Search NASA⌕ Search

SEARCH · Search NASA

Results for “EVAPORATION MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

A study of remote sensing as applied to regional and small watersheds. Volume 2: Supporting technical details

The Stanford Watershed Model, the Kentucky Watershed Model and OPSET program, and the NASA-IBM system for simulation and analysis of watersheds are described in terms of their applications to the study of remote sensing of water resources. Specific calibration processes and input and output parameters that are instrumental in the simulations are explained for the following kinds of data: (1) hourly precipitation data; (2) daily discharge data; (3) flood hydrographs; (4) temperature and evaporation data; and (5) snowmelt data arrays. The Sensitivity Analysis Task, which provides a method for evaluation of any of the separate simulation runs in the form of performance indices, is also reported. The method is defined and a summary of results is given which indicates the values obtained in the simulation runs performed for Town Creek, Alabama; Alamosa Creek, Colorado; and Pearl River, Louisiana. The results are shown in tabular and plot graph form. For Vol. 1, see N74-27813.

Source record↗

A model of carbon production in a cometary coma

A model of the cometary ionosphere is developed in order to account for the large population of metastable C(D-1) atoms detected via the ultraviolet spectrum of Comet West (1976 VI). Dissociative recombination of CO(plus) ions and electrons is shown to be the dominant source of carbon atoms rather than photodissociation of CO so that the derived carbon production rate is only a lower limit to the evaporation rate of the carbon bearing mother molecule.

Feldman, P. D.↗

Sublimation and transport of water from the north residual polar cap on Mars

The possible role of the north residual cap in the current Martian water cycle was examined using models to assess the ability of the cap to supply water to the atmosphere and the ability of the atmospheric circulation to transport it out of the polar regions to low northern latitudes. Results indicate that rather extreme circumstances would be required for the cap to provide all of the observed increase in atmospheric water, such as a combination of high surface winds, low cap emissivities, or substantial evaporation from dark material. But even if these conditions could be met, the high-latitude circulation is too localized in scale to move much water vapor out of the polar environment. Both the present calculations and the data from the Viking's Mars Atmospheric Water Detection Experiment show that about two thirds of the water appearing in the Martian northern hemisphere during summer must be supplied by other sources. It is suggested that the additional source is water desorbing from the nonpolar regolith.

Haberle, Robert M.↗

Direct numerical simulation of a combusting droplet with convection

The evaporation and combustion of a single droplet under forced and natural convection was studied numerically from first principles using a numerical scheme that solves the time-dependent multiphase and multispecies Navier-Stokes equations and tracks the sharp gas-liquid interface cutting across an arbitrary Eulerian grid. The flow fields both inside and outside of the droplet are resolved in a unified fashion. Additional governing equations model the interphase mass, energy, and momentum exchange. Test cases involving iso-octane, n-hexane, and n-propanol droplets show reasonable comparison rate, and flame stand-off distance. The partially validated code is, thus, readied to be applied to more demanding droplet combustion situations where substantial drop deformation render classical models inadequate.

Liang, Pak-Yan↗

Computational fluid dynamics combustion analysis evaluation

This study involves the development of numerical modelling in spray combustion. These modelling efforts are mainly motivated to improve the computational efficiency in the stochastic particle tracking method as well as to incorporate the physical submodels of turbulence, combustion, vaporization, and dense spray effects. The present mathematical formulation and numerical methodologies can be casted in any time-marching pressure correction methodologies (PCM) such as FDNS code and MAST code. A sequence of validation cases involving steady burning sprays and transient evaporating sprays will be included.

Kim, Y. M.↗

Gravity Effects in Two-Phase Microgap Flow

The high power density of emerging electronic devices is driving the transition from remote cooling, which relies on conduction and spreading, to embedded cooling, which extracts dissipated heat on-site. Two-phase microgap coolers employ the forced flow of dielectric fluids undergoing phase change in a heated channel within or between devices. Such coolers must work reliably in all orientations for a variety of applications (e.g., vehicle-based equipment), as well as in microgravity and high-g for aerospace applications, but the lack of acceptable models and correlations for orientation- and gravity-independent operation has limited their use. Reliable criteria for achieving orientation- and gravity-independent flow boiling would enable emerging systems to exploit this thermal management technique and streamline the technology development process. As a first step toward understanding the effect of gravity in two-phase microgap flow and transport, in an earlier effort, the authors studied the effects of evaporator orientation, mass flux, and heat flux on flow boiling of HFE7100 in a 1.01 mm tall by 13.0 mm wide by 12.7 mm long microgap channel. Orientation-independence, defined as achieving similar critical heat fluxes, heat transfer coefficients, and flow regimes across orientations, was achieved for mass fluxes of 400 kg/sq.m-s and greater (corresponding to a Froude number of about 0.8). In the present effort, the authors have studied the effects of gravity, mass flux, and subcooling on flow boiling of HFE7100 in a 0.17 mm tall by 13.0 mm wide by 12.7 mm long microgap channel. The Flow Boiling in Microgap Coolers payload experienced about three minutes of weightlessness and shorter periods of high-g (up to about 5 g) during two recent flights aboard the Blue Origin New Shepard reusable launch vehicle. The results from the flight experiments will be presented and compared with published criteria for achieving gravity-independence.

