Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Analysis of an Arctic cold air outbreak during autumn and related air mass transformations forced by surface changes and advection in higher altitudes

During marine cold air outbreaks (MCAOs), cold and dry Arctic air masses are transported from the central Arctic southward across the closed sea ice and much warmer open oceans. They experience significant transformations including a rapid heating and moistening, often leading to cloud formation. While intense wintertime MCAOs have been analyzed widely, the air mass transformations during other seasons have been studied sparsely. We address this gap by investigating an MCAO case observed in September 2020. To study the transformation processes, we combine the fifth generation of atmospheric reanalyses of the global climate (ERA5), trajectory calculations, as well as shipborne and airborne measurements. In the central Arctic, observations acquired from aboard the research vessel (RV) Polarstern during the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition characterized the initial state of the air mass over closed sea ice. Trajectories indicated the pathway the air mass took from RV Polarstern southward to the Fram Strait. For the first 24 h of the southbound drift, the air masses remained quasi-stationary. Then, still 15 h ahead of the marginal sea ice zone, differential advection across the boundary layer flow introduced humidity and clouds at higher altitudes between 1.5 and 2.5 km. ERA5-derived temperature and humidity tendencies indicated complex vertical interactions. Radiative cloud-top cooling, entrainment, and turbulence were significantly reduced in the lower and enhanced in the upper advected cloud layer. Eventually, the lower cloud deck dissipated. After this confluence of 2 different air masses, observations gathered by Polar 5 in Fram Strait as part of the MOSAiC Airborne observations in the Central Arctic campaign revealed cloudy, moist layers throughout the lowest 3.5 km and an increasing boundary layer height. Comparing the initial with the final state 48 h later, the largest net heating of +8 K was found close to the surface, yet the largest net moistening of +2.5 g kg -1 at an altitude of 1 km, as the initial profile was exceptionally dry here. We conclude that the observed air mass transformations were driven by the surface changes from sea ice to open ocean but additionally strongly impacted by the differential advection of clouds and moisture across the near-surface MCAO flow.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2018

Very High Cycle Fatigue of a Cast Aluminum Alloy: Size Effect and Crack Initiation

Fatigue properties of an Al-Si-Cu cast alloy were investigated with life up to very high cycle fatigue regime. Particular attention was given to specimen size effect and fatigue crack initiation mechanism. Uniaxial fatigue tests with constant amplitudes were carried out by using ultrasonic fatigue testing machine operating at 20 kHz, compared to the results obtained by using conventional hydraulic fatigue machine at 35 Hz. In order to evaluate the size effect, two sets of specimens with different dimensions were used. The results show that the fatigue strength of the studied alloy decreases with the increase in specimen size. Scanning electron microscopy observation of fracture surfaces revealed that most fatigue cracks initiated from microstructural defects such as porosity located on specimen surface or in subsurface. Weibull statistical analysis of fatigue data accounting for size effect was performed to predict the fatigue life of the Al-Si-Cu alloy in the very high cycle regime. Good agreement was found between the fatigue life prediction and the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Correlated metals and unconventional superconductivity in rhombohedral trilayer graphene: A renormalization group analysis

Here, motivated by recent experimental observations of correlated metallic phases and superconductivity in rhombohedral trilayer graphene (RTG), we perform an unbiased study of electronic ordering instabilities in hole-doped RTG. Specifically, we focus on electronic states energetically proximate to Van Hove singularities (VHSs), where a large density of states promotes different interaction-induced symmetry-breaking electronic orders. To resolve the Fermi surface near VHSs, we construct a fermionic hot-spot model and demonstrate that a perpendicular electric field can tune different nesting structures of the Fermi surface. Subsequently, we apply a renormalization group analysis to describe the low-energy phase diagrams of our model under both short-range repulsive interactions as well as realistic (long-range) Coulomb interactions. Our analysis shows instabilities towards either intervalley coherent metallic phases or superconducting phases. The dominant pairing channel depends crucially on the nature of Fermi surface nesting—repulsive Coulomb interaction favors spin-singlet d-wave pairing for relatively small displacement field and spin-singlet i-wave pairing for larger displacement field. We argue that the phase diagram of RTG can be well-understood by modeling the realistic Coulomb interaction as the sum of repulsive density-density interaction and ferromagnetic spin-triplet intervalley coherence (IVC) Hund's coupling, while phonon-mediated electronic interactions have a negligible effect on this system, in sharp contrast to twisted graphene multilayers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Throughput Optimization of Molybdenum Carbide Nanoparticle Catalysts in a Continuous Flow Reactor Using Design of Experiments

