Search NASA⌕ Search

SEARCH · Search NASA

Results for “Random effect model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Pressure solution creep of random packs of spheres

Abstract We performed numerical calculations of compaction in aggregates of spherical grains, using Lehner and Leroy's (2004, hereinafter LL) constitutive model of pressure solution at grain contacts. That model is founded on a local definition of the thermodynamic driving force and leads to a fully coupled formulation of elastic deformation, dissolution, and diffusive transport along the grain boundaries. The initial geometry of the aggregate was generated by random packing of spheres with a small standard deviation of the diameters. During the simulations, isostatic loading was applied. The elastic displacements at the contacts were calculated according to Digby's (1981) nonlinear contact force model, and deformation by dissolution was evaluated using the LL formulation. The aggregate strain and porosity were tracked as a function of time for fixed temperature, applied effective pressure, and grain size. We also monitored values of the average and standard deviation of total load at each contact, the coordination number for packing, and the statistics of the contact dimensions. Because the simulations explicitly exclude processes such as fracturing, plastic flow, and transport owing to surface curvature, they can be used to test the influence of relative changes in the kinetics of dissolution and diffusion processes caused by contact growth and packing rearrangements. We found that the simulated strain data could be empirically fitted by two successive power laws of the form, ε x ∝ t ξ , where ξ was equal to 1 at very early times, but dropped to as low as 0.3 at longer times. The apparent sensitivity of strain rate to stress found in the simulations was much lower than predicted from constitutive laws that assume a single dominant process driven by average macroscopic loads. Likewise, the apparent activation enthalpy obtained from the simulated data was intermediate between that assumed for dissolution and diffusion, and, further, tended to decrease with time. These results are similar to the experimental observations of Visser et al.'s (2012), who used an aggregate geometry and physical conditions closely resembling the present numerical simulations.

Bernabé, Y.↗

Elucidating Primary Degradation Mechanisms in High-Cycling-Capacity, Compositionally Tunable High-Entropy Hydrides

The hydrogen sorption properties of single-phase bcc (TiVNb) 100–x Cr x alloys (x = 0–35) are reported. All alloys absorb hydrogen quickly at 25 °C, forming fcc hydrides with storage capacity depending on the Cr content. Here, a thermodynamic destabilization of the fcc hydride is observed with increasing Cr concentration, which agrees well with previous compositional machine learning models for metal hydride thermodynamics. The steric effect or repulsive interactions between Cr–H might be responsible for this behavior. The cycling performances of the TiVNbCr alloy show an initial decrease in capacity, which cannot be explained by a structural change. Pair distribution function analysis of the total X-ray scattering on the first and last cycled hydrides demonstrated an average random fcc structure without lattice distortion at short-range order. If the as-cast alloy contains a very low density of defects, the first hydrogen absorption introduces dislocations and vacancies that cumulate into small vacancy clusters, as revealed by positron annihilation spectroscopy. Finally, the main reason for the capacity drop seems to be due to dislocations formed during cycling, while the presence of vacancy clusters might be related to the lattice relaxation. Having identified the major contribution to the capacity loss, compositional modifications to the TiVNbCr system can now be explored that minimize defect formation and maximize material cycling performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A unified understanding of minimum lattice thermal conductivity

Here, we propose a first-principles model of minimum lattice thermal conductivity ($κ^{min}_L$) based on a unified theoretical treatment of thermal transport in crystals and glasses. We apply this model to thousands of inorganic compounds and find a universal behavior of $κ^{min}_L$ in crystals in the high-temperature limit: The isotropically averaged $κ^{min}_L$ is independent of structural complexity and bounded within a range from ~0.1 to ~2.6 W/(m K), in striking contrast to the conventional phonon gas model which predicts no lower bound. We unveil the underlying physics by showing that for a given parent compound, $κ^{min}_L$ is bounded from below by a value that is approximately insensitive to disorder, but the relative importance of different heat transport channels (phonon gas versus diffuson) depends strongly on the degree of disorder. Moreover, we propose that the diffuson-dominated $κ^{min}_L$ in complex and disordered compounds might be effectively approximated by the phonon gas model for an ordered compound by averaging out disorder and applying phonon unfolding. With these insights, we further bridge the knowledge gap between our model and the well-known Cahill–Watson–Pohl (CWP) model, rationalizing the successes and limitations of the CWP model in the absence of heat transfer mediated by diffusons. Finally, we construct graph network and random forest machine learning models to extend our predictions to all compounds within the Inorganic Crystal Structure Database (ICSD), which were validated against thermoelectric materials possessing experimentally measured ultralow κ L . Our work offers a unified understanding of $κ^{min}_L$, which can guide the rational engineering of materials to achieve .

