Search NASA⌕ Search

SEARCH · Search NASA

Results for “amorphous”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Correlating conductivity and Seebeck coefficient to doping within crystalline and amorphous domains in poly(3-(methoxyethoxyethoxy)thiophene)

Molecular doping of conjugated polymers (CPs) plays a vital role in optimizing organic electronic and energy applications. For the case of organic thermoelectrics, it is commonly believed that doping CPs with a strong dopant could result in higher conductivity (σ) and thus better power factor (PF). Herein, by investigating thermoelectric performance of a polar side-chain bearing CP, poly(3- (methoxyethoxyethoxy)thiophene) (P3MEET), vapor doped with fluorinatedderivative of tetracyanoquinodimethane FnTCNQ (n = 1, 2, 4), we show that using strong dopants can in fact have detrimental effects on the thermoelectric performance of CPs. Despite possessing higher electron affinity, doping P3MEET with F4TCNQ only results in a σ (27.0 S/cm) comparable to samples doped with other two weaker dopants F2TCNQ and F1TCNQ (26.4 and 20.1 S/cm). Interestingly, F4TCNQ-doped samples display a marked reduction in the Seebeck coefficient (α) compared to F1TCNQ- and F2TCNQ-doped samples from 42 to 13 μV/ K, leading to an undesirable suppression of the PF. Additionally, structural characterizations coupled with Kang-Snyder modeling of the α–σ relation show that the reduction of α in F4TCNQ-doped P3MEET samples originates from the generation of low mobility carrier within P3MEET's amorphous domain. Our results demonstrate that factors such as dopant distribution and doping efficiency within the crystalline and amorphous domains of CPs should play a crucial role in advancing rational design for organic thermoelectrics.

36 MATERIALS SCIENCE↗

Amorphous alumina thin films deposited on titanium: Interfacial chemistry and thermal oxidation barrier properties

Ti/Al 2 O 3 bilayer stacks are used as model systems to investigate the role of atomic layer deposition (ALD) and chemical vapor deposition (CVD) to prepare 30-180 nm thick amorphous alumina films as protective barriers for the medium temperature oxidation (500-600⁰C) of titanium, which is employed in aeronautic applications. X-ray diffraction (XRD), transmission electron microscopy (TEM) with selected area electron diffraction (SAED), and X-ray photoelectron spectroscopy (XPS) results show that the films produced from the direct liquid injection (DLI) CVD of aluminum tri-isopropoxide (ATI) are poor oxygen barriers. The films processed using the ALD of trimethylaluminum (TMA) show good barrier properties but an extensive intermixing with Ti which subsequently oxidizes. In contrast, the films prepared from dimethyl aluminum isopropoxide (DMAI) by CVD are excellent oxygen barriers and show little intermixing with Ti. Overall, these measurements correlate the effect of the alumina coating thickness, morphology, and stoichiometry resulting from the preparation method to the oxidation barrier properties, and show that compact and stoichiometric amorphous alumina films offer superior barrier properties.

36 MATERIALS SCIENCE↗

Au and Pt Diffusion in Electrodeposited Amorphous Sb 2 Te 3 Thin Films

Amorphous Sb 2 Te 3 thin films are synthesized using electrodeposition in different thicknesses to explore their solid electrolytic nature with respect to some noble metals. Au and Pt are used as the substrate materials and thermally diffused into the Sb 2 Te 3 films under passivated and nonpassivated conditions. Rutherford backscattering spectrometry is used to study the Au and Pt diffusion into the films as a function of depth. It is found that Au diffuses into the Sb 2 Te 3 thin films even at room temperature. In contrast, there is no observable diffusion of Pt at room temperature. At a higher temperature (i.e., 200 °C), both Au and Pt diffuse into the Sb 2 Te 3 thin films and Au diffusion is more significant than Pt. Overall, the findings suggest that amorphous Sb 2 Te 3 can be used as a good solid electrolyte to permit the diffusion of some noble metals such as Au and Pt.

