Search NASA⌕ Search

SEARCH · Search NASA

Results for “graphite modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Compression failure of composite laminates

This presentation attempts to characterize the compressive behavior of Hercules AS-1/3501-6 graphite-epoxy composite. The effect of varying specimen geometry on test results is examined. The transition region is determined between buckling and compressive failure. Failure modes are defined and analytical models to describe these modes are presented.

Pipes, R. B.↗

Low velocity transverse impact behavior of 8-ply, graphite-epoxy laminates

This work discusses the behavior of eight-ply, quasi-isotropic, graphite epoxy laminates subjected to low velocity transverse impact loading. Large deflection theory of plates was used to predict the load-deflection characteristics during the impact event. The impact model considered that the indentation, flexural and shear stiffnesses could be represented by three-equivalent springs in series. The analysis of static and dynamic impact loading test-data concluded that the membrane parameter, beta, used in flexural stiffness relation was proportional to the square of the coefficient of restitution, e, of the impactor. Use of beta=0.443 e-squared was made in load-deflection relations to consider the drop in plate stiffness due to delamination. The results of impact tests up to impact velocity 5.3 m/sec. were found in close agreement with the predictions.

Lal, K. M.↗

Experimental evaluation of damping of graphite fiber composites

An investigation is described that was conducted to measure the damping of graphite fiber composites such as are to be used on the Hubble Space Telescope. The measurements were made on a composite cylinder under normal atmospheric conditions and in a vacuum chamber with varying thermal conditions. Such composites can outgas under vacuum conditions and this emission of trapped gases may have some influence on the material damping. Some results are presented for the damping coefficient measured under normal atmospheric conditions for a graphite fiber composite. The experimental damping data thus obtained were compared with the least square estimate obtained through a statistical analysis. The statistical analysis was based on a linear mathematical model consisting of a spring in parallel with a dashpot. It is observed that the discrepancy in the damping ratio between logarithmic decrement result and the least square fit is less than 6 percent for all the different tests made on the composite cylinder. Signal-to-noise ratio was maintained to be greater than 10.

Rao, M. D.↗

Experimental and Numerical Characterization of a Steady-State Cylindrical Blackbody Cavity at 1100 Degrees Celsius

A blackbody calibration furnace at the NASA Dryden Flight Research Center is used to calibrate heat flux gages. These gages are for measuring the aerodynamic heat flux on hypersonic flight vehicle surfaces. The blackbody is a graphite tube with a midplane partition which divides the tube into two compartments (dual cavities). Electrical resistance heating is used to heat the graphite tube. This heating and the boundary conditions imposed on the graphite tube result in temperature gradients along the walls of the blackbody cavity. This paper describes measurements made during steady-state operation and development of finite-difference thermal models of the blockbody furnace at 1100 C. Two configurations were studied, one with the blackbody outer surface insulated and the other without insulation. The dominant modes of heat transfer were identified for each configuration and the effect of variations in material properties and electric current that was passed through the blackbody were quantified.

Horn, Thomas J.↗

Test Plan for Sampling AGR-3/4 Capsule 10 Inner and Outer Rings

The Advanced Gas Reactor (AGR)-3/4 irradiation experiment is the third in a series of test irradiations performed as part of the AGR Fuel Development and Qualification Program. AGR-3/4 was designed to investigate the migration of fission products in fuel kernels, compact matrix, and reactor graphite components. The experiment consists of fuel compacts containing driver fuel particles and special “designed-to-fail” particles designed to release fission products during the irradiation, which will migrate through the surrounding cylindrical rings of compact matrix and nuclear grade graphite. Evaluation of the fission product distribution in these rings following the irradiation is a critical component of the experiment, providing data that will support refinement of fission product transport models. Following nondestructive gamma scanning of the inner and outer rings from the standard capsules and any disassembled fuel bodies (such as Capsule 4), physical samples will be taken from selected rings for subsequent analysis for fission products. This activity will provide quantitative data on the inventory and distribution of fission products at specific locations in the rings to compare with the gamma scanning data and model predictions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Metastability of diamond ramp-compressed to 2 terapascals

