SEARCH · Search NASA

Results for “Reference Model 2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

All sources NASA NTRS DOE OSTI

NASA NTRS2011

Handling Qualities of Model Reference Adaptive Controllers with Varying Complexity for Pitch-Roll Coupled Failures

Three model reference adaptive controllers (MRAC) with varying levels of complexity were evaluated on a high performance jet aircraft and compared along with a baseline nonlinear dynamic inversion controller. The handling qualities and performance of the controllers were examined during failure conditions that induce coupling between the pitch and roll axes. Results from flight tests showed with a roll to pitch input coupling failure, the handling qualities went from Level 2 with the baseline controller to Level 1 with the most complex MRAC tested. A failure scenario with the left stabilator frozen also showed improvement with the MRAC. Improvement in performance and handling qualities was generally seen as complexity was incrementally added; however, added complexity usually corresponds to increased verification and validation effort required for certification. The tradeoff between complexity and performance is thus important to a controls system designer when implementing an adaptive controller on an aircraft. This paper investigates this relation through flight testing of several controllers of vary complexity.

Schaefer, Jacob↗

DOE OSTI2020

Artificial Intelligence Application to D and D - 20492

As aging facilities across the DOE complex await decommissioning, there is an ongoing need to understand any changes in the structural conditions. Many of these facilities were built over 50 years ago and, in some cases, these facilities have gone beyond the expected operational lifetime. Many facilities have been placed in a state of 'cold and dark,' sitting unused and awaiting decommissioning. Especially challenging are the aging facilities that provide unique operational/production capabilities to support critical DOE missions and cannot be shut down. In any of these scenarios, the structural integrity of these facilities may become compromised as time passes. It is critical that adequate inspections be performed on a continual basis and that the data collected undergoes sufficient analysis to support timely identification of any new or worsening structural issues as well as prompt needed maintenance and repairs to maintain the facilities in a safe condition. In recent days, Artificial Intelligence (AI) [1] and its application to various domains are growing at fast speed. FIU is performing research in this area and exploring the associated technologies to solve nuclear decommissioning problems. Artificial intelligence refers to the capability of a program to autonomously act, react and adapt to the working environment. AI enables the machine to behave like humans and perform the cognitive functions such as 'learning' and 'problem solving'. AI systems gradually moving from traditional approaches (algorithms and expert systems) towards more efficient and advanced technologies (machine learning [1] and deep learning [2] [3]). AI is the study of algorithms and statistical models that is being used by computers to perform specific tasks without using explicit instructions. FIU is working to develop a pilot-scale infrastructure to implement structural health monitoring using AI technologies with focus on machine learning, deep learning. This research is focused on Computer Vision/Image Classification area of AI applications. This can also be expanded to other areas of AI related to Object Recognition and Character Recognition in images. In addition to utilizing existing data sets, FIU will collect and investigate image and video data using FIU test-bed mockups to monitor structural health of the facility. Resulting data will be processed and analyzed using machine learning/deep learning technologies. The proposed pilot system is intended to serve as a starting point to engage the DOE field sites on related data sets and their decision making needs. It is anticipated that proposed machine learning/deep learning technologies can be effectively employed using anomaly detection to solve EM challenges in surveillance and maintenance of the D and D facilities. FIU will work with research stakeholders to identify applications at various sites and other DOE facilities. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2019

Solar Resource Calibration, Measurement, and Dissemination: Final Report FY 2016-FY 2018

