Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrical conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Domain patterning by electron beam of MgO doped lithium niobate covered by resist

Periodical domain structuring by focused electron beam irradiation of MgO-doped lithium niobate (MgOCLN) single crystalline plate covered by resist layer was studied both experimentally and by computer simulation. The dependences of domain size on the charge dose and distance between isolated domains were measured. It has been shown that the quality of periodical domain pattern depends on the thickness of resist layer and electron energy. The experimentally obtained periodic domain structures have been divided into four types. The irradiation parameters for the most uniform patterning were obtained experimentally. It was shown by computer simulation that the space charge slightly touching the crystal surface produced the maximum value of electric field at the resist/LN interface thus resulting in the best pattern quality. The obtained knowledge allowed us to optimize the poling process and to make the periodical domain patterns in 1-mm-thick wafers with an area up to 1 × 5 mm{sup 2} and a period of 6.89 μm for green light second harmonic generation. Spatial distribution of the efficiency of light frequency conversion confirmed the high homogeneity of the tailored domain patterns.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1972

Development of a multikilowatt ion thruster power processor

A feasibility study was made of the application of silicon-controlled, rectifier series, resonant inverter, power conditioning technology to electric propulsion power processing operating from a 200 to 400 Vdc solar array bus. A power system block diagram was generated to meet the electrical requirements of a 20 CM hollow cathode, mercury bombardment, ion engine. The SCR series resonant inverter was developed as a primary means of power switching and conversion, and the analog signal-to-discrete-time-interval converter control system was applied to achieve good regulation. A complete breadboard was designed, fabricated, and tested with a resistive load bank, and critical power processor areas relating to efficiency, weight, and part count were identified.

Schoenfeld, A. D.↗
NASA NTRS2008

Solid Micro Horn Array (SMIHA) for Acoustic Matching

Transduction of electrical signals to mechanical signals and vice-versa in piezoelectric materials is controlled by the material coupling coefficient. In general in a loss-less material the ratio of energy conversion per cycle is proportional to the square of the coupling coefficient. In practical transduction however the impedance mismatch between the piezoelectric material and the electrical drive circuitry or the mechanical structure can have a significant impact on the power transfer. This paper looks at novel methods of matching the acoustic impedance of structures to the piezoelectric material in an effort to increase power transmission and efficiency. In typical methods the density and acoustic velocity of the matching layer is adjusted to give good matching between the transducer and the load. The approach discussed in this paper utilizes solid micro horn arrays in the matching layer which channel the stress and increase the strain in the layer. This approach is found to have potential applications in energy harvesting, medical ultrasound and in liquid and gas coupled transducers.

power transmission↗
NASA NTRS2018

1-Watt Radioisotope Power System for Small Spacecraft

A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for small probes, landers, rovers, and communication repeaters. These missions would contain science measuring instruments that could be distributed across planetary surfaces for operation in temporarily or permanently shadowed regions. High efficiency dynamic RPS could be mission enabling for science measurements on the moon, such as collecting real-time, event-based, or cumulative space radiation measurements including primary galactic cosmic rays (GCR), solar particle events (SPE), and secondary particles liberated during atmospheric and/or surface reactions. Small RPS would use fractional versions of the General Purpose Heat Source (GPHS) or Light Weight Radioisotope Heater Units (LWRHU), to heat the power conversion technologies. Capable of three to four times higher conversion efficiency than static technologies, dynamic RPS would provide an equal amount of power using less fuel or more power using an equal amount of fuel. Providing spacecraft with more power could decrease duty cycling of basic functions and increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial concept would convert eight Watts of heat to one Watt of electrical power output for science instruments and communication. The initial design, called Small Stirling Technology Exploration Power (smallSTEP), is 11 cm diameter X 32 cm long, weighs around 3 kg, and could be used to charge batteries or capacitors for higher power burst usage. Development of the 1-watt RPS includes maturation of a Stirling engine and linear alternator, an electronics controller, and an evacuated metal foil insulation package. Test hardware and facilities are being prepared for initial demonstration of the subassemblies in a laboratory environment.

