAN 77 and has been executed both in the personal computer DOS environment and on UNIX workstations. The analysis may be performed in either the SI metric or the English inch system of units. The reliability and life analysis is based on the two-parameter Weibull distribution lives of the component gears and bearings. The program output file describes the overall transmission and each constituent transmission, its components, and their locations, capacities, and loads. Primary output is the dynamic capacity and 90-percent reliability and mean lives of the unit transmissions and the overall system which can be used to estimate service overhaul frequency requirements. Two examples are presented to illustrate the information available for single element and series transmissions.

Savage, Michael↗
NASA NTRS2019

Piloted Full-Motion Simulation with Simulink®

A recent experiment at NASA Ames Research Center’s Vertical Motion Simulator (VMS) successfully combined a real-time, human in-the-loop architecture with the flexibility of operating in the Simulink® graphical model-based engineering environment. The VMS is a large amplitude flight simulator designed to be adaptable to provide rapid integration and development of a wide variety of vehicles and support diverse aeronautical investigations. Math models are often programmed in Simulink. Typically, to run Simulink models in real time, they are converted to C code. However, the conversion and integration process can be time consuming and cumbersome. Thus, the VMS facility capabilities were expanded to allow a Simulink vehicle math model to run in the MathWorks’ MATLAB environment during a piloted full-motion simulation experiment. The MATLAB Simulink based approach to driving the VMS was found to decrease development time by allowing quick integration of math model changes and providing the ability to run the same version of the model on researcher’s desktop computers. This accomplishment demonstrated that the development ease of the graphical Simulink environment could be retained, while working within the real-time environment of the VMS architecture and maintaining the unique flexibility of the VMS.

hardware in-the-loop↗
NASA NTRS2019

Piloted Full-Motion Simulation in Simulink®

A recent experiment at NASA Ames Research Center’s Vertical Motion Simulator (VMS) successfully combined a real-time, human in-the-loop architecture with the flexibility of operating in the Simulink® graphical model-based engineering environment. The VMS is a large amplitude flight simulator designed to be adaptable to provide rapid integration and development of a wide variety of vehicles and support diverse aeronautical investigations. Math models are often programmed in Simulink. Typically, to run Simulink models in real time, they are converted to C code. However, the conversion and integration process can be time consuming and cumbersome. Thus, the VMS facility capabilities were expanded to allow a Simulink vehicle math model to run in the MathWorks’ MATLAB environment during a piloted full-motion simulation experiment. The MATLAB Simulink based approach to driving the VMS was found to decrease development time by allowing quick integration of math model changes and providing the ability to run the same version of the model on researcher’s desktop computers. This accomplishment demonstrated that the development ease of the graphical Simulink environment could be retained, while working within the real-time environment of the VMS architecture and maintaining the unique flexibility of the VMS.

Lewis, Emily K.↗
NASA NTRS1972

Development of a model of machine hand eye coordination and program specifications for a topological machine vision system

A unified approach to computer vision and manipulation is developed which is called choreographic vision. In the model, objects to be viewed by a projected robot in the Viking missions to Mars are seen as objects to be manipulated within choreographic contexts controlled by a multimoded remote, supervisory control system on Earth. A new theory of context relations is introduced as a basis for choreographic programming languages. A topological vision model is developed for recognizing objects by shape and contour. This model is integrated with a projected vision system consisting of a multiaperture image dissector TV camera and a ranging laser system. System program specifications integrate eye-hand coordination and topological vision functions and an aerospace multiprocessor implementation is described.

