Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Embedded I&C for Extreme Environments

This project uses embedded instrumentation and control (I&C) technologies to demonstrate potential performance gains of nuclear power plant components in extreme environments. Extreme environments include high temperature, radiation, high pressure, high vibration, and high EMI conditions. For extreme environments, performance gains arise from moment-to-moment sensing of local variables and immediate application of local feedback control. Planning for embedding I&C during early system design phases contrasts with the traditional, serial design approach that incorporates minimal I&C after mechanical and electrical design is complete. The demonstration application involves the development and control of a novel, proof-of-concept motor/pump design. The motor and pump combination operate within the fluid environment, eliminating the need for rotating seals. Actively controlled magnetic bearings also replace failure-prone mechanical contact bearings that typically suspend rotating components. Such as design has the potential to significantly enhance the reliability and life of the pumping system and would not be possible without embedded I&C.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Battery Electrolyte Design for Electric Vertical Takeoff and Landing (eVTOL) Platforms

Here, the development of robust and high-performance battery systems is crucial for the advancement of Electric Vertical Takeoff and Landing (eVTOL) vehicles for urban air mobility. This study evaluates the performance of different lithium-ion battery chemistries under Electric Vertical Takeoff and Landing (eVTOL) load profiles. The actual flight data coupled with physical models is used to create discharge profiles for testing on developed lithium-ion cells for eVTOLs. The performance of a standard liquid electrolyte (1.2 M LiPF 6 in EC:EMC), labeled Gen-2, is benchmarked and compared with a fast-charging electrolyte (1.2 M LiFSI in EC:EMC), labeled XFC. Cell analysis involves the use of various techniques, such as impedance spectroscopy, polarization curves, and capacity retention measurements. Capacity retention is stable for both systems over 500 cycles, but unique discharge capacity trends are observed for different mission segments. During the initial takeoff hover stages, Gen-2 electrolytes experience substantial voltage fade, while XFC electrolytes maintain consistent behavior. In general, the Gen-2 electrolyte demonstrated lower discharge overpotentials and higher decay during cycling compared to the XFC electrolyte. This work highlights the complexity of eVTOL battery behavior and provides insights into battery system design, contributing to the advancement of battery energy storage solutions for urban air mobility.

25 ENERGY STORAGE↗

Computational modeling of microalgal biofilm growth in heterogeneous rotating algal biofilm reactors (RABRs) for wastewater treatment

Rotating algal biofilm reactors (RABRs) are innovative systems designed to cultivate microalgae biofilms efficiently. In this paper, we have developed a novel mathematical model to accurately capture the growth dynamics of algae biofilms within RABR. By considering the spatial heterogeneity of the RABR, we introduce a PDE-based model that addresses the spatial variations across the substratum, enabling a more accurate simulation of biofilm growth in RABRs. The photosynthesis process is modeled through reactive kinetics, driving the growth of the algae biofilm. To analyze the system's behavior, we employ finite difference numerical methods to solve the complex PDE model. We then conduct extensive numerical simulations to understand algae biofilm growth in the RABR environment under various operational factors and environmental conditions. One primary focus in these simulations is to investigate the impact of various harvesting strategies, harvesting frequencies, light intensity, and light exposure on the overall biomass productivity of the algae biofilm. The numerical results provide valuable insights into optimizing algae biofilm growth and designing harvesting techniques in RABR systems. Our proposed novel mathematical model provides an effective platform for the theoretical investigation and design of RABRs for wastewater treatment.

09 BIOMASS FUELS↗

Subsidence Risk Mitigation in LLW Final Covers: A Case History - 18286

Typical waste packaging and disposal practices at low-level radioactive waste (LLW) disposal facilities, while adequate for safe transportation and facility operations, introduce significant subsidence risk for the facilities' final cover systems. Subsidence is often caused by the collapse of voids in the waste packaging and surrounding cover soils that eventually propagate to the ground surface. This subsidence could result in the loss of final cover system integrity, stormwater ponding, concentrated flow of surface water and/or gas, increased leachate generation, transport of contaminants from the landfill, and potential adverse chemical reactions within the waste mass. For new LLW facilities, steps can be taken to minimize the subsidence potential of newly placed waste. However, there is a significant inventory of existing disposal facilities (trenches, pits, shafts, vaults, etc.), tank farms, and historic, subsurface burial grounds that require final covers - all of which present real subsidence risks. Final covers for these existing LLW disposal sites can be engineered to mitigate these risks. A case history of a 60-acre LLW final cover system design and construction project illustrates an innovative approach to this problem that offers superior risk mitigation compared to typical final cover design practice. This approach combines engineering simulations of the projected final cover mechanical performance, specific probabilistic performance targets, and targeted cover system improvements to manage the subsidence risk in the final design. The result is a successful final cover project that meets the needs of the community, state and federal regulators, and facility owner. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Remote Sensor Design for Visual Recognition with Convolutional Neural Networks