Wilson, Scott↗
DOE OSTI2021

Small-Scale Engineered High Flexibility Gasifier

This project advances a small-scale gasification unit as the first step in syngas-based hydrogen, chemicals, and synthetic fuels production. This unit is associated with an enhanced flexibility to different carbonaceous feedstocks including different types of coals, biomass, and plastics. The purpose of the project was to demonstrate feasibility and efficiency of coal pyrolysis in an auger reactor (pyrolyzer); supplemental methane and pyrolysis gas conversion into syngas in a proprietary non-catalytic converter; combined performance of pyrolyzer and non-catalytic converter to convert coal into syngas The proposed technology is based on an application of an intermediate speed pyrolysis at the temperature range 400-600°C as the first stage of biomass processing. At an industrial scale, an incorporation of coal pyrolysis into a feeding machine – auger-reactor allows to decrease its capital cost. At a pilot scale, it permits to employ electricity to build a compact device for testing of downstream equipment. The auger-reactor (pyrolyzer) generates pyrolysis gas and char practically from any carbonaceous feedstocks but their compositions and quantities are determined by their types. Pyrolysis gas is converted into syngas (mix of H 2 and CO) in a novel, proprietary hydrogen flame assisted non-catalytic converter which employs O 2 instead of air as an oxidizer. This reactor (converter) allows an easy adjustment to different pyrolysis gas compositions and tolerates a presence of sulfur and nitrogen contaminants. Our technology assumes carbonaceous feedstocks gasification with oxygen to allow the products H 2 , CO or CO 2 to be not diluted in N 2 and ready for the following synthesis of chemicals and fuels. Due to the same reason, it permits a more efficient CO 2 capture for its transport and storage. An implementation of our small-scale gasification process may overcome economic constrains by a flexible acceptance of coal, biomass, and plastics as well as their unsorted mixtures to make syngas for the following production of pure hydrogen, chemical and/or synthetic fuels.

42 ENGINEERING↗
NASA NTRS1991

Solar powered Stirling cycle electrical generator

Under NASA's Civil Space Technology Initiative (CSTI), the NASA Lewis Research Center is developing the technology needed for free-piston Stirling engines as a candidate power source for space systems in the late 1990's and into the next century. Space power requirements include high efficiency, very long life, high reliability, and low vibration. Furthermore, system weight and operating temperature are important. The free-piston Stirling engine has the potential for a highly reliable engine with long life because it has only a few moving parts, non-contacting gas bearings, and can be hermetically sealed. These attributes of the free-piston Stirling engine also make it a viable candidate for terrestrial applications. In cooperation with the Department of Energy, system designs are currently being completed that feature the free-piston Stirling engine for terrestrial applications. Industry teams were assembled and are currently completing designs for two Advanced Stirling Conversion Systems utilizing technology being developed under the NASA CSTI Program. These systems, when coupled with a parabolic mirror to collect the solar energy, are capable of producing about 25 kW of electricity to a utility grid. Industry has identified a niche market for dish Stirling systems for worldwide remote power application. They believe that these niche markets may play a major role in the introduction of Stirling products into the commercial market.

Shaltens, Richard K.↗
DOE OSTI2019

Simulation of double buffer layer on CIGS solar cell with SCAPS software

In a CIGS thin film solar cell, the buffer layer is interposed between the absorber layer and the window layer, which plays an important role in interface electricity. CdS is often used as a buffer layer in CIGS cells. Beside the toxicity of Cd, the main drawback of CdS is its relatively narrow band gap (2.4 eV), which can lead to the current loss due to parasitic absorption. In order to reduce the use of CdS, we try other buffer layers instead of CdS and optimize buffer layer structure. Numerical simulation has been used to explore the effect of different buffer layer materials (CdS and ZnSe) on the performance of CuInGaSe{sub 2} solar cells with SCAPS-1D software. The main photovoltaic parameters of the analog device: open circuit voltage, short circuit current density, fill factor and conversion efficiency (η) were compared and analyzed. The results show that different buffer materials and thickness have great influence on the performance of the cell. In this simulation, CdS buffer layer was replaced by ZnSe material, which has a wider band gap. However, the efficiency of this kind of cell is lower than that of CIGS device with CdS buffer layer because of the bad energy band alignment. In order to improve the short-wave absorption and the efficiency of CIGS cell, we simulated a novel CdS/ZnSe double buffer layer structure. The efficiency of the optimized cell with double buffer layer increases from 18.47% (conventional cell with the same CdS buffer layer thickness) to 19.01%.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Electrolyzer energy dominates separation costs in state-of-the-art CO 2 electrolyzers: Implications for single-pass CO 2 utilization

