Search NASA⌕ Search

SEARCH · Search NASA

Results for “Defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Vibration detection of component operability

In order to prevent catastrophic failure and eliminate unnecessary periodic maintenance in the Space Shuttle Orbiter dynamic components, instrumentation for detecting incipient failure in these components is required. This study investigated the utilization of vibrational phenomena as one of the principal physical parameters on which to base the design of this instrumentation. Baseline vibration data was collected from three aircraft type fans and two aircraft type pumps over a frequency range from a few Hertz to greater than 300 kHz. The baseline data included spectrum analysis of the vibration and detected carrier signals, as well as several non-spectrum parameters. Several defects were introduced into the five test items, and all defects were detected by at least one of the parameters with a margin of at least 2:1 over the worst case baseline.

Baird, B.↗

Merging of aircraft trailing vortices

A merging-distance criterion for equal-strength corotational vortices is derived from low-turbulence wind-tunnel flow-visualization data. The vortex separation distance is normalized by defining a vortex core diameter based on circulation defect and angular-momentum defect. Merging may take place for larger separation distances than predicted from earlier two-dimensional inviscid calculations, which indicates that viscosity and possibly three-dimensional effects are important factors in the merging phenomenon. Hot-wire velocity distributions and rolling-moment measurements show that attenuation of the vortex hazard is associated with vortex merging.

Brandt, S. A.↗

EPR and transient capacitance studies on electron-irradiated silicon solar cells

One and two ohm-cm solar cells irradiated with 1 MeV electrons at 30 C were studied using both EPR and transient capacitance techniques. In 2 ohm-cm cells, Si-G6 and Si-G15 EPR spectra and majority carrier trapping levels at (E sub V + 0.23) eV and (E sub V + 0.38) eV were observed, each of which corresponded to the divacancy and the carbon-oxygen-vacancy complex, respectively. In addition, a boron-associated defect with a minority carrier trapping level at (E sub C -0.27) eV was observed. In 1 ohm-cm cells, the G15 spectrum and majority carrier trap at (E sub V + 0.38) eV were absent and an isotropic EPR line appeared at g = 1.9988 (+ or - 0.0003); additionally, a majority carrier trapping center at (E sub V + 0.32) eV, was found which could be associated with impurity lithium. The formation mechanisms of these defects are discussed according to isochronal annealing data in electron-irradiated p-type silicon.

Lee, Y. H.↗

Investigation of the double exponential in the current-voltage characteristics of silicon solar cells

A theoretical analysis is presented of certain peculiarities of the current-voltage characteristics of silicon solar cells, involving high values of the empirical constant A in the diode equation for a p-n junction. An attempt was made in a lab experiment to demonstrate that the saturation current which is associated with the exponential term qV/A2kT of the I-V characteristic, with A2 roughly equal to 2, originates in the space charge region and that it can be increased, as observed on ATS-1 cells, by the introduction of additional defects through low energy proton irradiation. It was shown that the proton irradiation introduces defects into the space charge region which give rise to a recombination current from this region, although the I-V characteristic is, in this case, dominated by an exponential term which has A = 1.

Wolf, M.↗

Quantitative ultrasonic evaluation of mechanical properties of engineering materials

Current progress in the application of ultrasonic techniques to nondestructive measurement of mechanical strength properties of engineering materials is reviewed. Even where conventional NDE techniques have shown that a part is free of overt defects, advanced NDE techniques should be available to confirm the material properties assumed in the part's design. There are many instances where metallic, composite, or ceramic parts may be free of critical defects while still being susceptible to failure under design loads due to inadequate or degraded mechanical strength. This must be considered in any failure prevention scheme that relies on fracture analysis. This review will discuss the availability of ultrasonic methods that can be applied to actual parts to assess their potential susceptibility to failure under design conditions.

Vary, A.↗

CODSTRAN: Composite durability structural analysis

CODSTRAN (COmposite Durability STRuctural ANalysis) is an integrated computer program being developed for the prediction of defect growth and fracture of composite structures subjected to service loads and environments. CODSTRAN is briefly described with respect to organization, capabilities and present status. Application of CODSTRAN current capability to a flat composite laminate with a center slit which was subjected to axial tension loading predicted defect growth which is in good agreement with C-scan ultrasonic test records.