Transition metal carbides (TMCs) have attracted significant attention because of their applications toward a wide range of catalytic transformations. However, the practicality of their synthesis is still limited because of the harsh conditions in which most TMCs are prepared. Recently, a solution-phase synthesis of phase-pure a-MoC1-x nanoparticles was presented. While this synthetic route yielded nanoparticles with exceptional catalytic performance, the reaction parameter space was not explored, and catalyst throughput was not optimized for scale-up. Continuous flow platforms coupled with statistical design of experiments (DoE) can provide a powerful method for understanding the reaction parameter space for optimizations. Here, we demonstrate the use of statistical DoE in tandem with response surface methodology for a parametric screening analysis to optimize the throughput of a MoC1-x nanoparticle synthesis utilizing a millifluidic flow reactor. A full factorial design was implemented to evaluate four input variables (reaction temperature, flow rate, solvent fraction of oleylamine, and precursor concentration) that carry statistically significant effects on three responses (throughput, residence time, and isolated yield). A Doehlert matrix was implemented to investigate each significant variable at a higher number of levels to optimize throughput. Our results give a nonintuitive set of experimental conditions that resulted in an optimized throughput of 2.2 g h-1. This translates to a 50-fold increase in throughput compared to the previously reported batch method. The catalytic performance of the MoC1-x nanoparticles produced under optimized throughput was demonstrated in the CO2 hydrogenation reaction. This DoE screening analysis and throughput optimization of MoC1-x synthesis open the door to an increased feasibility for scale-up.

design of experiments↗
DOE OSTI2022

Microbial Tracking-2, a metagenomics analysis of bacteria and fungi onboard the International Space Station

The International Space Station (ISS) is a unique and complex built environment with the ISS surface microbiome originating from crew and cargo or from life support recirculation in an almost entirely closed system. The Microbial Tracking 1 (MT-1) project was the first ISS environmental surface study to report on the metagenome profiles without using whole-genome amplification. The study surveyed the microbial communities from eight surfaces over a 14-month period. The Microbial Tracking 2 (MT-2) project aimed to continue the work of MT-1, sampling an additional four flights from the same locations, over another 14 months. Eight surfaces across the ISS were sampled with sterile wipes and processed upon return to Earth. DNA extracted from the processed samples (and controls) were treated with propidium monoazide (PMA) to detect intact/viable cells or left untreated and to detect the total DNA population (free DNA/compromised cells/intact cells/viable cells). DNA extracted from PMA-treated and untreated samples were analyzed using shotgun metagenomics. Samples were cultured for bacteria and fungi to supplement the above results. Staphylococcus sp. and Malassezia sp. were the most represented bacterial and fungal species, respectively, on the ISS. Overall, the ISS surface microbiome was dominated by organisms associated with the human skin. Multi-dimensional scaling and differential abundance analysis showed significant temporal changes in the microbial population but no spatial differences. The ISS antimicrobial resistance gene profiles were however more stable over time, with no differences over the 5-year span of the MT-1 and MT-2 studies. Twenty-nine antimicrobial resistance genes were detected across all samples, with macrolide/lincosamide/streptogramin resistance being the most widespread. Metagenomic assembled genomes were reconstructed from the dataset, resulting in 82 MAGs. Functional assessment of the collective MAGs showed a propensity for amino acid utilization over carbohydrate metabolism. Co-occurrence analyses showed strong associations between bacterial and fungal genera. Culture analysis showed the microbial load to be on average 3.0 × 10 5 cfu/m 2 . Utilizing various metagenomics analyses and culture methods, we provided a comprehensive analysis of the ISS surface microbiome, showing microbial burden, bacterial and fungal species prevalence, changes in the microbiome, and resistome over time and space, as well as the functional capabilities and microbial interactions of this unique built microbiome. Data from this study may help to inform policies for future space missions to ensure an ISS surface microbiome that promotes astronaut health and spacecraft integrity.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Rational Design of Novel Biomimetic Sequence-Defined Polymers for Mineralization Applications

