Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structured Programming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Flight measurements of surface pressures on a flexible supercritical research wing

A flexible supercritical research wing, designated as ARW-1, was flight-tested as part of the NASA Drones for Aerodynamic and Structural Testing Program. Aerodynamic loads, in the form of wing surface pressure measurements, were obtained during flights at altitudes of 15,000, 20,000, and 25,000 feet at Mach numbers from 0.70 to 0.91. Surface pressure coefficients determined from pressure measurements at 80 orifice locations are presented individually as nearly continuous functions of angle of attack for constant values of Mach number. The surface pressure coefficients are also presented individually as a function of Mach number for an angle of attack of 2.0 deg. The nearly continuous values of the pressure coefficient clearly show details of the pressure gradient, which occurred in a rather narrow Mach number range. The effects of changes in angle of attack, Mach number, and dynamic pressure are also shown by chordwise pressure distributions for the range of test conditions experienced. Reynolds numbers for the tests ranged from 5.7 to 8.4 x 1,000,000.

Eckstrom, C. V.↗

Vibration and structureborne noise in space station

Analytical models and computer programs for structural response calculations under action of mechanical point loads were developed for single wall shells (composite or aluminum), double wall shells (composite or aluminum), and single wall or double wall circular plates (aluminum). The design configuration of the habitability modules of the space station concept are expected to be discretely stiffened cylindrical shells with truncated cone type end caps or flat but stiffened circular end plates. Analytical formulations and response calculations were performed for the case where the stiffened shell is represented by an orthotropic shell model. The natural frequencies can be calculated. For application to low frequency (below 1000Hz) vibrations and noise generation, such a model might be adequate to evaluate vibration and noise transmission characteristics of space station habitability modules. Parametric studies are now being performed to assess interior noise environment inside a habitability module to mechanically induced vibrations.

Vaicaitis, R.↗

A computer analysis program for interfacing thermal and structural codes

A software package has been developed to transfer three-dimensional transient thermal information accurately, efficiently, and automatically from a heat transfer analysis code to a structural analysis code. The code is called three-dimensional TRansfer ANalysis Code to Interface Thermal and Structural codes, or 3D TRANCITS. TRANCITS has the capability to couple finite difference and finite element heat transfer analysis codes to linear and nonlinear finite element structural analysis codes. TRANCITS currently supports the output of SINDA and MARC heat transfer codes directly. It will also format the thermal data output directly so that it is compatible with the input requirements of the NASTRAN and MARC structural analysis codes. Other thermal and structural codes can be interfaced using the transfer module with the neutral heat transfer input file and the neutral temperature output file. The transfer module can handle different elemental mesh densities for the heat transfer analysis and the structural analysis.

Thompson, R. L.↗

Constitutive modeling for isotropic materials

A state-of-the-art review of applicable constitutive models with selection of two for detailed comparison with a wide range of experimental tests was conducted. The experimental matrix contained uniaxial and biaxial tensile, creep, stress relaxation, and cyclic fatigue tests at temperatures to 1093 C and strain rates from .0000001 to .001/sec. Some nonisothermal cycles will also be run. The constitutive models will be incorporated into the MARC finite element structural analysis program with a demonstration computation made for advanced turbine blade configuration. In the code development work, particular emphasis is being placed on developing efficient integration algorithms for the highly nonlinear and stiff constitutive equations. Another area of emphasis is the appropriate and efficient methodology for determing constitutive constants from a minimum extent of experimental data.

Lindholm, U. S.↗

Parallel processors and nonlinear structural dynamics algorithms and software

A nonlinear structural dynamics program with an element library that exploits parallel processing is under development. The aim is to exploit scheduling-allocation so that parallel processing and vectorization can effectively be treated in a general purpose program. As a byproduct an automatic scheme for assigning time steps was devised. A rudimentary form of the program is complete and has been tested; it shows substantial advantage can be taken of parallelism. In addition, a stability proof for the subcycling algorithm has been developed.

Belytschko, T.↗

COFS 1 research overview

The Control of Flexible Structures (COFS) program is divided into three areas of research. These three areas are controls/structures analysis development, ground test experiments, and in-space experiments. The ground test experiments are intended to validate analyses and to confirm through hardware tests our technical readiness to successfully fly the Mast hardware. There is this close relation to the results of ground tests and analytical predictions that must be understood before flight experiments may be attempted. Details relative to each program area are given.