The Solar Resource Calibration, Measurement, and Dissemination project supports the U.S. Department of Energy's Solar Energy Technologies Office (SETO) initiative to make solar energy cost-competitive with other forms of electricity by improving the tools and methods to measure and model solar radiation and therefore reduce uncertainty in predicting solar output and improve the bankability of solar projects. This project has three tasks that conduct research on advancing solar resource measurements and modeling: Task 1: Applied solar Radiation Measurements. Task 2: National Solar Radiation Data Base (NSRDB). Task 3: Knowledge Sharing. The National Renewable Energy Laboratory's (NREL's) Solar Radiation Research Laboratory (SRRL) activities ensure traceable solar measurements throughout the United States that are essential for project feasibility, due diligence, financing, and plant operations. The SRRL houses NREL's Baseline Measurement System (BMS), which provides a platform for improving the accuracy of solar measurements through research to improve the calibration and characterization of instruments and enable the development of new measurement technology and standards. The platform contains a variety of instruments measuring solar radiation and other meteorological parameters. Following best practices, BMS instruments are calibrated to ensure traceability to the World Radiometric Reference in compliance with ISO/IEC 17025 accreditation requirements. The BMS data sets are quality-controlled and made publicly available through the Measurement and Instrumentation Data Center website. The NSRDB is the most accessed public database of solar irradiance and associated weather parameters for use in energy modeling. It supports SETO's goals of reducing barriers to high penetrations of solar technologies by providing easy access to high-quality, foundational data essential for innovative product development and downstream modeling through the NSRDB website. Data are currently available for the contiguous United States and beyond for 20 years covering 1998-2017. The Physical Solar Model (PSM) that underpins the current NSRDB data sets is a unique physics-based model that has been developed at NREL and has opened the door to the use of next-generation satellite data sets for solar resource assessment and forecasting. Through the American Society for Testing Materials (ASTM) International and other international standards organizations, NREL continues to provide leadership in the development of standards that are relevant to the measurement and modeling of solar radiation for solar energy applications. Standards developed cover the calibration method of pyrheliometers (direct normal irradiance measurements), pyranometers (global horizontal irradiance measurements), spectroradiometers, ultraviolet radiometers, correct field deployment of these instruments, spectral distribution reference tables for photovoltaic modeling, and transfer of indoor calibrations. Further, NREL leads the International Energy Agency (IEA) Photovoltaic Power Systems Programme Task 16: Subtask 1, which focuses on the evaluation of current and emerging resource assessment methodologies. NREL and the IEA updated the Best Practices Handbook for the Collection and Use of Solar Resource Data for Solar Energy Applications, which is widely used by the solar industry.

14 SOLAR ENERGY↗

DOE OSTI2018

Comment on ‘Does replacing coal with wood lower CO 2 emissions? Dynamic lifecycle analysis of wood bioenergy’

The use of wood for bioenergy production results in a worse climate outcome than from using coal. However, many of the assumptions on which their primary wood bioenergy scenario is based are not realistic and therefore are not informative. Assumptions of uncharacteristically long rotations for southern pine plantations, no utilization of wood for longer-duration products, and a single harvest over 100 years understate the carbon performance of current forest management practices. We provide references that support realistic modeling of forest carbon dynamics that are reflective of current practice and therefore more informative.

09 BIOMASS FUELS↗

DOE OSTI2020

Using an Absolute Cavity Pyrgeometer to Validate the Calibration of a Secondary Standard Pyrgeometer Outdoors, Independent from the Reference Value of the Atmospheric Longwave Irradiance

Accurate measurements of broadband outdoor longwave irradiance are important for renewable energy applications and the study of the atmosphere and climate change. A unique method of pyrgeometer calibration has been developed to improve the measurement uncertainty [1]. The results of this method yielded irradiance values within ±3 W/m 2 of those traceable to the World InfraRed Standard Group (WISG). This article describes a technique for validating this pyrgeometer calibration method using two Absolute Cavity Pyrgeometers (ACPs). The ACPs and pyrgeometer model PIR were deployed outdoors and the irradiance measured by the PIR was compared against the average irradiance measured by the two ACPs. The irradiance measured by the PIR was calculated using two equations, NREL equation and the Physikalisch Meteorologisches Observatorium Davos (PMOD) equation. The uncertainty with 95% confidence level ( U 95 ) of the irradiance measured by the PIR using NREL equation equaled ±3.51 W/m 2 with respect to SI and using PMOD equation U 95 equaled ±2.99 W/m 2 with respect to SI. These results suggest that the PIR calibration method might be useful in addressing the international need for a secondary standard pyrgeometer traceable to SI.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1986

Virtual space and 2-dimensional effects in perspective displays

When interpreting three dimensional spatial relationships presented on a two dimensional display surface, the viewer is required to mentally reconstruct the original information. This reconstruction is influenced by both the perspective geometry of the displayed image and the viewer's eye position relative to the display. In a study which manipulated these variables, subjects judged the azimuth direction of a target object relative to a reference object fixed in the center of a perspective display. The results support a previously developed model which predicted that the azimuth judgement error would be a sinusoidal function of stimulus azimuth. The amplitude of this function was correctly predicted to be systematically modulated by both the perspective geometry of the image and the viewer's eye position relative to the screen. Interaction of the two components of the model, the virtual space effect and the 3D-to-2D projection effect, predicted the relative amplitudes of the sinusoidal azimuth error functions for the various conditions of the experiment. Mean azimuth judgements in some directions differed by as much as 25 degrees as a result of different combinations of eye position and image geometry. The results illustrate the need to consider the effects of perspective geometry when designing spatial information instruments, and show the model to be a reliable predictor of average performance.