Silica biomineralization is a naturally occurring process, wherein organisms use proteins and other biological structures to direct the formation of complex, hierarchical nanostructures. Discovery and characterization of such proteins and their underlying mechanisms spurred significant efforts to identify routes for biomimetic mineralization that reproduce the exquisite shapes and size selectivities found in nature. A common strategy has been the use of short peptide sequences with chemistry mimicking those found in natural systems, such as the use of the silaffin-derived R5 peptide. While progress has been made using this approach, there are many limitations that have prevented breakthroughs in biomimicry. To advance our ability to use charged macromolecules for silica formation, we propose to use sequence-defined synthetic polymers known as peptoids, or N-substituted polyglycines, which present significant capability for the precise tuning of sequence and structure beyond what can often be achieved with peptides alone. This study presents a computationally predicted design of these polymers that leads to the controlled formation of silica nanomaterials. We investigate surface adsorption and the mineralization process through analysis of binding mechanisms and energetics of the R5 system. Next, we synthesized two R5-inspired peptoids and validated our prediction in the design of mineralization polymers through characterization using surface plasmon resonance and electron microscopy. Here, this computationally guided study holds great promise for designing new sequences with unprecedented control of the placement of chemical functional groups, thus allowing for further unraveling of silicification mechanisms and the eventual design of sequence-defined synthetic polymers leading to the predictive synthesis of nanostructured functional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Galvanostatic Intermittent Titration Technique Reinvented: Part I. A Critical Review

The galvanostatic intermittent titration technique (GITT), introduced in 1977 by Weppner and Huggins, provided a readily accessible means to measuring the chemical diffusion coefficient of electrochemical electrode materials. The method continues to be widely used today, but the reported diffusivity values are highly inconsistent, ranging as much as four orders of magnitude for some Li layered oxide compositions. Even qualitative trends of diffusivity are inconsistent, suggesting significant flaws in the implementation of the method. Other variants of the GITT method also suffer from similar inconsistency problems. Here we identify numerous sources of significant error including composition-dependent reaction overpotentials, mathematical flaws in the relaxation analysis methods, finite-size and non-planar geometry effects, inter-particle inhomogeneity issues, early transient effects, and surface area uncertainties. We propose a simple relaxation analysis scheme using the time variable t relax + τ - t relax , where t relax is relaxation time and τ is the galvanostatic pulse duration. We also propose to use dense diffusion-limited samples to isolate the bulk-diffusion process in the time domain. Chemical diffusivity can be extracted much more reliably with this improved implementation of the GITT method.

25 ENERGY STORAGE↗
DOE OSTI2021

Alpha Shape Analysis (ASA) Framework for Post- Clustering Property Determination in Atom Probe Tomographic Data

While application of clustering algorithms to atom probe tomography data have enabled quantification of solute clusters in terms of number density, size, and subcomposition there exist other properties (e.g., volume, surface area, and composition) that are better determined by defining an interface between the cluster and the surrounding matrix. The limitation in composition results from an ion selection step where the expected matrix ion types are omitted from the cluster search algorithm to enhance the contrast between the matrix and cluster and to reduce the complexity of the search. Previously, composition determination within solute clusters has utilized a secondary envelopment and erosion step on top of conventional methods such as maximum separation. In this work, we present a novel stochastic method that combines the particle identification fidelity of a conventional clustering algorithm with the analytical flexibility of mesh-based approaches through the generation of alpha shapes for each identified cluster. Furthermore, the corresponding mesh accounts for concave components of the clusters and determines the volume and surface area of the clusters; additionally, the mesh boundary is utilized to update the total composition according to the internal ions.

