Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cyclic loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Sensitivity of acoustic predictions to variation of input parameters

Rotor noise prediction codes predict the thickness and loading noise produced by a helicopter rotor, given the blade motion, rotor operating conditions, and fluctuating force distribution over the blade surface. However, the criticality of these various inputs, and their respective effects on the predicted acoustic field, have never been fully addressed. This paper examines the importance of these inputs, and the sensitivity of the acoustic predicitions to a variation of each parameter. The effects of collective and cyclic pitch, as well as coning and cyclic flapping, are presented. Blade loading inputs are examined to determine the necessary spatial and temporal resolution, as well as the importance of the chordwise distribution. The acoustic predictions show regions in the acoustic field where significant errors occur when simplified blade motions or blade loadings are used. An assessment of the variation in the predicted acoustic field is balanced by a consideration of Central Processing Unit (CPU) time necessary for the various approximations.

Brentner, Kenneth S.↗

Fatigue Tests with Random Flight Simulation Loading

Crack propagation was studied in a full-scale wing structure under different simulated flight conditions. Omission of low-amplitude gust cycles had a small effect on the crack rate. Truncation of the infrequently occurring high-amplitude gust cycles to a lower level had a noticeably accelerating effect on crack growth. The application of fail-safe load (100 percent limit load) effectively stopped subsequent crack growth under resumed flight-simulation loading. In another flight-simulation test series on sheet specimens, the variables studied are the design stress level and the cyclic frequency of the random gust loading. Inflight mean stresses vary from 5.5 to 10.0 kg/sq mm. The effect of the stress level is larger for the 2024 alloy than for the 7075 alloy. Three frequencies were employed: namely, 10 cps, 1 cps, and 0.1 cps. The frequency effect was small. The advantages and limitations of flight-simulation tests are compared with those of alternative test procedures such as constant-amplitude tests, program tests, and random-load tests. Various testing purposes are considered. The variables of flight-simulation tests are listed and their effects are discussed. A proposal is made for performing systematic flight-simulation tests in such a way that the compiled data may be used as a source of reference.

Schijve, J.↗

Constitutive modeling for isotropic materials (HOST)

The results of the first year of work on a program to validate unified constitutive models for isotropic materials utilized in high temperature regions of gas turbine engines and to demonstrate their usefulness in computing stress-strain-time-temperature histories in complex three-dimensional structural components. The unified theories combine all inelastic strain-rate components in a single term avoiding, for example, treating plasticity and creep as separate response phenomena. An extensive review of existing unified theories is given and numerical methods for integrating these stiff time-temperature-dependent constitutive equations are discussed. Two particular models, those developed by Bodner and Partom and by Walker, were selected for more detailed development and evaluation against experimental tensile, creep and cyclic strain tests on specimens of a cast nickel base alloy, B19000+Hf. Initial results comparing computed and test results for tensile and cyclic straining for temperature from ambient to 982 C and strain rates from 10(exp-7) 10(exp-3) s(exp-1) are given. Some preliminary date correlations are presented also for highly non-proportional biaxial loading which demonstrate an increase in biaxial cyclic hardening rate over uniaxial or proportional loading conditions. Initial work has begun on the implementation of both constitutive models in the MARC finite element computer code.

Lindholm, Ulric S.↗

Temperature-dependent cyclic response and microstructure of AlSi10Mg(Cu) alloy

Highlights: • The cyclic behavior of AlSi10Mg(Cu) alloy in LCF regime is temperature-dependent. • The transition temperature of the cyclic behavior is about 180 °C. • Microstructure transitions were observed with increasing temperature. - Abstract: In the present work, the cyclic stress response and microstructure evolution of AlSi10Mg(Cu) alloy at high temperature were investigated. Samples were tested at high temperature, under total strain control and tensile-compression loading (R = −1) until failure. The cyclic stress response was analyzed, as well as the microstructures were examined by TEM. The results demonstrated that the cycle stress response of the studied alloy is experimental temperature dependence. Microstructure analysis indicated the precipitated phase was disruptive changed by high temperature compared to the as-received alloy. A lot of coherent β″-Mg{sub 2}Si precipitates and GP zones were observed in the as-received alloy, resulting in sustaining cyclic hardening by pinning effect. At high temperature, the vast majority of the tiny coherency precipitates and clusters transformed to the large semi-coherency Q′ and β′-Mg{sub 2}Si precipitates, leading to the sharp decrease of pinning number and the change of dislocation interaction mechanism, which is believed to be one of the reasons for softening. Another reason is that high temperatures can promote dislocations movement.