36 MATERIALS SCIENCE↗

Effect of Ion Irradiation on Amorphous and Crystalline Ge–Se and Their Application as Phase Change Temperature Sensor

Research on phase change materials is predominantly focused on their application as memory devices or for temperature control which requires low phase change temperature. The Ge–Se binary chalcogenide glass system with its wide glass-forming region is a potential candidate for high-temperature and high-radiation phase change applications. In this study, the concept of employing Ge x Se 100– x glasses to monitor high temperature (450–528 °C) using the phase change effect, is reported. Materials selection, device structure, and performance of prototype sensors are analyzed. In addition, the effect of heavy ion irradiation by Xe ions with energies of 200, 600, and 1000 keV (fluence ≈10 14 cm –2 ) on the Ge x Se 100– x ( x = 30, 33, 40) thin films and phase change devices is studied. The irradiation effect on the amorphous and crystalline structure of the thin films is evaluated by Raman spectroscopy and X-ray diffraction (XRD). Although the changes in the structural units of amorphous films are negligible, in crystalline films orthorhombic-GeSe 2 crystals are found to be most affected by irradiation and a new phase, orthorhombic GeSe is found in the thin films after irradiation. The performance of a sensor with an active film of Ge 40 Se 60 is also shown as an example.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Non-Equilibrium Synthesis of Highly Active Nanostructured, Oxygen-Incorporated Amorphous Molybdenum Sulfide HER Electrocatalyst

Molybdenum sulfide emerged as promising hydrogen evolution reaction (HER) electrocatalyst thanks to its high intrinsic activity, however its limited active sites exposure and low conductivity hamper its performance. To address these drawbacks, the non-equilibrium nature of pulsed laser deposition (PLD) is exploited to synthesize self-supported hierarchical nanoarchitectures by gas phase nucleation and sequential attachment of defective molybdenum sulfide clusters. Furthermore, the physics of the process are studied by in situ diagnostics and correlated to the properties of the resulting electrocatalyst. The as-synthesized architectures have a disordered nanocrystalline structure, with nanodomains of bent, defective S-Mo-S layers embedded in an amorphous matrix, with excess sulfur and segregated molybdenum particles. Oxygen incorporation in this structure fosters the creation of amorphous oxide/oxysulfide nanophases with high electrical conductivity, enabling fast electron transfer to the active sites. The combined effect of the nanocrystalline pristine structure and the surface oxidation enhances the performance leading to small overpotentials, very fast kinetics (35.1 mV dec -1 Tafel slope) and remarkable long-term stability for continuous operation up to -1 A cm -2 . This work shows possible new avenues in catalytic design arising from a non-equilibrium technique as PLD and the importance of structural and chemical control to improve the HER performance of MoS-based catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reconfiguration of Amorphous Complex Oxides: A Route to a Broad Range of Assembly Phenomena, Hybrid Materials, and Novel Functionalities

This work demonstrate that reconfiguration of amorphous oxide layers drives the assembly of oxide-based and freestanding nanomembranes into 3D structures with a radius of a few hundred nanometers. Reconfiguration-driven assembly is a versatile approach to impart large strains and strain gradients in a broad palette of complex oxides. This capability allows for manipulating and enhancing ferroelectricity, flexoelectricity, piezoelectricity, superconductivity, and ferromagnetism in complex oxides. Moreover, by the approach presented in this work, strain-engineered oxides are obtained in the form of 3D structures that can be fabricated in parallel on any substrate, including large-area and single crystalline semiconductor substrates. This approach will create a vast expanse of possibilities to investigate and leverage strain-tunable effects in amorphous, poly-crystalline, and single-crystalline complex oxides. Reconfiguration-driven assembly of NMs also allows combining different materials in a radial geometry and through scalable processes. For example, radial superlattices of Si (or GaAs) and various complex oxides or alternating layers of different complex oxides (e.g., SrTiO 3 and LaAlO 3 ) could be fabricated by release and heating of bilayer NMs. Here, a broad palette of electronic band structures and spin–orbit interactions could then be obtained by tailoring the curvature of the self-assembled NMs and the materials that the heterostructure comprises.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Amorphous K–Co–Mo–S x Chalcogel: A Synergy of Surface Sorption and Ion-Exchange

