Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid electrolyte interphase”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Phase-field modeling of crack growth and mitigation in solid oxide cells

Fracture and crack growth is one of the main degradation mechanisms in solid oxide cells (SOCs). However, the modeling of crack growth in SOCs is challenging due to their complex microstructures and possible plasticity development within the Ni particles in Ni-based SOC electrodes. In this study, a phase-field fracture model is developed, which incorporates the SOC microstructures and phase-dependent material properties, including yield strength, fracture toughness in the bulk and at the interphase boundaries. The model is employed to study crack initiation and growth under thermal and redox cycling on the hydrogen electrode side of SOCs. The simulation results demonstrate that under thermal cycling, work-zone cracking dominates in electrolyte-supported SOCs with cracks initiated at the triple-phase boundaries, while only minor mechanical degradation occurs in hydrogen-electrode-supported SOCs after hundreds of thermal cycles. Under redox cycling, through-cracking of yttria-stabilized zirconia (YSZ) in the hydrogen electrode and electrolyte layers dominates. Finally, the simulation results suggest several crack-mitigation strategies, including decreasing the porosity in the hydrogen electrode support layer and synchronizing thermal strain to balance oxidation strain.

08 HYDROGEN↗
DOE OSTI2025

Decoding Gas Evolution Pathways and Interfacial Chemistry in Layered Oxide Cathodes for Safer Sodium‐Ion Batteries

Sodium-ion batteries (SIBs) are attractive for the low cost and abundance of sodium. Yet, gas evolution—a critical challenge in SIBs—remains underexplored. Here, online electrochemical mass spectrometry is used to probe gas evolution in layered oxide cathodes with various compositions, cutoff voltages, dopants, and particle morphologies. Compared to LiNiO 2 (LNO), NaNiO 2 releases more gas, even at lower states of charge, due to the higher covalency of Ni─O bond caused by the more ionic Na─O bond through the inductive effect. Among Co, Mn, Al, and Mg, Mn and Mg doping suppress gas release most effectively by enhancing the metal-oxygen bond strength. NaNi 1/3 Fe 1/3 Mn 1/3 O 2 (NFM) cathodes synthesized via coprecipitation (CP-NFM) and solid-state routes exhibit distinct particle morphologies; CP-NFM exhibits more gas evolution, yet secondary particle morphology helps reduce it through differential cathode-electrolyte reactivity between inner and outer primary particles. Among Li, Ti, Mg, and Cu doping in NFM, Li has the largest effect, reducing gas levels comparable to LNO. Nuclear magnetic resonance and X-ray photoelectron spectroscopies reveal that electrolyte solvent decomposition mainly produces organic-rich cathode-electrolyte interphase (CEI) rather than soluble species. NaPF 6 salt further exacerbates cathode-electrolyte reactions, forming surface Na 2 O species. The findings provide actionable guidance for designing safer, durable SIBs.

25 ENERGY STORAGE↗
DOE OSTI2018

Salt‐Based Organic–Inorganic Nanocomposites: Towards A Stable Lithium Metal/Li 10 GeP 2 S 12 Solid Electrolyte Interface

Abstract Solid‐state Li metal battery technology is attractive, owing to the high energy density, long lifespans, and better safety. A key obstacle in this technology is the unstable Li/solid‐state electrolyte (SSE) interface involving electrolyte reduction by Li. Herein we report a novel approach based on the use of a nanocomposite consisting of organic elastomeric salts (LiO‐(CH 2 O) n ‐Li) and inorganic nanoparticle salts (LiF, ‐NSO 2 ‐Li, Li 2 O), which serve as an interphase to protect Li 10 GeP 2 S 12 (LGPS), a highly conductive but reducible SSE. The nanocomposite is formed in situ on Li via the electrochemical decomposition of a liquid electrolyte, thus having excellent chemical and electrochemical stability, affinity for Li and LGPS, and limited interfacial resistance. XPS depth profiling and SEM show that the nanocomposite effectively restrained the reduction of LGPS. Stable Li electrodeposition over 3000 h and a 200 cycle life for a full cell were achieved.