Chamis, C. C.↗

High-energy electron-induced damage production at room temperature in aluminum-doped silicon

DLTS and EPR measurements are reported on aluminum-doped silicon that was irradiated at room temperature with high-energy electrons. Comparisons are made to comparable experiments on boron-doped silicon. Many of the same defects observed in boron-doped silicon are also observed in aluminum-doped silicon, but several others were not observed, including the aluminum interstitial and aluminum-associated defects. Damage production modeling, including the dependence on aluminum concentration, is presented.

Corbett, J. W.↗

The estimation of residual strength of composites by acoustic emission

The strength of unidirectional fibrous composite materials was measured as a function of the acoustic emission. Specimens of glass fibers and carbon fibers in an epoxy matrix were tested to fracture. Many of the specimens were with existing defects. It was shown, analytically and experimentally, that defective material starts to emit acoustic waves at a much lower stress level than nondefective material. It was found that for glass fiber material, the ultimate strength of the composite is proportional to the stress level for which a specific number of acoustic emission counts was reached. For carbon fiber material, this phenomenon is less pronounced.

Rotem, A.↗

Rheology of composite solid propellants during motor casting

Results of casting studies are reviewed so as to define the viscosity criteria insuring the fabrication of defect-free grains. The rheology of uncured propellants is analyzed showing that a realistic assessment of a propellant's flow properties must include measurement of viscosity as a function of shear stress and time after curing agent. Methods for measuring propellant viscosity are discussed, with particular attention given to the Haake-Rotovisko rotational viscometer. The effects of propellant compositional and processing variables on apparent viscosity are examined, as are results relating rheological behavior to grain defect formation during casting.

Klager, K.↗

CODSTRAN - Composite durability structural analysis

CODSTRAN (COmposite Durability STRucture ANalysis) a NASA Lewis Center computer program for the prediction of defect growth and fracture of composite structures when subjected to service loads is presented. Organization, capabilities and present status are discussed. Organizational aspects include executive, input, output, analysis and composite mechanics modules. Capabilities include: durability assessment of large structures and complex structural parts from composites, structural response due to static, cyclic, transient impact and thermal loads, and criteria for static, cyclic, and dynamic fracture. At the present state of development some of CODSTRAN's analysis capabilities include composite mechanics, static failures, and lamination residual stresses. An application in which CODSTRAN is used to predict the defect growth in a flat specimen, with a center through-slit under tension is studied. When completed, CODSTRAN will account for geometry and material nonlinearities, environmental effects as well as static, cyclic and dynamic fracture.

Chamis, C. C.↗

The effects of copper and titanium on silicon solar cells

Copper-doped N/P silicon solar cells fabricated from the Czochralski grown single-crystal wafers were found to have good electrical characteristics, but the titanium-doped N/P silicon solar cells has considerably lower conversion efficiency. However, in the copper/titanium-doped solar cells, copper seems to mitigate the unfavorable effects of titanium. To explain this behavior, microstructural tests were performed on silicon wafers and solar cells doped with copper, titanium and copper/titanium. Dark forward and reverse I-V measurements were performed on the solar cells to correlate the microstructural defects with the p-n junction properties. It was found that copper precipitates were formed in the copper-doped and copper/titanium-doped wafers and cells. There was a significant voltage drop in the dark reverse I-V measurements of the titanium solar cells. Also, there were some electronically active defects in the depletion region of some titanium-doped cells. Reasons that lead to the above results are given in detail.

Salama, A. M.↗

Radiation damage in lithium-counterdoped n/p silicon solar cells

Lithium counterdoped n+/p silicon solar cells were irradiated with 1 MV electrons and their post irradiation performance and low temperature annealing properties were compared to that of the 0.35 ohm cm control cells. Cells fabricated from float zone and Czochralski grown silicon were investigated. It was found that the float zone cells exhibited superior radiation resistance compared to the control cells, while no improvement was noted for the Czochralski grown cells. Room temperature and 60 C annealing studies were conducted. The annealing was found to be a combination of first and second order kinetics for short times. It was suggested that the principal annealing mechanism was migration of lithium to a radiation induced defect with subsequent neutralization of the defect by combination with lithium. The effects of base lithium gradient were investigated. It was found that cells with negative base lithium gradients exhibited poor radiation resistance and performance compared to those with positive or no lithium gradients; the latter being preferred for overall performance and radiation resistance.