Source record↗
NASA NTRS2007

Predicting Rocket or Jet Noise in Real Time

A semi-empirical theoretical model and a C++ computer program that implements the model have been developed for use in predicting the noise generated by a rocket or jet engine. The computer program, entitled the Realtime Rocket and Jet Engine Noise Analysis and Prediction Software, is one of two main subsystems of the Acoustic Prediction/Measurement Tool, which comprises software, acoustic instrumentation, and electronic hardware combined to afford integrated capabilities for real-time prediction and measurement of noise emitted by rocket and jet engines. [The other main subsystem, consisting largely of acoustic instrumentation and electronic hardware, is described in Wireless Acoustic Measurement System, which appears elsewhere in this section.] The theoretical model was derived from the fundamental laws of fluid mechanics, as first was done by M. J. Lighthill in his now famous theory of aerodynamically generated sound. The far-field approximation of the Lighthill theory is incorporated into this model. Many other contributions from various researchers have also been introduced into the model. The model accounts for two noise components: shear noise and self noise. The final result of the model is expressed in terms of a volume integral of the acoustic intensities attributable to these two components, subject to various directivity coefficients. The computer program was written to solve the volume integral. The inputs required by the program are two data files from a computational fluid dynamics (CFD) simulation of the flow of interest: the computational-grid file and the solution file. The CFD solution should be one that has been obtained for conditions that closely approximate those of an experimental test that is yet to be performed. In the current state of development of the model and software, it is recommended that the observation points lie along a radius at an angle >60 from the jet axis. The software provides, and is driven via, a graphical user interface, which facilitates its use. Optionally, the program accepts additional input in the form of data on the measured sound pressure level as a function of frequency at a given far-field location, preferably at an angle of 90 from the jet axis. The user is prompted to use default empirical constants or to choose constants based the measurement data. The user can view the results and compare them with other computational or experimental data. Once satisfied with the results, the user can save a graph of the results in a file that can be imported into documents.

Frendi, Kader↗
NASA NTRS1982

Remote Sensing/gis Integration for Site Planning and Resource Management

The development of an interactive/batch gridded information system (array of cells georeferenced to USGS quad sheets) and interfacing application programs (e.g., hydrologic models) is discussed. This system allows non-programer users to request any data set(s) stored in the data base by inputing any random polygon's (watershed, political zone) boundary points. The data base information contained within this polygon can be used to produce maps, statistics, and define model parameters for the area. Present/proposed conditions for the area may be compared by inputing future usage (land cover, soils, slope, etc.). This system, known as the Hydrologic Analysis Program (HAP), is especially effective in the real time analysis of proposed land cover changes on runoff hydrographs and graphics/statistics resource inventories of random study area/watersheds.

Fellows, J. D.↗
NASA NTRS1989

Analysis of an algae-based CELSS. Part 1: model development

A steady state chemical model and computer program have been developed for a life support system and applied to trade-off studies. The model is based on human demand for food and oxygen determined from crew metabolic needs. The model includes modules for water recycle, waste treatment, CO2 removal and treatment, and food production. The computer program calculates rates of use and material balance for food. O2, the recycle of human waste and trash, H2O, N2, and food production supply. A simple non-iterative solution for the model has been developed using the steady state rate equations for the chemical reactions. The model and program have been used in system sizing and subsystem trade-off studies of a partially closed life support system.

Models, Chemical↗
NASA NTRS2003

Software Searches for Better Spacecraft-Navigation Models

ADAPT is a computer program that searches for better mathematical models for spacecraft navigation. The task of tuning trajectory-determination models for interplanetary navigation is complex, requiring an intensive search of multiple dynamical and nondynamical models that yield trajectory solutions with minimal errors. By automating the search, ADAPT eases the task of human analysts and enables them to consider wider ranges of potential solutions. ADAPT uses genetic algorithms to search a range of relevant parameters in a user-selected design space to arrive at values for those parameters that best fit the measured spacecraft-tracking data. The user s guide for ADAPT reviews the theoretical basis of the program and presents two example applications. One example is that of selecting a solar-radiation model for the Mars Pathfinder (MPF) mission using MPF tracking data and an extended Kalman filter from prior spacecraft-navigation software. The second example is of the use of tracking data from the Stardust spacecraft mission combined with a pseudo-epoch-state batch filter and an empirical small-forces model to find improved impulse models for use during Stardust attitude adjustments.

