Search NASA⌕ Search

SEARCH · Search NASA

Results for “force method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Some experience using subcritical response methods in wind-tunnel flutter model studies

Experiences obtained with four methods of predicting flutter of wind-tunnel models from subcritical response data are described. The four methods are: co/quad, randomdec, power spectra density, and the peak-hold spectrum. Model excitation techniques included both forced (sinusoidal sweep) and random (tunnel turbulence). These methods were successfully used to measure the frequency and damping (or an inverse response amplitude proportional to the damping) in the predominant flutter modes. Implementation and application of each method are discussed. Some results and comparisons between methods are presented.

Foughner, J. T., Jr.↗
NASA NTRS1992

Models of convection-driven tectonic plates - A comparison of methods and results

Recent numerical studies of convection in the earth's mantle have included various features of plate tectonics. This paper describes three methods of modeling plates: through material properties, through force balance, and through a thin power-law sheet approximation. The results obtained are compared using each method on a series of simple calculations. From these results, scaling relations between the different parameterizations are developed. While each method produces different degrees of deformation within the surface plate, the surface heat flux and average plate velocity agree to within a few percent. The main results are not dependent upon the plate modeling method and herefore are representative of the physical system modeled.

King, Scott D.↗
NASA NTRS1998

Adaptation in a rotating artificial gravity environment

The centripetal force generated by a rotating space vehicle is a potential source of artificial gravity. Minimizing the cost of such a vehicle dictates using the smallest radius and highest rotation rate possible, but head movements made at high rotation rates generate disorienting, nauseogenic cross-coupled semicircular canal stimulation. Early studies suggested 3 or 4 rpm as the highest rate at which humans could adapt to this vestibular stimulus. These studies neglected the concomitant Coriolis force actions on the head/neck system. We assessed non-vestibular Coriolis effects by measuring arm and leg movements made in the center of a rotating room turning at 10 rpm and found that movement endpoints and trajectories are initially deviated; however, subjects readily adapt with 10-20 additional movements, even without seeing their errors. Equilibrium point theories of motor control errantly predict that Coriolis forces will not cause movement endpoint errors so that subjects will not have to adapt their reaching movements during rotation. Adaptation of movement trajectory acquired during Coriolis force perturbations of one arm transfers to the unexposed arm but there is no intermanual transfer of endpoint adaptation indicating that neuromotor representations of movement endpoint and trajectory are separable and can adapt independently, also contradictory to equilibrium point theories. Touching a surface at the end of reaching movements is required for complete endpoint adaptation in darkness but trajectory adapts completely with or without terminal contact. We have also made the first kinematic measurements of unconstrained head movements during rotation, these movements show rapid adaptation to Coriolis force perturbations. Our results point to methods for achieving full compensation for rotation up to 10 rpm. Copyright 1998 Published by Elsevier Science B.V.

Non-NASA Center↗
NASA NTRS1924

The Aerodynamic Forces on Airship Hulls

This report describes the new method for making computations in connection with the study of rigid airship, which was used in the investigation of the navy's ZR-1 by the special subcommittee of the National Advisory Committee for Aeronautics appointed for this purpose. It presents the general theory of the air forces on airship hulls of the type mentioned, and an attempt has been made to develop the results from the very fundamentals of mechanics without reference to some of the modern highly developed conceptions, which may not yet be thoroughly known to readers uninitiated into modern aerodynamics, and which may, perhaps, for all time remain restricted to a small number of specialists.