Carbon is the fourth-most prevalent element in the Universe and essential for all known life. In the elemental form it is found in multiple allotropes, including graphite, diamond and fullerenes, and it has long been predicted that even more structures can exist at pressures greater than those at Earth’s core. Several phases have been predicted to exist in the multi-terapascal regime, which is important for accurate modelling of the interiors of carbon-rich exoplanets. By compressing solid carbon to 2 terapascals (20 million atmospheres; more than five times the pressure at Earth’s core) using ramp-shaped laser pulses and simultaneously measuring nanosecond-duration time-resolved X-ray diffraction, we found that solid carbon retains the diamond structure far beyond its regime of predicted stability. The results confirm predictions that the strength of the tetrahedral molecular orbital bonds in diamond persists under enormous pressure, resulting in large energy barriers that hinder conversion to more-stable high-pressure allotropes, just as graphite formation from metastable diamond is kinetically hindered at atmospheric pressure. In conclusion, this work nearly doubles the highest pressure at which X-ray diffraction has been recorded on any material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The role of detonation condensates on the performance of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) detonation

Thermochemical models of detonation are widely used to estimate energy delivery, but they are based on the assumption that the carbon-rich condensates (soot) formed during detonation are very similar to bulk carbon. Here, we present an analytic equation of state (EOS) based on experimental detonation data for soot formed during the detonation of triaminotrinitrobenzene (TATB)-based high explosives. X-ray photoelectron spectra of several detonation soots are used to determine the elemental nitrogen abundance, with surprisingly high values for TATB. The proposed TATB soot EOS is highly compressible at low pressures and shares some features of glassy carbon, exhibiting graphite- and diamond-like behavior as a function of pressure. We demonstrate the influence of formed soot on detonation performance, including a lowering of the detonation velocity at typical charge densities, and a more compressive product Hugoniot at overdriven conditions. The soot model improves the accuracy of thermochemical calculations for TATB-based explosives across a wide range of states. Detonation velocity predictions for HMX (cyclotetramethylene-tetranitramine)-TATB blends with 80% or more TATB content, as well predictions for 1,3-diamino-2,4,6-trinitrobenzene (DATB) and 3-nitro-1,2,4-triazol-5-one (NTO), which share some features with TATB, are also improved.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhancing the multi-functional properties of renewable lignin carbon fibers via defining the structure–property relationship using different biomass feedstocks

Lignin has been explored extensively as a renewable precursor for carbon materials, considering its abundance as a major component of plant cell walls and its sustainability as a byproduct of both lignocellulosic biorefinery and the paper-making industry. Despite the extensive efforts to define the process–property relationship, it remains largely unknown how lignin biosynthesis and its chemistry would impact the resultant carbon fiber properties, for both mechanical and electroconductive performances. Such inadequate understanding fundamentally limits feedstock design and selection to improve carbon fiber properties toward broader commercial applications. Using lignin from a broad range of biomass feedstocks for carbon fiber manufacturing, we have fundamentally explored the structure–function relationship between lignin chemistry and carbon fiber performance. Specifically, lignin extracted from hardwood (sugar maple), softwood (loblolly pine and red cedar), and herbaceous plants (corn stover and switchgrass) was used for carbon fiber manufacturing, considering the very different lignin structures from these feedstocks. Linear regression models were established to define the relationship between carbon fiber mechanical properties and lignin structural characteristics. The results highlighted that the content of β-O-4 linkages correlates significantly with the tensile strength and elastic modulus of lignin carbon fibers, indicating that more linear β-O-4 linkages would promote the carbon fiber mechanical performance. Moreover, electroconductive properties are essential for broader energy device application of lignin-based carbon fibers, yet the mechanisms controlling their electroconductivity are largely unknown. Furthermore, we hereby demonstrated that a higher β-O-4 content also promotes the electroconductivity of lignin carbon fibers. Microstructure analysis further revealed that the crystallite size and content of the pre-graphitic turbostratic carbon structure in lignin-based carbon fibers were enhanced as the β-O-4 linkages increased. The content of β-O-4 linkages has shown a strong correlation with the crystallite content in a linear regression model. This study thus revealed the underlying mechanisms regarding how the lignin structure in planta defines the resultant carbon fiber properties. Moreover, the study also highlighted the correlation between the mechanical and electroconductive properties of lignin-based carbon fibers, both of which were defined by the lignin structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