42 ENGINEERING↗
DOE OSTI2024

Analysis of the Structure of Heavy Ion Irradiated LaFeO 3 Using Grazing Angle X-ray Absorption Spectroscopy

Crystalline ceramics are candidate materials for the immobilization of radionuclides, particularly transuranics (such as U, Pu, and Am), arising from the nuclear fuel cycle. Due to the α-decay of transuranics and the associated recoil of the parent nucleus, crystalline materials may eventually be rendered amorphous through changes to the crystal lattice caused by these recoil events. Previous work has shown irradiation of titanate-based ceramics to change the local cation environment significantly, particularly in the case of Ti which was shown to change from 6- to 5-fold coordination. Here, this work expands the Ti-based study to investigate the behavior in Fe-based materials, using LaFeO 3 as an example material. Irradiation was simulated by heavy ion implantation of the bulk LaFeO 3 ceramic, with the resulting amorphous layer characterized with grazing angle X-ray absorption spectroscopy (GA-XAS). Insights into the Fe speciation changes exhibited by the amorphized surface layer were provided through quantitative analysis, including pre-edge analysis, and modeling of the extended X-ray absorption fine structure (EXAFS), of the GA-XAS data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Rheology of concentrated fiber suspensions with a load-dependent friction coefficient

Here we investigate the effects of fiber aspect ratio, roughness, flexibility, and volume fraction on the rheology of concentrated suspensions in a steady shear flow using direct numerical simulations. We model the fibers as inextensible continuous flexible slender bodies with the Euler-Bernoulli beam equation governing their dynamics suspended in an incompressible Newtonian fluid. The fiber dynamics and fluid flow coupling is achieved using the immersed boundary method. In addition, the fiber surface roughness might lead to interfiber contacts, resulting in normal and tangential forces between the fibers, which follow Coulomb’s law of friction. The surface roughness is modeled as hemispherical protrusions on the fiber surfaces. Their deformation results in a normal load-dependent friction coefficient. Our simulations accurately predict the experimentally observed shear thinning in fiber suspensions. Furthermore, we find that the suspension viscosity η increases with increasing the volume fraction, roughness, fiber rigidity, and aspect ratio. The increase in η is the macroscopic manifestation of a similar increase in the microscopic contact contribution to the total stress with these parameters. In addition, we observe positive and negative first N 1 and second N 2 normal stress differences, respectively, with |N 2 | < |N 1 |, in agreement with previous experiments. Last, we propose a modified Maron-Pierce law to quantify the reduction in the jamming volume fraction by increasing the fiber aspect ratio and roughness. Our results and analysis establish the use of fiber surface tribology to tune the suspension flow behavior.

42 ENGINEERING↗
DOE OSTI2022

Effect of applied potential on metal surfaces: Surface energy, Wulff shape and charge distribution

Here we use grand canonical density functional theory to predict the surface energies, Wulff shapes, charge distributions and catalytically active sites of different metal surfaces under electrochemical conditions. We propose a method for computing surface energies from grand canonical density functional theory (GC-DFT) calculations of periodic slab models and use it to compute the surface energies of the facets of Pt, Cu, and Ag crystals to predict their Wulff shapes under electrochemical conditions. GC-DFT predicts that, for the pure metals studied, solvation only slightly affects the Wulff shape while applied potentials considerably affect the surface energies and corresponding Wulff shapes. We used Bader charge analysis of GC-DFT computed electron densities to investigate the effect of applied potential on the distribution of electron density over the atoms of the surfaces of Pt, Cu, Ag, and the 75–25 Ag-Pt and Au-Ni alloys. This analysis shows that, under an applied potential, the electron density is unevenly distributed over the surface atoms and that the charges of atoms more exposed to solvent are more sensitive to bias. Our results show that the most sensitive atom to bias can be used to identify the most favorable adsorption site and thus, the active sites of electrochemical reactions, which is computationally less demanding than calculating the adsorption energies on all possible adsorption sites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Water chemistry in flume channel and hyporheic zone (i.e., porewater) associated with: “Rethinking Aerobic Respiration in the Hyporheic Zone Under Variation in Carbon and Nitrogen Stoichiometry”

