Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Behavior under LOCA conditions on enhanced accident tolerant chromium coated zircaloy-4 claddings

For enhanced accident tolerant fuels for light water reactors application, chromium coatings on zirconium based nuclear fuel claddings are developed and studied at CEA in the framework of the French CEA-EDF-AREVA collaborative program. The results obtained so far, mainly on Zircaloy-4 substrate, show very good corrosion resistance in nominal conditions and significant enhancement of the resistance of the material to oxidation in steam at high temperature (HT), up to 1300 Celsius degrees, with a drastic decrease of hydrogen release and/or pick-up. The present paper reports some new results obtained on chromium coated Zircaloy-4 claddings tested in loss-of-coolant accident (LOCA) conditions. In order to investigate the potential effect of the coating on the cladding mechanical behavior at HT and the capacity of the coating to sustain significant substrate deformation (i.e., during ballooning until burst occurrence) without generalized cracking/peeling, a preliminary limited set of internal pressure creep and temperature ramp tests have been performed in steam environment thanks to the EDGAR facility. The thermal-mechanical tests were done for testing/burst temperatures ranging from 600 C. degrees (α{sub Zr} phase domain) up to 1000 C. degrees (β{sub Zr} phase domain) on 50 cm long low-tin Zircaloy-4 cladding samples with a 15 μm thick outer chromium coating. It is shown that: -) whatever the applied temperature/pressure values, the chromium coating is still fully adherent after having experienced ballooning and burst, including at the vicinity of the burst opening where the Zircaloy-4 clad substrate is highly deformed; -) a HT strengthening effect of the coating on the overall creep clad behavior is evidenced when compared to uncoated Zircaloy-4 cladding materials tested in the same conditions; -) as a consequence, it is observed that, in the 600-750 C. degrees temperature range (α{sub Zr} phase domain) and after burst occurrence, the balloon sizes (i.e., 'uniform' and maximum hoop strains) are generally reduced when compared to uncoated materials; -) regarding the burst mechanism in the β{sub Zr} phase temperature range (1000 C. degrees), it is interesting to observe that, even if some ballooning occurred prior to the cladding failure, the actual burst openings are generally very small (in the order of 1 mm{sub 2} or less), reducing the risk of fuel fragments dispersal in the coolant.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In-Pile testing of CrN, TiAIN, and AlCrN coatings on Zircaloy cladding in the Halden reactor - 2016-0011

CrN coating came out as superior and remained completely intact after the irradiation, as evidenced by SEM analysis. Based on these promising results, an in-pile experiment with coated Zircaloy claddings (containing fuel) was performed in the Halden reactor in PWR conditions in 2014. The experimental rig contained four Zircaloy-4-clad fuel rods-three coated (CrN, TiAlN, and AlCrN) and one uncoated. Due to a mechanical deformation of tubes for cooling water within the rig, the fuel rods were insufficiently cooled, resulting in a higher-than-normal cladding temperature. Nevertheless, an SEM examination showed that the CrN coating largely remained intact apart from several local spots where the coating had cracked or disappeared. Underneath the cracked coating, oxide formation was observed in the Zircaloy-4 cladding. The TiAlN and AlCrN coatings both disappeared after the irradiation. (authors)

36 MATERIALS SCIENCE↗

Characterization of Thin Films and Coatings

Just as the numbers and types of thin films have grown dramatically, the needs and approaches for their characterization have also expanded significantly. Adequate characterization of a film or coating depends on the process to create the coating as well as the planned or potential application(s) and expected lifetime. Characterization of a coating or film necessarily requires application of methods that determine properties of the coating and not primarily the substrate. This places some focus on methods that determine properties of layers and not "bulk" material. However, the increasing importance of micro- and nano-structures in coatings and films places an increased importance in methods with high spatial resolution. The growing use of organic films and coatings and the importance of molecular functionalization of inorganic surfaces increase the importance for different types of molecular characterization tools. In most circumstances appropriate characterization requires use of a combination of tools. The purpose of this chapter is to provide an introduction to the basic methods and overview applications for some of the most important tools for characterization of films, coatings and surfaces. The chapter will be organized in six sections: • Technique Overview – This section provides a high level summary of the types of information that can be obtained by different methods and includes information about their sensitivity and resolution. • Incident Photon Methods – Techniques involving incident photons are described and some brief examples of application are shown. Methods included are: x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), x-ray reflectivity (XRR), Fourier transform infra-red spectroscopy (FTIR), laser Raman spectroscopy, ellipsometry, and photoluminescence spectroscopy. • Incident Ion Methods - Methods initiated by ion irradiation are summarized including: Rutherford backscattering spectrometry (RBS), nuclear reaction analysis (NRA), ion channeling, elastic recoil detection analysis (ERDA), secondary ion mass spectrometry (SIMS), glow discharge mass spectrometry and uses of focused ion beams (FIB) (often in combination with scanning electron microscopy). • Incident Electron Methods – Methods involving incident electrons include: Auger electron spectroscopy (AES), scanning electron microscopy (SEM), energy dispersive x-ray analysis (EDS), transmission electron microscopy (TEM), and electron diffraction (low energy electron diffraction [LEED] and reflection high energy electron diffraction [RHEED]). • Other Methods – Additional methods described include scanning probe microscopy (SPM) (including scanning tunneling microscopy [STM] and atomic force microscopy [AFM]) and atom probe microscopy.

