Search NASA⌕ Search

SEARCH · Search NASA

Results for “technology diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Neutronics and thermal-hydraulics simulation of generic pebble-bed fluoride-salt-cooled high-temperature reactor (gFHR)

The fluoride-salt-cooled high-temperature reactor (FHR) is one type of the advanced reactors and has been attracting great interest from the research institutes and commercial companies in the recent years. However, currently the technology is relatively immature. To facilitate the design and safety analysis of FHRs, Kairos Power published the generic FHR (gFHR) benchmark. In this paper, a hybrid method combining the stochastic code and deterministic code is developed to simulate the gFHR benchmark. Serpent 2 is employed as a few-group cross section generator and the cross sections are applied to the finite difference neutron diffusion code AGREE. A good consistency with the gFHR benchmark is achieved. The agreement between the Serpent 2 results and the AGREE results shows that the hybrid method is applicable to FHRs. The thermal-hydraulics are coupled to neutronics for the steady-state calculations and good agreement between AGREE and SAM is achieved. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1990

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 6: Aerospace knowledge diffusion in the academic community: A report of phase 3 activities of the NASA/DOD Aerospace Knowledge Diffusion Research Project

Descriptive and analytical data regarding the flow of aerospace-based scientific and technical information (STI) in the academic community are presented. An overview is provided of the Federal Aerospace Knowledge Diffusion Research Project, illustrating a five-year program on aerospace knowledge diffusion. Preliminary results are presented of the project's research concerning the information-seeking habits, practices, and attitudes of U.S. aerospace engineering and science students and faculty. The type and amount of education and training in the use of information sources are examined. The use and importance ascribed to various information products by U.S. aerospace faculty and students including computer and other information technology is assessed. An evaluation of NASA technical reports is presented and it is concluded that NASA technical reports are rated high in terms of quality and comprehensiveness, citing Engineering Index and IAA as the most frequently used materials by faculty and students.

Pinelli, Thomas E.↗
DOE OSTI2019

Material world: forecasting household appliance ownership in a growing global economy

This paper presents a methodology for modeling residential appliance uptake as a function of macroeconomic variables, and presents forecasts of appliance diffusion through 2030 for several scenarios of economic (GDP) growth. The approach followed allows the modeler to construct a bottom­-up analysis based at the end use and the household level. It captures the appliance uptake and the saturation effect which will affect the energy demand growth in the residen­tial sector. With this approach, the modeler can also account for stock changes in technology and efficiency as a function of time.

Letschert, Virginie↗
NASA NTRS1978

Industrial ion source technology

An analytical model was developed to describe the development of a coned surface texture with ion bombardment and simultaneous deposition of an impurity. A mathematical model of sputter deposition rate from a beveled target was developed in conjuction with the texturing models to provide an important input to that model. The establishment of a general procedure that will allow the treatment of manay different sputtering configurations is outlined. Calculation of cross sections for energetic binary collisions was extened to Ar, Kr.. and Xe with total cross sections for viscosity and diffusion calculated for the interaction energy range from leV to 1000eV. Physical sputtering and reactive ion etching experiments provided experimental data on the operating limits of a broad beam ion source using CF4 as a working gas to produce reactive species in a sputtering beam. Magnetic clustering effects are observed when Al is seeded with Fe and sputtered with Ar(?) ions. Silicon was textured at a micron scale by using a substrate temperature of 600 C.

Kaufman, H. R.↗
DOE OSTI2022

Heat conduction in an irregular magnetic field. Part 2. Heat transport as a measure of the effective non-integrable volume