While deep learning technologies for computer vision have developed rapidly since 2012, modeling of remote sensing systems has remained focused around human vision. In particular, remote sensing systems are usually constructed to optimize sensing cost-quality trade-offs with respect to human image interpretability. While some recent studies have explored remote sensing system design as a function of simple computer vision algorithm performance, there has been little work relating this design to the state-of-the-art in computer vision: deep learning with convolutional neural networks. We develop experimental systems to conduct this analysis, showing results with modern deep learning algorithms and recent overhead image data. Our results are compared to standard image quality measurements based on human visual perception, and we conclude not only that machine and human interpretability differ significantly, but that computer vision performance is largely self-consistent across a range of disparate conditions. This repository contains all the code required to replicate the results of our research paper, and the corresponding docker environment in which that code can be executed. All code is written in Python3 and utilizes the PyTorch library (v1.0) for neural network model training and evaluation. Jupyter notebooks are used to visualize images transformed with our code, in addition to plotting experimental results. We also include the specific parameter files used to execute our experiments, with the intent that these experiments can be replicated.

Zelinski, michaelE.↗

Effects of digital fringe projection operational parameters on detecting powder bed defects in additive manufacturing

Additive manufacturing is a technology transforming traditional production timelines. Specifically, metal additive manufacturing (MAM) has been increasingly adopted by a variety of industries, not only to prototype, but also to fulfill full production scale applications with much lower lead times. Like any maturing manufacturing technology, developments in verifying and validating processes are necessary to support continuous growth. Due to the complex nature of MAM, part quality and repeatability remain integral challenges that inhibit further adoption of MAM for critical component production. In this study, we present data taken from a developing in-process monitoring system designed to measure and detect powder bed defects (PBDs) in powder bed fusion MAM systems using surface height maps created with structured light illumination. We showcase the feasibility of the monitoring technique for in-process implementation by detecting streak PBDs with varying severities (height, width) created in a lab environment. We present results of powder bed measurements for varying experimental parameters of the structured light system such as illumination angle, illumination pattern, and number of illuminations. We also present an expression used to determine experimental height noise based on input parameters for PBD detection based on the instrument transfer function of the structured light monitoring system for arbitrary pixel intensity noise contributions. In conclusion, with the results of PBD detection across multiple experimental measurement parameters, we provide a best practices approach to in-process implementation of the monitoring system in powder bed fusion manufacturing.

36 MATERIALS SCIENCE↗

An ERCOT test system for market design studies

An open source test system is developed that permits the dynamic modeling of centrally-managed wholesale power markets operating over highvoltage transmission grids. In default mode, the test system models basic operations in the Electric Reliability Council of Texas (ERCOT): namely, centrally-managed day-ahead and real-time markets operating over successive days, with congestion handled by locational marginal pricing. These basic operational features characterize all seven U.S. energy regions organized as centrally-managed wholesale power markets. Modeled participants include dispatchable generators, load-serving entities, and non-dispatchable generation such as unrmed wind and solar power. Users can congure a broad variety of parameters to study basic market and grid features under alternative system conditions. Users can also easily extend the test system's Java/Python software classes to study modied or newly envisioned market and grid features. Finally, the test system is integrated with a high-level simulation framework that permits it to function as a software component within larger systems, such as multi-country systems or integrated transmission and distribution systems. Finally, detailed test cases with 8-bus and 200-bus transmission grids are reported to illustrate these test system capabilities.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Analyzer-based phase-contrast imaging system using a micro focus x-ray source