36 MATERIALS SCIENCE↗

EXAMINATION OF THE OXIDATION PROTECTION OF ZINC COATINGS FORMED ON COPPER ALLOYS AND STEEL SUBSTRATES

The exposure of metallic components at aggressive high temperature environments, usually limit their usage at similar application because they suffer from severe oxidation attack. Copper alloys are used in a wide range of high-quality indoor and outdoor applications, statue parts, art hardware, high strength and high thermal conductivity applications. On the other hand, steel is commonly used as mechanical part of industrial set outs or in the construction sector due to its high mechanical properties. The aim of the present work is the examination of the oxidation resistance of pack cementation zinc coatings deposited on copper, leaded brass and steel substrates at elevated temperature conditions. Furthermore, an effort made to make a long-term evaluation of the coated samples durability. The oxidation results showed that bare substrates appear to have undergone severe damage comparing with the coated ones. Furthermore, the mass gain of the uncoated samples was higher than this of the zinc covered ones. Particularly zinc coated brass was found to be more resistant to oxidation conditions in which it was exposed as it has the lower mass gain as compared to the bare substrates and zinc coated copper. Zinc coated steel was also proved to be more resistive than the uncoated steel.

36 MATERIALS SCIENCE↗

Ice Nucleation of Bare and Sulfuric Acid-coated Mineral Dust Particles and Implication for Cloud Properties

Ice nucleation properties of different dust species coated with soluble material are not well understood. We determined the ice nucleation ability of bare and sulfuric acid coated mineral dust particles as a function of temperature (-25 to -35 deg C) and relative humidity with respect to water (RHw). Five different mineral dust species: Arizona test dust (ATD), illite, montmorillonite, quartz and kaolinite were dry dispersed and size-selected at 150 nm and exposed to sulfuric acid vapors in the coating apparatus. The condensed sulfuric acid soluble mass fraction per particle was estimated from the cloud condensation nuclei activated fraction measurements. The fraction of dust particles nucleating ice at various temperatures and RHw was determined using a compact ice chamber. In water-subsaturated conditions, compared to bare dust particles, we found that only coated ATD particles showed suppression of ice nucleation ability while other four dust species did not showed the effect of coating on the fraction of particles nucleating ice. The results suggest that interactions between the dust surface and sulfuric acid vapor are important, such that interactions may or may not modify the surface via chemical reactions with sulfuric acid. At water-supersaturated conditions we did not observed the effect of coating, i.e. the bare and coated dust particles had similar ice nucleation behavior.

Kulkarni, Gourihar R.↗

Design, Fabrication, and Screening of Environmental‐Thermal Barrier Coatings Prepared by Ultrafast High‐Temperature Sintering

Abstract The demand for more efficient gas turbines relies heavily on the development of new environmental‐thermal barrier coatings (ETBCs). However, there is still uncertainty about which alloys and composites will be used for the next generation of turbine blades, as well as the most promising coating materials. Herein, an ETBCs development strategy is presented by integrating the coating design, synthesis, and screening using an ultrafast high temperature sintering (UHS) technique to accelerate coating improvements. The initial basis for composition selection is their thermal expansion mismatch with the substrate alloys; for which a temperature‐dependent coefficient of thermal expansion database is created. By combining tape casting method with the UHS technique a high‐throughput synthesis of single and multi‐layer coatings are realized with different compositions, layer stacking sequences, and layer thicknesses. To evaluate the coatings, thermal cycling tests from room temperature to 1300 °C are conducted. The approach enabled coatings on objects with complex geometries, multi‐layer ETBCs, and porosity tailoring by using staged UHS that runs with different temperatures and durations. The fast iteration strategy is more cost‐effective for the screening of ETBCs compared to conventional methods and greater throughput which can be further extended for rapid optimization of other materials systems.