Horner, G. C.↗

Analysis and simulation of the MAST (COFS-1 flight hardware)

In-house analysis work in support of the Control of Flexible Structures (COFS) program is being performed at the NASA Langley Research Center. The work involves evaluation of the proposed design configuration, controller design as well as actuator dynamic modeling, and MAST/actuator dynamic simulation of excitation and damping. A complete finite element model of the MAST has been developed. This finite element model has been incorporated into an optimization procedure which minimizes total mass while maintaining modal coupling. Results show an increase in the total mass due to additional constraints (namely, the diagonal frequency constraint) imposed on the baseline design. A valid actuator dynamic model is presented and a complete test sequence of the proposed flight experiment is demonstrated. The actuator dynamic model is successfully used for damping and the stroke limitations for first mode excitation are demonstrated. Plans are to incorporate additional design variables and constraints into the optimization procedure (such as actuator location) and explore alternative formulations of the objective function. A different actuator dynamic model to include hardware limitations will be investigated.

Horta, Lucas G.↗

Experimental and theoretical studies of time-averaged and time resolved rotor heat transfer

Efforts in support of the Space Shuttle Main Engine (SSME) structural durability program have concentrated on obtaining detailed time-averaged and time-resolved (or phase-locked) measurements on a full-scale rotating turbine both with and without cold gas injection and on theoretical studies designed to improve the prediction capability for these turbine flows. The experimental efforts have concentrated on use of the Garrett TFE 731-2 hp turbine. However, it has been possible to apply the theoretical efforts to predicting heat-flux distributions obtained for two additional turbines - i.e., (1) the Garrett low aspect ratio turbine (LART) and (2) the Teledyne 702 turbine. The experimental technique is the short duration, shock-tunnel approach, in which fast-response, thin-film resistance thermometers are used to measure surface temperature histories at prescribed locations on the turbine component parts. Heat-flux values are then inferred from the temperature histories by using standard data reduction procedures. The turbine being used is the Garrett TFE 731-2 hp stage, and both the nozzle guide vanes and the rotor blades are heavily instrumented with thin-film heat-flux gauges. Depending on how the data from a particular heat-flux gauge are recorded, one can get either time-resolved (or phase-locked) or time-averaged results. Both types of data are illustrated.

Dunn, M. G.↗

Command/response protocols and concurrent software

A version of the program to control the parallel jaw gripper is documented. The parallel jaw end-effector hardware and the Intel 8031 processor that is used to control the end-effector are briefly described. A general overview of the controller program is given and a complete description of the program's structure and design are contained. There are three appendices: a memory map of the on-chip RAM, a cross-reference listing of the self-scheduling routines, and a summary of the top-level and monitor commands.

Bynum, W. L.↗

Deformations in VLBI antennas

A study is presented of deformations in antennas with the emphasis on their influence on VLBI measurements. The GIFTS structural analysis program has been used to model the VLBI antenna in Fairbanks (Alaska). The report identifies key deformations and studies the effect of gravity, wind, and temperature. Estimates of expected deformations are given.

Clark, T. A.↗

Structural Ceramics

This publication is a compilation of abstracts and slides of papers presented at the NASA Lewis Structural Ceramics Workshop. Collectively, these papers depict the scope of NASA Lewis' structural ceramics program. The technical areas include monolithic SiC and Si3N4 development, ceramic matrix composites, tribology, design methodology, nondestructive evaluation (NDE), fracture mechanics, and corrosion.

Source record↗

Dynamic resource allocation in a hierarchical multiprocessor system: A preliminary study

An integrated system approach to dynamic resource allocation is proposed. Some of the problems in dynamic resource allocation and the relationship of these problems to system structures are examined. A general dynamic resource allocation scheme is presented. A hierarchial system architecture which dynamically maps between processor structure and programs at multiple levels of instantiations is described. Simulation experiments were conducted to study dynamic resource allocation on the proposed system. Preliminary evaluation based on simple dynamic resource allocation algorithms indicates that with the proposed system approach, the complexity of dynamic resource management could be significantly reduced while achieving reasonable effective dynamic resource allocation.