Chalcogel represents a unique class of meso- to macroporous nanomaterials that offer applications in energy and environmental pursuits. We report the synthesis of an ion-exchangeable amorphous chalcogel using a nominal composition of K 2 CoMo 2 S 10 (KCMS) at room temperature is reported. Synchrotron X-ray pair distribution function (PDF), X-ray absorption near-edge structure (XANES), and extended X-ray absorption fine structure (EXAFS) reveal a plausible local structure of KCMS gel consisting of Mo 5+ 2 and Mo 4+ 3 clusters in the vicinity of di/polysulfides which are covalently linked by Co 2+ ions. The ionically bound K + ions remain in the percolating pores of the Co–Mo–S covalent network. XANES of Co K-edge shows multiple electronic transitions, including quadrupole (1s→3d), shakedown (1s→4p + MLCT), and dipole allowed 1s→4p transitions. Remarkably, despite a lack of regular channels as in some crystalline solids, the amorphous KCMS gel shows ion-exchange properties with UO 2 2+ ions. Additionally, it also presents surface sorption via [S∙∙∙∙UO 2 2+ ] covalent interactions. Overall, this study underscores the synthesis of quaternary chalcogels incorporating alkali metals and their potential to advance separation science for cations and oxo-cationic species by integrating a synergy of surface sorption and ion-exchange.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Impact of deposition conditions on the crystallization kinetics of amorphous GeTe films

The speed at which phase change memory devices can operate depends strongly on the crystallization kinetics of the amorphous phase. To better understand factors that affect the crystallization rate, we have investigated in this paper crystallization of GeTe films as a function of their deposition temperatures and deposition rates, using X-ray synchrotron radiation and Raman spectroscopy. As-deposited films were found to be fully amorphous under all conditions, even though films deposited at higher temperatures and lower rates experienced lower effective quench rates. Non-isothermal transformation curves show that the apparent crystallization temperature of GeTe films decreases with increasing deposition temperature and decreasing deposition rate. It was found that this correlates with a decrease in the activation energy for nucleation (calculated using Kissinger’s analysis), while the activation energy for crystal growth remained unaffected. Finally, from Raman spectroscopy measurements, it was found that increasing the deposition temperature or decreasing the deposition rate, and therefore the effective quench rate, reduces the number of homopolar Te–Te bonds and thereby reduces the barrier to crystal nucleation.

36 MATERIALS SCIENCE↗

Amorphization kinetics in strontium titanate at 16 and 300 K under argon ion irradiation

Here, the accumulation of irradiation-induced disorder in SrTiO 3 single crystals irradiated at 16 K with 200 keV Ar ions has been investigated using Rutherford backscattering spectrometry along the < 100 > channeling direction and compared with previous results obtained at 300 K under identical irradiation conditions. As expected, amorphization at 16 K occurs at a much lower fluence than at 300 K due to dynamic recovery of irradiation-induced defects at 300 K. Utilizing a comprehensive damage accumulation model for analysis of the data, irradiation at 16 K results only in the formation of point defects and amorphous pockets, while defect clusters are also formed at 300 K. High defect mobility under irradiation at 300 K tends to promote recombination and clustering of point defects. These results suggest that defect diffusion processes in SrTiO 3 are not thermally active at 16 K.

36 MATERIALS SCIENCE↗

High-Performance Bulk MgB{sub 2} Superconductor Using Amorphous Nano-boron

MgB{sub 2} bulks were produced by in situ solid-state reaction in Ar gas using high-purity commercial powders of Mg metal and amorphous nano-B mixed in a fixed ratio of Mg:B = 1:2. Single-phase materials have been obtained and grain structure and its implications are reported. All samples were sintered at 775 °C for 3 h in Ar atmosphere. X-ray diffraction results show that high-purity MgB{sub 2} phase has been fabricated, which as well is reflected in critical temperature (T{sub c} = 37.8 K). Magnetic measurements reveal a high critical current density (J{sub c}) value such as 408 kA/cm{sup 2} when nano-amorphous boron is used. SEM studies show that nano-ordered MgB{sub 2} grains are formed, thereby creating large number of grain boundaries responsible for high critical current densities. Analysis of normalized pinning force curve as a function of reduced magnetic field indicates that dominant pinning is caused by grain boundaries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On T-Amorphous Association Schemes

An association scheme is said to be T-amorphous if it is antisymmetric and any tournament obtained by an appropriate merging of its classes is doubly regular. The goal of this paper is to study basic properties of T-amorphous schemes.