Munk, Max M↗
DOE OSTI2020

Continuous-Flow Centrifugal Solid/Liquid Separation for the Recovery of Rare-Earth Elements Containing Particles from Phosphoric Acid Sludge

Phosphoric acid sludge contains acid (~54% P 2 O 5 ) and solid precipitates including rare earth elements (REEs) at concentrations of ~2200 ppm. Low-cost recovery of valuable P 2 O 5 and simultaneous solid separation could be an economically feasible approach to recovering REEs while increasing the production of phosphoric acid. The sludge, however, is a complicated stream that cannot be separated by traditional technologies because of high viscosity and a large solid content (30–40%). Guided by a force balance model, an efficient solid/liquid separation method is demonstrated, using a continuous-flow centrifugal contactor. Additionally, the shear regime is bypassed by introducing the sludge directly into the rotor where a centrifugal force is exerted on the fluid, inducing phase separation. Solid particles are trapped in the contactor. High liquid recovery is demonstrated and the effects of process parameters on solid capture are investigated. Three contactors in series yield 94% recovery of solids containing 1500–2895 ppm of REEs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1979

Agard Two-Dimensional Aeroelastic Configurations

The development of reliable, efficient methods for the calculation of unsteady aerodynamic forces in the frequency-critical transonic speed regime can be enhanced by the availability of a limited number of test cases for the comparison of competing methods. Seven test cases are presented for airfoils with thickness from 6.0% to 16.5%: a biconvex parabolic arc airfoil, three conventional airfoils, and three cambered supercritical airfoils. The aerodynamic conditions such as Mach number, mean angle of attack, and oscillation amplitude and frequency are also given. Recommendations are made for uniformity in definition and reporting to enhance desired comparison for the aeroelastician.

S R Bland↗
NASA NTRS2002

Flexible substrata for the detection of cellular traction forces

By modulating adhesion signaling and cytoskeletal organization, mechanical forces play an important role in various cellular functions, from propelling cell migration to mediating communication between cells. Recent developments have resulted in several new approaches for the detection, analysis and visualization of mechanical forces generated by cultured cells. Combining these methods with other approaches, such as green-fluorescent protein (GFP) imaging and gene manipulation, proves to be particularly powerful for analyzing the interplay between extracellular physical forces and intracellular chemical events.

Review, Tutorial↗
DOE OSTI2018

Force Matching Approaches to Extend Density Functional Theory to Large Time and Length Scales

We present methods for the creation of semi-empirical quantum approaches and reactive force fields through force matching to quantum simulation data for materials under reactive conditions. Our methodologies overcome the extreme computational cost of standard Kohn-Sham Density Functional Theory (DFT) by mapping DFT computed simulation data onto functional forms with linear dependence on their parameters. This allows for quick parameterization of our models by avoiding the non-linear fitting bottlenecks associated with most molecular dynamics model development. We illustrate our approach with two different systems: (i) determination of density functional tight binding models for aqueous glycine dimerization, and (ii) determination of the Chebyshev Interactional Model for Efficient Simulation (ChIMES) reactive force field for metallic liquid carbon. In each case, we observe that our approach is easy to parametrize and yields a model that is orders of magnitude faster than DFT while largely retaining its accuracy. Overall, our methods have potential use for studying complex long time and length scale chemical reactivity at extreme conditions, where there is a significant need for computationally efficient atomistic simulations methods to aid in the interpretation and design of experiments.

Lindsey, R.↗
NASA NTRS1990

Evaluation of finite-element models and stress-intensity factors for surface cracks emanating from stress concentrations

A re-evaluation of the 3-D finite-element models and methods used to analyze surface crack at stress concentrations is presented. Previous finite-element models used by Raju and Newman for surface and corner cracks at holes were shown to have ill-shaped elements at the intersection of the hole and crack boundaries. Improved models, without these ill-shaped elements, were developed for a surface crack at a circular hole and at a semi-circular edge notch. Stress-intensity factors were calculated by both the nodal-force and virtual-crack-closure methods. Comparisons made between the previously developed stress-intensity factor equations and the results from the improved models agreed well except for configurations with large notch-radii-to-plate-thickness ratios. Stress-intensity factors for a semi-elliptical surface crack located at the center of a semi-circular edge notch in a plate subjected to remote tensile loadings were calculated using the improved models.