36 MATERIALS SCIENCE↗

In-situ neutron diffraction investigation on twinning/detwinning activities during tension-compression load reversal in a twinning induced plasticity steel

The tension-compression type of load reversal produces an asymmetric cyclic tension-compression behavior and varied yielding stresses in the subsequent monotonic tension and compression in a twinning induced plasticity steel. The micromechanical behavior was elucidated via the evolutions of the stacking fault probability and the grain orientation density captured by in-situ neutron diffraction. The latter indicates more profound detwinning activities in a reversal from tension to compression than those from compression to tension and more twinning involves in monotonic tension than in compression. In conclusion, this is confirmed by the calculated twinning activities in monotonic tension and compression using the visco-plastic self-consistent model.

TWIP↗

Specialists Meeting on Rotorcraft Dynamics, Moffett Field, Calif., February 13-15, 1974, Proceedings

Analysis of specific problems in rotorcraft dynamics. Topics include hingeless rotor theory, dynamic stall modelling, periodic systems identification, analysis of complex systems with phasing matrices, flapping stability, flap-lag dynamics at high advance ratios, finite element analysis and fuselage free-vibration characteristics, coupled rotor/frame vibration methods, gust response characteristics with unsteady stall effects, antiresonance theory, cyclic feathering motions and dynamic loads, control load envelope shaping, rotor aeroelasticity, use of Floquet theory, theory of proprotors and tilt-rotors, two-bladed teetering rotors, stability of air and ground resonance, vertical-plane pendulum absorbers, multicyclic jet-flap control, engine/frame interface dynamics, and others. The minutes of the question and answer periods following the presentations are presented in the supplement. Individual items are announced in this issue.

Source record↗

Elevated temperature fatigue testing of metals

Material characterization and evaluation conducted for the purpose of calculating fatigue crack initiation lives of components operating at elevated temperatures are discussed. The major technology areas needed to perform a life prediction of an aircraft turbine engine hot section component and the steps required for life prediction are outlined. These include: the determination of the operating environment, the calculation of the thermal and mechanical loading of the component, the cyclic stress strain and creep behavior of the material required for structural analysis, the structural analysis to determine the local stress strain temperature time response of the material at the critical location in the component, and from a knowledge of the fatigue, creep, and failure resistance of the material, a prediction of the life of the component.

Hirschberg, M. H.↗

Elevated temperature fatigue testing of metals

The major technology areas needed to perform a life prediction of an aircraft turbine engine hot section component are discussed and the steps required for life prediction are outlined. These include the determination of the operating environment, the calculation of the thermal and mechanical loading of the component, the cyclic stress-strain and creep behavior of the material required for structural analysis, and the structural analysis to determine the local stress-strain-temperature-time response of the material at the critical location in the components. From a knowledge of the fatigue, creep, and failure resistance of the material, a prediction of the life of the component is made. Material characterization and evaluation conducted for the purpose of calculating fatigue crack initiation lives of components operating at elevated temperatures are emphasized.

Hirschberg, M. H.↗

Design and fabrication of brazed Rene 41 honeycomb sandwich structural panels for advanced space transportation systems

The design and fabrication of two large brazed Rene 41 honeycomb panels, the establishment of a test plan, the design and fabrication of a test fixture to subject the panels to cyclic thermal gradients and mechanical loads equivalent to those imposed on an advanced space transportation vehicle during its boost and entry trajectories are discussed. The panels will be supported at four points, creating three spans. The outer spans are 45.7 cm (18 in.) and the center span 76.2 cm (30 in). Specimen width is 30.5 cm (12 in.). The panels were primarily designed by boost conditions simulated by subjecting the panels to liquid nitrogen, 77K (-320 F) on one side and 455K (360 F) on the other side and by mechanically imposing loads representing vehicle fuel pressure loads. Entry conditions were simulated by radiant heating to 1034K (1400 F). The test program subjected the panels to 500 boost thermal conditions. Results are presented.

Hepler, A. K.↗

Vehicle test report: Jet Industries Electra Van 600

The Electra Van 600, an electric vehicle, was tested. Tests were performed to characterize parameters of the Electra Van 600 and to provide baseline data to be used for comparison of improved batteries and to which will be incorporated into the vehicle. The vehicle tests concentrated on the electrical drive subsystem, the batteries, controller, and motor; coastdowns to characterize the road load and range evaluation for cyclic and constant speed conditions; and qualitative performance was evaluated. It is found that the Electra Van 600 range performance is approximately equal to the majority of the vehicles tested previously.