Xie, Hua↗

Anticorrosive Behavior and Porosity of Tricationic Phosphate and Zirconium Conversion Coating on Galvanized Steel

This work evaluates the corrosion resistance of galvanized steel treated with tricationic phosphate and zirconium conversion coating after painting, by using electrochemical techniques, accelerated and field corrosion tests. A non-uniform and heterogeneous distribution of zirconium on the steel surface was observed due to preferential nucleation of the zirconium on the aluminum-rich sites on the surface of galvanized steel. The long-term anti-corrosion performance in a saline solution was better for the phosphate coating up to 120 days. The coating capacitance registered a higher increase for the zirconium coatings than the phosphate coatings up to 120 days of immersion. This result agrees with the higher porosity of zirconium coating in relation to the phosphate coating. After 3840 h of accelerated corrosion test, and after 1 year of accelerated field test, zirconium-treated samples showed an average scribe delamination length higher than the phosphate-treated samples.

36 MATERIALS SCIENCE↗

Parametric Analysis and Modeling for the Porosity Prediction in Suspension Plasma-Sprayed Coatings

The porous architecture of suspension plasma-sprayed coatings has a significant influence on the coating performances and thus should be properly designed for the intended applications. In this study, YSZ coatings were manufactured by suspension plasma spray (SPS), and a parametric study was performed with five different process parameters: suspension mass load, original powder particle size, substrate surface topology, spray distance, and spray step. Afterward, the porosity of the as-prepared coatings was investigated by imaging and x-ray transmission technique. A multivariate analysis on the collected experimental data was carried out. We report the results indicated that: (1) The total porosity of SPS coatings increases with the decrease in suspension mass load, while it shows the opposite trend by decreasing the spray distance, original powder particle size, substrate roughness, and spray step; (2) The main factor affecting coating total porosity is spray distance. Finally, a predictive model for coating total porosity was developed and was verified by experiments. Control of total porosity by using the predictive model was presented and explained as well.

47 OTHER INSTRUMENTATION↗

Effects of Plume Targeted Cooling on Residual Stress in Controlled Atmosphere Plasma Sprayed Coatings

Thermal spray processes can benefit from cooling to maintain substrate temper, reduce processing times, and manage thermally induced residual stresses. “Plume quenching” is a plume-targeted cooling technique which has been shown to reduce substrate temperatures by redirection of hot plume gases using a lateral argon curtain injected into the plume, while limiting interaction with the substrate or affecting coating properties. Here, this study explores the use of this technique for residual stress management by reducing the thermally driven component in nickel and tantalum coatings on titanium and aluminum substrates. The in-situ residual stress profiles were measured for all substrate and coating pairings during spraying and cooling, and the deposition and thermal stresses recorded. For substrate and coating pairings where the predominant component of residual stress was thermal (driven by a large difference in coefficient of thermal expansion, Δα, between coating and substrate), plume quenching reduced both the thermal stress and the final stress state of the coating. This was seen primarily in tantalum on aluminum coatings where the Δα was -17 × 10 -6 /°C, and thermal stress was reduced by 7.5% and 22.4% for the plume quenching rates of 50 and 100 slpm, respectively.

42 ENGINEERING↗

Quantifying dislocation density in Al-Cu coatings produced by cold spray deposition