42 ENGINEERING↗

Eternal inflation and localization on the landscape

We model essential features of eternal inflation on the landscape of a dense discretuum of vacua by the potential V({phi}) = V{sub 0}+{delta}V({phi}), where |{delta}V({phi})| << V{sub 0} is random. We find that the diffusion of the distribution function {rho}({phi},t) of the inflaton expectation value in different Hubble patches may be suppressed due to the effect analogous to the Anderson localization in disordered quantum systems. At late times only the localized part of the distribution function {rho}({phi},t) survives which leads to dynamical selection principle on the landscape. As a result, there exist such islands on the landscape that the probability to measure any but a small value of the cosmological constant in a given Hubble patch is exponentially suppressed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Survival of tumor and normal cells upon targeting with electron-emitting radionuclides

Purpose: Previous studies have shown that the mean absorbed dose to a tissue element may not be a suitable quantity for correlating with the biological response of cells in that tissue element. Cell survival can depend strongly on the distribution of radioactivity at the cellular and multicellular levels. Furthermore, when cellular absorbed doses are examined, the cross-dose from neighbor cells can be less radiotoxic than the self-dose component. To better understand how the nonuniformity of activity among cells can affect the dose response, a computer model of a 3D tissue culture was previously constructed and showed that activity distribution among cells is significantly more relevant than the mean absorbed dose for low-energy-electron emitters. The present work greatly expands upon those findings. Methods: In the present study, we used this same computer model but restricted the number of labeled cells to a fraction of the whole cell population (50%, 10%, and 1%, respectively). The labeled cells were randomly distributed among the whole cell population. Results: While the activity distribution is an important factor in determining the tissue response for low-energy-electron emitters, the fraction of labeled cells has an even more pronounced effect on survival response. For all electron energies studied, reducing the percentage of cells labeled significantly increases the surviving fraction of the whole population. Conclusions: This study provides abundant information on killing tumor and normal cells under some conditions relevant to targeted radionuclide therapy of isolated tumor cells and micrometastases. The percentage of cells labeled, activity distribution among the labeled cells, and electron energy play key roles in determining their response. Most importantly, and not previously demonstrated, lognormal activity distributions can have a profound impact on the response of the tumor cells even when the radionuclide emits high-energy electrons.

60 APPLIED LIFE SCIENCES↗

Computational experiments to characterize bubble formation and movement in waste glass foam layer

Computer simulation experiments are a valuable complement to physical experimentation for systems where there is limited access to quantities of interest. The motivation for this work is to characterize the fluid dynamic and heat transfer processes that affect melt rate of waste slurry during vitrification, which can limit the throughput rate of the melter. Heat transfer to the cold cap from the molten glass below this layer is an important factor determining melt rate. In this study, computational fluid dynamics is used to elucidate the behavior of gas-filled cavities that form underneath the cold cap in a laboratory-scale waste glass melter. The cold cap consists of a reacting feed layer above a foam layer. The cavities are a result of coalesced gases from collapsing primary foam and air from forced convection bubblers. Bubbles in the foam layer move horizontally with the circulation pattern of the melt and escape around the edges of the cold cap to the plenum above. The effects of varying thermophysical properties and foam parameters based on the bounds of high-level waste glass formulations were explored. Using the DAKOTA toolkit, a Latin hypercube space-filling design was used to randomly distribute samples in bins to achieve good coverage over the parameter space with minimal points. Using the results from the set of simulations, a Gaussian process model with a linear trend was used to create response surfaces for several key quantities of interest, including temperatures, temperature gradients, velocities, and foam extent beneath the cold cap.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Statistical studies of spinning black-hole binaries