Given the large anisotropy of transport processes in magnetized plasmas, the magnetic field structure can strongly impact heat diffusion: magnetic surfaces and cantori form barriers to transport while chaotic layers and island structures can degrade confinement. When a small but non-zero amount of perpendicular diffusion is included, the structure of the magnetic field becomes less important, allowing pressure gradients to be supported across chaotic regions and island chains. We introduce a metric for the effective volume over which the local parallel diffusion dominates based on the solution to the anisotropic heat diffusion equation. To validate this metric, we consider model fields with a single island chain and a strongly chaotic layer for which analytic predictions of the relative parallel and perpendicular transport can be made. We also analyse critically chaotic fields produced from different sets of perturbations, highlighting the impact of the mode number spectrum on the heat transport. Our results indicate that this metric coincides with the effective volume of non-integrability in the limit $\kappa _{\perp } \rightarrow 0$ , where $\kappa_{\perp}$ is the perpendicular diffusion coefficient. We propose that this metric be used to assess the impact of non-integrability on the heat transport in stellarator equilibria.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Modeling turbulent impurity transport in the SOL of DIII-D with a reduced model

A novel impurity transport model that approximates SOL turbulence as a fluctuating poloidal electric field is shown to be an acceptable replacement for the traditional approach of assigning an arbitrary radial diffusion coefficient to the impurity ions. The model is implemented in the DIVIMP impurity transport code and applied to an L-Mode tungsten divertor experiment on DIII-D. The poloidal electric field is represented as fluctuating between ±1000 V m –1 based on previous measurements. The resulting intermittent v r = E θ × B T transport causes ions to transport both into the core as well as into the far-SOL. Simultaneous agreement with estimates of the W density just inside the separatrix as well as in the far-SOL is obtained (n W ~ 10 14 m –3 and n W ~ 10 12 m –3 , respectively). Prompt re-deposition of the W ions was necessary to obtain agreement (f redep ~ 99%). Here, we conclude that simulating impurity transport using a physics-based approximation for turbulence in the SOL, versus arbitrarily assigning diffusion coefficients, may enable better reactor scale predictions of core impurity contamination.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

Structures and diffusion of two-dimensional dusty plasmas on one-dimensional periodic substrates

Using numerical simulations, we examine the structure and diffusion of a two-dimensional dusty plasma (2DDP) in the presence of a one-dimensional periodic substrate (1DPS) as a function of increasing substrate strength. Both the pair correlation function perpendicular to the substrate modulation and the mean-squared displacement (MSD) of dust particles are calculated. It is found that both the structure and dynamics of 2DDP exhibit strong anisotropic effects, due to the applied 1DPS. As the substrate strength increases from zero, the structure order of dusty plasma along each potential well of 1DPS increases first probably due to the competition between the interparticle interactions and the particle-substrate interactions, and then decreases gradually, which may be due to the reduced dimensionality and the enhanced fluctuations. The obtained MSD along potential wells of 1DPS clearly shows three processes of diffusion in our studied 2DDP. Finally, between the initial ballistic and finally diffusive motion, there is the intermediate subdiffusion discovered here, which may result from the substrate-induced distortion of the caging dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Advanced supercritical carbon dioxide cycles

The supercritical carbon dioxide cycle (sCO2) has been chosen as the most promising cycle to meet the SunShot goals with a power block that has the potential to achieve thermal efficiencies of 50+% with a turbine inlet temperature of 720 o C. While this cycle has significant potential, it is a fairly new cycle and therefore the costs and performance of the cycle are not known to the level required for detailed economic analysis. There are also multiple cycle configurations that may be used and the choice of configuration could depend on size, cost constraints, efficiency, cooling mode, O&M costs, etc. Each of the variants has particular advantages and drawbacks that have to be understood. The most cost effective way to understand these variants is to use models that allow us to predict the performance of the cycles linked to the heat source (solar thermal energy). In order to do this these models, need to be developed and improved to better predict the costs and performance of the cycle. One of the issues identified with the supercritical Brayton cycle is the fact that a large amount of internal heat exchange is required in order for it to realize its efficiency potential. To address this, recuperators of the Printed Circuit Heat Exchanger (PCHE) design have been primarily considered. While PCHEs are fairly advanced technology and have significant potential there are several drawbacks associated with them. The first being their cost; it is estimated that the two recuperators in a recompression Brayton cycle will cost more than 30% of the entire power block. Another major issue is the in service performance and lack of ability to repair or easily clean the recuperators. If there is a defect in a diffusion bond, fouling or plugging of the channels or mechanical damage due to rapid thermal transient then the entire PCHE may need to be replaced. The third issue is the lack of data and information on the performance of PCHEs at the scale that would be required even for a small 10 MWe plant. To date PCHE heat exchangers have not been constructed at this size and it is necessary to have multiple modules headered together in order to be able to recuperate up to the 40 MWth required in even a small, 10 MWe plant.