Ngai, Tin-Fook↗

Structures and materials technology for Space Station

This paper provides a brief overview of the NASA Langley structures and materials technology program for large space structures. Concepts developed for constructing large space truss structures such as space platforms and antennas are considered. The applications of the finding to the Space Station initiative are addressed.

Blankenship, Charles P.↗

Aeroelastic tailoring for oblique wing lateral trim

Composite material aeroelastic tailoring is presently explored as a means for the correction of the roll trim imbalance of oblique-wing aircraft configurations. The concept is demonstrated through the analysis of a realistic oblique wing by a static aeroelastic computational procedure encompassing the full potential transonic aerodynamic code FLO22 and a Ritz structural plate program that models the stiffness due to symmetrical-but-unbalanced composite wing skins. Results indicate that asymetric composite tailoring reduces the aileron deflection needed for roll equilibrium, and reduces control surface hinge moment and drag. Wing skin stresses are, however, very high.

Bohlmann, Jonathan D.↗

Concurrent and vectorized mixed time, explicit nonlinear structural dynamics algorithms

A nonlinear structural dynamics program with an element library that exploits parallel processing is described. The aim is to exploit scheduling-allocation so that parallel processing and vectorization can effectively be treated in a general purpose program with explicit time integration and different time steps in different parts of the mesh. The program uses an element group scheme, which, as a by-product, also provides an automatic scheme for assigning different time steps to different parts of the mesh. The program has been tested on the Alliant FX/8; it shows a fivefold improvement in speed over compiler optimization.

Belytschko, Ted↗

Calculation of low frequency vibrational resonances of submerged structures

Numerical techniques for calculating the low frequency vibrational resonances of submerged structures are reviewed. Both finite element and boundary element approaches for calculating fully-coupled added mass matrices for use in NASTRAN analysis are described and illustrated. The finite element approach is implemented using existing capability in NASTRAN. The boundary element approach uses the NASHUA structural-acoustics program to compute the added mass matrix. The two procedures are compared to each other for the case of a submerged cylindrical shell with flat end closures. It is concluded that both procedures are capable of computing accurate submerged resonances and that the more elegant boundary element procedure is easier to use but may be more expensive computationally.

Everstine, Gordon C.↗

Error analysis for semi-analytic displacement derivatives with respect to shape and sizing variables

Sensitivity analysis is fundamental to the solution of structural optimization problems. Consequently, much research has focused on the efficient computation of static displacement derivatives. As originally developed, these methods relied on analytical representations for the derivatives of the structural stiffness matrix (K) with respect to the design variables (b sub i). To extend these methods for use with complex finite element formulations and facilitate their implementation into structural optimization programs using the general finite element method analysis codes, the semi-analytic method was developed. In this method the matrix the derivative of K/the derivative b sub i is approximated by finite difference. Although it is well known that the accuracy of the semi-analytic method is dependent on the finite difference parameter, recent work has suggested that more fundamental inaccuracies exist in the method when used for shape optimization. Another study has argued qualitatively that these errors are related to nonuniform errors in the stiffness matrix derivatives. The accuracy of the semi-analytic method is investigated. A general framework was developed for the error analysis and then it is shown analytically that the errors in the method are entirely accounted for by errors in delta K/delta b sub i. Furthermore, it is demonstrated that acceptable accuracy in the derivatives can be obtained through careful selection of the finite difference parameter.

Fenyes, Peter A.↗

Optimizing for minimum weight when two different finite element models and analyses are required

The Finite Element Structural Optimization Program's (FESOP) ability to perform minimum weight optimization using two different finite element analyses and models is discussed. FESOP uses the ADS optimizer developed by Dr. Garret Vanderplaats to solve the nonlinear constrained optimization problem. The design optimization problem requires a response spectrum analysis and model to evaluate the stress and displacement constraints. However, the problem needs a frequency analysis and model to calculate the natural frequencies used to evaluate the frequency range constraints. The results of both the successful and unsuccessful approaches used to solve this difficult weight minimization problem are summarized. The results show that no one ADS optimization algorithm worked in all cases. However, the Sequential Convex Programming and Modified Method of Feasible Directions algorithms were the most successful.

Hall, Jeffrey C.↗