This work quantifies the plastic deformation in terms of dislocation density for a series of cold sprayed Al-Cu coatings with copper contents from 2 mass% to 5 mass%. The success of the deposition and consolidation of the feedstock powders during the cold spray process rely on the occurrence of significant plastic deformation. Inert gas atomized Al-Cu alloy powders were sprayed onto substrates made of an Al-Cu-Mg-Mn alloy (AA2024) to produce dense coatings using a low pressure cold spray system with helium as the carrier gas. X-ray diffraction patterns were obtained from the Al-Cu feedstock powder material and the cold sprayed coatings using a monochromatic X-ray source, and the dislocation density was determined via an X-ray whole profile analysis. Increasing the Cu alloy content (from 2 mass% to 5 mass%) systematically increased the dislocation density in the Al-Cu coatings from (4.3 ± 0.5) × 10 14 m -2 to (7.5 ± 0.8) × 10 14 m -2 . The dislocation densities in the feedstock powders ranging from (0.4 ± 0.1) × 10 14 m -2 to (1.8 ± 0.2) × 10 14 m -2 were all lower than the dislocation densities in the corresponding coatings. The increasing deformation level in the Al-Cu coatings with Cu additions were confirmed by the classic and modified Williamson-Hall analyses of X-ray diffraction data, and peak breadth measurements from neutron diffraction data. Finally, a high density of dislocations was also observed in these coatings via electron backscatter diffraction and transmission electron microscopy.

36 MATERIALS SCIENCE↗

Comprehensive evaluation of commercially scalable atomic-layer-deposited alumina coating impact on full cell battery performance across varied test conditions

Atomic Layer Deposition (ALD) has emerged as a strategic enhancement method for lithium-ion battery (LIB) materials offering potential benefits and durability benefits for industrial battery production. However, the translation from laboratory achievements to commercial-scale applications has been limited. Here, this study aims to bridge this gap by comprehensively evaluating the effects of commercially scalable Al 2 O 3 ALD coatings using full pouch cell performance as a means to assess the ALD impact. We utilized large-scale slot-die coating techniques to ensure consistent electrode quality and tested four configurations of pouch cells to analyze the individual effects of ALD coating on anode and cathode electroactive materials. Our extensive testing matrix included long-term cycling, fast discharge, fast charge, leakage current, and high voltage tests. While at lower C-rates (<~1C), the influence of Al 2 O 3 coatings on cell performance is not significant. Fast charging conditions reveal that the anode ALD coating significantly enhances performance via a passivating effect, while on the cathode, it is detrimental, potentially due to increased resistance of the thin interfacial layer formed during the ALD processing. Leakage current and high-voltage tests show that the application of ALD coatings on either anode or cathode effectively minimizes side reactions at the electrode-electrolyte interface. Additionally, ALD coatings significantly mitigate concentrated and localized lithium plating on the anodes. These insights provide a valuable understanding of the potential of ALD technologies in LIB manufacturing to tailor cell performance, paving the way for safer, more efficient, and cost-effective battery solutions.

25 ENERGY STORAGE↗

Pb, Cu, and Zn distributions at humic acid-coated metal-oxide surfaces

Here, mineral surfaces are often coated by natural organic matter (NOM), which has a major influence on metal-ion sorption and sequestration because of the abundance of binding sites in such coatings and the changes they cause in local nanoscale environments. The effects of NOM coatings on mineral surfaces are, however, still poorly understood at the molecular level due to the complexity of these systems. In this study, we have applied long-period X-ray standing wave-fluorescence yield (LP-XSW-FY) spectroscopy to measure the partitioning of naturally present Cu(II) (0.0226%), Zn(II) (0.009%), and Pb(II) ( 0.0004%) between Elliott Soil Humic Acid (ESHA) coatings and three model single-crystal metal-oxide substrates: α-Al 2 O 3 (0 0 0 1), α-Al 2 O 3 (1 1 0 2), and α-Fe 2 O 3 (0 0 0 1). The competitive sorption effects among these metal ions for binding sites in the ESHA coatings and on the metal-oxide surfaces were investigated as a function of reaction time, calcium content, and solution pH. Pb(II) ions present in the ESHA coatings were found to redistribute to reactive α-Al 2 O 3 (1 1 0 2) and α-Fe 2 O 3 (0 0 0 1) surfaces after 3 h of reaction (pH = 6.0, [Ca(II)] = 2 mM). Pb(II) partitioning onto these reactive metal-oxide surfaces increased with increasing reaction time (up to 7 d). In addition, the partitioning of Cu(II) and Zn(II) from the ESHA coating to the α-Fe 2 O 3 (0 0 0 1) substrate increased slightly with reaction time (2.4% and 3.7% for Cu(II) and Zn(II), respectively, after 3 h and 6.4% and 7.7% for Cu(II) and Zn(II), respectively, after 72 h of reaction time).