Hermann, A. M.↗

Study of the influence of hole quality on composite materials

The influence of hole quality on the structural behavior of composite materials was investigated. From an industry survey it was determined that the most frequent imperfections encountered during hole fabrication are chipout, delamination, and oversize conditions. These hole flaw types were generated in critical areas of static, compression, and fatigue specimens fabricated from T300/5208 graphite/epoxy system. The specimens were tested in static and cyclic pin bearing modes in addition to compression loading. Results of these tests are presented and discussed. The hole chipout defect reduced the static and cyclic endurance characteristics. Oversize holes also lowered the cyclic pin bearing endurance, but had no influence of the static pin bearing characteristics. Delamination had no insignificant influence on the static tension and cyclic pin bearing characteristics. Compression tests demonstrated a deleterious effect for chipout of delamination defects. Hole quality requirements proposed are discussed.

Pengra, J. J.↗

Some characteristics of low-cost silicon sheet

The paper discusses structural defects in low-cost silicon sheets and their effect on the electronic properties related to solar cell performance. Experimental data are presented on the influence of grain boundaries on minority carrier diffusion length, impurity defect interaction, and variable surface recombination velocity. An analytical model of the effect of grain boundaries on solar cell performance is constructed based on these results.

Koliwad, K. M.↗

Wire-Wrap Chatter Detector

Monitoring circuit responds to changes in resistance as little as 0.1 ohm. Has been used to detect defective wire-wrap connections during thermal and vibration tests. Defect is indicated to operator by light-emitting diode and by increase in count on a two-digit display.

Fisch, G. Z.↗

Incipient Failure Detection (IFD) of antifriction ball bearings

Two methods were investigated for retrieving the ball bearing signals buried by the overall signature of an operating large engine such as the main space shuttle engine. The signal averaging method averages n** signals over a time duration equaling the known period of the ball bearing defect frequency. With this method, the desired ball bearing defect signal will be enhanced over the noise by a factor of the square root of n. A second method is to perform a further frequency analysis on the logarithmic spectrum in order to detect and separate different families of harmonics and sidebands, thereby giving information about modulating frequencies. These two alternate IFD methods were carried out with a Norland 3001 waveform and data system. The obtained results are then compared with the power spectral density (PSD) of the overall machine signals and conclusions are made accordingly.

Wang, D. Y.↗

Modeling of radiation damage in silicon solar cells

One MeV electron irradiation produces preponderantly isolated vacancy interstitial pairs. If neither of these defects is mobile, the concentration of each grows linearly with fluence. Annealing of damage depends on the nature of the damage. Vacancy interstitial pairs which are bound by an interaction such that they mutually annihilate rather than dissociate are termed close pairs; close pair recovery usually occurs at a lower temperature than the temperature at which long distance defect migration occurs. Annealing of the remaining frozen in damage occurs when a temperature is reached where the vacancy or interstitial is mobile; usually the interstitial is more mobile than the vacancy. The recovery occurs in two regimes which may be resoluable.

Oehrlein, G.↗

Radiation tolerance of boron doped dendritic web silicon solar cells

The potential of dendritic web silicon for giving radiation hard solar cells is compared with the float zone silicon material. Solar cells with n(+)-p-P(+) structure and approximately 15% (AMl) efficiency were subjected to 1 MeV electron irradiation. Radiation tolerance of web cell efficiency was found to be at least as good as that of the float zone silicon cell. A study of the annealing behavior of radiation-induced defects via deep level transient spectroscopy revealed that E sub v + 0.31 eV defect, attributed to boron-oxygen-vacancy complex, is responsible for the reverse annealing of the irradiated cells in the temperature range of 150 to 350 C.

Rohatgi, A.↗