Search NASA⌕ Search

SEARCH · Search NASA

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

F4‐TCNQ as an Additive to Impart Stretchable Semiconductors with High Mobility and Stability

Abstract Numerous strategies are developed to impart stretchability to polymer semiconductors. Although these methods improve the ductility, mobility, and stability of such stretchable semiconductors, they nonetheless still need further improvement. Here, it is shown that 2,3,5,6‐tetrafluoro‐7,7,8,8‐tetracyanoquinodimethane (F4‐TCNQ) is an effective molecular additive to tune the properties of a diketopyrrolopyrrole‐based (DPP‐based) semiconductor. Specifically, the addition of F4‐TCNQ is observed to improve the ductility of the semiconductor by altering the polymer’s microstructures and dynamic motions. As a p‐type dopant additive, F4‐TCNQ can also effectively enhance the mobility and stability of the semiconductor through changing the host polymer’s packing structures and charge trap passivation. Upon fabricating fully stretchable transistors with F4‐TCNQ‐DPP blended semiconductor films, it is observed that the resulting stretchable transistors possess one of the highest initial mobility of 1.03 cm 2 V −1 s −1 . The fabricated transistors also exhibit higher stability (both bias and environmental) and mobility retention under repeated strain, compared to those without F4‐TCNQ additive. These findings offer a new direction of research on stretchable semiconductors to facilitate future practical applications.

Mun, Jaewan↗

In Situ TEM Investigation of ZnO Nanowires during Sodiation and Lithiation Cycling

The development of sodium-ion batteries has drawn lots of attention recently due to the low-cost and eco-friendly sodium source. However, a fundamental understanding of the sodiation behavior for commonly used electrode materials is still limited. Here, combining in situ transmission electron microscopy, aberration-corrected scanning transmission electron microscopy, and ex situ battery cycling tests, the lithiation and sodiation behavior of ZnO nanowires is investigated. The findings show a direct correlation between the mechanical behavior of the lithiated/sodiated ZnO nanowires and their electrochemical cyclability. The mechanical brittleness of LiZn and the formation of nanocracks lead to the poor cyclability of Li-ion batteries with a ZnO anode. However, the sodiated ZnO nanowires show profuse dislocation plasticity. The observed high-density dislocations offer the sodiated ZnO anode more ductility and subsequently better cyclability than its Li-ion counterpart. The results reveal the importance of understanding the correlation between mechanical properties of battery electrodes and their cycling abilities.

Asayesh-Ardakani, Hasti↗

A Composite Modeling Analysis of the Deformation Behavior of Medium Manganese Steels

The deformation behavior of medium manganese steels was evaluated with uniaxial tensile testing and the results were correlated with predictions of a composite model shown previously to provide design insight into the development of multi-phase steels with third-generation advanced high strength steel (3GAHSS) properties. An equilibrium thermodynamic-based methodology to design microstructures containing systematic amounts of metastable austenite with controlled stability against transformation is presented. The analysis is based on Mn enrichment of austenite during intercritical annealing of medium Mn (7 and 10 wt pct.) low carbon (0.1 and 0.15 wt pct) steels. The steels were produced as laboratory heats that were hot and cold rolled prior to annealing. After annealing the microstructures consisted primarily of either a matrix of fine grained ferrite with austenite contents between 32.6 and 45.2 wt pct (7Mn, 0.1C steels) or a matrix of martensite with various amounts of austenite in the higher Mn steel. The different intercritical annealing conditions produced steels with wide variations in austenite contents and austenite compositions (Mn and C contents) resulting in steels with significant variations in austenite stability. Predictions based on the composite analysis with different assumed flow behaviors for the individual constituents and stability functions for the meta-stable austenite are presented and shown to accurately predict strength-ductility combinations over a range of austenite volume fractions for the 7Mn steel. Applicability of the composite analysis is extended to consider the deformation behavior of the 10Mn steel and evaluate other possible microstructural combinations leading to 3GAHSS properties.