We study the statistical distributions of the spins of generic black-hole binaries during the inspiral and merger, as well as the distributions of the remnant mass, spin, and recoil velocity. For the inspiral regime, we start with a random uniform distribution of spin directions S-vector{sub 1} and S-vector{sub 2} over the sphere and magnitudes |S-vector{sub 1}/m{sub 1}{sup 2}|=|S-vector{sub 2}/m{sub 2}{sup 2}|=0.97 for different mass ratios, where S-vector{sub i} and m{sub i} are the spin-angular momentum and mass of the ith black hole. Starting from a fiducial initial separation of R{sub i}=50M, we perform 3.5-post-Newtonian-order evolutions down to a separation of R{sub f}=5M, where M=m{sub 1}+m{sub 2}, the total mass of the system. At this final fiducial separation, we compute the angular distribution of the spins with respect to the final orbital angular momentum, L-vector. We perform 16{sup 4}=65 536 simulations for six mass ratios between q=1 and q=1/16 and compute the distribution of the angles L-vector{center_dot}{Delta}-vector and L-vector{center_dot}S-vector, directly related to recoil velocities and total angular momentum. We find a small but statistically significant bias of the distribution towards counteralignment of both scalar products. A post-Newtonian analysis shows that radiation-reaction-driven dissipative effects on the orbital angular momentum lead to this bias. To study the merger of black-hole binaries, we turn to full numerical techniques. In order to make use of the numerous simulations now available in the literature, we introduce empirical formulas to describe the final remnant black-hole mass, spin, and recoil velocity for merging black-hole binaries with arbitrary mass ratios and spins. Our formulas are based on the post-Newtonian scaling, to model the plunge phase, with amplitude parameters chosen by a least-squares fit of recently available fully nonlinear numerical simulations, supplemented by inspiral losses from infinity to the innermost stable circular orbit. We then evaluate those formulas for randomly chosen directions of the individual spins and magnitudes as well as the binary's mass ratio. The number of evaluations has been chosen such that there are 10 configurations per each dimension of this parameter space, i.e. 10{sup 7}. We found that the magnitude of the recoil velocity distribution decays exponentially as P(v){approx}exp(-v/2500 km s{sup -1}) with mean velocity <v>=630 km s{sup -1} and standard deviation {radical}(<v{sup 2}>-<v>{sup 2})=534 km s{sup -1}, leading to a 23% probability of recoils larger than 1000 km s{sup -1}, and a highly peaked angular distribution along the final orbital axis. The studies of the distribution of the final black-hole spin magnitude show a universal distribution highly peaked at S{sub f}/m{sub f}{sup 2}=0.73 and a 25 deg. misalignment with respect to the final orbital angular momentum, just prior to full merger of the holes. We also compute the statistical dependence of the magnitude of the recoil velocity with respect to the ejection angle. The spin and recoil velocity distributions are also displayed as a function of the mass ratio. Finally, we compute the effects of the observer orientation with respect to the recoil velocity vector to take into account the probabilities to measure a given redshifted (or blueshifted) radial velocity of accretion disks with respect to host galaxies.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Dietary mung bean protein reduces high-fat diet-induced weight gain by modulating host bile acid metabolism in a gut microbiota-dependent manner