Robinson, Franklin L.↗

An outgassing model of non-metallic materials for the ascent of a Titan 4 launch vehicle

Outgassing of nonmetallic materials and components inside Titan IV's 2A compartment during ascent may present a problem to the payload community in relation to molecular deposition and degradation of sensitive payload surfaces. The procedure currently being developed to model the amounts, transport, and deposition of outgassed molecular contaminants onto a payload's sensitive surface consists of three phases. The first phase involves the development of a thermogravimetric method that recreates the increasing temperature and decreasing pressure profiles expected in the 2A compartment of the TIV launch vehicle during ascent. The second phase involves the determination of deposition rates of outgassed materials onto a payload surface, and the subsequent evaporation rate as a function of temperature of deposited material. The third phase takes the temperature and pressure profiles from phase one, the deposition and evaporation rates and kinetic coefficients determined in phase two, and incorporates them into the SPACE II computer program to determine which payload surfaces are most susceptible to molecular deposition from TIV's outgassing sources, and the level of permanent deposition expected on those surfaces.

Barrows, R. D.↗

High heat flux single phase heat exchanger

This paper presents the results obtained to date in a program to develop a high heat flux, single-phase heat exchanger for spacecraft thermal management. The intended application is a net generation interface heat exchanger to couple the crew module water thermal bus to the two-phase ammonia main thermal bus in the Space Station Freedom. The large size of the interface heat exchanger is dictated by the relatively poor water-side heat transfer characteristics. The objective of this program is to develop a single-phase heat transfer approach which can achieve heat fluxes and heat transfer coefficients comparable to those of the evaporation ammonia side. A new heat exchanger concept has been developed to meet these objecties. The main feature of this heat exchanger is that it can achieve very high heat fluxes with a pressure drop one to two orders of magnitude lower than those of previous microchannel or jet impingement high heat flux heat exchangers. This paper describes proof-of-concept experiments performed in air and water and presents analytical model of the heat exchanger.

Valenzuela, Javier A.↗

Cooling of solar flares plasmas. 1: Theoretical considerations

Theoretical models of the cooling of flare plasma are reexamined. By assuming that the cooling occurs in two separate phase where conduction and radiation, respectively, dominate, a simple analytic formula for the cooling time of a flare plasma is derived. Unlike earlier order-of-magnitude scalings, this result accounts for the effect of the evolution of the loop plasma parameters on the cooling time. When the conductive cooling leads to an 'evaporation' of chromospheric material, the cooling time scales L(exp 5/6)/p(exp 1/6), where the coronal phase (defined as the time maximum temperature). When the conductive cooling is static, the cooling time scales as L(exp 3/4)n(exp 1/4). In deriving these results, use was made of an important scaling law (T proportional to n(exp 2)) during the radiative cooling phase that was forst noted in one-dimensional hydrodynamic numerical simulations (Serio et al. 1991; Jakimiec et al. 1992). Our own simulations show that this result is restricted to approximately the radiative loss function of Rosner, Tucker, & Vaiana (1978). for different radiative loss functions, other scaling result, with T and n scaling almost linearly when the radiative loss falls off as T(exp -2). It is shown that these scaling laws are part of a class of analytic solutions developed by Antiocos (1980).

Cargill, Peter J.↗

Using In-Situ Deposition of Metallic Thin Films on Mars to Monitor Atmospheric H20

We describe the use of a novel sensor, designed to characterize the reactive nature of the Martian atmosphere, to also characterize the instantaneous abundance of atmospheric H,O. The sensor deposits, in situ, a thin silver film onto a sapphire substrate and monitors oxidation by measuring resistance of the Ag film during both deposition and subsequent oxidation [1,2]. . The evaporation source is placed in the center of a hollow, open-ended tube. On flash heating the source, evaporated metallic silver rapidly reacts with oxidizing gases in the tube, depositing on the tube walls as a resisitive Ag oxide film. Unoxidized silver deposits over the Ag oxides, once the oxidizing gases in the vicinity of the source have been consumed. Since the ends of the tube are open, atmospheric gases in the tube cause a time delay as the evaporated silver initially reacts with the available O2, and H2O; once oxidizing gases in the tube are significantly depleted, a silver film closes the chemiresistor circuit. In principle this operation mode provides a repeatable measure of the variable H2O abundance, since O2, levels are constant in the atmosphere. To explore the utility of the instrument as an H2O sensor, predict its behavior, and identify possible failure modes, we developed a numerical model of the instrument, and exercised it for Mars conditions. The model predicts the behavior of the electrical circuit, the temperature dependence of resistivity for each component, and the resultant Joule heating. The model balances Joule heating against radiation, sensible heat loss to ambient CO2, and, latent heat loss from sublimating Ag. The flux of Ag atoms from the source is tracked continuously. In the gas phase, the number density of Ag, O2, and H2O is calculated, along with their reaction rates on collision. The model suggests that Ag substantially depletes H2O only near the center of the tube. The model supports the hypothesis that the onset of high conductivity between the A u electrodes is a function of the H2O abundance in the ambient gas, but only to a limit; when H2O abundances are buffered at or above 240K (an H2O abundance that would not have occurred on Mars), metallic Ag never deposits in excess of Ago, and the circuit does not close. A significant difference in the Mars simulation is that the Ag source sublimates more quickly, primarily because of differences in sensible heat fluxes from the source. This allows subsequent heating of the W filament used to support the Ag source. Had the originally-designed experimental sequence been carried out on Mars, the filament might have melted, making subsequent investigations impossible.