36 MATERIALS SCIENCE↗

Inverse measurement of stiffness by the normalization technique for J-integral fracture toughness

The single specimen normalization technique for J-integral fracture toughness has been successfully employed by several researchers to study the strongly non-linear fracture response of ductile semicrystalline polymers. As part of the normalization technique the load and the plastic component of displacement are normalized. The normalized data is then fit with a normalization function that approximates a power law for small displacements that are dominated by blunting and smoothly transitions to a linear relationship for large displacements that are dominated by stable crack extension. Particularly for very ductile polymers the compliance term used to determine the plastic displacement can dominate the solution and small errors in determining the elastic modulus can lead to large errors in the normalization or even make it ill-posed. This can be further complicated for polymers where the elastic modulus is strong strain rate dependent and simply using a 'quasistatic' modulus from a dogbone measurement may not equate to the dominant strain rate in the compact tension specimen. The current work proposes directly measuring the compliance of the compact tension specimen in the solution of J-integral fracture toughness and then solving for the elastic modulus. By comparison with a range of strain rate data the dominant strain rate can then be determined.

36 MATERIALS SCIENCE↗

Microstructural modification of a high-pressure die-cast A380 alloy through friction stir processing and its effect on mechanical properties

Aluminum alloy A380 is one of the major high-pressure die-cast (HPDC) alloys fabricated in the die casting sector. However, microstructural features such as shrinkage and gas porosity, entrapped oxide inclusions, change in the morphology of eutectic Si particles as a function of casting location, and the presence of multiple second phase particulates, especially Fe-bearing phases in HPDC A380 alloy results in limited ductility, thus, affecting its structural application. However, through proper modification of the as-cast microstructure, it is possible to improve the mechanical performance of alloy A380. In this study, we report the effect of friction stir processing (FSP), a well-known severe plastic deformation (SPD) and thermomechanical processing tool for selective microstructural modification, on A380. FSP effectively refines the as-cast microstructure and breaks down the coarse Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. Additionally, FSP eliminates porosity that acts as crack initiation sites, leading to improved mechanical strength and ductility.

Friction stir processing, Aluminum alloys, Mechani↗

Improving the Mechanical Properties of Cast Aluminum Via Ultrasonication-Induced Microstructural Refinement

One barrier to the broader use of cast aluminum alloys in automotive applications is their poor mechanical properties, especially compared to wrought materials. This study investigates the use of ultrasound to refine the microstructure of cast aluminum alloys during solidification and thus improve their mechanical properties. An A356 aluminum alloy (Al-Si-Mg) with added Fe (to mimic a recycle-grade alloy) was cast in a graphite mold with the simultaneous application of ultrasound. Tensile specimens were extracted from the castings and heat treated to a T6 temper. Ultrasonication during casting transformed the morphology of primary aluminum grains from dendritic (~140 microns in size) to globular (~36 microns in size), increased the ultimate tensile strength by 10 %, and tripled the ductility compared to casting without ultrasound. This improvement in strength and ductility demonstrates the potential for ultrasonic processing to improve the performance of cast aluminum alloys without altering their chemistry or additional post-processing.

Aluminum, Solidification, Ultrasound, Grain refinm↗

Enhanced Tensile and Tear Toughness Properties of Thin-Wall Vacuum-Assisted High-Pressure Die-Cast Aural-5 Alloy by Friction Stir Processing

Steadily rising demand for glider weight reduction has driven the development of vacuum-assisted high-pressure die-cast (HPDC) Al-alloys for automotive structural components. Aural-5 is a strontium-modified HPDC alloy utilizing manganese (Mn) to reduce die soldering, eliminating detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. HPDC Aural-5 contains shrinkage porosity, dendrites with Al-Si eutectic colonies, externally solidified crystals (ESCs), shear-band structure, and large second-phase particulates. Porosity, ESCs and large second-phase particles work as crack initiation sites, negatively impacting tensile properties. In this study, friction stir processing (FSP) is employed for microstructural modification of a thin-walled HPDC Aural-5 by eliminating porosity and breaking down dendrites, second-phase particles, eutectic colonies, ESCs and shear-band structures to create wrought microstructure with homogenized particle distribution. Mechanical property characterization indicates ~30% and ~35% enhancement in yield strength and ductility and associated marked effects on ~69% improvement in tear toughness according to the ASTM B871 test.