Highlights: • Mung bean protein intake reduces high fat diet-induced weight gain, fat accumulation, and hepatic steatosis. . • Mung bean protein intake increases plasma GLP-1 and intestinal secondary bile acids. • The anti-obesity effects occur via a mechanism that depends on the gut microbiota. The 8-globulin-rich mung bean protein (MPI) suppresses hepatic lipogenesis in rodent models and reduces fasting plasma glucose and insulin levels in obese adults. However, its effects on mitigating high fat diet (HFD)-induced obesity and the mechanism underlying these effects remain to be elucidated. Herein, we examined the metabolic phenotype, intestinal bile acid (BA) pool, and gut microbiota of conventionally raised (CONV-R) male C57BL/6 mice and germ-free (GF) mice that were randomized to receive either regular HFD or HFD containing mung bean protein isolate (MPI) instead of the dairy protein present in regular HFD. MPI intake significantly reduced HFD-induced weight gain and adipose tissue accumulation, and attenuated hepatic steatosis. Enhancement in the secretion of intestinal glucagon-like peptide-1 (GLP-1) and an enlarged cecal and fecal BA pool of dramatically elevated secondary/primary BA ratio were observed in mice that had consumed MPI. These effects were abolished in GF mice, indicating that the effects were dependent upon the presence of the microbiota. As revealed by 16S rRNA gene sequence analysis, MPI intake also elicited dramatic changes in the gut microbiome, such as an expansion of taxa belonging to the phylum Bacteroidetes along with a reduced abundance of the Firmicutes.

60 APPLIED LIFE SCIENCES↗

Imaging Phase Segregation in Nanoscale Li x CoO 2 Single Particles

Li x CoO 2 (LCO) is a common battery cathode material that has recently emerged as a promising material for other applications including electrocatalysis and as electrochemical random access memory (ECRAM). During charge– discharge cycling LCO exhibits phase transformations that are significantly complicated by electron correlation. While the bulk phase diagram for an ensemble of battery particles has been studied extensively, it remains unclear how these phases scale to nanometer dimensions and the effects of strain and diffusional anisotropy at the single-particle scale. Understanding these effects is critical to modeling battery performance and for predicting the scalability and performance of electrocatalysts and ECRAM. Here we investigate isolated, epitaxial LiCoO 2 islands grown by pulsed laser deposition. After electrochemical cycling of the islands, conductive atomic force microscopy (c-AFM) is used to image the spatial distribution of conductive and insulating phases. Above 20 nm island thicknesses, we observe a kinetically arrested state in which the phase boundary is perpendicular to the Li-planes; we propose a model and present image analysis results that show smaller LCO islands have a higher conductive fraction than larger area islands, and the overall conductive fraction is consistent with the lithiation state. Thinner islands (14 nm), with a larger surface to volume ratio, are found to exhibit a striping pattern, which suggests surface energy can dominate below a critical dimension. When increasing force is applied through the AFM tip to strain the LCO islands, significant shifts in current flow are observed, and underlying mechanisms for this behavior are discussed. The c-AFM images are compared with photoemission electron microscopy images, which are used to acquire statistics across hundreds of particles. Finally, the results indicate that strain and morphology become more critical to electrochemical performance as particles approach nanometer dimensions.

25 ENERGY STORAGE↗

In Situ Localized Surface Plasmon Resonance (LSPR) Spectroscopy to Investigate Kinetics of Chemical Bath Deposition of CdS Thin Films

Techniques that can characterize the early stages of thin film deposition from liquid phase processes can aid greatly in our understanding of mechanistic aspects of chemical bath deposition (CBD). Here we have used localized surface plasmon resonance (LSPR) spectroscopy to monitor in-situ the kinetics of early-stage growth of cadmium sulfide (CdS) thin films on Ag nanoparticle on quartz substrates. Real-time shift during CdS deposition showed that the LSPR wavelength red shifted rapidly due to random deposition of CdS on the substrate, but saturated at longer times. LSPR modeling showed that these features could be interpreted as an initial deposition of CdS islands followed by preferential deposition onto itself. The CdS also showed significantly enhanced Raman signals up to 170 times due to surface enhanced raman scattering (SERS) from the CdS/Ag NP regions. The ex-situ SERS effect supported the LSPR shift suggesting that these techniques could be used to understand nucleation and growth phenomena from the liquid phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optical variability of AGNs in the PTF/iPTF survey