Mcgreevy, M. W.↗

DOE OSTI2024

Time-resolved quantification of key species and mechanistic insights in low-temperature tetrahydrofuran oxidation

Here, we investigate the kinetics and report the time-resolved concentrations of key chemical species in the oxidation of tetrahydrofuran (THF) at 7500 torr and 450–675 K. Experiments are carried out using high-pressure multiplexed photoionization mass spectrometry (MPIMS) combined with tunable vacuum ultraviolet radiation from the Berkely Lab Advanced Light Source. Intermediates and products are quantified using reference photoionization (PI) cross sections, when available, and constrained by a global carbon balance tracking approach at all experimental temperatures simultaneously for the species without reference cross sections. From carbon balancing, we determine time-resolved concentrations for the ROO˙ and ˙OOQOOH radical intermediates, butanedial, and the combined concentration of ketohydroperoxide (KHP) and unsaturated hydroperoxide (UHP) products stemming from the ˙QOOH + O 2 reaction. Furthermore, we quantify a product that we tentatively assign as fumaraldehyde, which arises from UHP decomposition via H 2 O or ˙OH + H loss. The experimentally derived species concentrations are compared with model predictions using the most recent literature THF oxidation mechanism of Fenard et al., (Combust. Flame, 2018, 191, 252–269). Our results indicate that the literature mechanism significantly overestimates THF consumption and the UHP + KHP concentration at our conditions. The model predictions are sensitive to the rate coefficient for the ROO˙ isomerization to ˙QOOH, which is the gateway for radical chain propagating and branching pathways. Comparisons with our recent results for cyclopentane (Demireva et al., Combust. Flame, 2023, 257, 112506) provide insights into the effect of the ether group on reactivity and highlight the need to determine accurate rate coefficients of ROO˙ isomerization and subsequent reactions.

Demireva, Maria↗

DOE OSTI2014

Dielectric relaxations and alternating current conductivity in manganese substituted cobalt ferrite

Manganese (Mn) substituted cobalt ferrites (CoFe{sub 2-x}Mn{sub x}O{sub 4}, referred to CFMO) have been synthesized by the solid state reaction method and their dielectric properties and ac conductivity have been evaluated as a function of applied frequency and temperature. X-ray diffraction measurements indicate that CFMO crystallize in the inverse cubic spinel phase with a lattice constant ∼8.38 Å. Frequency dependent dielectric measurements at room temperature obey the modified Debye model with relaxation time of 10{sup −4} s and spreading factor of 0.35(±0.05). The frequency (20 Hz–1 MHz) and temperature (T = 300–900 K) dependent dielectric constant analyses indicate that CFMO exhibit two dielectric relaxations at lower frequencies (1–10 kHz), while completely single dielectric relaxation for higher frequencies (100 kHz–1 MHz). The dielectric constant of CFMO is T-independent up to ∼400 K, at which point increasing trend prevails. The dielectric constant increase with T > 400 K is explained through impedance spectroscopy assuming a two-layer model, where low-resistive grains separated from each other by high-resistive grain boundaries. Following this model, the two electrical responses in impedance formalism are attributed to the grain and grain-boundary effects, respectively, which also satisfactorily accounts for the two dielectric relaxations. The capacitance of the bulk of the grain determined from impedance analyses is ∼10 pF, which remains constant with T, while the grain-boundary capacitance increases up to ∼3.5 nF with increasing T. The tan δ (loss tangent)-T also reveals the typical behavior of relaxation losses in CFMO.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Exotic edge states of C 3 high-fold fermions in honeycomb lattices

A generalization of the graphene honeycomb model to the case where each site in the honeycomb lattice contains a n -fold degenerate set of eigenstates of the C 3 symmetry has been recently proposed to describe several systems, including triangulene crystals and photonic lattices. These generalized honeycomb models are defined by ( n a , n b ) , the number of C 3 eigenstates in the a and b sites of the unit cell, resulting in n a + n b bands. Thus, the (1,1) case gives the coventional honeycomb model that describes the two low-energy bands in graphene. Generalizations, such as (2,1), (2,2), and (3,3) display several nontrivial features, such as coexisting graphenelike Dirac cones with flat bands, both at zero and finite energy, as well as robust degeneracy points where a flat band and a parabolic band meet at the Γ point. Here we explore the edge states of this class of crystals, using as reference triangulene crystals, and we find several types of edge states absent in the conventional (1,1) honeycomb case, associated to the nontrivial features of the two-dimensional bands of the high-fold case. First, we find dispersive edge states associated to the finite-energy flat bands, that occur both at the armchair and zigzag termination. Second, in the case of noncentrosymmetric triangulene crystals that lead to a S = 1 Dirac band, we have a bonding-antibonding pair of dispersive edge states, localized in the same edge so that their energy splitting is reduced as their localization increases, opposite to the conventional behavior of pairs of states localized in opposite edges. Third, for the (3,3) case, that hosts a gap separating a pair of flat conduction and valence bands, we find nondispersive edge states with E = 0 in all edge terminations. Published by the American Physical Society 2024