Friction stir processing, Aural-5, Strength, Tear ↗

Scale-Up of Friction Self-piercing Riveting Process for Multi-material Joints

A single-class joining process known as “friction self-piercing riveting (F-SPR)” has been developed for joining various low-ductility lightweight materials on a laboratory scale. The frictional heat generated during the F-SPR process improved local ductility, resulting in crack-free joints and robust mechanical performance. This innovative joining technology was further advanced through the scale-up of the process using a new system with several key features (e.g., automatic rivet feeding and clamping system, vacuum system) toward industry readiness. The new integrated F-SPR systems were effectively demonstrated for joining different material combinations (e.g., carbon fiber composite to 7075 Al alloy, 7075 Al alloy to 7075 Al alloy, and 7075 Al alloy to casting Al Aural 5) with a unified technique. Crack-free joint with adequate mechanical interlocking resulted in good mechanical joint strength for each material combination. Then, the process was successfully scaled up by producing multiple joints without any cracks on larger CFC-Al and Al-Al components by the new integrated system, bringing it closer to industrial application.

Lim, Yong Chae [ORNL] (ORCID:0000000321773988)↗

Mechanical behavior of polyamide-6 after combined photo-oxidative and hygrothermal aging

The effect of moisture on the photo-oxidative degradation of polyamide-6 (PA-6) was studied by analyzing the mechanical response after two different accelerated aging procedures. In the first aging procedure, the PA-6 was only exposed to ultra-violet (UV) radiation at 60 °C. In the second procedure, the same duration of UV radiation was periodically interrupted while the relative humidity was raised to 100%. Diffusion-limited and nominally homogeneous degradation conditions were investigated using bulk and film specimens, respectively. Accelerated UV aging reduced the ductility of PA-6, but the additional hygrothermal exposure had no effect on the ductility or strength, indicating that humidity did not influence the photo-oxidation of PA-6. In conclusion, this finding contrasts with previous studies that found thermo-oxidation of PA-6 was accelerated by moisture.

36 MATERIALS SCIENCE↗

A method for evaluating the fatigue crack growth in spiral notch torsion fracture toughness test

The spiral notch torsion test (SNTT) has been a recent breakthrough in measuring fracture toughness for different materials, including metals, ceramics, concrete, and polymers composites. Due to its high geometry constraint and unique loading condition, SNTT can be used to measure the fracture toughness with smaller specimens without concern of size effects. The application of SNTT to brittle materials has been proved to be successful. The micro-cracks induced by original notches in brittle materials could ensure crack growth in SNTT samples. Therefore, no fatigue pre-cracks are needed. The application of SNTT to the ductile material to generate valid toughness data will require a test sample with sufficient crack length. Fatigue pre-crack growth techniques are employed to introduce sharp crack front into the sample. Previously, only rough calculations were applied to estimate the compliance evolution in the SNTT crack growth process, while accurate quantitative descriptions have never been attempted. This generates an urgent need to understand the crack evolution during the SNTT fracture testing process of ductile materials. Here, the newly developed governing equations for SNTT crack growth estimate are discussed in the paper.

36 MATERIALS SCIENCE↗

Predicting grid-size-dependent fracture strains of DP980 with a microstructure-based post-necking model

Ductile fracture is a local phenomenon, and it is well established that fracture strain levels depend on both stress triaxiality and the resolution (grid size) of strain measurements. Two-dimensional plane strain post-necking models with different representative volume element (RVE) sizes are used to predict the size-dependent fracture strain of a commercial dual-phase steel, DP980. The models are generated from the actual microstructures, and the individual phase flow properties and literature-based individual phase damage parameters for the Johnson-Cook model are used for ferrite and martensite. A monotonic relationship is predicted: the smaller the model size, the higher the fracture strain. Thus, a general framework is developed to quantify the size-dependent fracture strains for multiphase materials. In addition to the RVE sizes, the influences of intrinsic microstructure features, i.e., the flow curve and fracture strains of the two constituent phases, on the predicted fracture strains also are examined. Application of the derived fracture strain versus RVE size relationship is demonstrated with large clearance trimming simulations with different element sizes.