Gao, Yue↗
DOE OSTI2022

Different interfacial reactivity of lithium metal chloride electrolytes with high voltage cathodes determines solid-state battery performance

A deep understanding of the interaction of the surface of cathode materials with solid electrolytes is crucial to design advanced solid-state batteries (SSBs). This is especially true for the new class of lithium metal chloride (Li-M-Cl) solid electrolytes which are receiving rapidly growing attention due to their very high oxidative stability (>4 V) in combination with good ionic conductivity that can enable long cell cycle life. While Li-M-Cl electrolytes typically contain resource-limited metals (M) such as indium or rare earths, work has focused on substituting M with more abundant elements such as zirconium. Via operando resistance measurements using intermittent current interruption we explore the dynamic evolution of the interphase at the surface of Ni-rich NCM85 or NCM111 cathode particles inside a working SSB with three different Li-(M 1 ,M 2 )-Cl catholytes (Li 3 InCl 6 , Li 2 Sc 1/3 In 1/3 Cl 4 and Li 5/2 Y 1/2 Zr 1/2 Cl 6 ) to reveal the impact of the cationic metal substitution on the interfacial chemistry. We show that the metal plays a critical role in determining high voltage stability, contrary to prior assumptions. Using a combination of cyclic voltammetry and ultraviolet photoelectron spectroscopy measurements of the electronic band structure to assess oxidative stability; coupled with DFT calculations and ToF-SIMS to evaluate products formed at the interface at different upper cutoff potentials and degrees of delithiation, we are able to differentiate between electrochemical and chemical degradation. We find that Li 2 Sc 1/3 In 1/3 Cl 4 yields the highest (and Li 3 InCl 6 the lowest) stability against electrochemical oxidation, while Li 5/2 Y 1/2 Zr 1/2 Cl 6 undergoes a detrimental chemical reaction with oxygen released from Ni-rich NCM85 at high potentials, resulting in fast capacity fading. Altogether, our work establishes a platform for the metrics and an approach that can be utilized to efficiently evaluate the stability of new halide SEs in SSB cells.

25 ENERGY STORAGE↗
DOE OSTI2024

Atomic dynamics of electrified solid–liquid interfaces in liquid-cell TEM

Electrified solid–liquid interfaces (ESLIs) play a key role in various electrochemical processes relevant to energy, biology and geochemistry. The electron and mass transport at the electrified interfaces may result in structural modifications that markedly influence the reaction pathways. For example, electrocatalyst surface restructuring during reactions can substantially affect the catalysis mechanisms and reaction products. Despite its importance, direct probing the atomic dynamics of solid–liquid interfaces under electric biasing is challenging owing to the nature of being buried in liquid electrolytes and the limited spatial resolution of current techniques for in situ imaging through liquids. Here, with our development of advanced polymer electrochemical liquid cells for transmission electron microscopy (TEM), we are able to directly monitor the atomic dynamics of ESLIs during copper (Cu)-catalysed CO 2 electroreduction reactions (CO 2 ERs). Our observation reveals a fluctuating liquid-like amorphous interphase. It undergoes reversible crystalline–amorphous structural transformations and flows along the electrified Cu surface, thus mediating the crystalline Cu surface restructuring and mass loss through the interphase layer. Furthermore, the combination of real-time observation and theoretical calculations unveils an amorphization-mediated restructuring mechanism resulting from charge-activated surface reactions with the electrolyte. Our results open many opportunities to explore the atomic dynamics and its impact in broad systems involving ESLIs by taking advantage of the in situ imaging capability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Kinetic Effects of Anion Clusters on the Interfacial Stability between Solid-State Electrolyte and Metal Anode

The success of all-solid-state batteries (ASSBs) depends on the solid-state electrolyte (SSE) exhibiting high interfacial stability and room-temperature ionic conductivity. However, the current SSEs, especially those with practical ionic conductivities (≥10 –3 S/cm) at room temperature, often develop unstable interfaces at the metal anode, in some cases with even greater severity than with liquid organic electrolytes. Despite persistent efforts, achieving interfacial stability and sufficient ionic conductivity simultaneously represents one of the greatest challenges in ASSBs. The current approaches focus on stabilizing the interface by incorporating secondary interlayers or introducing coatings by surface engineering. The method is often material-specific, and the added interlayers often deteriorate during cycling. In this work, using phase analysis and explicit interface modeling, we demonstrate a strategy to kinetically stabilize the interface between the SSE and metal anode by incorporating selected monoanion clusters in the SSE; they can effectively lower or even halt the reduction kinetics at the interface by promoting on-site formation of interphases that are highly electron insulating. The study provides insight into the kinetic effects to achieve SSEs with superior properties in bulk and at the interface.