Madail, L. (ORCID:0000000208457748)↗

DOE OSTI2023

pnnl/projection_ntk

This is a repository for work conducted in our research paper we would like to make open source. The main features are that we forked another open source library and added functionality that enabled us to compute neural-kernel objects using random vector projection software for both computer vision and large language text models. The new features are specifically code that enables the calculation of objects we define and refer to as the projection pseudo neural tangent kernel and the projection trace neural tangent kernel; both of which are approximations of the empirical neural tangent kernel. The software that computes the projections themselves are not part of the invention, but are necessarily tied to our software and licensed via MIT license, and BSD 2 license.

Georgiev, Kristian↗

DOE OSTI2025

SSAPy - Space Situational Awareness for Python

SSAPy is a fast and flexible orbit modeling and analysis tool for orbits spanning from low-Earth into the cislunar regime. Orbits can be flexibly specified from common input formats such as Keplerian elements or two-line element (TLE) data files. SSAPy allows users to model satellites and specify parameters such as satellite area, mass, and drag coefficients. SSAPy includes a customizable force-propagation with a range of Earth, Lunar, radiation, atmospheric, and maneuvering models. SSAPy makes use of various community integration methods and can calculate time-evolved orbital quantities, including satellite magnitudes and state vectors. Users can specify various space- and ground-based observation models with support for multiple coordinate and reference frames. SSAPy also supports orbit analysis and propagation methods such as multiple hypothesis tracking and has built-in uncertainty quantification. The majority of SSAPy’s methods are vectorized and parallelizable, allowing for effective use of high-performance computer (HPC) systems. Finally, SSAPy has plotting functionality, allowing users to visualize orbits and trajectories. Examples are shown in Figure 1 and Figure 2.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1978

A model for dynamic allocation of human attention among multiple tasks

The problem of multi-task attention allocation with special reference to aircraft piloting is discussed with the experimental paradigm used to characterize this situation and the experimental results obtained in the first phase of the research. A qualitative description of an approach to mathematical modeling, and some results obtained with it are also presented to indicate what aspects of the model are most promising. Two appendices are given which (1) discuss the model in relation to graph theory and optimization and (2) specify the optimization algorithm of the model.

Sheridan, T. B.↗

NASA NTRS1980

Upper surface blowing noise of the NASA-Ames quiet short-haul research aircraft

An experimental study of the propulsive-lift noise of the NASA-Ames quiet short-haul research aircraft (QSRA) is described. Comparisons are made of measured QSRA flyover noise and model propulsive-lift noise data available in references. Developmental tests of trailing-edge treatments were conducted using sawtooth-shaped and porous USB flap trailing-edge extensions. Small scale parametric tests were conducted to determine noise reduction/design relationships. Full-scale static tests were conducted with the QSRA preparatory to the selection of edge treatment designs for flight testing. QSRA flight and published model propulsive-lift noise data have similar characteristics. Noise reductions of 2 to 3 dB were achieved over a wide range of frequency and directivity angles in static tests of the QSRA. These noise reductions are expected to be achieved or surpassed in flight tests planned by NASA in 1980.

Bohn, A. J.↗

NASA NTRS1980

Solar corona electron density distribution

The paper discusses the three and one-half months of single-frequency time delay data which were acquired from the Helios 2 spacecraft around the time of its solar occultation. The excess time delay due to integrated effect of free electrons along the signal's ray path could be separated and modeled following the determination of the spacecraft trajectory. An average solar corona and equatorial electron density profile during solar minimum were deduced from the time delay measurements acquired within 5-60 solar radii of the sun. As a point of reference at 10 solar radii from the sun, an average electron density was 4500 el/cu cm. However, an asymmetry was found in the electron density as the ray path moved from the west to east solar limb. This may be related to the fact that during entry into occultation the heliographic latitude of the ray path was about 6 deg, while during exit it was 7 deg. The Helios density model is compared with similar models deduced from different experimental techniques.

