Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Erosion of tungsten marker layers in W7-X

In order to get first insight into net tungsten erosion in W7-X, tungsten (W) marker layers were exposed during the operational phase OP 1.2b at one position of the Test Divertor Unit (TDU), at 21 different positions of the inner heat shield, and at two scraper elements. The maximum tungsten erosion rate at the TDU strike line was 0.13 nm s -1 averaged over the whole campaign. The erosion was inhomogeneous on a microscopic scale, with higher erosion on ridges of the rough surface inclined towards the plasma and deposition of hydrocarbon layers in the recessed areas of the rough surface. The W erosion at the inner heat shield was below the detection limit of 3–6 × 10 12 W-atoms/cm 2 s, and all inner heat shield tiles were covered with a thin B/C/O layer with thickness in the range 2 × 10 17 –10 18 B + C atoms/cm 2 (about 20–100 nm B + C). W-erosion of the marker layers on the scraper elements was also below the detection limit.

Mayer, M↗

Influence of deposition pressure and pulsed dc sputtering on pumping properties of Ti-Zr-V nonevaporable getter films

The performance of a UHV vessel can be improved with a new CERN technology nonevaporable getter (NEG) coating, which is already widely used for accelerator vacuum chambers. Better understanding of the processes involved in NEG film deposition, activation, and poisoning should allow optimization and engineering of the film properties, which are necessary for a particular application. Ti-Zr-V NEG films were created by magnetron sputtering from a single Ti-Zr-V target, and the NEG performance and morphology dependence on deposition pressure, sputtering conditions, and substrate surface roughness have been investigated. It was found that the average grain size of the Ti-Zr-V film was 5-6 nm and was broadly independent of the substrate material and deposition conditions. However, film topography and density were shown to depend very much on the substrate surface roughness and deposition conditions. Rough substrates, high working pressures, and the absence of ion bombardment produced open columnar structures, whereas smooth substrates, ion assistance, and low pressures produced much denser layers. X-ray photoelectron spectroscopy studies have shown that full regeneration occurred at 300 degree sign C but film activation started at temperatures of as low as 160 degree sign C. The CO sticking probability reaches its maximum after activation at 250 degree sign C and is found to be up to 0.3 with a pumping capacity in the range of 0.8-1.2 ML. The samples activated at 160 degree sign C have a reduced pumping speed and capacity by an order of magnitude.

36 MATERIALS SCIENCE↗

Investigations of lubricant rheology as applied to elastohydrodynamic lubrication

Traction prediction in sliding elastohydrodynamic (EHD) contacts was examined along with an elastohydrodynamic lubrication simulation of the effects of load and speed on temperatures in the EHD contact. An existing shear stress theory and lubricant rheological model were studied and evaluated by applying them to traction prediction. Results obtained using measured film thickness and surface temperature data, were compared with measured traction values. The infrared technique for measuring temperatures in an EHD contact was further developed and ball surface and fluid temperatures are reported for sliding speeds of 0.35 to 5.08 m/s at 0.52 to 2.03 GN/sq m maximum pressure and surface roughnesses of .011 to .381 micrometers c.1.a. The relationship between asperity interaction, as measured by relocation surface profilimetry and high frequency temperature measurements, and the ratio of film thickness to surface roughness was also studied.

Kunz, R. K.↗

Optical Strain Measurement System Development

Investigations of physical phenomena affecting the durability of SSME components require measurement systems operational in hostile environments. The need for such instrumentation caused the definition and operation of an optical strain measurement system. This optical strain measurement system based on the speckle shift method is being developed. This is a noncontact, automatic method of measuring surface strain in one dimension that corrects for error due to rigid body motion. It provides a gauge length of 1 to 2 mm and allows the region of interest on the test specimen to be mapped point by point. The output is a graphics map of the points inspected on the specimen; data points is stored in quasi-real time. This is the first phase of a multiphase effort in optical strain measurement. The speckle pattern created by the test specimen is interpreted as high order interference fringes resulting from a random diffraction grating, being the natural surface roughness of the specimen. Strain induced on the specimen causes a change in spacing of the surface roughness, which in turn shifts the position of the interference pattern (speckles).