25 ENERGY STORAGE↗
DOE OSTI2025

Promising performance of sulfide catholytes compared to halide alternatives in NMC811 cathodes for sheet-type sulfide solid-state batteries

Sulfide-based solid-state batteries (SSBs) show promise in achieving energy densities over 350 Wh/kg, yet challenges persist with their incorporation of high-voltage, nickel-rich layered oxide cathodes, such as LiNi₀.₈Mn₀.₁Co₀.₁O₂ (NMC811), due to the poor oxidation stability of sulfide solid-state electrolytes (SSEs) like Li₆PS₅Cl (LPSCl). Although halide SSEs such as Li₃InCl₆ (LIC) and Li₃YCl₆ (LYC) have previously shown promise in stabilizing high-voltage NMC cathodes, our research reveals that sulfide SSE catholytes, particularly when combined with surface-coated NMC cathodes, deliver superior performance. Here, this investigation assesses the cycling stability of various catholytes—LPSCl, LIC, Li₁₀GeP₂S₁₂ (LGPS), combined LIC-LPSCl, and LYC-LPSCl—in SSBs with LiNbO₃-coated NMC811 cathodes against sheet-type LPSCl separators. Findings indicate that while LGPS-based cathodes maintain higher capacity retention, they yield lower deliverable capacity, and LIC cathodes experience significant electrochemical degradation. Importantly, our results underscore that sulfide SSE catholytes, in conjunction with LiNbO₃-coated cathodes, optimize the cathode-electrolyte interphase (CEI), enhancing both kinetics and mass transport. These insights provide a strategic direction for optimizing catholyte composition in the development of sheet-type sulfide-based SSBs.

Catholyte↗
DOE OSTI2021

Probing the electrolyte/electrode interface with vibrational sum frequency generation spectroscopy: A review

Over the past decades, Lithium-ion batteries have seen extensive improvements, and as a result are now the primary choice in many applications for their power, energy, and durability. In recent years, battery cost has reduced by orders of magnitude through adoption of new materials and processes. Despite these advances, interfaces in these battery systems are yet to be fully understood. This is seen as a major limitation to further increase cycle life, calendar life, abuse tolerance, and performances. A major obstacle is a lack of comprehensive understanding of the complex dynamic chemical processes occurring at the electrolyte/electrode interface. In this context, vibrational sum frequency generation (vSFG) spectroscopy possesses the unique capability of probing a molecularly thin interfacial layer to obtain molecular-level information through nonlinear optical interaction. Probing the molecular level processes at the interfaces using such a versatile technique would be a game changer in the advancement of current battery research knowledge. This review article summarizes recent vSFG studies on the electrolyte/electrode interface of various electrode materials and nonaqueous electrolytes for LIBs and discusses future research perspectives. Finally, overall, this focused review highlights the advantages and versatility of vSFG that can be used to further advance present-day battery research.

25 ENERGY STORAGE↗
DOE OSTI2022

All Solid-State Li/LLZO/LCO Battery Enabled by Alumina Interfacial Coating

Li 7 La 3 Zr 2 O 12 (LLZO) garnet-type lithium-ion conductors are being investigated as a promising solid electrolyte for solid-state lithium batteries. To enable a functional all-solid-state configuration intensive investigations are needed to reduce the cathode/electrolyte interfacial resistance which contributes the most to cell performance loss. Among the commercial cathode materials investigated so far, LiCoO 2 (LCO) is one of the most stable with garnet electrolytes as only a superficial reaction has been detected between the two materials. However, even this minor reaction would block the Li-ion transport through the interface, resulting in deteriorated cell performance. In this work, we demonstrate that a thin aluminum oxide layer (5 nm) can be an effective interlayer to impede the formation of a harmful interphase and enable facile Li-ion transfer between LCO and the LLZO garnet. Room-temperature-sputtered LCO thin films were employed to form an interface with the garnet electrolyte and annealed at 800 °C to reveal the effect of the interfacial reaction on the Li-ion transfer across the interface. An aluminum oxide layer was then introduced between LCO and the garnet electrolyte by sputtering a metallic aluminum layer which is then annealed together with the upper LCO layer in oxygen, or by direct atomic layer deposition of the oxide. Compared to the LCO/LLZO/Li cells without an aluminum oxide interlayer, those with the interlayer exhibited improved performance, i.e., a stable discharge capacity of up to 90 mAh/(g LCO) at a C/10 rate, a rate capability up to 1.68C and a stable galvanostatic cycling at 0.1C for over 100 cycles with a discharge capacity fade rate of 0.15% per cycle. It was determined that aluminum diffused into the LCO layer after preventing the initial detrimental reaction between LCO and the LLZO garnet from happening during high temperature annealing, suggesting that the coating does not have to remain a physically blocking layer during cycling to function.