RELICS OF ANCIENT POST-AGB STARS IN A PRIMITIVE METEORITE

Graphite is one of the many presolar circumstellar condensate species found in primitive meteorites. While the isotopic compositions of low-density graphite grains indicate an origin in core-collapse supernovae, some high-density grains have extreme isotopic anomalies in C, Ca, and Ti, which cannot be explained by envelope predictions of asymptotic giant branch (AGB) stars or theoretical supernova models. The Ca and Ti isotopic anomalies, however, match the predictions of He-shell abundances in AGB stars. In this study, we show that the C, Ca, and Ti isotopic anomalies are consistent with nucleosynthesis predictions of the H-ingestion phase during a very late thermal pulse (VLTP) event in post-AGB stars. The low {sup 12}C/{sup 13}C isotopic ratios in these grains are a result of abundant {sup 12}C efficiently capturing the protons that are being ingested during the VLTP. Very high neutron densities of ∼10{sup 15} cm{sup –3}, typical of the i-process, are achieved during this phase in post-AGB stars. The large {sup 42,43,44}Ca excesses in some graphite grains are indicative of neutron capture nucleosynthesis during VLTP. The comparison of VLTP nucleosynthesis calculations to the graphite data also indicate that apparent anomalies in the Ti isotopic ratios are due to large contributions from {sup 46,48}Ca, which cannot be resolved from the isobars {sup 46,48}Ti during the measurements. We conclude that presolar graphite grains with moderate to extreme Ca and Ti isotopic anomalies originate in post-AGB stars that suffer a VLTP.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

STUDY ON AIR INGRESS MITIGATION METHODS IN THE VERY HIGH TEMPERATURE GAS COOLED REACTOR (VHTR)

An air-ingress accident followed by a pipe break is considered as a critical event for a very high temperature gas-cooled reactor (VHTR). Following helium depressurization, it is anticipated that unless countermeasures are taken, air will enter the core through the break leading to oxidation of the in-core graphite structure. Thus, without mitigation features, this accident might lead to severe exothermic chemical reactions of graphite and oxygen. Under extreme circumstances, a loss of core structural integrity may occur along with excessive release of radiological inventory. Idaho National Laboratory under the auspices of the U.S. Department of Energy is performing research and development (R&D) that focuses on key phenomena important during challenging scenarios that may occur in the VHTR. Phenomena Identification and Ranking Table (PIRT) studies to date have identified the air ingress event, following on the heels of a VHTR depressurization, as very important (Oh et al. 2006, Schultz et al. 2006). Consequently, the development of advanced air ingress-related models and verification and validation (V&V) requirements are part of the experimental validation plan. This paper discusses about various air-ingress mitigation concepts applicable for the VHTRs. The study begins with identifying important factors (or phenomena) associated with the air-ingress accident by using a root-cause analysis. By preventing main causes of the important events identified in the root-cause diagram, the basic air-ingress mitigation ideas can be conceptually derived. The main concepts include (1) preventing structural degradation of graphite supporters; (2) preventing local stress concentration in the supporter; (3) preventing graphite oxidation; (4) preventing air ingress; (5) preventing density gradient driven flow; (4) preventing fluid density gradient; (5) preventing fluid temperature gradient; (6) preventing high temperature. Based on the basic concepts listed above, various air-ingress mitigation methods are proposed in this study. Among them, the following two mitigation ideas are extensively investigated using computational fluid dynamic codes (CFD): (1) helium injection in the lower plenum, and (2) reactor enclosure opened at the bottom. The main idea of the helium injection method is to replace air in the core and the lower plenum upper part by buoyancy force. This method reduces graphite oxidation damage in the severe locations of the reactor inside. To validate this method, CFD simulations are addressed here. A simple 2-D CFD model is developed based on the GT-MHR 600MWt design. The simulation results showed that the helium replace the air flow into the core and significantly reduce the air concentration in the core and bottom reflector potentially protecting oxidation damage. According to the simulation results, even small helium flow was sufficient to remove air in the core, mitigating the air-ingress successfully. The idea of the reactor enclosure with an opening at the bottom changes overall air-ingress mechanism from natural convection to molecular diffusion. This method can be applied to the current system by some design modification of the reactor cavity. To validate this concept, this study also uses CFD simulations based on the simplified 2-D geometry. The simulation results showed that the enclosure open at the bottom can successfully mitigate air-ingress into the reactor even after on-set natural circulation occurs.