Here we describe a new in-laboratory analyzer based phase contrast-imaging (ABI) instrument using a conventional X-ray tube source (CXS) aimed at bio-medical imaging applications. Phase contrast-imaging allows visualization of soft tissue details usually obscured in conventional X-ray imaging. The ABI system design and major features are described in detail. The key advantage of the presented system, over the few existing CXS ABI systems, is that it does not require high precision components, i.e., CXS, X-ray detector, and electro-mechanical components. To overcome a main problem introduced by these components, identified as temperature stability, the system components are kept at a constant temperature inside of three enclosures, thus minimizing the electrical and mechanical thermal drifts. This is achieved by using thermoelectric (Peltier) cooling/heating modules that are easy to control precisely. For CXS we utilized a microfocus X-ray source with tungsten (W) anode material. In addition the proposed system eliminates tungsten's multiple spectral lines by selecting monochromator crystal size appropriately therefore eliminating need for the costly mismatched, two-crystal monochromator. The system imaging was fine-tuned for tungsten Kα{sub 1} line with the energy of 59.3 keV since it has been shown to be of great clinical significance by a number of researchers at synchrotron facilities. In this way a laboratory system that can be used for evaluating and quantifying tissue properties, initially explored at synchrotron facilities, would be of great interest to a larger research community. To demonstrate the imaging capability of our instrument we use a chicken thigh tissue sample.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Moisture ingress into electronics enclosures under isothermal conditions

The number of electronics used in outdoor environment is constantly growing. The humidity causes about 19 % of all electronics failures and, especially, moisture increases these problems due to the ongoing process of miniaturization and lower power consumption of electronic components. Moisture loads are still not understood well by design engineers, therefore this field has become one of the bottlenecks in the electronics system design. The objective of this paper is to model moisture ingress into an electronics enclosure under isothermal conditions. The moisture diffusion model is based on a 1D quasi-steady state (QSS) approximation for Fick’s second law. This QSS approach is also described with an electrical analogy which gives a fast tool in modelling of the moisture response. The same QSS method is applied to ambient water vapour variations. The obtained results are compared to an analytical solution and very good agreement is found.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The MIST-1 and MIST-2 multicusp ion sources for high-current $H$$^{+}_{2}$ beams

We present two iterations of the Multicusp Ion Source Technology at MIT (MIST) sources, designed to fulfill the requirements of the HCHC-XX cyclotron design. The HCHC-XX is a novel compact cyclotron accelerating $H$$^{+}_{2}$. Beam is injected through a radio-frequency quadrupole buncher-accelerator (embedded in the cyclotron yoke) and utilizes so-called vortex motion during acceleration. If successful, it will deliver 10 mA of protons at 60 MeV in CW mode. This scheme requires a low-emittance, high-current initial beam with high $H$$^{+}_{2}$ purity. We briefly summarize the design and previous results of the MIST-1 ion source and, for the first time, the detailed design of the new and improved MIST-2, including the mechanical, electrical, and control system design. We further show experimental results of using the MIST-2 backplate on the MIST-1 body, present a study using different types of permanent magnets for confinement (including no magnets), and finally, we present first results of the MIST-2 in full operation. In this first commissioning run, we were able to increase the total extracted current from the MIST-2 to 7 mA—a factor of 2 over the MIST-1.

Winklehner, D. [Massachusetts Institute of Technol↗

Robotic sample changers for macromolecular X-ray crystallography and biological small-angle X-ray scattering at the National Synchrotron Light Source II

In this work, we present two robotic sample changers integrated into the experimental stations for the macromolecular crystallography (MX) beamlines AMX and FMX, and the biological small-angle scattering (bioSAXS) beamline LiX. They enable fully automated unattended data collection and remote access to the beamlines. The system designs incorporate high-throughput, versatility, high-capacity, resource sharing and robustness. All systems are centered around a six-axis industrial robotic arm coupled with a force torque sensor and in-house end effectors (grippers). They have the same software architecture and the facility standard EPICS-based BEAST alarm system. The MX system is compatible with SPINE bases and Unipucks. It comprises a liquid nitrogen dewar holding 384 samples (24 Unipucks) and a stay-cold gripper, and utilizes machine vision software to track the sample during operations and to calculate the final mount position on the goniometer. The bioSAXS system has an in-house engineered sample storage unit that can hold up to 360 samples (20 sample holders) which keeps samples at a user-set temperature (277 K to 300 K). The MX systems were deployed in early 2017 and the bioSAXS system in early 2019.