Dissolved oxygen (DO), total organic carbon (TOC), total nitrogen (TN), molecular data for organic matter, and biochemical reactions for surface water and porewater (i.e., hyporheic zone) collected from a water recirculating flume located at the University of Texas, Austin. The flume contained real river water from Lower Colorado River(Austin, TX) and clean sand. Hyporheic exchange in the flume was induced through The study aims to understand relationships between aerobic metabolism of organic matter and molecular characteristics of organic matter, such as thermodynamic signature and nitrogen content, through the extent of the hyporheic zone at 10 cm- resolution, and through time. During the experiment, organic matter (dry leaves) was added to the flume and removed after 24 hours. The water samples were collected before the addition of leaves, at the time of removal of leaves, and at hour 72. The water samples were analyzed using ultrahigh resolution Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) and total organic carbon (TOC) and total nitrogen (TN) analysis. Dissolved oxygen content throughout the surface water and the hyporheic zone of the flume was measured with a large planar optode. This data package is associated with the publication ’ Rethinking Aerobic Respiration in the Hyporheic Zone Under Variation in Carbon and Nitrogen Stoichiometry’ published in Environmental Science and Technology (Turețcaia et al., 2023 https://doi.org/10.1021/acs.est.3c04765). The dataset is comprised of five folders (1) Diss_O2_pic, (2) input_files (3) output_files; (4) python_code; and (5) R_code . Diss_O2_pic contains siximages of dissolved oxygen distribution in a bedform at hours 0, 24, and 72 of the experiment conducted in a large recirculation flume. Images are in separate R and G channels (i.e., RGB). The input_files contains (1) a csv file with FTICR peaks identified within each sample, (2) a csv file with molecular information pertinent to FTICR data with Gibbs free energy calculations adjusted for environmental temperature, (3) a csv file containing concentrations of non-purgeable organic carbon measured throughout the experiment , (4) a csv file containing concentrations of total nitrogen measured throughout the experiment, (5) a csv file containing total biochemical reactions (i.e., transformations) identified in the dataset, (6) a csv containing transformation profiles, and (7) a csv file containing transformations with formulas, and (8) a jpg file with schematic representation of locations for sample collection. The output_files contains (1) and xlsx file containing percent biochemical reactions containing nitrogen identified across all 39 sample, (2) a csv file of merged FTICR data and molecular information files, (3) a csv files containing average Gibbs free energy within sampling domains and at each sampling location, (4) a csv file with average concentrations of dissolved oxygen across sampling locations at hour 0, (5) a csv file with average concentrations of dissolved oxygen across sampling locations at hour 24, (6) a csv file with average concentrations of dissolved oxygen across sampling locations at hour 72, (7) a csv file with percent chemical classes identified across sampling locations at hour 0, (8) a csv file with percent chemical classes identified across sampling locations at hour 24, (9) a csv file with percent chemical classes identified across sampling locations at hour 72, and (10) a csv file containing percent nitrogen containing biochemical reactions identified across sampling locations at hours 0, 24, and 72. The python_code contains seven ipynb files which are Jupyter Notebooks used for data analysis and figures generation. The R_code contains 3 R files with R code used for data analysis and figures generation. This data package contains the processed data used in the associated manuscript. This data has not been previously published.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Crystal growth and quantum oscillations in the topological chiral semimetal CoSi

Here, we survey the electrical transport properties of single-crystalline, topological chiral semimetal CoSi grown via different methods. High-quality CoSi single crystals were found in the growth from a tellurium solution. The sample's high carrier mobility enables us to observe quantum oscillations (QOs) in its thermoelectrical signals. Our analysis of QOs reveals two spherical Fermi surfaces around the R point in its Brillouin zone corner. The extracted Berry phases of these electron orbits are consistent with the -2 chiral charge as reported in density functional theory (DFT) calculations. A detailed analysis of the QOs reveals that the spin-orbit-coupling-induced band splitting is less than 2 meV near the Fermi level, one order of magnitude smaller than our DFT calculation. We also report a large phonon-drag-induced Nernst effect in CoSi at intermediate temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Energetics of surface melt in West Antarctica