Tan, P. W.↗
DOE OSTI2018

Few-nucleon and many-nucleon systems with semilocal coordinate-space regularized chiral nucleon-nucleon forces

We employ a variety of ab initio methods, including Faddeev-Yakubovsky equations, no-core configuration interaction approach, coupled-cluster theory, and in-medium similarity renormalization group, to perform a comprehensive analysis of the nucleon-deuteron elastic and breakup reactions and selected properties of light and medium-mass nuclei up to 48 C a using the recently constructed semilocal coordinate-space regularized chiral nucleon-nucleon potentials. We compare the results with those based on selected phenomenological and chiral EFT two-nucleon potentials, discuss the convergence pattern of the chiral expansion, and estimate the achievable theoretical accuracy at various chiral orders using an approach to quantify truncation errors of the chiral expansion without relying on cutoff variation. We also address the robustness of this method and explore alternative ways to estimate the theoretical uncertainty from the truncation of the chiral expansion.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1978

Wing analysis using a transonic potential flow computational method

The ability of the method to compute wing transonic performance was determined by comparing computed results with both experimental data and results computed by other theoretical procedures. Both pressure distributions and aerodynamic forces were evaluated. Comparisons indicated that the method is a significant improvement in transonic wing analysis capability. In particular, the computational method generally calculated the correct development of three-dimensional pressure distributions from subcritical to transonic conditions. Complicated, multiple shocked flows observed experimentally were reproduced computationally. The ability to identify the effects of design modifications was demonstrated both in terms of pressure distributions and shock drag characteristics.

Henne, P. A.↗
NASA NTRS1982

Static calibration for measurement of loads in wind tunnel tests on Shuttle surface tiles

A description is given of the procedures used for the static calibrations of the Coe (1981) sensor array to determine normal force, pitching moment, and rolling moment from the ensemble of sensor outputs. The use of independent data to confirm the validity of the calibration is also described. Two methods are used in calibrating the Coe sensors. In the first, calibration loads and readings are arranged in matrix form and are assumed to be related in a linear fashion. In the second, each Coe sensor reading is regarded as a sum of contributions from each of the calibration loads. It is shown that the Coe load sensors, in conjunction with either of two data analysis methods, can be used to determine the forces and moments experienced by a Shuttle TPS tile.

Rummler, D. R.↗
NASA NTRS2011

Method for Cleanly and Precisely Breaking Off a Rock Core Using a Radial Compressive Force

The Mars Sample Return mission has the goal to drill, break off, and retain rock core samples. After some results gained from rock core mechanics testing, the realization that scoring teeth would cleanly break off the core after only a few millimeters of penetration, and noting that rocks are weak in tension, the idea was developed to use symmetric wedging teeth in compression to weaken and then break the core at the contact plane. This concept was developed as a response to the break-off and retention requirements. The wedges wrap around the estimated average diameter of the core to get as many contact locations as possible, and are then pushed inward, radially, through the core towards one another. This starts a crack and begins to apply opposing forces inside the core to propagate the crack across the plane of contact. The advantage is in the simplicity. Only two teeth are needed to break five varieties of Mars-like rock cores with limited penetration and reasonable forces. Its major advantage is that it does not require any length of rock to be attached to the parent in order to break the core at the desired location. Test data shows that some rocks break off on their own into segments or break off into discs. This idea would grab and retain a disc, push some discs upward and others out, or grab a segment, break it at the contact plane, and retain the portion inside of the device. It also does this with few moving parts in a simple, space-efficient design. This discovery could be implemented into a coring drill bit to precisely break off and retain any size rock core.