36 MATERIALS SCIENCE↗

A Multi-objective Microgrid Assessment and Sizing Framework for Economic and Resilience Benefits

This paper presents an innovative multi-objective assessment and sizing framework for battery energy storage system paired with photovoltaics for a cost-effective and resilient microgrid. In the proposed framework, we simultaneously consider i) economic benefits from bundling grid services in grid-connected mode and ii) enhanced resilience by operating the microgrid in island mode upon outages of the main grid. Instead of simply treating resilience as another monetary value stream, this paper models resilience and economic benefits as two separate objectives. Multi-objective optimization is developed to explore different sizing and dispatch options and generate the Pareto front to assist decision-making in system design. Case studies on a real-world microgrid project in Puget Sound Energy system are presented to illustrate the proposed modeling and sizing methods.

Battery energy storage, Microgrid, Optimal Sizingp↗

Sage: parallel semi-asymmtric graph algorithms for NVRAMs

Non-volatile main memory (NVRAM) technologies provide an attractive set of features for large-scale graph analytics, including byte-addressability, low idle power, and improved memory-density. NVRAM systems today have an order of magnitude more NVRAM than traditional memory (DRAM). NVRAM systems could therefore potentially allow very large graph problems to be solved on a single machine, at a modest cost. However, a significant challenge in achieving high performance is in accounting for the fact that NVRAM writes can be much more expensive than NVRAM reads. In this paper, we propose an approach to parallel graph analytics using the Parallel Semi-Asymmetric Model (PSAM), in which the graph is stored as a read-only data structure (in NVRAM), and the amount of mutable memory is kept proportional to the number of vertices. Similar to the popular semi-external and semi-streaming models for graph analytics, the PSAM approach assumes that the vertices of the graph fit in a fast read-write memory (DRAM), but the edges do not. In NVRAM systems, our approach eliminates writes to the NVRAM, among other benefits. To experimentally study this new setting, we develop Sage, a parallel semi-asymmetric graph engine with which we implement provably-efficient (and often work-optimal) PSAM algorithms for over a dozen fundamental graph problems. We experimentally study Sage using a 48--core machine on the largest publicly-available real-world graph (the Hyperlink Web graph with over 3.5 billion vertices and 128 billion edges) equipped with Optane DC Persistent Memory, and show that Sage outperforms the fastest prior systems designed for NVRAM. Importantly, we also show that Sage nearly matches the fastest prior systems running solely in DRAM, by effectively hiding the costs of repeatedly accessing NVRAM versus DRAM.

97 MATHEMATICS AND COMPUTING↗

Productive Use of Energy in African Micro-Grids: Technical and Business Considerations

Demand for electricity from small industry and businesses, which is defined as the productive use of energy (PUE), is a key success factor for micro-grids. Because of the typically low energy usage of residential customers, without linkage to and support for these energy users, micro-grids are likely to struggle to reach the critical revenue needed for financial viability. This report is a resource entrepreneurs and developers can use to understand the technical and business model challenges related to PUE in smaller micro-grids. It focuses on small agricultural processing, and small industrial and commercial loads. This report examines best practices for promoting PUE and the business models used by developers. It starts with background information and a literature review followed by a discussion of key enterprise considerations for productive use (PU) including: value chain and business case analysis, enterprise development and training, appliance financing, and developers running PU businesses. Unlike many other reports on PUE, this report is based on application specific data. The report is also unique in that it provides actual customer demographics and load profiles. This report considers PUE from both business and technical perspectives, and it considers the interests of both the micro-grid operators and the microenterprises and entrepreneurs they serve. It looks at the service levels required by different PUs and the technical characteristics and challenges of different types of PU equipment. The report also includes examples of business cases for some of the most important PU opportunities, including milling, ice making, carpentry, egg incubation, and water treatment. This report is a resource that entrepreneurs, governments, and non-governmental organizations can use to help design programs to meet their individual goals of PUE in micro-grids and economic development in rural Africa. It can also be used by developers, engineers, and other organizations designing micro-grids to inform their technical and business decisions and to improve system design, reduce risk, and increase success with adding PU loads to both new and existing micro-grids.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Glass Formulation and Testing with RPP-WTP HLW Simulants (Final Report)

This report presents the results from HLW glass formulation work that was conducted at the Vitreous State Laboratory of The Catholic University of America during Part B1 of the RPP-WTP Project (formally known as TWRS-P) in support of the Privatization contractor, BNFL, Inc. Glass formulation development is required to provide data that are essential for design of the vitrification facility in the near term and for safe and reliable operation of that facility in the longer-term. These data also form the bases from which contractually and technically acceptable immobilized high-level waste (IHLW) products will be devised. Glass formulation therefore impacts many aspects of the vitrification facility design, overall process economics, and contractual compliance. As an integral part of the overall system design, development of glass formulations requires input from many sources including tank waste characterization, pretreatment process definition, flow sheet development, and processing schedules. Accordingly, the glass formulation effort must be responsive to new information as the facility design basis evolves.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Design and Performance Considerations for the Quantitative Measurement of HEU Residues Resulting from 99Mo Production