36 MATERIALS SCIENCE↗

Feasibility of using reactive silicate particles with temperature-responsive coatings to enhance the security of geologic carbon storage

The large-scale deployment of geologic carbon storage will require minimizing the risk of CO 2 leakage. Here we report on a novel strategy to seal leakage pathways by injecting functionalized reactive calcium silicate (CaSiO 3 ) particles. The particles consist of a mineral silicate core within a temperature-sensitive Poly(N,N-dimethylaminoethyl methacrylate) coating that limits contact between the core and the surrounding CO 2 (aq) above a switching temperature making them relatively unreactive deep in the subsurface. If the CO 2 leaks to shallower depths and cooler temperatures, the coatings would extend and enable the silicate core to react with CO 2(aq) to form solid carbonate precipitates that reduce the permeability of the fracture or flow path. A combined laboratory- and simulation-based investigation was conducted to explore key early-stage research questions related to the feasibility of this leakage management strategy. Sand columns were injected with either coated or uncoated CaSiO 3 particles and the permeability was measured before and after exposure to CO 2 . Experiments were conducted at 35 °C and 70 °C, a range that spans the switching temperature for the coatings. Results show that at the cooler temperature the coating effectively enabled reaction and permeability reduction. At higher temperatures, the coated particles limited mineral carbonation and the permeability decrease was minimal compared to columns with uncoated particles. Here, the morphology and location of the precipitates provides insight about permeability evolution. Model simulations of 2D radial particle transport from an injection point provided insight into the effects of particle size, coating properties, and concentrations of particles in several representative rock formations.

54 ENVIRONMENTAL SCIENCES↗

Pulsed sonication for alumina coatings on high-capacity oxides: Performance in lithium-ion cells

High-capacity xLi2MnO3•(1-x)LiMO2 (M=Ni, Mn, Co) oxides show relatively rapid performance degradation when cycled at voltages >4.5V vs. Li/Li+. Previous research has indicated that modifying the oxide surfaces with coatings, such as alumina, reduces cell impedance rise and improves capacity retention. In this article, we demonstrate pulsed-sonication as a rapid and effective approach for coating alumina on Li1.2Ni0.175Mn0.525Co0.1O2 (0.5Li2MnO3•0.5LiNi0.44Mn0.31Co0.25O2) particles. Oxide integrity and morphology is maintained after the sonochemical process and subsequent heat-treatment. Energy dispersive spectroscopy (EDS) X-ray elemental maps show uniform coating of all secondary particles. 27Al Magic Angle Spinning (MAS) NMR data confirm the presence of alumina and mainly indicate octahedral aluminum occupancy in a six-coordinate environment with oxygen. Full cells containing electrodes with the alumina-coated particles demonstrate lower initial impedance rise and better capacity retention during extended cycling to high voltages. However, the coating has a negligible effect on the voltage hysteresis and voltage fade behavior displayed by these oxides. The various data indicate that the pulsed sonochemical technique is a viable approach for coating oxide particles. The methodology described herein can easily be extended beyond alumina to include coatings such as AlF3, MgO, and MgF2.

1H NMR↗

Corrosion behavior of Ti-Al-N/Ti-Al duplex coating on AZ31 magnesium alloy in NaCl aqueous solution

In this study, Ti-Al-N/Ti-Al duplex coating was deposited on AZ31 magnesium alloy by magnetron sputtering with a Ti/Al composite target. Scanning electron microscopy and Auger electron spectroscopy were applied to investigate the morphology and elemental concentration of the obtained coating, respectively. The top layer was Ti-Al-N film with a Ti:Al:O:N ratio of 0.32:0.84:0.08:1, and the bottom layer was Ti-Al film with a Ti:O:Al ratio of 1.94:0.12:1. Each layer of this coating presented a developed columnar structure. The polarization test and immersion test were used to investigate corrosion behavior of the coated sample in 3.5 wt.% NaCl aqueous solution. The results showed that this duplex coating could protect the substrate effectively in NaCl aqueous solution. Nevertheless, several through-thickness micropores in the coating finally induced the failure of the coated AZ31 in the immersion test.