In low-temperature CO 2 electrolysis, a fundamental trade-off exists between maximizing electrolyzer performance and minimizing downstream CO 2 recovery. Here, by coupling a down-the-gas-channel electrolyzer model with a techno-economic analysis, we find that the optimal single-pass CO 2 conversion for ethylene production is typically low—on the order of 5%–10%—although larger optima are found if the H 2 faradic efficiency is very low. Similarly, strategies for eliminating carbonate crossover require more energy than downstream gas separation if they increase the cell potential by ~0.2 V; however, when CAPEX are accounted for, this “break-even” voltage increases to ~ 0.4 to 0.8 V for electricity prices varying from 6c/kWh to 1.5c/kWh. These findings are a consequence of the low energy requirements of industrial gas separation relative to electrochemical CO 2 reduction. Under most circumstances, maintaining near-optimal electrolyzer performance is more important than reducing or eliminating downstream gas separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Highly Selective Electrocatalytic Reduction of CO 2 into Methane on Cu–Bi Nanoalloys

Methane (CH 4 ), the main component of natural gas, is one of the most valuable products facilitating energy storage via electricity conversion. However, the poor selectivity and high overpotential for CH 4 formation with metallic Cu catalysts prevent realistic applications. Introducing a second element to tune the electronic state of Cu has been widely used as an effective method to improve catalytic performance, but achieving high selectivity and activity toward CH 4 remains challenging. Here, we successfully synthesized Cu–Bi NPs, which exhibit a CH 4 Faradaic efficiency (FE) as high as 70.6% at -1.2 V versus reversible hydrogen electrode (RHE). The FE of Cu–Bi NPs has increased by approximately 25-fold compared with that of Cu NPs. DFT calculations showed that alloying Cu with Bi significantly decreases the formation energy of *COH formation, the rate-determining step, which explains the improved performance. Further analysis showed that Cu that has been partially oxidized because of electron withdrawal by Bi is the most possible active site.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

High-performance photonic transformers for DC voltage conversion

Abstract Direct current (DC) converters play an essential role in electronic circuits. Conventional high-efficiency DC voltage converters, especially step-up type, rely on switching operation, where energy is periodically stored within and released from inductors and/or capacitors connected in a variety of circuit topologies. Since these energy storage components, especially inductors, are fundamentally difficult to scale down, miniaturization of switching converters proves challenging. Furthermore, the resulting switching currents produce significant electromagnetic noise. To overcome the limitations of switching converters, photonic transformers, where voltage conversion is achieved through light emission and detection processes, have been demonstrated. However, the demonstrated efficiency is significantly below that of the switching converter. Here we perform a detailed balance analysis and show that with a monolithically integrated design that enables efficient photon transport, the photonic transformer can operate with a near-unity conversion efficiency and high voltage conversion ratio. We validate the theory with a transformer constructed with off-the-shelf discrete components. Our experiment showcases near noiseless operation and a voltage conversion ratio that is significantly higher than obtained in previous photonic transformers. Our findings point to the possibility of a high-performance optical solution to miniaturizing DC power converters and improving the electromagnetic compatibility and quality of electrical power.

42 ENGINEERING↗
NASA NTRS1975

High-efficiency graded band-gap Al/x/Ga/1-x/As-GaAs solar cell

A detailed theoretical analysis of an n-on-p graded band-gap Al(x)Ga(1-x)As-GaAs solar cell yields a maximum air mass zero power conversion efficiency of 17% compared to 9% for a similar GaAs cell. The analysis includes surface and bulk minority carrier recombination, junction recombination current, spectrally varying surface reflection, and series resistance loss. The maximum efficiency is determined for a surface recombination velocity of 10,000 cm/sec and hole and electron diffusion lengths of 2.1 and 7.6 microns, respectively. The improved efficiency is primarily due to a built-in electric field, caused by the band-gap gradation, accelerating photogenerated holes toward the p-n junction. This field reduces the surface and bulk recombination of the holes, and thereby enhances their collection.