Lant, C. T.↗

Assessment of Ice Shape Roughness Using a Self-Orgainizing Map Approach

Self-organizing maps are neural-network techniques for representing noisy, multidimensional data aligned along a lower-dimensional and nonlinear manifold. For a large set of noisy data, each element of a finite set of codebook vectors is iteratively moved in the direction of the data closest to the winner codebook vector. Through successive iterations, the codebook vectors begin to align with the trends of the higher-dimensional data. Prior investigations of ice shapes have focused on using self-organizing maps to characterize mean ice forms. The Icing Research Branch has recently acquired a high resolution three dimensional scanner system capable of resolving ice shape surface roughness. A method is presented for the evaluation of surface roughness variations using high-resolution surface scans based on a self-organizing map representation of the mean ice shape. The new method is demonstrated for 1) an 18-in. NACA 23012 airfoil 2 AOA just after the initial ice coverage of the leading 5 of the suction surface of the airfoil, 2) a 21-in. NACA 0012 at 0AOA following coverage of the leading 10 of the airfoil surface, and 3) a cold-soaked 21-in.NACA 0012 airfoil without ice. The SOM method resulted in descriptions of the statistical coverage limits and a quantitative representation of early stages of ice roughness formation on the airfoils. Limitations of the SOM method are explored, and the uncertainty limits of the method are investigated using the non-iced NACA 0012 airfoil measurements.

Icing↗

Effects of Fine Particle Shot Peening Treatment on Fatigue Properties of Al-7Si-0.3Mg Alloy

In this study, two different fine particle shot peening (FPSP) treatments were performed on Al-7Si-0.3Mg alloy specimens to evaluate their effects on fatigue properties. After the treatment, the microstructure morphology of the specimens was observed, and the surface roughness and residual stress distribution were measured. Rotating bending fatigue tests were conducted, and the fatigue fracture surfaces were observed using scanning electron microscopy (SEM). The crack initiation and propagation behavior were investigated using the replica method. The results indicate that FPSP can introduce residual stress on the surface layer of the material and refine the surface microstructure, and also change the surface roughness. At low stress amplitude levels, FPSP can improve fatigue life significantly. At 5 × 10{sup 7} cycles, the fatigue strength of shot-peened specimens increased by 33% compared to unpeened specimens. In unpeened and steel shot-peened (SSP) specimens, both crystal slip and casting defects can induce fatigue failure, while only casting defects can cause failure in the case of ceramic shot-peened (CSP) specimens. Moreover, FPSP can move the crack initiation site to the subsurface from the surface. The range of threshold stress intensity factor of the material can be improved significantly by this treatment. Casting defects have a significant influence on fatigue strength; the effect on fatigue strength can be well evaluated by the modified Murakami equation.

36 MATERIALS SCIENCE↗

Effects of ion sputtering on plutonium surfaces

Scanning tunneling microscopy has been performed on an electro-polished gallium-stabilized delta-phase plutonium sample under ultra-high vacuum conditions. The images obtained were used to measure surface roughness as ion sputtering and annealing was applied to the plutonium sample. It was demonstrated that sputter/anneal cycles progressively increased the surface roughness of the plutonium. Furthermore, Auger and scanning tunneling spectroscopy measurements revealed an initially unstable and dynamically changing surface that became increasingly stable as sputter/anneal cycles were applied. The stabilized surface region contained within the sputter crater was observed to be unchanged for up to 17 months after the final sputter anneal cycle.

36 MATERIALS SCIENCE↗

Assessment of the grindability of robocast silicon carbide

The demand for high-performance lightweight optics has driven interest in silicon carbide (SiC) due to its exceptional thermal stability, hardness, and strength-to-weight ratio. This study investigates the potential of robocasting, an additive manufacturing process, as a viable method for producing lightweighted SiC components for optical applications. Four samples with varied starting powder phases (α and β) and sintering conditions were fabricated and evaluated. Post-sintering surface and form were assessed using coherence scanning interferometry (CSI) and coordinate measuring machine (CMM) techniques. A three-stage grinding process was applied to each sample, with surface roughness assessed at each stage. Results demonstrate that samples with predominantly α-phase SiC and smaller particle sizes achieved superior surface finish, particularly sample D2-α-2135 °C, which displayed the lowest post-grinding Sq value of 0.178 µm. The analysis also indicated no significant print-through effect from the lightweighting structure, or print artifacts, at this stage of grinding. However, β-phase samples showed poorer grindability, increased surface roughness, and pitting. These findings suggest that phase composition and particle size are critical for achieving the desired surface quality in robocast SiC optics. Future work will incorporate additional samples and finer grinding wheels to refine surface quality further, supporting the development of SiC for high-precision optical applications.