We characterize the optical variability of quasars in the Palomar Transient Factory and intermediate Palomar Transient Factory (PTF/iPTF) surveys. We re-calibrate the r-band light curves for ∼28,000 luminous, broad-line active galactic nuclei from the SDSS, producing a total of ∼2.4 million photometric data points. We utilize both the structure function (SF) and power spectrum density (PSD) formalisms to search for links between the optical variability and the physical parameters of the accreting supermassive black holes that power the quasars. The excess variance (SF{sup 2}) of the quasar sample tends to zero at very short time separations, validating our re-calibration of the time-series data. We find that the the amplitude of variability at a given time-interval, or equivalently the timescale of variability to reach a certain amplitude, is most strongly correlated with luminosity with weak or no dependence on black hole mass and redshift. For a variability level of SF(τ) = 0.07 mag, the timescale has a dependency of τ∝L{sup 0.4}. This is broadly consistent with the expectation from a simple Keplerian accretion disk model, which provides τ∝L{sup 0.5}. The PSD analysis also reveals that many quasar light curves are steeper than a damped random walk. We find a correlation between the steepness of the PSD slopes, specifically the fraction of slopes steeper than 2.5, and black hole mass, although we cannot exclude the possibility that luminosity or Eddington ratio are the drivers of this effect. This effect is also seen in the SF analysis of the (i)PTF data, and in a PSD analysis of quasars in the SDSS Stripe 82.

79 ASTRONOMY AND ASTROPHYSICS↗

APPLICATION OF JITTER RADIATION: GAMMA-RAY BURST PROMPT POLARIZATION

A high degree of polarization of gamma-ray burst (GRB) prompt emission has been confirmed in recent years. In this paper, we apply jitter radiation to study the polarization feature of GRB prompt emission. In our framework, relativistic electrons are accelerated by turbulent acceleration. Random and small-scale magnetic fields are generated by turbulence. We further determine that the polarization property of GRB prompt emission is governed by the configuration of the random and small-scale magnetic fields. A two-dimensional compressed slab, which contains a stochastic magnetic field, is applied in our model. If the jitter condition is satisfied, the electron deflection angle in the magnetic field is very small and the electron trajectory can be treated as a straight line. A high degree of polarization can be achieved when the angle between the line of sight and the slab plane is small. Moreover, micro-emitters with mini-jet structures are considered to be within a bulk GRB jet. The jet 'off-axis' effect is intensely sensitive to the observed polarization degree. We discuss the depolarization effect on GRB prompt emission and afterglow. We also speculate that the rapid variability of GRB prompt polarization may be correlated with the stochastic variability of the turbulent dynamo or the magnetic reconnection of plasmas.

79 ASTRONOMY AND ASTROPHYSICS↗

Dosimetry Modeling for Focal Low-Dose-Rate Prostate Brachytherapy

Purpose: Focal brachytherapy targeted to an individual lesion(s) within the prostate may reduce side effects experienced with whole-gland brachytherapy. The outcomes of a consensus meeting on focal prostate brachytherapy were used to investigate optimal dosimetry of focal low-dose-rate (LDR) prostate brachytherapy targeted using multiparametric magnetic resonance imaging (mp-MRI) and transperineal template prostate mapping (TPM) biopsy, including the effects of random and systematic seed displacements and interseed attenuation (ISA). Methods and Materials: Nine patients were selected according to clinical characteristics and concordance of TPM and mp-MRI. Retrospectively, 3 treatment plans were analyzed for each case: whole-gland (WG), hemi-gland (hemi), and ultra-focal (UF) plans, with 145-Gy prescription dose and identical dose constraints for each plan. Plan robustness to seed displacement and ISA were assessed using Monte Carlo simulations. Results: WG plans used a mean 28 needles and 81 seeds, hemi plans used 17 needles and 56 seeds, and UF plans used 12 needles and 25 seeds. Mean D90 (minimum dose received by 90% of the target) and V100 (percentage of the target that receives 100% dose) values were 181.3 Gy and 99.8% for the prostate in WG plans, 195.7 Gy and 97.8% for the hemi-prostate in hemi plans, and 218.3 Gy and 99.8% for the focal target in UF plans. Mean urethra D10 was 205.9 Gy, 191.4 Gy, and 92.4 Gy in WG, hemi, and UF plans, respectively. Mean rectum D2 cm{sup 3} was 107.5 Gy, 77.0 Gy, and 42.7 Gy in WG, hemi, and UF plans, respectively. Focal plans were more sensitive to seed displacement errors: random shifts with a standard deviation of 4 mm reduced mean target D90 by 14.0%, 20.5%, and 32.0% for WG, hemi, and UF plans, respectively. ISA has a similar impact on dose-volume histogram parameters for all plan types. Conclusions: Treatment planning for focal LDR brachytherapy is feasible. Dose constraints are easily met with a notable reduction to organs at risk. Treating smaller targets makes seed positioning more critical.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Solution-based thermodynamic modeling of the Ni-Al-Mo system using first-principles calculations