Hutchby, J. A.↗
DOE OSTI2016

Enhancement of photovoltaic effects and photoconductivity observed in Co-doped amorphous carbon/silicon heterostructures

Co-doped amorphous carbon (Co-C)/silicon heterostructures were fabricated by growing Co-C films on n-type Si substrates using pulsed laser deposition. A photovoltaic effect (PVE) has been observed at room temperature. Open-circuit voltage V{sub oc} = 320 mV and short-circuit current density J{sub sc }= 5.62 mA/cm{sup 2} were measured under illumination of 532-nm light with the power of 100 mW/cm{sup 2}. In contrast, undoped amorphous carbon/Si heterostructures revealed no significant PVE. Based on the PVE and photoconductivity (PC) investigated at different temperatures, it was found that the energy conversion efficiency increased with increasing the temperature and reached the maximum at room temperature, while the photoconductivity showed a reverse temperature dependence. The observed competition between PVE and PC was correlated with the way to distribute absorbed photons. The possible mechanism, explaining the enhanced PVE and PC in the Co-C/Si heterostructures, might be attributed to light absorption enhanced by localized surface plasmons in Co nanoparticles embedded in the carbon matrix.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Roadmap on energy harvesting materials

Ambient energy harvesting has great potential to contribute to sustainable development and address growing environmental challenges. Converting waste energy from energy-intensive processes and systems (e.g. combustion engines and furnaces) is crucial to reducing their environmental impact and achieving net-zero emissions. Compact energy harvesters will also be key to powering the exponentially growing smart devices ecosystem that is part of the Internet of Things, thus enabling futuristic applications that can improve our quality of life (e.g. smart homes, smart cities, smart manufacturing, and smart healthcare). To achieve these goals, innovative materials are needed to efficiently convert ambient energy into electricity through various physical mechanisms, such as the photovoltaic effect, thermoelectricity, piezoelectricity, triboelectricity, and radiofrequency wireless power transfer. By bringing together the perspectives of experts in various types of energy harvesting materials, this Roadmap provides extensive insights into recent advances and present challenges in the field. Additionally, the Roadmap analyses the key performance metrics of these technologies in relation to their ultimate energy conversion limits. Building on these insights, the Roadmap outlines promising directions for future research to fully harness the potential of energy harvesting materials for green energy anytime, anywhere.

14 SOLAR ENERGY↗
NASA NTRS2014

Lightweight, Efficient Power Converters for Advanced Turboelectric Aircraft Propulsion Systems

NASA is investigating advanced turboelectric aircraft propulsion systems that use superconducting motors to drive multiple distributed turbofans. Conventional electric motors are too large and heavy to be practical for this application; therefore, superconducting motors are required. In order to improve aircraft maneuverability, variable-speed power converters are required to throttle power to the turbofans. The low operating temperature and the need for lightweight components that place a minimum of additional heat load on the refrigeration system open the possibility of incorporating extremely efficient cryogenic power conversion technology. This Phase II project is developing critical components required to meet these goals.

Hennessy, Michael J.↗
DOE OSTI2023

Boosting the performances of protonic solid oxide fuel cells for co-production of propylene and electricity from propane by integrating thermo- and electro- catalysis

Protonic solid oxide fuel cells (p-SOFC) integrated with clean thermal energy sources are promising platforms for decarbonized chemical production in addition to power generation, such as on-purpose propylene production from propane dehydrogenation (PDH). The catalytic performance of the conventional nickel-cermet-based anode materials in p-SOFC for propane conversion is restrained by their low active surface area and proneness to coking. In this work, by integration of a highly efficient industry-relevant thermal catalyst PtGa/ZSM-5 for PDH reaction, we demonstrate that both the electrochemical and catalytic performance of the propane-fueled p-SOFC can be effectively enhanced. The PtGa catalyst integrated p-SOFC exhibits a peak power density of 93 mW cm -2 at 600°C, which is greater by about 100% and 50% than that without catalyst or with a perovskite-based (Pr 0.3 Sr 0.7 ) 0.9 Ni 0.1 Ti 0.9 O 3 (PSNT) catalyst layer, respectively. The PDH activity and olefin selectivity of the PtGa catalyst is also significantly higher than that of the PSNT catalyst. In addition, much improved coke tolerance and propylene selectivity (over 90%) compared to the catalyst-free Ni-cermet anode materials were achieved by integrating the industrial catalyst layer. The propane conversion can be further improved by an applied current density, whereas the olefin selectivity is almost unaltered. The excellent performance of the PtGa catalyst integrated p-SOFC is attributed to the high surface area, intrinsically high catalytic activity, selectivity, and anti-coking properties of the catalytic layer for propane conversion. In conclusion, this work provides a general approach and a case study for boosting the performances of p-SOFCs in chemical production by integrating thermo- and electro- catalysis.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2015

Dense electron-positron plasmas and gamma-ray bursts generation by counter-propagating quantum electrodynamics-strong laser interaction with solid targets