Barrett, Taylor [ORNL]↗

Tailoring the Surface Structures of CuPt and CuPtRu 1D Nanostructures by Coupling Coreduction with Galvanic Replacement

1D metal nanostructures exhibit unique properties due to their high aspect ratio for use in many applications including electrocatalysis. This work develops a solution-based approach to 1D multimetal nanostructures with tunable surface structures by combining the two processes of coreduction and galvanic replacement. In this approach, noble metals of Pt and Ru are reduced in the presence of in situ formed Cu seeds. At high concentrations of noble metal precursors, coreduction dominates over galvanic replacement, leading to overgrowth of ultrafine, particulate, or branched structures on the surface of the 1D nanostructures. The surface roughness and composition can be tuned by varying the concentrations of noble metal precursors. The electrochemical reactivity is not only affected by the surface roughness (i.e., the size of particulates and the level of branches) but also the surface composition (i.e., the amount of Pt content). For trimetallic nanostructures, the alloy composition prevents the dissolution of Ru thereby improving electrocatalytic stability of the catalyst under acidic conditions. Lastly, the structure–property study reveals that the surface structure plays an important role in tailoring the electrocatalytic property of a catalyst.

36 MATERIALS SCIENCE↗

Recent land cover changes in the Southwestern US lead to an increase in surface temperature

The increase in large-scale land cover change (LCC) in recent decades, particularly in response to climate-driven disturbances, has potential to impact local and regional changes in climate due to modification of carbon sources and sinks, albedo, surface roughness and energy fluxes. Using observational data, we predict the impact of two of the most extensive LCCs occurring in the Southwestern US: drought-induced tree mortality and shrub encroachment into grasslands, on surface temperature. We developed a new energy balance method that extracts the biophysical responses to environmental conditions, to predict how structural changes in albedo, surface roughness and canopy conductance following LCC will alter surface temperature. This method allows us not only to explain the observed differences in surface temperature between two non-adjacent study sites with different environmental conditions, but also to separate the contribution of biophysical and non-biophysical properties to surface temperature. Our results suggest that changes in biophysical properties due to shrub encroachment and tree mortality in the Southwestern US (independent of changes in other environmental properties) can potentially lead to an increase in midday surface temperature (11AM to 2PM) of 1 to 2 degrees Celsius, comparable to changes in surface temperature following deforestation. Although the average surface temperature increase in response to both shrub encroachment and tree mortality is similar, the biophysical properties driving the temperature change are different in each scenario. Change in aerodynamic conductance following tree mortality is the largest contributor to heating, while reduced albedo and canopy conductance drive the increase in surface temperature following shrub encroachment. Finally, we also show how this increase in daytime surface temperature could be further intensified with future climate, especially with the expected reduction in soil water availability in the Southwest.

54 ENVIRONMENTAL SCIENCES↗

Lubricant-Infused Nanoparticulate Coatings Assembled by Layer-by-Layer Deposition

Omniphobic coatings are designed to repel a wide range of liquids without leaving stains on the surface. A practical coating should exhibit stable repellency, show no interference with color or transparency of the underlying substrate and, ideally, be deposited in a simple process on arbitrarily shaped surfaces. We use layer-by-layer (LbL) deposition of negatively charged silica nanoparticles and positively charged polyelectrolytes to create nanoscale surface structures that are further surface-functionalized with fluorinated silanes and infiltrated with fluorinated oil, forming a smooth, highly repellent coating on surfaces of different materials and shapes. We show that four or more LbL cycles introduce sufficient surface roughness to effectively immobilize the lubricant into the nanoporous coating and provide a stable liquid interface that repels water, low-surface-tension liquids and complex fluids. The absence of hierarchical structures and the small size of the silica nanoparticles enables complete transparency of the coating, with light transmittance exceeding that of normal glass. The coating is mechanically robust, maintains its repellency after exposure to continuous flow for several days and prevents adsorption of streptavidin as a model protein. The LbL process is conceptually simple, of low cost, environmentally benign, scalable, automatable and therefore may present an efficient synthetic route to non-fouling materials.