Cheng, G. (ORCID:0000000268604420)↗

Preface to the special volume on the third Sandia Fracture Challenge

The mounting reliance on computational simulations to predict all aspects of the lifecycle of a mechanical system, from fabrication to failure, has prompted the mechanics community to selfassess its abilities to perform those predictions. Benchmark problems in mechanics that compare simulations that use different computational approaches with experiments have sprung up lately, including the NIST AM-Bench looking at additively manufactured (AM) materials (https://www.nist.gov/ambench),the Contact-Mechanics Challenge (Miiser, 2017) considering adhesion between two nominally flat surfaces, Numisheet providing semiannual benchmarking activities in sheet metal forming (http://numisheet2018.org),and the Sandia Fracture Challenge (SFC) (Boyce, 2014 and Boyce, 2016) investigating ductile failure. The previous SFCs have shown that progress has been made in computations of ductile failure, but improvements still can be made, hence the third Sandia Fracture Challenge (SFC3), the subject of this Special Volume. The most recent installment of SFC is building on previous successes and tackling the difficult problem of fracture in an AM 316L stainless steel structure.

42 ENGINEERING↗

A dislocation-based, strain–gradient–plasticity strengthening model for deformation processed metal–metal composites

Deformation processed metal–metal composites (DMMCs) are high-strength, high-electrical conductivity composites developed by severe plastic deformation of two ductile metal phases. The extraordinarily high strength of DMMCs is underestimated using the rule of mixture (or volumetric weighted average) of conventionally work-hardened metals. A dislocation-density-based, strain–gradient–plasticity model is proposed to relate the strain-gradient effect with the geometrically necessary dislocations emanating from the interface to better predict the strength of DMMCs. The model prediction was compared with our experimental findings of Cu–Nb, Cu–Ta, and Al–Ti DMMC systems to verify the applicability of the new model. The results show that this model predicts the strength of DMMCs better than the rule-of-mixture model. The strain-gradient effect, responsible for the exceptionally high strength of heavily cold worked DMMCs, is dominant at large deformation strain since its characteristic microstructure length is comparable with the intrinsic material length.

36 MATERIALS SCIENCE↗

The granular and polymer composite nature of kerogen-rich shale

In the past decade, mechanical, physical, and chemical characterization of reservoir shale rocks, such as the Woodford shale, which is kerogen-rich shale (KRS), has moved toward micro- and nanoscale testing and analyses. Nanoindentation equipment is now widely used in many industrial and university laboratories to measure shale anisotropic Young’s moduli, kerogen stiffness, plastic yield parameters, and other isotropic and anisotropic poromechanical and viscoelastic properties. However, to date, failure analyses of KRS and the effects of organic components on the tensile strength have not been observed or measured at the micro- or nanoscales. In this study, preserved kerogen-rich Woodford shale samples manufactured in micro-beam and micro-pillar geometries were mechanically tested and brought to failure in tension and compression, respectively. These tests were conducted in situ using a nanoindenter inside a scanning electron microscope (SEM). The load versus displacement curves of prismatic micro-cantilever beams were analyzed in light of high-resolution images collected during tensile fracture initiation, propagation, and ultimately sample failure. The micro-pillar geometries were subjected to a uniaxial compressive load and were also brought to failure while capturing measurements of stress and strain. It was found that, within just a few hundred microns of the KRS microcantilever beams, both brittle and ductile failure modes were observed. In the ductile plastic domain, strain-softening and strain-hardening behaviors were identified and characterized. These were not due to confining stress variations, but due to the volume of the organic matter and the way it is interlaced with the shale minerals in and around the failure planes. The tensile strength characteristics and the large modulus of toughness of kerogen, which is a cross-linked polymer, definitely weigh heavily in our engineering field applications, such as hydraulic fracking, which is a Mode I tensile fracture opening and propagation phenomenon. This practice demands that, due to the complex composite nature of KRS, mechanical characterization be not only for unconfined compressive strength but also for unconfined tensile strength and moduli of ruptures. At the end of this study, the need for nanometer scale mechanical characterization of KRS will become apparent. Furthermore, these nano- and micro-scale shale failure tests reinforce our previous understanding of the heterogeneous composite nature of Woodford KRS and its complex behavior, as well as other source shale reservoir formations.

58 GEOSCIENCES↗

Suppression of Void Nucleation in High-Purity Aluminum via Dynamic Recrystallization

The process of ductile fracture in metals often begins with void nucleation at second-phase particles and inclusions. Previous studies of rupture in high-purity face-centered-cubic metals, primarily aluminum (Al), concluded that second-phase particles are necessary for cavitation. A recent study of tantalum (Ta), a body-centered-cubic metal, demonstrated that voids nucleate readily at deformation-induced dislocation boundaries. These same features form in Al during plastic deformation. This study investigates why void nucleation was not previously observed at dislocation boundaries in Al. Here, we demonstrate that void nucleation is impeded in Al by room-temperature dynamic recrystallization (DRX), which erases these boundaries before voids can nucleate at them. If dislocation cells reform after DRX and before specimen separation by necking, voids nucleation is observed. These results indicate that dislocation substructures likely plays an important role in ductile rupture.