We use quantum electrodynamics (QED) particle-in-cell simulations to investigate and compare the generation of dense electron-positron plasmas and intense γ-ray bursts in the case of counter-propagating laser solid interaction (two-side irradiation) and single laser solid interaction (one-side irradiation). In the case of counter-propagating linearly polarized laser pulses irradiating a thin aluminum foil with each pulse peak power of 12.5 PW (I = 4 × 10{sup 23 }W/cm{sup 2}), we calculate that about 20% of the laser energy is converted into a burst of γ-rays with flux exceeding 10{sup 14 }s.{sup −1} This would be one of the most intense γ-ray sources among those currently available in laboratories. The γ-ray conversion efficiency in the case of two-side irradiation is three times higher than in the case of one-side irradiation using a single 12.5 PW laser. Dense electron-positron plasma with a maximum density of 6 × 10{sup 27 }m{sup −3} are generated simultaneously during the two-side irradiation which is eightfold denser compared to the one-side irradiation. The enhancement of the effects in the case of counter-propagating lasers are the results of the symmetrical compression of the foil target and the formation of electric potential and standing wave around the target. Realizing experimentally the proposed counter-propagating QED-strong laser-solid interaction to produce dense electron-positron pairs and prolific γ-rays will be made possible by the Extreme Light Infrastructure-Nuclear Physics facility under construction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

A novel PEMEC with 3D printed non-conductive bipolar plate for low-cost hydrogen production from water electrolysis

For establishing the large-scale hydrogen production as energy carrier from water electrolysis, improving cost-effectiveness and efficiency remains the main challenges. In this study, we propose a novel proton exchange membrane electrolyzer cell (PEMEC), consisting of non-conductive bipolar plates (BPs) and thin film liquid/gas diffusion layers (TF-LGDLs) to reduce the cost and improve the PEMEC performance. The 3D printed non-conductive BP is manufactured with low-cost polylactic acid (PLA) and is mainly functioned to distribute the water and gas products. A titanium thin film LGDL (TF-LGDL) with surroundings is developed for directly transporting electrons from the external power sources, which changes the electron transport path in the PEMECs. The PLA BP exhibits an extremely low cost (1/10 of that of the graphite BP), and the hydrogen production rate per unit BP cost in a PEMEC with PLA BP, is almost 6 times higher than a conventional one with graphite BPs. More importantly, the PEMECs with PLA BPs can achieve a good electrochemical performance of 2.21 V at 1 A/cm 2 under room temperature. A model is also developed to investigate the impact of the BP resistivity of on the cell performance, and a guideline for the selection guideline of conductivity of BPs material is provided. The easily accessible and low-cost PLA BPs coupled with the new electron-conducting path will drive the exploration of plastic materials for economic and efficient water splitting or other energy conversion devices, including fuel cells, batteries, and solar cells.

09 BIOMASS FUELS↗
DOE OSTI2025

Assessing electrification readiness in U.S. single-family homes based on a nationwide survey of electrical panel capacities

Electrification of residential buildings is a key strategy for increasing the use of renewable energy sources. Central to this transition is understanding the capacity of existing electrical infrastructure—specifically electrical panels—to safely and effectively manage increased electricity demands from electrification technologies. However, comprehensive nationwide data on electrical panel capacities in U.S. single-family homes is currently lacking. To address this gap, we conducted a nationwide survey of single-family homes, collecting detailed data on electrical panel capacities, breaker slot availability, major electric and gas appliances, electrical panel models, and home characteristics such as construction year and floor area. Photographic documentation was used to verify electrical panel data and appliance information. Results show that approximately 60% of surveyed homes have electrical panels rated at ≥200 amperes (A), indicating that a significant portion of the existing housing stock can accommodate additional electric loads. However, 31% of homes possess panels rated at ≤100 A, potentially restricting their ability to adopt new electric appliances without significant upgrades. Panel capacities positively correlate with both home size and construction year, with newer and larger homes generally better suited for electrification. Homes with higher-capacity panels tend to have fewer gas appliances, reflecting a gradual shift toward electric technologies. Conversely, homes with lower-capacity panels frequently rely on multiple gas appliances, highlighting substantial electrification challenges. Additionally, approximately 3% of surveyed homes had potentially hazardous electrical panel models, emphasizing important safety considerations in the residential electrification process. Our findings underscore the need for targeted policies, financial incentives, and infrastructure investments designed specifically to address infrastructural and safety barriers, particularly in older and smaller homes, to support equitable and efficient electrification across the U.S. residential sector.

Gul, Sadia↗