Sunny, S↗

Integrating NASA Earth Science Capabilities into the Interagency Modeling and Atmospheric Assessment Center for Improvements in Atmospheric Transport and Dispersion Modeling

This report describes the development of algorithms to derive accurate surface roughness and displacement height values from NASA satellite data for both urban and vegetation environments and to evaluate the potential benefit of improved surface data characterization on atmospheric transport and dispersion modeling. One of the key factors limiting the accuracy of near-surface wind profile modeling and dispersion simulations is the lack of location-specific and seasonally-dependent surface characteristic values. Currently, land use category look-up tables are commonly used to provide grid-cell estimates of surface characteristics values, even though surface roughness values can vary significantly within the same land-use category. This report documents: i) the derivation of surface characteristic values by Goddard Space Flight Center (GSFC) and Stennis Space Center (SSC) from NASA satellite multispectral imagery, ii) their incorporation into atmospheric meteorological and transport models, and iii) the results of a dispersion modeling study for Oklahoma City and the surrounding region to evaluate the impact of GSFC/SSC roughness on National Atmospheric Release Advisory Center (NARAC) / Interagency Modeling and Atmospheric Assessment Center (IMAAC) emergency response dispersion predictions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

CRADA Number NFE-21-08827 with DayLyte, Inc. (CRADA Final Report)

DayLyte Batteries is developing an aqueous Sodium-Air battery made with abundant materials while being half to a third the weight of Li-ion to power electric aircraft, electric vehicles and provide renewable energy on demand. To make this battery practical, DayLyte is developing a thin film ceramic Nasicon solid electrolyte amenable to rapid scaleup as well as a protective coating that will protect the solid electrolyte from 50wt% NaOH during the battery’s end-of-discharge while still allowing Na-ions to pass back and forth. If the thin film solid electrolyte and stable coating can be developed it will open the world to step change in battery performance all while not sacrificing the environment on the way. The project was designed to first focus on making and characterizing the Nasicon membrane followed by measuring its electrochemical performance, then assembling a full cell, optimizing its NaOH stability and then optimize the overall prototype design. Over the past two years, we have significantly improved the Nasicon film uniformity, demonstrated protective ligands that are stable in 50wt% NaOH by measuring no mass change with a quartz crystal microbalance, tested different heating methods like tube furnace and rapid heating and developed glassy carbon coatings on the current collector to prevent Nasicon-current collector alloying. We have found that getting film uniformity as measured by electrochemical impedance spectroscopy (EIS) is difficult because of different factors like surface roughness, deposition uniformity and heat treatment time and uniformity. The glassy carbon coating should significantly reduce the surface roughness and by tuning the coating conditions the film deposition uniformity improves and using an automated heating method should lead to much improved film uniformity.

25 ENERGY STORAGE↗

Development of High Resolution Mirrors and Cd-Zn-Te Detectors for Hard X-ray Astronomy

We describe the fabrication and implementation of a high-resolution conical, grazing- incidence, hard X-ray (20-70 keV) telescope. When flown aboard stratospheric balloons, these mirrors are used to image cosmic sources such as supernovae, neutron stars, and quasars. The fabrication process involves generating super-polished mandrels, mirror shell electroforming, and mirror testing. The cylindrical mandrels consist of two conical segments; each segment is approximately 305 mm long. These mandrels are first, precision ground to within approx. 1.0 micron straightness along each conical segment and then lapped and polished to less than 0.5 micron straightness. Each mandrel segment is the super-polished to an average surface roughness of approx. 3.25 angstrom rms. By mirror shell replication, this combination of good figure and low surface roughness has enabled us to achieve 15 arcsec, confirmed by X-ray measurements in the Marshall Space Flight Center 102 meter test facility. To image the focused X-rays requires a focal plane detector with appropriate spatial resolution. For 15 arcsec optics of 6 meter focal length, this resolution must be around 200 microns. In addition, the detector must have a high efficiency, relatively high energy resolution, and low background. We are currently developing Cadmium-Zinc-Telluride fine-pixel detectors for this purpose. The detectors under study consist of a 16x16 pixel array with a pixel pitch of 300 microns and are 1 mm and 2 mm thick. At 60 keV, the measured energy resolution is around 2%.