A solution-based thermodynamic description of the ternary Ni–Al–Mo system is developed here, incorporating first-principles calculations and reported modeling of the binary Ni–Al, Ni–Mo and Al–Mo systems. To search for the configurations with the lowest energies of the N phase, the Alloy Theoretic Automated Toolkit (ATAT) was employed and combined with VASP. The liquid, bcc and γ-fcc phases are modeled as random atomic solutions, and the γ'-Ni3Al phase is modeled by describing the ordering within the fcc structure using two sublattices, summarized as (Al,Mo,Ni)0.75(Al,Mo,Ni)0.25. Thus, γ-fcc and γ'-Ni3Al are modeled with a single Gibbs free energy function with appropriate treatment of the chemical ordering contribution. In addition, notable improvements are the following: first, the ternary effects of Mo and Al in the B2-NiAl and D0a-Ni3Mo phases, respectively, are considered; second, the N-NiAl8Mo3 phase is described as a solid solution using a three-sublattice model; third, the X-Ni14Al75Mo11 phase is treated as a stoichiometric compound. Model parameters are evaluated using first-principles calculations of zero-Kelvin formation enthalpies and reported experimental data. In comparison with the enthalpies of formation for the compounds ψ-AlMo, θ-Al8Mo3 and B2-NiAl, the first-principles results indicate that the N-NiAl8Mo3 phase, which is stable at high temperatures, decomposes into other phases at low temperature. Resulting phase equilibria are summarized in the form of isothermal sections and liquidus projections. To clearly identify the relationship between the γ-fcc and γ'-Ni3Al phases in the ternary Ni–Al–Mo system, the specific γ-fcc and γ'-Ni3Al phase fields are plotted in x(Al)–x(Mo)–T space for a temperature range 1200–1800 K.

36 MATERIALS SCIENCE↗

The effect of cell-size dispersity on the mechanical properties of closed-cell aluminum foam

Highlights: • The effect of cell-size dispersity on the Young’s modulus of foam was investigated through experiments and simulations • Crushing experiments were conducted on 27 foam specimens in order measure the relative Young’s modulus • Three types of numerical models, including monodispersed, bidispersed and polydispersed models were studied • The numerical convergence on the model size for different models was also studied • The difference among numerical results obtained from the three models was insignificant - Abstract: The mechanical properties of open-celled and closed-celled metallic foam are strongly influenced by the cellular microstructure and material properties of the base material from which the foam is made. The present study investigated the microstructure and mechanical properties of ALPORAS closed-cell Al foam. In particular, the effect of cell-size dispersity on the Young's modulus of foam was investigated through crushing experiments and numerical simulations. Crushing experiments were first conducted on two mutually perpendicular directions. Numerical models of varying cell-size dispersity and complexity were subsequently developed, including the monodispersed model that is based on the Kelvin structure, the bidispersed model, and the polydispersed model that is based on the random Laguerre tessellation algorithm. The numerical models were discretized using shell elements, and the simulations were conducted using the ABAQUS finite element method software. Relative Young's moduli with various relative densities were predicted, and the numerical convergence on the model size was studied accordingly. Numerical results obtained from all three numerical models developed were found to overestimate the experimental results by a factor of approximately 3. The difference between the numerical and experimental results can be attributed to the difference in detailed microstructural characteristics. Furthermore, the difference among numerical results obtained from the three models was insignificant.