Richardson, Megan↗
DOE OSTI2021

The ABACUS cosmological N -body code

We present abacus, a fast and accurate cosmological N-body code based on a new method for calculating the gravitational potential from a static multipole mesh. The method analytically separates the near- and far-field forces, reducing the former to direct 1/r 2 summation and the latter to a discrete convolution over multipoles. The method achieves 70 million particle updates per second per node of the Summit supercomputer, while maintaining a median fractional force error of 10 -5 . We express the simulation time-step as an event-driven ‘pipeline’, incorporating asynchronous events such as completion of co-processor work, input/output, and network communication. abacus has been used to produce the largest suite of N-body simulations to date, the abacussummit suite of 60 trillion particles, incorporating on-the-fly halo finding. abacus enables the production of mock catalogues of the volume and resolution required by the coming generation of cosmological surveys.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2003

Design and Preparation of a Particle Dynamics Space Flight Experiment, SHIVA

ABSTRACT This paper describes the flight experiment, supporting ground science, and the design rationale for project SHIVA (Spaceflight Holography Investigation in a Virtual Apparatus). SHIVA is a fundamental study of particle dynamics in fluids in microgravity. Gravity often dominates the equations of motion of a particle in a fluid, so microgravity provides an ideal environment to study the other forces, such as the pressure and viscous drag and especially the Basset history force. We have developed diagnostic recording methods using holography to save all of the particle field optical characteristics, essentially allowing the experiment to be transferred from space back to earth in what we call the "virtual apparatus" for on-earth microgravity experimentation. We can quantify precisely the three-dimensional motion of sets of particles, allowing us to test and apply new analytical solutions developed by members of the team as reported in the 2001 Conference (Banff, Canada). In addition to employing microgravity to augment the fundamental study of these forces, the resulting data will allow us to quantify and understand the ISS environment with great accuracy. This paper shows how we used both experiment and theory to identify and resolve critical issues and produce an optimal the study. We examined the response of particles of specific gravity from 0.1 to 20, with radii from 0.2 to 2mm. to fluid oscillation at frequencies up to 80 Hz with amplitudes up to 200 microns. To observe some of the interesting effects predicted by the new solutions requires the precise location of the position of a particle in three dimensions. To this end we have developed digital holography algorithms that enable particle position location to a small fraction of a pixel in a CCD array. The spaceflight system will record holograms both on film and electronically. The electronic holograms can be downlinked providing real time data, essentially acting like a remote window into the ISS experimental chamber. Ground experiments have provided input to a flight system design that can meet the requirements for a successful experiment on ISS. Moreover the ground experiments have provided a definitive, quantitative observation of the Basset History force over a wide range of conditions. Results of the ground experiments, the flight experiment design, preliminary flight hardware design, and data analysis procedures are reported.

Trolinger, James↗
NASA NTRS1999

True Concurrent Thermal Engineering Integrating CAD Model Building with Finite Element and Finite Difference Methods

Thermal engineering has long been left out of the concurrent engineering environment dominated by CAD (computer aided design) and FEM (finite element method) software. Current tools attempt to force the thermal design process into an environment primarily created to support structural analysis, which results in inappropriate thermal models. As a result, many thermal engineers either build models "by hand" or use geometric user interfaces that are separate from and have little useful connection, if any, to CAD and FEM systems. This paper describes the development of a new thermal design environment called the Thermal Desktop. This system, while fully integrated into a neutral, low cost CAD system, and which utilizes both FEM and FD methods, does not compromise the needs of the thermal engineer. Rather, the features needed for concurrent thermal analysis are specifically addressed by combining traditional parametric surface based radiation and FD based conduction modeling with CAD and FEM methods. The use of flexible and familiar temperature solvers such as SINDA/FLUINT (Systems Improved Numerical Differencing Analyzer/Fluid Integrator) is retained.

Panczak, Tim↗
DOE OSTI2020

Computing Potential of the Mean Force Profiles for Ion Permeation Through Channelrhodopsin Chimera, C1C2

Umbrella sampling, coupled with a weighted histogram analysis method (US-WHAM), can be used to construct potentials of mean force (PMFs) for studying the complex ion permeation pathways of membrane transport proteins. Despite the widespread use of US-WHAM, obtaining a physically meaningful PMF can be challenging. Here, we provide a protocol to resolve that issue. Then, we apply that protocol to compute a meaningful PMF for sodium ion permeation through channelrhodopsin chimera, C1C2, for illustration.

59 BASIC BIOLOGICAL SCIENCES↗