Electrochemistry↗
DOE OSTI2022

Investigation of the Electrode-Electrolyte Interphase in Ester-Based Electrolytes in NCM523/Graphite Cells

The use of methyl acetate (MA) and methyl propionate (MP) as co-solvents in carbonate/LiPF 6 electrolytes have been investigated in LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM523)/graphite cells to improve electrochemical performance at low temperature (−20 °C). Consistent with previous investigations, improved low temperature performance was observed with all electrolyte formulations containing esters. Detailed ex situ surface analysis of the surface films generated with the ester-based electrolytes containing electrolyte additives reveal significant changes to the SEI on graphite upon cycling at moderately elevated temperature (45 °C). In the presence of vinylene carbonate (VC) lithium plating is observed upon cycling at low temperature (−20 °C) which leads to a thicker solid electrolyte interface (SEI) upon cycling at 45 °C. Incorporation of fluoroethylene carbonate (FEC) as an electrolyte additive results in the generation of a thin SEI and alters the structure of the surface film on the NCM523 cathode resulting in stable cycling over a wide temperature range.

Rodrigo, Nuwanthi D. (ORCID:0000000343129536)↗
DOE OSTI2020

Electrolyte design for LiF-rich solid–electrolyte interfaces to enable high-performance microsized alloy anodes for batteries

Lithium batteries with Si, Al or Bi microsized (>10 µm) particle anodes promise a high capacity, ease of production, low cost and low environmental impact, yet they suffer from fast degradation and a low Coulombic efficiency. In this paper, we demonstrate that a rationally designed electrolyte (2.0 M LiPF 6 in 1:1 v/v mixture of tetrahydrofuran and 2-methyltetrahydrofuran) enables 100 cycles of full cells that contain microsized Si, Al and Bi anodes with commercial LiFePO 4 and LiNi 0.8 Co 0.15 Al 0.05 O 2 cathodes. Alloy anodes with areal capacities of more than 2.5 mAh cm -2 achieved >300 cycles with a high initial Coulombic efficiency of >90% and average Coulombic efficiency of >99.9%. These improvements are facilitated by the formation of a high-modulus LiF–organic bilayer interphase, in which LiF possesses a high interfacial energy with the alloy anode to accommodate plastic deformation of the lithiated alloy during cycling. Lastly, this work provides a simple yet practical solution to current battery technology without any binder modification or special fabrication methods.

25 ENERGY STORAGE↗
DOE OSTI2022

High Energy Aqueous Lithium-Ion Batteries (Final Report)