We use reanalysis data and satellite remote sensing of cloud properties to examine how meteorological conditions alter the surface energy balance to cause surface melt that is detectable in satellite passive microwave imagery over West Antarctica. This analysis can detect each of the three primary mechanisms for inducing surface melt at a specific location: thermal blanketing involving sensible heat flux and/or longwave heating by optically thick cloud cover, all-wave radiative enhancement by optically thin cloud cover, and föhn winds. We examine case studies over Pine Island and Thwaites glaciers, which are of interest for ice shelf and ice sheet stability, and over Siple Dome, which is more readily accessible for field work. During January 2015 over Siple Dome we identified a melt event whose origin is an all-wave radiative enhancement by optically thin clouds. During December 2011 over Pine Island and Thwaites glaciers, we identified a melt event caused mainly by thermal blanketing from optically thick clouds. Over Siple Dome, those same 2011 synoptic conditions yielded a thermal-blanketing-driven melt event that was initiated by an impulse of sensible heat flux and then prolonged by cloud longwave heating. The December 2011 synoptic conditions also generated föhn winds at a location on the Ross Ice Shelf adjacent to the Transantarctic Mountains, and we analyze this case with additional support from automatic weather station data. In contrast, a late-summer thermal blanketing period over Pine Island and Thwaites glaciers during February 2013 showed surface melt initiated by cloud longwave heating and then prolonged by enhanced sensible heat flux. One limitation thus far with this type of analysis involves uncertainties in the cloud optical properties. Nevertheless, with improvements this type of analysis can enable quantitative prediction of atmospheric stress on the vulnerable Antarctic ice shelves in a steadily warming climate.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Earth as a Proxy Exoplanet: Deconstructing and Reconstructing Spectrophotometric Light Curves

Point-source spectrophotometric (single-point) light curves of Earth-like planets contain a surprising amount of information about the spatial features of those worlds. Spatially resolving these light curves is important for assessing time-varying surface features and the existence of an atmosphere, which in turn is critical to life on Earth and significant for determining habitability on exoplanets. Given that Earth is the only celestial body confirmed to harbor life, treating it as a proxy exoplanet by analyzing time-resolved spectral images provides a benchmark in the search for habitable exoplanets. The Earth Polychromatic Imaging Camera (EPIC) on the Deep Space Climate Observatory (DSCOVR) provides such an opportunity, with observations of ∼5000 full-disk sunlit Earth images each year at 10 wavelengths with high temporal frequency. We disk-integrate these spectral images to create single-point light curves and decompose them into principal components (PCs). Using machine-learning techniques to relate the PCs to six preselected spatial features, we find that the first and fourth PCs of the single-point light curves, contributing ∼83.23% of the light-curve variability, contain information about low and high clouds, respectively. Surface information relevant to the contrast between land and ocean reflectance is contained in the second PC, while individual land subtypes are not easily distinguishable (<0.1% total light-curve variation). We build an Earth model by systematically altering the spatial features to derive causal relationships to the PCs. This model can serve as a baseline for analyzing Earth-like exoplanets and guide wavelength selection and sampling strategies for future observations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Turbulence and Cloudiness in Cumulus-Topped Marine Boundary Layers

Turbulence and cloudiness in cumulus-topped marine boundary layers are studied using data from the Atmospheric Radiation Measurement (ARM) Eastern North Atlantic (ENA) site. The analysis includes eight periods of nonprecipitating shallow cumulus clouds, spanning 141 h and encompassing 603 individual clouds. On average, the cumulus had bases at 558 m, were 99 m thick, had a chord length of 500 m, and exhibited an hourly base-layer cloudiness of 12%. Changes in cloud fraction were primarily driven by variations in cloud number not chord length. High-resolution Doppler lidar and cloud radar observations were used to estimate updraft and downdraft mass fluxes in the cumulus base layer under both clear and cloudy regions. Cloudy updrafts contributed only ∼23% of the total updraft mass flux at cloud base, indicating that most upward mass flux originated from clear-air eddies. Updraft strength, rather than updraft fraction, was found to predominantly control both clear and cloudy updraft mass fluxes. Cloud-base cloudiness strongly correlated with cloudy updraft mass flux but showed negligible correlation with clear-air updraft mass flux. Clear-air downdraft mass flux exhibited a strong relationship with the ratio of surface buoyancy to inversion strength. Mesoscale analysis revealed that moist patches had greater cloudiness, updraft mass flux, and vertical velocity variance compared to dry patches. Additionally, mesoscale base-layer cloud fraction was highly and significantly correlated with cloudy updraft mass flux in both dry and moist environments. Results presented herein have implications for cumulus parameterization development along with climatological and model evaluation studies conducted at the ENA site.