36 MATERIALS SCIENCE↗

Backhopping effect in magnetic tunnel junctions: Comparison between theory and experiment

We report on magnetic switching and backhopping effects due to spin-transfer-torque in magnetic tunnel junctions. Experimental data on current-induced switching in junctions with a MgO tunnel barrier reveal random back-and-forth switching between magnetization states, which appears when the current direction favors the parallel magnetic configuration. The effect depends on the barrier thickness t{sub b} and is not observed in tunnel junctions with very thin MgO tunnel barriers, t{sub b} < 0.95 nm. The switching dependence on bias voltage and barrier thickness is explained in terms of the macrospin model, with the magnetization dynamics described by the modified Landau-Lifshitz-Gilbert equation. Numerical simulations indicate that the competition between in-plane and out-of-plane torque components can result in a non-deterministic switching behavior at high bias voltages, in agreement with experimental observations. When the barrier thickness is reduced, the overall coupling between the magnetic layers across the barrier becomes ferromagnetic, which suppresses the backhopping effect.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Far tails of the density of states in amorphous organic semiconductors

Far tails of the density of state (DOS) are calculated for the simple models of organic amorphous material, the model of dipolar glass and model of quadrupolar glass. It was found that in both models far tails are non-Gaussian. In the dipolar glass model, the DOS is symmetric around zero energy, while for the model of quadrupolar glass, the DOS is generally asymmetric and its asymmetry is directly related to the particular geometry of quadrupoles. Far tails of the DOS are relevant for the quasi-equilibrium transport of the charge carriers at low temperature. Asymmetry of DOS in quadrupolar glasses means a principal inequivalence of the random energy landscape for the transport of electrons and holes. Possible effect of the non-Gaussian shape of the far tails of the DOS on the temperature dependence of carrier drift mobility is discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

WE-G-18C-09: Separating Perfusion and Diffusion Components From Diffusion Weighted MRI of Rectum Tumors Based On Intravoxel Incoherent Motion (IVIM) Analysis

Purpose: Pseudodiffusion arises from the microcirculation of blood in the randomly oriented capillary network and contributes to the signal decay acquired using a multi-b value diffusion weighted (DW)-MRI sequence. This effect is more significant at low b-values and should be properly accounted for in apparent diffusion coefficient (ADC) calculations. The purpose of this study was to separate perfusion and diffusion component based on a biexponential and a segmented monoexponential model using IVIM analysis Methods. The signal attenuation is modeled as S(b) = S0[(1−f)exp(−bD) + fexp(−bD*)]. Fitting the biexponetial decay leads to the quantification of D, the true diffusion coefficient, D*, the pseudodiffusion coefficient, and f, the perfusion fraction. A nonlinear least squares fit and two segmented monoexponential models were used to derive the values for D, D*,‘and f. In the segmented approach b = 200 s/mm{sup 2} was used as the cut-off value for calculation of D. DW-MRI's of a rectum cancer patient were acquired before chemotherapy, before radiation therapy (RT), and 4 weeks into RT and were investigated as an example case. Results: Mean ADC for the tumor drawn on the DWI cases was 0.93, 1.0 and 1.13 10{sup −3}×mm{sup 2}/s before chemotherapy, before RT and 4 weeks into RT. The mean (D.10{sup −3} × mm{sup 2}/s, D* 10{sup −3} × mm{sup 2}/s, and f %) based on biexponential fit was (0.67, 18.6, and 27.2%), (0.72, 17.7, and 28.9%) and (0.83,15.1, and 30.7%) at these time points. The mean (D, D* f) based on segmented fit was (0.72, 10.5, and 12.1%), (0.72, 8.2, and 17.4%) and (.82, 8.1, 16.5%) Conclusion: ADC values are typically higher than true diffusion coefficients. For tumors with significant perfusion effect, ADC should be analyzed at higher b-values or separated from the perfusion component. Biexponential fit overestimates the perfusion fraction because of increased sensitivity to noise at low b-values.

60 APPLIED LIFE SCIENCES↗