97 MATHEMATICS AND COMPUTING↗

Semi-empirical estimation of the attenuation loss for amorphous ZBLAN glass

ZBLAN glass tends to undergo heavy devitrification, forming crystallites that act as scattering centers and results in a large attenuation loss. In this study, attenuation loss values were obtained for ZBLAN glass test samples that were melted and then cooled rapidly at a rate of 4000 °C/min, which yielded amorphous samples that were free of micro/nano-crystalline inclusions. Using an approach by Forouhi and Bloomer, which incorporates Kramers–Kronig relations, in conjunction with measured optical data using ellipsometry, an attenuation loss of 0.092 dB/Km at 1800 nm wavelength was estimated for amorphous ZBLAN test samples.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Plastic Deformation in an Amorphous Ni-P Coating

An experimental and numerical investigation of the hardness and associated plastic deformation in as-deposited and as-annealed nickel-phosphorus (Ni-P) coatings was conducted. In addition to the indentation-deformation behavior, the deformation morphology underneath the indenter was examined. The yield strength extracted from the indentation data is as high as 5.6 GPa, indicating pressure-sensitive plasticity. Results show that the as-deposited Ni-P coating was deformed appreciably through the shear-band mechanism with semi-circular and radial shear-band morphologies. From the incremental loading-unloading cyclic experiments, the phenomena on hardening and recovery, which have scarcely been recognized in amorphous materials at room temperature, were observed in the amorphous coating using instrumented nanoindentation. A numerical simulation of the interfacial indentation test between the Ni-P coating and the substrate reveals the pile-up and shear bands of the Ni-P coating that were observed during the indentation tests.

Shen, Yongfeng↗

Electrochemical Behavior of HVOF-Sprayed Amorphous and Nanocrystalline Fe-Based Fe{sub 73.13}Si{sub 11.12}B{sub 10.79}Cr{sub 2.24}C{sub 2.72} Composite Coatings

The present work describes a series of new amorphous and nanocrystalline composite coatings (composition: 87.6% Fe, 6.7% Si, 2.5% B, 2.5% Cr, 0.7% C in wt.%) on a mild steel substrate made by high-velocity oxy-fuel thermal spray at different feed rates of 20, 30 and 40 g/min. The microstructure characterization using scanning electron microscopy coupled with energy-dispersive spectroscopy shows uniform and adherent coatings of different thickness depending on the feed rate. The structure of the coating is composite in nature (mixture of amorphous and nanocrystalline phases) as confirmed by the x-ray diffraction and transmission electron microscopy. The hardness of the coating is almost 6-7 times than that of the substrate. Though polarization test of the coating demonstrates corrosion resistance in 3.5% NaCl solution similar to the substrate, the difference of corrosion potentials of the coatings and the substrate is largely negative (~ more than 200 mV against saturated calomel electrode) suggesting anodic nature of the coating as compared to the substrate resulting in sacrificial effect.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructure and Mechanical Properties of Powder Thixoforged Amorphous Ni{sub 55}Nb{sub 35}Si{sub 10}-Reinforced Al Matrix Composites

Powder thixoforging was used to produce amorphous Ni{sub 55}Nb{sub 35}Si{sub 10}-reinforced Al matrix composites from recycled Al powders obtained from ball-milled Al520 end-milled billets. The amorphous reinforcing material was uniformly dispersed in the Al matrix and bonded adequately with it without undesired interfacial reactions. The compressive yield strength of composites with 45% reinforcement content increased 248% to 794 MPa over as-cast samples. The maximum elongation and hardness of samples were 15%, and 60.4 HRA, respectively. The relative density of the unreinforced thixoforged sample was 99.8%, indicating near-perfect compaction of Al powders. The maximum elongation, hardness, and compressive yield strength of thixoforged monolithic matrix alloys were, respectively, 40%, 56.9 HRA, and 747 MPa (a 228% increase in CYS over the cast alloy). In contrast, cold-forged samples showed only 82% increase in compressive yield strength over the as-cast alloy. Powder thixoforging introduced in this study—even without reinforcement—delivers better mechanical properties compared to cold forging most likely due to the refinement and modification of the microstructure during powder ball milling.