Lithium-ion batteries (LIBs) are a widely used energy storage device. For decades, researchers have been studying aqueous electrolytes due to their non-flammability and environmental friendless. However, the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) of water greatly limit the voltage window of the aqueous electrolyte. The recent concept of ‘solvent-in-salt’ electrolytes, namely ‘water-in-salt’ electrolytes (WISE) for aqueous batteries and ‘super-concentrated’ electrolytes for non-aqueous batteries, greatly expands the electrochemical window of these battery systems and consequently their energy density. This expansion occurs because the large number of salt aggregates in ‘solvent-in-salt’ electrolytes enables preferential salt decomposition over solvent decomposition to form robust interphase layers on electrodes, thus enhancing their stability in a wide range of operating voltages. However, even when the salt concentration reached 63m, regardless of cost, the cathodic potential of the WISE expanded only to 1.75V with an overall electrochemical stability window of <3.25V. To design the next generation of high energy aqueous LIBs, electrolytes that possess a wider electrochemical stability window and lower cost but still maintain the merit of non-flammability are much needed. In this project, we designed the aqueous LIBs with widened voltage window. We reported a cheap and non-flammable ternary eutectic electrolyte that can form a robust solid electrolyte interface (SEI)so that the cathodic limiting potential can be decreased to <1.5 V for Li 4 Ti 5 O 12 anodes, while maintaining both a high ionic conductivity of >10 -3 S cm –1 and a low viscosity. We demonstrated the super-stable2.5V LiMn 2 O 4 ||Li 4 Ti 5 O 12 pouch cell with mass loading of 2.5 mAh/cm. Further, LiCl-LiBr-Graphite/Li full cells were designed with high energy density. Finally, we use a bi-layer design to enlarge the voltage window of aqueous electrolyte, which can endow the stable cycling of aqueous Lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

A Polymer-in-Salt Electrolyte with Enhanced Oxidative Stability for Lithium Metal Polymer Batteries

Lithium (Li) metal polymer batteries (LMPBs) are a promising candidate of solid-state batteries with high safety. However, rare progress has been demonstrated so far in high voltage stability of polyethylene oxide (PEO) based polymer electrolytes for LMPBs. Herein, we revived the polymer-in-salt electrolyte (PISE) strategy based on the PEO-LiFSI system with EO/Li = 8 through a dry process to avoid the contamination of the residual solvent. The obtained PISEs exhibit quite different morphologies and coordination structures which greatly enhance the oxidative stability of polymer electrolytes. P(EO)1LiFSI has a low melting temperature, a high ionic conductivity at 60 ?C and an oxidative stability of ~4.5 V vs. Li/Li+ (overcoming the inherent low oxidative stability of PEO). With an effective interphase rich in inorganic species, in combination with good stability of the hybrid polymer electrolyte towards Li metal, the cycling stability of Li||LiNi1/3Co1/3Mn1/3O2 is greatly improved. The LMPB can retain 74.4% of capacity after 186 cycles at 60 ?C under the charge cutoff voltage of 4.3 V. The findings point out a promising strategy to develop high-voltage stable polymer electrolytes for high energy-density and safe LMPBs.

Polymer-in-salt electrolyte, lithium metal battery↗
DOE OSTI2024

Crack‐Free Single‐Crystalline LiNiO 2 for High Energy Density All‐Solid‐State Batteries

Abstract Single‐crystalline layered oxide (LiNi 1‐ x ‐ y Mn x Co y O 2 ) cathodes have been found to exhibit exceptional electrochemical properties when coupled with various inorganic solid electrolytes (ISEs) in all‐solid‐state batteries (ASSBs). Their advantages stem from the robust morphological integrity with the absence of grain boundaries and the high electrochemical oxidative stability. Here, ASSBs featuring single‐crystalline LiNiO 2 (LNO) with the highest Ni content are reported, offering a high theoretical specific capacity of 275 mAh g ‐1 alongside a high average discharge voltage (3.7 V vs Li + /Li). Through a careful investigation, it is demonstrated that micron‐sized single‐crystalline LNO (µSC‐LNO) composite cathodes with a halide ISE exhibit a high initial discharge capacity of 205 mAh g ‐1 with an outstanding cycle performance over 200 cycles in room‐temperature ASSBs. The significance of engineering parameters is emphasized, such as particle size and specific density, in promoting a homogeneous and fast Li + transport within the composite cathodes. Furthermore, the formation of undesirable interphase between the halide ISE in the cathode and sulfide ISE separator is elucidated, which may be a critical factor impeding long‐term cyclability of ASSBs. This work provides insights into the design of composite cathodes for high‐energy‐density ASSBs.