99 GENERAL AND MISCELLANEOUS↗

Carbon Isotopic Heterogeneity of Graphite in the San Juan Mass of the Campo Del Cielo IAB Iron Meteorite

The origin of IAB iron meteorites is still a matter of debate. It is generally believed that iron meteorites originated from molten cores in small planetesimals because the fractionation trend of trace elements (e.g., Ir, Ge, Ga, etc. vs. Ni) for most iron meteorites can be more or less explained by fractional crystallization from metal melts. However, this process cannot produce trace element characteristics of the IAB (and other) iron meteorites. To explain these trace element abundance patterns, several models have been proposed. Although most of these models require a high temperature, clear evidence has recently been obtained for a sub-solidus formation of IAB iron meteorites from noble gas analyses. Moreover, heterogeneous distributions of some trace elements in metal and other phases also suggest a low temperature origin of at least some IAB iron meteorites. Here we use the carbon isotopic compositions of graphite to constrain the origin of IAB iron meteorites. Our data confirm a possible low temperature origin of IAB iron meteorites.

Maruoka, T.↗

Degradation and Modeling of Large-Format Commercial Lithium-Ion Cells as a Function of Chemistry, Design, and Aging Conditions

Demand for large-format (>10 Ah) lithium-ion batteries has increased substantially in recent years, due to the growth of both electric vehicle and stationary energy storage markets. The economics of these applications is sensitive to the lifetime of the batteries, and end-of-life can either be due to energy or power limitations. Despite this, there is little information from cell manufacturers on the sensitivity of cell degradation to environmental conditions or battery use. This work reports accelerated aging test data from four commercial large-format lithium-ion batteries from three manufacturers, with varying design (thickness, casings, ...), chemistry (lithium-iron-phosphate (LFP) or lithium-nickel-manganese-cobalt-oxide positive electrodes (NMC), with graphite (Gr) negative electrodes), and capacity (50 to 250 Amp hours). The tested LFP|Gr cell is found to be relatively insensitive to cycling conditions like temperature or voltage window, while NMC|Gr cells have varying sensitivity. Degradation trends are further investigated by training predictive models: simple polynomial trend lines, a semi-empirical reduced-order model, and an empirical reduced-order model identified using machine-learning based on symbolic regression. Calendar and cycle life are simulated over a variety of conditions to directly compare the various batteries. Cell size and thickness are found to substantially impact sensitivity to temperature during cycle aging, while electrode chemistry impacts depth-of-discharge sensitivity. Real-world battery lifetime is evaluated by simulating residential energy storage and commercial frequency containment reserve systems in several U.S. climate regions. Predicted lifetime across cell types varies from 7 years to 20+ years, though all cells are predicted to have at least 10 year life in certain conditions.

battery lifetime↗

Advanced risk assessment of the effects of graphite fibers on electronic and electric equipment

An assessment of the risk associated with accidents involving aircraft with carbon fiber composite structural components is examined. The individual fiber segments cause electrical and electronic equipment to fail under certain operating conditions. A Monte Carlo simulation model was used to computer the risk. Aircraft accidents with fire, release of carbon fiber material, entrainment of carbon fibers in a smoke plume transport of fibers downwind, transfer of some fibers/into the the interior of buildings, failures of electrical and electronic equipment, and economic impact of failures are discussed. Risk profiles were prepared for individual airports and the Nation. The vulnerability of electrical transmission equipment to carbon fiber incursion and aircraft accident total costs is investigated.

Pocinki, L.↗

Polymer surfaces graphitization by low-energy He{sup +} ions irradiation

The electrical and optical properties of surfaces of polyimide and AZ5214e graphitized by low-energy (1 keV) He{sup +} irradiation at different polymer temperatures were investigated. The conductivity of the graphitized layers can be controlled with the irradiation temperature within a broad range and can reach values up to ∼1000 S/cm. We show that the electrical transport in low-conducting samples is governed by thermally activated hopping, while the samples with a high conductivity show a typical semimetallic behavior. The transition from thermally activated to semimetallic conductance governed by the irradiation temperature could also be observed in optical measurements. The semimetallic samples show an unusually high for graphitic materials carrier concentration, which results in a high extinction coefficient in the visible light range. By analyzing the temperature dependence of the conductance of the semimetallic samples, we conclude that the scattering of charge carriers is dominated by Coulomb interactions and can be described by a weak localization model. The transition from a three to two dimensional transport mechanism at low temperatures consistently explains the change in the temperature dependence of the conductance by cooling, observed in experiments.