Ely, Todd↗
NASA NTRS2018

SLS Navigation Model-Based Design Approach

The SLS Program chose to implement a Model-based Design and Model-based Requirements approach for managing component design information and system requirements. This approach differs from previous large-scale design efforts at Marshall Space Flight Center where design documentation alone conveyed information required for vehicle design and analysis and where extensive requirements sets were used to scope and constrain the design. The SLS Navigation Team has been responsible for the Program-controlled Design Math Models (DMMs) which describe and represent the performance of the Inertial Navigation System (INS) and the Rate Gyro Assemblies (RGAs) used by Guidance, Navigation, and Controls (GN&C). The SLS Navigation Team is also responsible for the navigation algorithms. The navigation algorithms are delivered for implementation on the flight hardware as a DMM. For the SLS Block 1-B design, the additional GPS Receiver hardware is managed as a DMM at the vehicle design level. This paper provides a discussion of the processes and methods used to engineer, design, and coordinate engineering trades and performance assessments using SLS practices as applied to the GN&C system, with a particular focus on the Navigation components. These include composing system requirements, requirements verification, model development, model verification and validation, and modeling and analysis approaches. The Model-based Design and Requirements approach does not reduce the effort associated with the design process versus previous processes used at Marshall Space Flight Center. Instead, the approach takes advantage of overlap between the requirements development and management process, and the design and analysis process by efficiently combining the control (i.e. the requirement) and the design mechanisms. The design mechanism is the representation of the component behavior and performance in design and analysis tools. The focus in the early design process shifts from the development and management of design requirements to the development of usable models, model requirements, and model verification and validation efforts. The models themselves are represented in C/C++ code and accompanying data files. Under the idealized process, potential ambiguity in specification is reduced because the model must be implementable versus a requirement which is not necessarily subject to this constraint. Further, the models are shown to emulate the hardware during validation. For models developed by the Navigation Team, a common interface/standalone environment was developed. The common environment allows for easy implementation in design and analysis tools. Mechanisms such as unit test cases ensure implementation as the developer intended. The model verification and validation process provides a very high level of component design insight. The origin and implementation of the SLS variant of Model-based Design is described from the perspective of the SLS Navigation Team. The format of the models and the requirements are described. The Model-based Design approach has many benefits but is not without potential complications. Key lessons learned associated with the implementation of the Model Based Design approach and process from infancy to verification and certification are discussed

Oliver, T. Emerson↗
NASA NTRS1989

Analysis of an algae-based CELSS. I - Model development

A steady state chemical model and computer program have been developed for a life support system and applied to trade-off studies. The model is based on human demand for food and oxygen determined from crew metabolic needs. The model includes modules for water recycle, waste treatment, CO2 removal and treatment, and food production. The computer program calculates rates of use and material balance for food, O2, the recycle of human waste and trash, H2O, N2, and food production/supply. A simple noniterative solution for the model has been developed using the steady state rate equations for the chemical reactions. The model and program have been used in system sizing and subsystem trade-off studies of a partially closed life support system.

Holtzapple, Mark T.↗
NASA NTRS1998

F-Nets and Software Cabling: Deriving a Formal Model and Language for Portable Parallel Programming

Parallel programming is still being based upon antiquated sequence-based definitions of the terms "algorithm" and "computation", resulting in programs which are architecture dependent and difficult to design and analyze. By focusing on obstacles inherent in existing practice, a more portable model is derived here, which is then formalized into a model called Soviets which utilizes a combination of imperative and functional styles. This formalization suggests more general notions of algorithm and computation, as well as insights into the meaning of structured programming in a parallel setting. To illustrate how these principles can be applied, a very-high-level graphical architecture-independent parallel language, called Software Cabling, is described, with many of the features normally expected from today's computer languages (e.g. data abstraction, data parallelism, and object-based programming constructs).

DiNucci, David C.↗
NASA NTRS1994

National facilities study. Volume 3: Mission and requirements model report

The National Facility Study (NFS) was initiated in 1992 by Daniel S. Goldin, Administrator of NASA as an initiative to develop a comprehensive and integrated long-term plan for future facilities. The resulting, multi-agency NFS consisted of three Task Groups: Aeronautics, Space Operations, and Space Research and Development (R&D) Task Groups. A fourth group, the Engineering and Cost Analysis Task Group, was subsequently added to provide cross-cutting functions, such as assuring consistency in developing an inventory of space facilities. Space facilities decisions require an assessment of current and future needs. Therefore, the two task groups dealing with space developed a consistent model of future space mission programs, operations and R&D. The model is a middle ground baseline constructed for NFS analytical purposes with excursions to cover potential space program strategies. The model includes three major sectors: DOD, civilian government, and commercial space. The model spans the next 30 years because of the long lead times associated with facilities development and usage. This document, Volume 3 of the final NFS report, is organized along the following lines: Executive Summary -- provides a summary view of the 30-year mission forecast and requirements baseline, an overview of excursions from that baseline that were studied, and organization of the report; Introduction -- provides discussions of the methodology used in this analysis; Baseline Model -- provides the mission and requirements model baseline developed for Space Operations and Space R&D analyses; Excursions from the baseline -- reviews the details of variations or 'excursions' that were developed to test the future program projections captured in the baseline; and a Glossary of Acronyms.