Chemistry↗
DOE OSTI2021

An ultrathin solid-state electrolyte film coated on LiNi 0.8 Co 0.1 Mn 0.1 O 2 electrode surface for enhanced performance of lithium-ion batteries

We report layered Ni-rich oxide is a promising cathode material for lithium-ion batteries (LIBs) of high energy density, yet its poor electrochemical stability induced by electrode-electrolyte interfacial degradation has still needed to be addressed. Surface coating is one of the powerful techniques to tackle this issue, nevertheless, it has been extensively used on particle but not electrode regarding a larger area of protection. Herein, we have covered a nano-scaled layer of lithium phosphorus oxynitride (LiPON) on the electrode level of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM) surface and found lower impedance, longer cycle life, and better safety for treated battery. Most notably, such an NCM-LiPON based 1.3 Ah pouch cell delivers an energy density of 364.4 Wh kg -1 (based on positive and negative materials), along with the retention of 80.0% over 745 cycles at 0.5 C-rate, which is 1.3 times longer than the bare one. This results from modification of both superficial cathode-electrolyte interphase (CEI) and structure stabilization of general particle surface, therefore, role of conformal coating upon electrode surface should be highlighted.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Investigating the effect of heterogeneities across the electrode|multiphase polymer electrolyte interfaces in high-potential lithium batteries

Polymer electrolytes hold great promise for safe and high-energy batteries comprising solid or semi-solid electrolytes. Multiphase polymer electrolytes, consisting of mobile and rigid phases, exhibit fast ion conduction and desired mechanical properties. However, fundamental challenges exist in understanding and regulating interactions at the electrode|electrolyte interface, especially when using high-potential layered oxide active materials at the positive electrode. Here we demonstrate that depletion of the mobile conductive phase at the interface contributes to battery performance degradation. Molecular ionic composite electrolytes, composed of a rigid-rod ionic polymer with nanometric mobile cations and anions, serve as a multiphase platform to investigate the evolution of ion conductive domains at the interface. Chemical and structural characterizations enable the visualization of concentration heterogeneity and spatially resolve the interfacial chemical states over a statistically significant field of view for buried interfaces. We report that concentration and chemical heterogeneities prevail at electrode|electrolyte interfaces, leading to phase separation in polymer electrolytes. In conclusion, understanding the hidden roles of interfacial chemomechanics in polymer electrolytes enables us to design an interphase tailoring strategy based on electrolyte additives to mitigate the interfacial heterogeneity and improve battery performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Lithium halide cathodes for Li metal batteries

Lithium halides cathodes potentially offer a high energy density at a low cost for rechargeable batteries. However, these cathodes suffer from quick capacity decay in organic electrolytes and the failiure mechanism remains elusive. Here, we report that liquefying the halogen or interhalogen compounds is a prerequisite for achieving high reversibility for the lithium halides cathodes. The gas or solid halogen can be liquefied by using interhalogen compounds with different electronegativity or changing the temperature. As a proof of concept, reversible LiCl conversion-intercalation chemistry in organic electrolyte is demonstrated by using either redox coupling with less electronegative I/Br to form liquid ICl/BrCl or reducing the temperature to -30oC. Further, the LiCl-LiBr-graphite cathodes in 1.6M lithium difluoro(oxalato)borate/1.6M lithium triflate in diglyme electrolytes achieve a high reversible specific capacity of 250 mAh/g at 3.7 V with an energy density being comparable to or higher than transition metal oxide cathodes at a much lower cost.

25 ENERGY STORAGE↗
DOE OSTI2021

In Situ Formation of Polycyclic Aromatic Hydrocarbons as an Artificial Hybrid Layer for Lithium Metal Anodes

Nonuniform Li deposition causes dendrites and low Coulombic efficiency (CE), seriously hindering the practical applications of Li metal. Herein, we developed an artificial solid-state interphase (SEI) with planar polycyclic aromatic hydrocarbons (PAHs) on the surface of Li metal anodes by a facile in situ formation technology. The resultant dihydroxyviolanthron (DHV) layers serve as the protective layer to stabilize the SEI. In addition, the oxygen-containing functional groups in the soft and conformal SEI film can regulate the diffusion and transport of Li ions to homogenize the deposition of Li metal. The artificial SEI significantly improves the CEs and shows superior cyclability of over 1000 h at 4 mAh cm –2 . The LiFePO 4 /Li cell (2.8 mAh cm –2 ) enables a long cyclability for 300 cycles and high CEs of 99.8%. Furthermore, this work offers a new strategy to inhibit Li dendrite growth and enlightens the design on stable SEI for metal anodes.

25 ENERGY STORAGE↗