36 MATERIALS SCIENCE↗

A simple centrifuge cell method for ex situ quantification of electrical conductivity of slurry electrode materials

We present the design, experimental procedure, and experimental evaluation of a system for fast, simple, and ex situ characterization of electrical conductivity of slurry electrode materials. The system uses a custom-designed electrochemical cell compatible with centrifugation in a swing-bucket centrifuge. The cell features cylindrical graphite electrodes that are partially sheathed so as to expose only 2 mm of the electrode surface to the bottom region of the packed particulate pellet. Also presented is a conduction model that provides a shape factor for estimating effective conductivity. We tested aqueous solutions of carbon black (CB), activated carbon (AC), and mixtures thereof. These particles were dispersed in 0.0 and 0.5 M NaCl solutions. Measurements show that the effective conductivity initially increases linearly with pellet mass and then saturates at higher masses. Notably, CB exhibited a fivefold increase in conductivity than AC at equal pellet masses. CB/AC mixtures at a fixed pellet mass were tested with CB mass fractions of 0 to 100%. Interestingly, the mixture conductivity was found to be a non-monotonic function of CB mass fraction, with a maximum conductivity at about 60 % CB mass fraction. At this maximum, the mixture conductivity is approximately 30 % higher than pure CB. NaCl concentration in the slurry solution had no effects on conductivity. These results highlight the interactions between slurry electrode composition and compaction, offering insights for optimizing slurry electrodes. Furthermore, the system and results may also be applicable to evaluation of particulate materials (including slurries) used for Li-ion batteries, capacitive deionization, fuel cells, and flow electrodes.

Capacitive deionization↗

Phase Behavior of Methane–Ethane Mixtures in Nanopores

The behavior of fluids in confined spaces is important in several research fields, including the oil and gas industry, because of the importance of confined hydrocarbons in unconventional shale reservoirs. A large percentage of the hydrocarbons are contained in nanoscale shale pores, and as a result, interactions between fluid molecules and the pore walls become significant to the fluid behavior and cause deviations of the fluid properties from bulk properties. In this work, classical molecular dynamics (MD) simulations and grand canonical Monte Carlo (GCMC) simulations are performed to model kerogen pores in shale reservoirs and their effect on adsorption selectivity and phase equilibria of hydrocarbon mixtures in a wide range of temperatures and pressures. A slit pore made of graphite walls is used to represent the basic unit where a fluid may be stored in shale reservoirs. The separation between graphite layers is varied to observe the effect of confinement on the adsorption selectivity and phase equilibrium of methane-ethane mixtures. Results from GCMC and MD simulations show that ethane is preferred over methane in the confined system. Moreover, most fluid molecules in the confined system tend to be adsorbed on the pore walls instead of remaining in the gas phase. Preferential interactions between the fluid molecules and the pore walls induce changes in the phase diagram in the confined system. Furthermore, the results from GCMC simulations show shifts with respect to the bulk pressure-composition phase diagram that becomes more pronounced as the pore size decreases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diamagnetism and charge transfer in graphite intercalation compounds

The magnetic susceptibilities at 300 K of the acceptor-type intercalation compounds of graphite with Br2 and ICl are calculated; the results are compared with published experimental measurements in graphs; and the charge-transfer parameter f is inferred using a rigid-band model (Loughin et al., 1978; Weinberger et al., 1978; Mattix et al., 1983). Assuming a screening length of 200 pm, the values determined are f = 0.3 for C(8N)Br2 and f = 0.09 for C(13N)ICl.

Tsang, T.↗

What predictions can be made on the nature of carbon and carbon-bearing compounds (hydrocarbons) in the interstellar medium based on studies of interplanetary dust particles?

The nature of hydrocarbons and properties of elemental carbon in circumstellar, interstellar, and interplanetary dust is a long standing problem in astronomy and meteorite research. The textures and crystallographical properties of poorly graphitized carbon (PGC) from carbonaceous chondrites and Chondritic Porous Aggregates (CPAs) are comparable with PGCs formed by dehydrogenation and carbonization of hydrocarbon precursors under natural terrestrial and experimental conditions. A multistage model of hydrocarbon diagenesis in CPA and carbonaceous chondrite (proto-) planetary parent bodies was proposed in which hydrocarbons are subjected to low temperature hydrous pyrolysis. Continued efforts to recognize hydrocarbons and elemental phases in CPAs may allow understanding of the multistage hydrocarbon/elemental carbon model.

Rietmeijer, F. J. M.↗