Source record↗
NASA NTRS2010

Animal Models and Bone Histomorphometry: Translational Research for the Human Research Program

This slide presentation reviews the use of animal models to research and inform bone morphology, in particular relating to human research in bone loss as a result of low gravity environments. Reasons for use of animal models as tools for human research programs include: time-efficient, cost-effective, invasive measures, and predictability as some model are predictive for drug effects.

Sibonga, Jean D.↗
NASA NTRS2024

A Survey of Modeling Activities by NASA’s Orbital Debris Program Office

NASA’s Orbital Debris Program Office (ODPO) develops and maintains a number of modeling tools to analyze and simulate the orbital debris environment. One of the most important products produced by the NASA ODPO is the Orbital Debris Engineering Model (ORDEM). This model can be used by satellite designers and operators to design missions for better protection against the debris environment. The ODPO is currently working on the next generation, designated ORDEM 4.0. ORDEM 4.0 will include many known features from previous models, such as the ability to input a spacecraft orbit and time and the ability to compute the flux as a function of debris size, impact speed, impact direction, and debris material densities, as well as uncertainty information on the flux. A new addition will be a parameterized debris shape model based on laboratory hypervelocity impact tests, including DebriSat. ORDEM is primarily based on dedicated debris measurements, such as by the Haystack Ultrawideband Satellite Imaging Radar (HUSIR), NASA’s Goldstone radar, and observations of geosynchronous orbits (GEO) using the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT). In addition to ORDEM, the ODPO also maintains other models, such as the LEO-to-GEO Environment Debris (LEGEND) model for studies of long-term evolution of Earth’s debris environment, with the ability to study various mitigation and remediation strategies. Another model, the Satellite Breakup Risk Assessment Model (SBRAM), is used to analyze how satellite breakups may affect critical space missions (such as the ISS) on short notice. In addition to these models, the ODPO maintains other secondary models used to model satellite explosions and collisions, analyze radar, optical, and in situ data, and to model such things as solar activity and orbit evolution. In this presentation, a survey of these models will be presented, showing how the different models are used together to create a comprehensive picture of Earth’s debris environment.

Mark Matney↗
NASA NTRS1995

Program Helps Generate Boundary-Element Mathematical Models

Composite Model Generation-Boundary Element Method (COM-GEN-BEM) computer program significantly reduces time and effort needed to construct boundary-element mathematical models of continuous-fiber composite materials at micro-mechanical (constituent) scale. Generates boundary-element models compatible with BEST-CMS boundary-element code for anlaysis of micromechanics of composite material. Written in PATRAN Command Language (PCL).

Goldberg, R. K.↗
NASA NTRS1985

Propeller aircraft interior noise model: User's manual for computer program

A computer program entitled PAIN (Propeller Aircraft Interior Noise) has been developed to permit calculation of the sound levels in the cabin of a propeller-driven airplane. The fuselage is modeled as a cylinder with a structurally integral floor, the cabin sidewall and floor being stiffened by ring frames, stringers and floor beams of arbitrary configurations. The cabin interior is covered with acoustic treatment and trim. The propeller noise consists of a series of tones at harmonics of the blade passage frequency. Input data required by the program include the mechanical and acoustical properties of the fuselage structure and sidewall trim. Also, the precise propeller noise signature must be defined on a grid that lies in the fuselage skin. The propeller data are generated with a propeller noise prediction program such as the NASA Langley ANOPP program. The program PAIN permits the calculation of the space-average interior sound levels for the first ten harmonics of a propeller rotating alongside the fuselage. User instructions for PAIN are given in the report. Development of the analytical model is presented in NASA CR 3813.

Wilby, E. G.↗