14 SOLAR ENERGY↗
DOE OSTI2020

A First Investigation of Agriculture Sector Perspectives on the Opportunities and Barriers for Agrivoltaics

Agrivoltaic systems are a strategic and innovative approach to combine solar photovoltaic (PV)-based renewable energy generation with agricultural production. Recognizing the fundamental importance of farmer adoption in the successful diffusion of the agrivoltaic innovation, this study investigates agriculture sector experts’ perceptions on the opportunities and barriers to dual land-use systems. Using in-depth, semistructured interviews, this study conducts a first study to identify challenges to farmer adoption of agrivoltaics and address them by responding to societal concerns. Results indicate that participants see potential benefits for themselves in combined solar and agriculture technology. The identified barriers to adoption of agrivoltaics, however, include: (i) desired certainty of long-term land productivity, (ii) market potential, (iii) just compensation and (iv) a need for predesigned system flexibility to accommodate different scales, types of operations, and changing farming practices. The identified concerns in this study can be used to refine the technology to increase adoption among farmers and to translate the potential of agrivoltaics to address the competition for land between solar PV and agriculture into changes in solar siting, farming practice, and land-use decision-making.

14 SOLAR ENERGY↗
NASA NTRS1975

Current status of silicon solar cell technology

Recent advances in solar cell technology have led to the development of laboratory cells with efficiencies above 15% and production cells with efficiencies in the area of 13%. The increased output is largely the result of increases in the short-circuit current. The most significant gain in the amount of light entering the cell has been obtained through surface texturing by chemical etching techniques. Sheet resistances resulting from phosphorus diffusion in the 800 C temperature range yield junction depths on the order of 0.1 micrometer, leading to significant increases in the blue region of the cell spectral response. The inclusion of a back surface field in 10 ohm-cm cells has produced an increase in open-circuit voltage of about 50 mV and an increase in the minority carrier lifetime. It appears that a low emitter efficiency of the diffused region is the cause of poor voltages. Future research will be primarily directed toward correcting this deficiency and toward the development of low cost production methods.

Brandhorst, H. W., Jr.↗
NASA NTRS2008

Vibroacoustic Response of the NASA ACTS Spacecraft Antenna to Launch Acoustic Excitation

The Advanced Communications Technology Satellite was an experimental NASA satellite launched from the Space Shuttle Discovery. As part of the ground test program, the satellite s large, parabolic reflector antennas were exposed to a reverberant acoustic loading to simulate the launch acoustics in the Shuttle payload bay. This paper describes the modelling and analysis of the dynamic response of these large, composite spacecraft antenna structure subjected to a diffuse acoustic field excitation. Due to the broad frequency range of the excitation, different models were created to make predictions in the various frequency regimes of interest: a statistical energy analysis (SEA) model to capture the high frequency response and a hybrid finite element-statistical energy (hybrid FE-SEA) model for the low to mid-frequency responses. The strengths and limitations of each of the analytical techniques are discussed. The predictions are then compared to the measured acoustic test data and to a boundary element (BEM) model to evaluate the performance of the hybrid techniques.