cumulus clouds↗
DOE OSTI2023

Offshore wind energy forecasting sensitivity to sea surface temperature input in the Mid-Atlantic

Abstract. As offshore wind farm development expands, accurate wind resource forecasting over the ocean is needed. One important yet relatively unexplored aspect of offshore wind resource assessment is the role of sea surface temperature (SST). Models are generally forced with reanalysis data sets, which employ daily SST products. Compared with observations, significant variations in SSTs that occur on finer timescales are often not captured. Consequently, shorter-lived events such as sea breezes and low-level jets (among others), which are influenced by SSTs, may not be correctly represented in model results. The use of hourly SST products may improve the forecasting of these events. In this study, we examine the sensitivity of model output from the Weather Research and Forecasting model (WRF) 4.2.1 to different SST products. We first evaluate three different data sets: the Multiscale Ultrahigh Resolution (MUR25) SST analysis, a daily, 0.25∘ × 0.25∘ resolution product; the Operational Sea Surface Temperature and Ice Analysis (OSTIA), a daily, 0.054∘ × 0.054∘ resolution product; and SSTs from the Geostationary Operational Environmental Satellite 16 (GOES-16), an hourly, 0.02∘ × 0.02∘ resolution product. GOES-16 is not processed at the same level as OSTIA and MUR25; therefore, the product requires gap-filling using an interpolation method to create a complete map with no missing data points. OSTIA and GOES-16 SSTs validate markedly better against buoy observations than MUR25, so these two products are selected for use with model simulations, while MUR25 is at this point removed from consideration. We run the model for June and July of 2020 and find that for this time period, in the Mid-Atlantic, although OSTIA SSTs overall validate better against in situ observations taken via a buoy array in the area, the two products result in comparable hub-height (140 m) wind characterization performance on monthly timescales. Additionally, during hours-long flagged events (< 30 h each) that show statistically significant wind speed deviations between the two simulations, both simulations once again demonstrate similar validation performance (differences in bias, earth mover's distance, correlation, and root mean square error on the order of 10−1 or less), with GOES-16 winds validating nominally better than OSTIA winds. With a more refined GOES-16 product, which has been not only gap-filled but also assimilated with in situ SST measurements in the region, it is likely that hub-height winds characterized by GOES-16-informed simulations would definitively validate better than those informed by OSTIA SSTs.

17 WIND ENERGY↗
DOE OSTI2018

Verrucomicrobia are prevalent in north-temperate freshwater lakes and display class-level preferences between lake habitats

The bacterial phylum Verrucomicrobia was formally described two decades ago and originally believed to be a minor member of many ecosystems; however, it is now recognized as ubiquitous and abundant in both soil and aquatic systems. Nevertheless, knowledge of the drivers of its relative abundance and within-phylum habitat preferences remains sparse, especially in lake systems. Here, we documented the distribution of Verrucomicrobia in 12 inland lakes in Southeastern Michigan, a Laurentian Great Lake (Lake Michigan), and a freshwater estuary, which span a gradient in lake sizes, depths, residence times, and trophic states. A wide range of physical and geochemical parameters was covered by sampling seasonally from the surface and bottom of each lake, and by separating samples into particle-associated and free-living fractions. On average, Verrucomicrobia was the 4 th most abundant phylum (range 1.7–41.7%). Fraction, season, station, and depth explained up to 70% of the variance in Verrucomicrobia community composition and preference for these habitats was phylogenetically conserved at the class-level. When relative abundance was linearly modeled against environmental data, Verrucomicrobia and non-Verrucomicrobia bacterial community composition correlated to similar quantitative environmental parameters, although there were lake system-dependent differences and > 55% of the variance remained unexplained. A majority of the phylum exhibited preference for the particle-associated fraction and two classes (Opitutae and Verrucomicrobiae) were identified to be more abundant during the spring season. This study highlights the high relative abundance of Verrucomicrobia in north temperate lake systems and expands insights into drivers of within-phylum habitat preferences of the Verrucomicrobia.

54 ENVIRONMENTAL SCIENCES↗