36 MATERIALS SCIENCE↗

The Effects of Strain-Annealing on Tuning Permeability and Lowering Losses in Fe-Ni-Based Metal Amorphous Nanocomposites

Here, Fe-Ni-based metal amorphous nanocomposites with a range of compositions (Fe 100–x Ni x ) 80 Nb 4 Si 2 B 14 (30 ≤ x ≤ 70) are investigated for motor and transformer applications, where it is beneficial to have tunable permeability. It is shown that strain annealing offers an effective method for tuning permeability in these alloys. For an Fe-rich alloy, permeability increased from 4000 to 16,000 with a positive magnetostriction. In a Ni-rich alloy, permeability decreased from 290 to 40 with a negative magnetostriction. Significant elongations (above 60%) are observed during strain annealing at high stress. Crystallization products have been determined in all alloys heated to 480°C. γ-FeNi is formed in all alloys, while (Fe 30 Ni 70 ) 80 Nb 4 Si 2 B 14 also undergoes secondary crystallization at temperatures of approximately 480°C to form a phase with the Cr 23 C 6 -type structure and a likely composition of Fe 21 Nb 2 B 6 . Toroidal losses have been measured for (Fe 70 Ni 30 ) 80 Nb 4 Si y B 16–y (0 ≤ y ≤ 3) at various annealing temperatures. At an induction of 1 T and frequency of 400 Hz and 1 kHz, the toroidal losses obtained are W 1.0T, 400 Hz = 0.9 W/kg and W 1.0T, 1 kHz = 2.3 W/kg, respectively. These losses are lower than losses recently reported for state of the art 3.0% and 6.5% silicon steels, a Metglas Fe-based amorphous alloy, and some Fe-based nanocomposites.

36 MATERIALS SCIENCE↗

In situ dynamic TEM characterization of unsteady crystallization during laser processing of amorphous germanium

The unsteady propagation mechanism for the crystallization of amorphous germanium (a-Ge) was studied with in situ movie-mode dynamic transmission electron microscopy (MM-DTEM). We used short laser pulses to heat sputter-deposited a-Ge films and the resulting crystallization process was imaged with up to 16 sequential 50 ns long electron pulses separated by a controlled delay that was varied between 0.5 and 5 μs. The unsteady crystallization in the radial, net-growth direction was observed to occur at a decreasing rate of ~1.5–0.2 m/s through a mechanism involving the formation of discrete ~1.1 μm wide bands that grew with velocities of 9–12 m/s perpendicular to the radial direction and along the perimeter of the crystallized area. The crystallization rate and resulting microstructure were consistent with a liquid-mediated growth mechanism, which suggests that locally the band front reaches the amorphous melting temperature of Ge. Furthermore, a mechanism based on the notion of a critical temperature is proposed to explain the unsteady, banded behavior.

36 MATERIALS SCIENCE↗

Growth of epitaxial CdTe thin films on amorphous substrates using single crystal graphene buffer

Traditionally, a high-quality CdTe film can only be grown on a single crystal substrate with a small lattice mismatch. We report the epitaxy of CdTe films on monolayer single crystal graphene buffered amorphous SiO 2 /Si(100) substrates, despite a 86% lattice mismatch between CdTe(111) and graphene. X-ray pole figure, electron backscatter diffraction mapping and transmission electron microscopy all confirm that the epitaxial CdTe films are composed of two domains: the primary and the Σ3 twin. The crystal quality of films is shown to improve as the post-deposition annealing temperature increases. However, the rotational misalignment in CdTe remains large even after annealing. Through density functional theory calculations on the charge transfer distribution at the interface of CdTe and graphene, it is found that the interface is dominated by the weak van der Waals interaction, which explains the large spread of in-plane orientation in CdTe films. Furthermore, the rotational misalignment in graphene itself is also confirmed to produce the large in-plane orientation spread in CdTe films. Although imperfect in epitaxy quality, this work demonstrates that monolayer single crystal graphene can buffer amorphous substrates for growing epitaxial films, and hence hints an opportunity for developing advanced thin film devices using graphene as a template.

36 MATERIALS SCIENCE↗