Larko, Jeffrey M.↗
NASA NTRS2010

Solar Radiation Transport in the Cloudy Atmosphere: A 3D Perspective on Observations and Climate Impacts

The interplay of sunlight with clouds is a ubiquitous and often pleasant visual experience, but it conjures up major challenges for weather, climate, environmental science and beyond. Those engaged in the characterization of clouds (and the clear air nearby) by remote sensing methods are even more confronted. The problem comes, on the one hand, from the spatial complexity of real clouds and, on the other hand, from the dominance of multiple scattering in the radiation transport. The former ingredient contrasts sharply with the still popular representation of clouds as homogeneous plane-parallel slabs for the purposes of radiative transfer computations. In typical cloud scenes the opposite asymptotic transport regimes of diffusion and ballistic propagation coexist. We survey the three-dimensional (3D) atmospheric radiative transfer literature over the past 50 years and identify three concurrent and intertwining thrusts: first, how to assess the damage (bias) caused by 3D effects in the operational 1D radiative transfer models? Second, how to mitigate this damage? Finally, can we exploit 3D radiative transfer phenomena to innovate observation methods and technologies? We quickly realize that the smallest scale resolved computationally or observationally may be artificial but is nonetheless a key quantity that separates the 3D radiative transfer solutions into two broad and complementary classes: stochastic and deterministic. Both approaches draw on classic and contemporary statistical, mathematical and computational physics.

Davis, Anthony B.↗
NASA NTRS2017

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D

Full seven-equation Reynolds stress turbulence models are promising tools for today’s aerospace technology challenges. This paper examines two such models for computing challenging turbulent flows including shock-wave boundary layer interactions, separation and mixing layers. The Wilcox and the SSG/LRR full second-moment Reynolds stress models have been implemented into the FUN3D (Fully Unstructured Navier-Stokes Three Dimensional) unstructured Navier-Stokes code and were evaluated for four problems: a transonic two-dimensional diffuser, a supersonic axisymmetric compression corner, a compressible planar shear layer, and a subsonic axisymmetric jet. Simulation results are compared with experimental data and results computed using the more commonly used Spalart-Allmaras (SA) one-equation and the Menter Shear Stress Transport (SST-V) two-equation turbulence models.

reynolds averaging↗
NASA NTRSDate not supplied

Use of Diffusion Bonded Cu Strap and Integrated MLI for Thermal Control of 100 K IR Detector on L’Ralph Instrument

Passive cooling of cryogenic instruments is one of the most challenging aspects of spaceflight thermal control systems. They are highly sensitive to parasitic heat leaks from their warmer environment, especially the spacecraft components. The L’Ralph instrument on the Lucy mission is an example of such a system, with its LEISA detector requiring passive cooling to temperatures below 112 K. MLI performance can be measured in terms of estar, and analysts apply bias between a high and low estar value. This approach works well for conventional MLI at room temperature, however, it can be dangerous when a mission goes through a wide range of temperatures during its lifetime, with estar values increasing exponentially as temperatures get colder. Various estar correlations are presented as well as how L’Ralph is approaching the MLI problem with the use of IMLI. IMLI uses discrete spacers to isolate each layer, and doesn’t require intermediate layers such as dacron netting. This results in estar performance that can be more precisely estimated, and yields valuesaround 0.004 at the 112K operating temperature. L’Ralph is using IMLI on the backside of the radiator, which permits a more effective use of increased radiator area, by minimizing the area dependent heat leak impact from the instrument backloading. The detector is thermally coupled to the radiator via a diffusion bonded Cu strap. The diffusion bonding process chemically bonds the Cu foil ends in order to maximize heat transfer effectiveness across the multiple foils used. Employing a pressure compensation design via the use of Ti blocks and a clamp at the strap ends ensures that as temperatures go colder, pre-load is maintained in order to minimize resistance at the strap ends. The use of both of these technologies, and how they work together are crucial to the success of the L’Ralph thermal control system.