Price, T. W.↗

Aircraft engine hot section technology: An overview of the HOST Project

NASA sponsored the Turbine Engine Hot Section Technology (HOST) Project to address the need for improved durability in advanced aircraft engine combustors and turbines. Analytical and experimental activities aimed at more accurate prediction of the aerothermal environment, the thermomechanical loads, the material behavior and structural responses to loads, and life predictions for cyclic high-temperature operation were underway for the last 7 years. The project has involved representatives from six engineering disciplines who are spread across three work sectors (industry, academia, and NASA). The HOST Project not only initiated and sponsored 70 major activities, but was also the keystone in joining the multiple disciplines and work sectors to focus on critical research needs. A broad overview of the project is given along with initial indications of the project's impact.

Sokolowski, Daniel E.↗

Constitutive modeling for isotropic materials (HOST)

The results of the third year of work on a program which is part of the NASA Hot Section Technology program (HOST) are presented. The goals of this program are: (1) the development of unified constitutive models for rate dependent isotropic materials; and (2) the demonstration of the use of unified models in structural analyses of hot section components of gas turbine engines. The unified models selected for development and evaluation are those of Bodner-Partom and of Walker. A test procedure was developed for assisting the generation of a data base for the Bodner-Partom model using a relatively small number of specimens. This test procedure involved performing a tensile test at a temperature of interest that involves a succession of strain-rate changes. The results for B1900+Hf indicate that material constants related to hardening and thermal recovery can be obtained on the basis of such a procedure. Strain aging, thermal recovery, and unexpected material variations, however, preluded an accurate determination of the strain-rate sensitivity parameter is this exercise. The effects of casting grain size on the constitutive behavior of B1900+Hf were studied and no particular grain size effect was observed. A systematic procedure was also developed for determining the material constants in the Bodner-Partom model. Both the new test procedure and the method for determining material constants were applied to the alternate material, Mar-M247 . Test data including tensile, creep, cyclic and nonproportional biaxial (tension/torsion) loading were collected. Good correlations were obtained between the Bodner-Partom model and experiments. A literature survey was conducted to assess the effects of thermal history on the constitutive behavior of metals. Thermal history effects are expected to be present at temperature regimes where strain aging and change of microstructure are important. Possible modifications to the Bodner-Partom model to account for these effects are outlined. The use of a unified constitutive model for hot section component analyses was demonstrated by applying the Walker model and the MARC finite-element code to a B1900+Hf airfoil problem.

Chan, Kwai S.↗

Aircraft engine hot section technology: An overview of the HOST Project

NASA sponsored the Turbine Engine Hot Section (HOST) project to address the need for improved durability in advanced aircraft engine combustors and turbines. Analytical and experimental activities aimed at more accurate prediction of the aerothermal environment, the thermomechanical loads, the material behavior and structural responses to loads, and life predictions for cyclic high temperature operation were conducted from 1980 to 1987. The project involved representatives from six engineering disciplines who are spread across three work disciplines - industry, academia, and NASA. The HOST project not only initiated and sponsored 70 major activities, but also was the keystone in joining the multiple disciplines and work sectors to focus on critical research needs. A broad overview of the project is given along with initial indications of the project's impact.

Sokolowski, Daniel E.↗

Lifetime Reliability Evaluation of Structural Ceramic Parts with the CARES/LIFE Computer Program

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker equation. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), Weibull's normal stress averaging method (NSA), or Batdorf's theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Two example problems demonstrating cyclic fatigue parameter estimation and component reliability analysis with proof testing are included.

Nemeth, Noel N.↗

Time-dependent reliability analysis of ceramic engine components

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing either the power or Paris law relations. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Two example problems demonstrating proof testing and fatigue parameter estimation are given.

Nemeth, Noel N.↗

Durability evaluation of ceramic components using CARES/LIFE

The computer program CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program. CARES/LIFE accounts for the phenomenon of subcritical crack growth (SCG) by utilizing the power law, Paris law, or Walker equation. The two-parameter Weibull cumulative distribution function is used to characterize the variation in component strength. The effects of multiaxial stresses are modeled using either the principle of independent action (PIA), the Weibull normal stress averaging method (NSA), or the Batdorf theory. Inert strength and fatigue parameters are estimated from rupture strength data of naturally flawed specimens loaded in static, dynamic, or cyclic fatigue. Application of this design methodology is demonstrated using experimental data from alumina bar and disk flexure specimens which exhibit SCG when exposed to water.

Nemeth, Noel N.↗

Fatigue fracture in thin plates subjected to tensile and shearing loads - Crack tip fields, J integral and preliminary experimental results

In one scenario of a crack in an airplane fuselage, the crack is subjected to cyclic tensile and out of plane shearing loads. To predict the fatigue crack growth in such a situation, experiments are being performed to measure the crack growth rate in laboratory specimens subjected to similar loadings. The mechanics of this problem are reviewed, the energy release rate is calculated and designs for an experiment are discussed along with some preliminary experimental observations.

Zehnder, Alan T.↗