36 MATERIALS SCIENCE↗

Characterization of multilayer nitride coatings by electron microscopy and modulus mapping

This paper discusses multi-scale characterization of physical vapour deposited multilayer nitride coatings using a combination of electron microscopy and modulus mapping. Multilayer coatings with a triple layer structure based on TiAlN and nanocomposite nitrides with a nano-multilayered architecture were deposited by Cathodic arc deposition and detailed microstructural studies were carried out employing Energy Dispersive Spectroscopy, Electron Backscattered Diffraction, Focused Ion Beam and Cross sectional Transmission Electron Microscopy in order to identify the different phases and to study microstructural features of the various layers formed as a result of the deposition process. Modulus mapping was also performed to study the effect of varying composition on the moduli of the nano-multilayers within the triple layer coating by using a Scanning Probe Microscopy based technique. To the best of our knowledge, this is the first attempt on modulus mapping of cathodic arc deposited nitride multilayer coatings. This work demonstrates the application of Scanning Probe Microscopy based modulus mapping and electron microscopy for the study of coating properties and their relation to composition and microstructure. - Highlights: • Microstructure of a triple layer nitride coating studied at multiple length scales. • Phases identified by EDS, EBSD and SAED (TEM). • Nanolayered, nanocomposite structure of the coating studied using FIB and TEM. • Modulus mapping identified moduli variation even in a nani-multilayer architecture.

36 MATERIALS SCIENCE↗

Experimental investigation of grain boundaries misorientations and nano twinning induced strengthening on addition of silicon carbide in pulse electrodeposited nickel tungsten composite coating

Nanoindentation was performed on silicon carbide (SiC) reinforced pulse electrodeposited nickel-tungsten (Ni-W) composite coating. Addition of 5 vol.% of SiC in Ni-W coating increased the hardness from 10.31 ± 0.65 GPa to 14.32 ± 0.63 GPa and elastic modulus from 119.74 ± 3.15 GPa to 139.26 ± 2.09 GPa. Increased hardness and elastic modulus directly translates to the improved strengthening in the coating. An experimental investigation of strengthening mechanism was carried out in Ni-W-5 vol.% SiC alloy. Two simultaneous phenomena viz. grain refinement and increased internal strain was observed, which increased the dislocation density from 5.51 × 10{sup 18} m{sup −2} to 1.346 × 10{sup 19} m{sup −2} on reinforcement of 5 vol.% of SiC in Ni-W coating. Increased dislocation density promoted the formation of grain boundary misorientations and nano twinning. Low angle grain boundary, high angle grain boundary and nano twinning were identified using high resolution transmission electron microscope (HR-TEM) image and their role in strengthening mechanism was discussed in details. - Highlights: • SiC reinforced pulse electrodeposition Ni-W coating was deposited on steel. • Nanoindentation showed the increased mechanical properties on addition of SiC. • Grain refinement and increased internal strain was observed in Ni-W-SiC coating. • Dislocation density increased on reinforcement of SiC in Ni-W coating. • Increased dislocation density triggered grain boundary misorientation and twinning.

36 MATERIALS SCIENCE↗

Influencing mechanism of Al-containing Zn coating on interfacial microstructure and mechanical properties of friction stir spot welded Mg–steel joint

Highlights: • Al-containing Zn coating improved Mg–steel interfacial wettability during friction stir spot welding (FSSW). • Pre-existing Al{sub 5}Fe{sub 2} phase in coating on steel surface promoted Mg–steel metallurgical bonding. • A high tensile-shear load of 4.3 kN was obtained in FSSW AZ31–steel joint. - Abstract: 2.4 mm thick AZ31 Mg alloy sheet and 1.5 mm Q234 steel sheet with a hot-dipped Al-containing Zn coating were friction stir spot welded (FSSW) using a pinless tool. It was shown that the Al-containing Zn coating played a crucial role in joining the Mg alloy and steel during FSSW. The Zn coating observably improved the Mg–steel interfacial wettability during FSSW, and the Al{sub 5}Fe{sub 2} phase in the Zn coating on the steel substrate surface promoted the metallurgical bonding of Mg alloy and steel. It was confirmed that the Al{sub 5}Fe{sub 2} phase on the steel surface resulted from the reaction between the steel substrate and the Al in the Zn coating during hot-dipping, and was not related to the Al-containing Mg alloy substrate. The tensile-shear load of the FSSW Mg–steel joint reached 4.3 kN. The fracture of the joint occurred along the interface on the steel substrate side. The interface between the Al{sub 5}Fe{sub 2} layer and Mg alloy substrate was the weakest region of the Mg–steel joint.

77 NANOSCIENCE AND NANOTECHNOLOGY↗