Molybdenum-99 is produced by the irradiation of high-enriched uranium (HEU) resulting in the accumulation of large quantities of HEU residues. In general, these residues are not recycled but are either disposed of or stored in containers with surface exposure rates as high as 100 R/h. The 235U content of these waste containers must be quantified for both accountability and waste disposal purposes. The challenges of quantifying such difficult-to-assay materials are discussed, along with performance estimates for each of several potential assay options. In particular, the design and performance of a High Activity Active Well Coincidence Counting (HA-AWCC) system designed and built specifically for these irradiated HEU waste materials are presented.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Feedstock and Catalyst Impact on Bio-Oil Production and FCC Co-Processing to Fuels

NREL’s thermochemical biomass conversion research is focused on ex-situ upgrading of biomass fast-pyrolysis (FP) vapors as an efficient and economical route to completely biogenic pyrolysis-based fuel precursors, potential fuels, and value-added chemicals depending on catalyst choice and process conditions. In this approach, biomass vapors are generated via fast pyrolysis with destabilizing vapor components (char, inorganics, tar aerosols) removed by hot gas filtration to produce conditioned vapors more responsive to catalytic upgrading. A Davison Circulating Riser (DCR), a petroleum industry standard for fluidized catalytic cracking (FCC) catalyst evaluation, was coupled with a custom pyrolyzer system designed to produce consistent composition pyrolysis vapors as feed to the DCR. The coupled system is shown below (Figure 1). Pyrolysis vapors, derived from pure hardwood and softwood, were upgraded using commercially available and laboratory modified zeolite-based catalysts. Upgraded oils were analyzed via 31P and 13C NMR spectroscopy, GCxGC-TOF/MS, carbonyl and ultimate analysis (CHNO), and micro distillation to assess both oil chemistry and distillation behavior as they relate to catalyst and feedstock type for producing fungible hydrocarbon product liquids. Measured process parameters identified from technoeconomic process analysis included achieving oil oxygenate contents of 20% or less, carbon-conversion efficiencies of 30% or more, and catalyst coking rates of 10% or less. A proprietary modified zeolite catalyst from Johnson Matthey produced oils that met these requirements. Using the DCR equipped with a proprietary nozzle system, a second approach focused on reducing the carbon intensity of petroleum-derived hydrocarbon fuels by FCC co-processing these CFP oils with petroleum vacuum gas oil (VGO) to produce biogenic carbon containing fuels. The vapor-phase upgrading results demonstrated for the first time the feasibility of producing refinery-compatible hydrocarbon fuel intermediates entirely from biomass-derived fast-pyrolysis vapors using an industry-accepted DCR system for catalytic upgrading. The co-processing results demonstrated the feasibility of using CFP oils with VGO feeds in FCC refinery operations to produce biogenic carbon containing fuels.

bio-oil↗

Uncertainty quantification of few group diffusion theory constants generated by the B1 theory-augmented Monte Carlo method

The purpose of this paper is to quantify uncertainties of fuel pin cell or fuel assembly (FA) homogenized few group diffusion theory constants generated from the B1 theory-augmented Monte Carlo (MC) method. A mathematical formulation of the first kind is presented to quantify uncertainties of the few group constants in terms of the two major sources of the MC method; statistical and nuclear cross section and nuclide number density input data uncertainties. The formulation is incorporated into the Seoul National Univ. MC code McCARD. It is then used to compute the uncertainties of the burnup-dependent homogenized two group constants of a low-enriched UO{sub 2} fuel pin cell and a PWR FA on the condition that nuclear cross section input data of U-235 and U-238 from JENDL 3.3 library and nuclide number densities from the solution to fuel depletion equations have uncertainties. The contribution of the MC input data uncertainties to the uncertainties of the two group constants of the two fuel systems is separated from that of the statistical uncertainties. The utilities of uncertainty quantifications are then discussed from the standpoints of safety analysis of existing power reactors, development of new fuel or reactor system design, and improvement of covariance files of the evaluated nuclear data libraries. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