36 MATERIALS SCIENCE↗

A New Recycled Al–Si–Mg Alloy for Sustainable Structural Die Casting Applications

The use of secondary aluminum for structural components in the automotive industry is limited by the high Fe contents in recycled alloys which often result in the formation of brittle β-Al 5 FeSi phase which reduces the ductility of aluminum castings. In this study, a new secondary Al-Si-Mg alloy with high Fe content (about 0.44 wt.%) was developed for die casting applications. Based on thermodynamic modeling, manganese was added to obtain a designed Fe-to-Mn ratio of 2 which successfully suppressed the formation of β-Al 5 FeSi phase, by forming α-Al 15 (Fe,Mn) 3 Si 2 phase with rounded or hexagonal morphology. Additionally, a fine needle-like π-Al 8 FeMg 3 Si 2 phase was also formed within the eutectic regions. The new recycled alloy showed comparable mechanical properties in as-cast and heat treated (T5 and T6) conditions to three major primary die cast alloys (≤ 0.2 wt.% Fe) with similar composition. Ductility up to 7.4% from tensile elongation was achieved in as-cast recycled alloy due to the modification and refinement of α-Al 15 (Fe,Mn) 3 Si 2 by Mn and Sr additions. Tensile elongation was further improved to 9.1% after T6 treatment as a result of dissolution of π-Al 8 FeMg 3 Si 2 phase, defragmentation of α-Al 15 (Fe,Mn) 3 Si 2 and the spheroidization of Si phase. This new alloy provides a promising path for increasing usage of recycled aluminum with high Fe content in structural die castings for automotive and other applications.

36 MATERIALS SCIENCE↗

Impact of Low-Temperature Neutron Irradiation on Tensile Behavior of Base Metal and Electron-Beam Welded 316L Stainless Steel

Here, a study of 316L type stainless steel in its base metal and electron-beam (e-beam) welded conditions was performed to observe the effects of low-temperature (60 °C to 100 °C) neutron irradiation on the tensile behavior of the samples. Fractography was used in understanding the tensile-tested fracture surfaces of the 316L samples in these different forms with the characterization of the both base metal and welded samples using electron microscopy. Irradiation of the tensile specimens made free of defects of cutting and mechanical polishing showed a reduction in their tensile ductility with increased radiation-induced hardening up to 1.40 × 10 19 n/cm 2 (E > 0.1 MeV) fluence that corresponds to 1.1x 10 -2 dpa, even at the low irradiation temperatures. These low-temperature neutron irradiated base metal and e-beam welded 316L specimens also consisted of closely similar fracture surfaces characteristic of ductile rupture.

36 MATERIALS SCIENCE↗

The Influence of Nominal Composition on the Microstructure, Tensile Properties, and Weldability of Cast Monel Alloys

Cast Monel alloys are used in many industrial applications that require a combination of good mechanical properties and excellent resistance to corrosion. Despite relative widespread use, there has been limited prior research investigating the fundamental composition–structure–property relationships. Here in this work, microstructural characterization, thermal analysis, electron probe microanalysis, tensile testing, and Varestraint testing were used to assess the effects of variations in nominal composition on the solidification path, microstructure, mechanical properties, and solidification cracking susceptibility of cast Monel alloys. It was found that Si segregation caused the formation of silicides at the end of solidification in grades containing at least 3 wt pct Si. While increases to Si content led to significant improvements in strengthening due to the precipitation of β 1 -Ni 3 Si, the silicide eutectics acted as crack nucleation sites during tensile loading which severely reduced ductility. The solidification cracking susceptibility of low-Si Monel alloys was found to be relatively low. However, increases to Si concentration and the onset of associated eutectic reactions increased the solidification temperature range and drastically reduced cracking resistance. Increases in the Cu and Mn concentrations were found to reduce the solubility limit of Si in austenite which promoted additional eutectic formation and exacerbated the reductions in ductility and/or weldability.

36 MATERIALS SCIENCE↗