Thermal↗
DOE OSTI2023

Laser heating and evaporation of a single droplet

The laser technology is being abundantly studied for controlled energy deposition for a range of applications in aerodynamic flow control, material processing, ignition, and combustion. The absorption of laser radiation by liquid droplets affects further propagation of laser in the atmosphere and causes bleaching of suspended droplets while the ignition and combustion characteristics in combustors are influenced by the evaporation rate of the sprayed fuel. In this work, we present a multi-dimensional mathematical model built on OpenFOAM for laser heating and evaporation of a single droplet in the diffusion dominated regime taking into account absorption of the laser radiation, evaporation process and vapor flow dynamics. The developed solver is validated against available experimental and numerical data for the ethanol and water droplet heating and evaporation. For continuous heating the peak temperature is established by the balance of cooling, evaporation and heating and results in high temperature for larger droplets. It has been shown that for heating by a single laser pulse the maximum temperature of droplets depends only on the peak intensity of the laser radiation. Furthermore, for the peak irradiance close to the transition to the boiling regime, temporal dynamics of the droplet temperature is independent of the droplet size. With proper normalization of time, the dynamics of the droplet shrinkage and cooling is shown to be independent of droplet sizes and peak laser intensities. The influence of cooling and evaporation processes on droplet heating was found to be controlled by the pulse repetition rate for repeated pulse operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

SA508 low alloy steel to 316L stainless steel dissimilar metal joint made by powder metallurgy hot isostatic pressing

Joining ferritic SA508 low alloy steel (LAS) and austenitic 316 L stainless steel (SS) via powder metallurgy hot isostatic pressing (PM-HIP) was evaluated as an alternative method to welding. This study investigated the mechanical and microstructural evolutions of the bimetallic interface under different joint designs and heat treatments. Here, the direct joining of dissimilar metal alloys by PM-HIP method resulted in two designs: 1) powder SA508 to solid bar 316 L (P508–B316L) and 2) powder 316 L solid bar SA508 (P316L-B508). In both cases, P508–B316L and P316L-demonstrated satisfactory tensile strength, however, high hardness and severe depreciation in toughness were located on the bimetallic interface. The mechanisms responsible for the detrimental mechanical properties were verified. Large oxides were observed in P508–B316L due to the prior powder boundary (PPB) oxides present in SA508 powder. The intense sensitization occurred from the formation of M 23 C 6 carbides, consequently from the slow cooling after PM-HIP in P316L-B508. Post-HIP heat treatments were explored to reduce the distance of carbide formation; however, the heat treatment could not eliminate the carbides. The experimental results were compared to the diffusion couple simulation as a function of carbide formation with distance. The analysis also showed the high hardness at the bimetallic interface was primarily contributed by solid solution strengthening. In conclusion, the direct joining of P316L-B508 and P508–B316L via PM-HIP was deemed to be unfeasible, and a transitional material is necessary to impede the diffusion of carbon.

316L stainless Steel↗
DOE OSTI2018

Analytical estimates of proton acceleration in laser-produced turbulent plasmas

With the advent of high power lasers, new opportunities have opened up for simulating astrophysical processes in the laboratory. We show that second-order Fermi acceleration can be directly investigated at the National Ignition Facility, Livermore. This requires measuring the momentum-space diffusion of 3 MeV protons produced within a turbulent plasma generated by a laser. In conclusion, treating Fermi acceleration as a biased diffusion process, we show analytically that a measurable broadening of the initial proton distribution is then expected for particles exiting the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Solid-State Side-Chain Functionalization of Conjugated Polymers for Expanded Chemical and Functional Versatility

Conjugated polymers that integrate diverse chemical functionalities with high electronic performance are essential for advanced organic electronic, optoelectronic, and biointerfaced technologies. Achieving such multifunctionality typically requires grafting functional units onto polymer side chains. However, conventional solution-phase approaches remain constrained by solubility limitations, side-chain-induced packing disruptions, and challenges in preserving charge transport. Here, we introduce a solid-state side-chain functionalization strategy that exploits a swellable polar side-chain architecture and azide–alkyne click chemistry to enable efficient molecular diffusion and reaction throughout predeposited polymer thin films. This approach substantially broadens the chemical compatibility of graftable units and mitigates the adverse effects on the electrical property. Moreover, the method supports spatially selective functionalization within a continuous film, enabling the patterned incorporation of chemically distinct groups to produce spatially defined optical properties. Here, this solid-state strategy thus provides a versatile platform for constructing conjugated polymers with expanded chemical versatility, preserved electronic performance, and programmable spatial functionality.

Conjugated polymers↗