Ramsey, Brian D.↗

A Time Series Approach for Soil Moisture Estimation

Soil moisture is a key parameter in understanding the global water cycle and in predicting natural hazards. Polarimetric radar measurements have been used for estimating soil moisture of bare surfaces. In order to estimate soil moisture accurately, the surface roughness effect must be compensated properly. In addition, these algorithms will not produce accurate results for vegetated surfaces. It is difficult to retrieve soil moisture of a vegetated surface since the radar backscattering cross section is sensitive to the vegetation structure and environmental conditions such as the ground slope. Therefore, it is necessary to develop a method to estimate the effect of the surface roughness and vegetation reliably. One way to remove the roughness effect and the vegetation contamination is to take advantage of the temporal variation of soil moisture. In order to understand the global hydrologic cycle, it is desirable to measure soil moisture with one- to two-days revisit. Using these frequent measurements, a time series approach can be implemented to improve the soil moisture retrieval accuracy.

soil moisture↗

Characterization of the alumina scale formed on a commercial MCrAlYHfSi coating

A commercial NiCoCrAlYHfSi coating deposited on a Ni-base superalloy substrate was characterized before and after high temperature oxidation. The combination of Y, Hf and Si additions are reported to improve coating performance. Advanced characterization techniques including scanning transmission electron microscopy were used to study the segregation behavior of Y and Hf ions to the alumina grain boundaries after 200h at 1050 C and 100 and 200h exposures at 1100 C. After both exposure times, two distinct oxide layers were observed. The outer transient layer included many Y- and Hf-rich oxide particles. The inner layer consisted of columnar -Al2O3 grains normal to the surface of the coating. Segregation of Y and Hf ions was found on the alumina grain boundaries as has been observed in model alloys with similar compositions. Isothermal exposures for up to 200h at 1050 and 1100 C caused a minimal increase in surface roughness. However, 200 one-hour cycles at 1100 C resulted in a more significant increase in surface roughness.

36 MATERIALS SCIENCE↗

Mask roughness induced LER: geometric model at long correlation lengths

Collective understanding of how both the resist and line-edge roughness (LER) on the mask affect the final printed LER has made significant advances. What is poorly understood, however, is the extent to which mask surface roughness couples to image plane LER as a function of illumination conditions, NA, and defocus. Recently, progress has been made in formulating a simplified solution for mask roughness induced LER. Here, we investigate the LER behavior at long correlation lengths of surface roughness on the mask. We find that for correlation lengths greater than 3/NA in wafer dimensions and CDs greater than approximately 0.75/NA, the previously described simplified model, which remains based on physical optics, converges to a 'geometric regime' which is based on ray optics and is independent of partial coherence. In this 'geometric regime', the LER is proportional to the mask slope error as it propagates through focus, and provides a faster alternative to calculating LER in contrast to either full 2D aerial image simulation modeling or the newly proposed physical optics model. Data is presented for both an NA = 0.32 and an NA = 0.5 imaging system for CDs of 22-nm and 50-nm horizontal-line-dense structures.

36 MATERIALS SCIENCE↗

Scatter of X-rays on polished surfaces

In investigating the dispersion properties of telescope mirrors used in X-ray astronomy, the slight scattering characteristics of X-ray radiation by statistically rough surfaces were examined. The mathematics and geometry of scattering theory are described. The measurement test assembly is described and results of measurements on samples of plane mirrors are given. Measurement results are evaluated. The direct beam, the convolution of the direct beam and the scattering halo, curve fitting by the method of least squares, various autocorrelation functions, results of the fitting procedure for small scattering, and deviations in the kernel of the scattering distribution are presented. A procedure for quality testing of mirror systems through diagnosis of rough surfaces is described.

Hasinger, G.↗