Esposito, P. B.↗

NASA NTRS1995

Spectral analyses, climatology, and interannual variability of Nimbus-7 TOMS version 6 total column ozone

This reference publication presents selected results from space-time spectral analyses of 13 years of version 6 daily global ozone fields from the Total Ozone Mapping Spectrometer (TOMS). One purpose is to illustrate more quantitatively the well-known richness of structure and variation in total ozone. A second purpose is to provide, for use by modelers and for comparison with other analysts' work, quantitative measures of zonal waves 1, 2, 3, and medium-scale waves 4-7 in total ozone. Their variations throughout the year and at a variety of latitudes are presented, from equatorial to polar regions. The 13-year averages are given, along with selected individual years which illustrate year-to-year variability. The largest long wave amplitudes occur in the polar winters and early springs of each hemisphere, and are related to strong wave amplification during major warning events. In low attitudes total ozone wave amplitudes are an order of magnitude smaller than at high latitudes. However, TOMS fields contain a number of equatorial dynamical features, including Rossby-gravity and Kelvin waves.

Stanford, J. L.↗

NASA NTRS2000

In Pursuit of the FIP Effect in Stellar Coronae

Observational data have been reduced. Sig Gem data have been fitted using the XSPEC software, though the treatment within this software of the Fe transitions arising from the n=2 levels is thought to be sufficiently inaccurate as to affect the results obtained. Data for the same star obtained by EUVE have been extracted from the archive and are being analyzed in order to try and constrain the coronal DEM. Results of the first sets of model fitting have been presented at an AAS meeting; a more substantial presentation of these and updated results in a main-stream referred journal is in progress.

Drake, Jeremy J.↗

NASA NTRS2016

A Distant Mirror: Solar Oscillations Observed on Neptune by the Kepler K2 Mission

Starting in 2014 December, Kepler (K2) observed Neptune continuously for 49 days at a 1-minute cadence. The goals consisted of studying its atmospheric dynamics, detecting its global acoustic oscillations, and those of the Sun, which we report on here. We present the first indirect detection of solar oscillations in intensity measurements. Beyond the remarkable technical performance, it indicates how Kepler would see a star like the Sun. The result from the global asteroseismic approach, which consists of measuring the oscillation frequency at maximum amplitude max velocity and the mean frequency separation between mode overtones delta velocity, is surprising as the max velocity measured from Neptune photometry is larger than the accepted value. Compared to the usual reference max velocity of the sun equal to 3100 microhertz, the asteroseismic scaling relations therefore make the solar mass and radius appear larger by 13.8 plus or minus 5.8 percent and 4.3 plus or minus 1.9 percent, respectively. The higher max velocity is caused by a combination of the value of max velocity of the sun, being larger at the time of observations than the usual reference from SOHO/VIRGO/SPM (Variability of solar IRradiance and Gravity Oscillations / on board SOHO (Solar and Heliospheric Observatory) / Sun PhotoMeters) data (3160 plus or minus 10 microhertz), and the noise level of the K2 time series, being 10 times larger than VIRGO's. The peak-bagging method provides more consistent results: despite a low signal-to-noise ratio (S/N), we model 10 overtones for degrees iota equal 0, 1, 2. We compare the K2 data with simultaneous SOHO/VIRGO/SPM photometry and Bison (Birmingham Solar-Oscillations Network) velocity measurements. The individual frequencies, widths, and amplitudes mostly match those from VIRGO and BiSON within 1 sigma, except for the few peaks with the lowest S/N.

planets and satellites: individual (Neptune) â€“ s↗

NASA NTRS2020

Calibrating a 3-Axis Accelerometer Instrument with a Less Accurate Calibration Device Part 1: Mathematical Methodology

A three-axis accelerometer instrument (3xAI) can provide the angular attitude of a 3D object using the gravity vector (g) as the sole reference. Calibrating such an instrument requires placing it at known (to some accuracy plus uncertainty) angular articulations with respect to g. This paper will show a potential process for calibrating a 3xAI by using a 2-axis rotary system (calibration device) to provide these articulations. Any calibration device (CD) with such capacity will contain internal misalignments. These misalignments, even if made relatively small or approximated to zero in the kinematics model (KM), can be detrimental to the calibration of the instrument when high measurement accuracy is required. This is especially true if the selected set of articulations chosen for calibration do not include their symmetrical counterpoints (a point where the misalignment has equal magnitude but is opposite in direction to a point chosen). The consequence of not including the combination, point and counterpoint, for any misalignment involved in the calibration, results in a biased instrument. This paper will demonstrate a calibration of the instrument using symbolic math resulting in a closed-form solution of the instrument coefficients. The main objective is to show the impact of all the CD misalignments to the instrument coefficients. This process is the basis for a more sophisticated method (shown in a future paper) for obtaining the instrument coefficients while simultaneously obtaining an estimate of the calibration device internal misalignments.

Angle↗