Zent, A. P.↗

Space Evaporator Absorber Radiator (SEAR) for Thermal Storage on Manned Spacecraft

Future manned exploration spacecraft will need to operate in challenging thermal environments. State-of-the-art technology for active thermal control relies on sublimating water ice and venting the vapor overboard in very hot environments, and or heavy phase change material heat exchangers for thermal storage. These approaches can lead to large loss of water and a significant mass penalties for the spacecraft. This paper describes an innovative thermal control system that uses a Space Evaporator Absorber Radiator (SEAR) to control spacecraft temperatures in highly variable environments without venting water. SEAR uses heat pumping and energy storage by LiCl/water absorption to enable effective cooling during hot periods and regeneration during cool periods. The LiCl absorber technology has the potential to absorb over 800 kJ per kg of system mass, compared to phase change heat sink systems that typically achieve approx. 50 kJ/kg. This paper describes analysis models to predict performance and optimize the size of the SEAR system, estimated size and mass of key components, and an assessment of potential mass savings compared with alternative thermal management approaches. We also describe a concept design for an ISS test package to demonstrate operation of a subscale system in zero gravity.

Izenson, Michael G.↗

Possible Impacts of Snow Darkening Effects on the Hydrological Cycle over Western Eurasia and East Asia

In this paper, we investigated the possible impact of snow darkening effect (SDE) by light-absorbing aerosols on the regional changes of the hydrological cycle over Eurasia using the NASA GEOS-5 Model with aerosol tracers and a state-of-the-art snow darkening module, the Goddard SnoW Impurity Module (GOSWIM) for the land surface. Two sets of ten-member ensemble experiments for 10 years were carried out forced by prescribed sea surface temperature (2002–2011) with different atmospheric initial conditions, with and without SDE, respectively. Results show that SDE can exert a significant regional influence in partitioning the contributions of evaporative and advective processes on the hydrological cycle, during spring and summer season. Over western Eurasia, SDE-induced rainfall increase during early spring can be largely explained by the increased evaporation from snowmelt. Rainfall, however, decreases in early summer due to the reduced evaporation as well as moisture divergence and atmospheric subsidence associated with the development of an anomalous mid- to upper-tropospheric anticyclonic circulation. On the other hand, in the East Asian monsoon region, moisture advection from the adjacent ocean is a main contributor to rainfall increase in the melting season. A warmer land-surface caused by earlier snowmelt and subsequent drying further increases moisture transport and convergence significantly enhancing rainfall over the region. Our findings suggest that the SDE may play an important role in leading to hotter and drier summers over western Eurasia, through coupled land-atmosphere interaction, while enhancing East Asian summer monsoonal precipitation via enhanced land-ocean thermal contrast and moisture transport due to the SDE-induced warmer Eurasian continent.

snow darkening effect↗

Albedo asymmetry of Iapetus

Observational data for Iapetus and other Saturn moons are used to show that the dark areas on Iapetus feature organic chromophores caused by UV irradiation of CH4-rich ice. The Iapetus albedo pattern, brighter at the poles and in the trailing hemisphere, is suggested to originate from ballistic impact redistribution of surface material in terms of an impact flux gradient. The orange/violet color ratios from Voyager imagery were measured as 1.46 for the leading hemisphere and 1.24 for the trailing hemisphere. The evolution of the Iapetus regolith during processes of ice evaporation, impact ablation, material transport, and chemical alteration is discussed for factors causing the albedo asymmetry. Comparisons of surface features of Titan, Oberon,, and Hyperion with those of Iapetus indicate a balance may exist between UV photochemistry and ablation on Iapetus, with the impact gradient having been determined by the tidally locked revolution of the moon. Voyager 2 data on the uranian moons are expected to offer confirmation or denial of the model.

Squyres, S. W.↗

Mathematical modeling and analysis of heat pipe start-up from the frozen state

The start-up process of a frozen heat pipe is described and a complete mathematical model for the start-up of the frozen heat pipe is developed based on the existing experimental data, which is simplified and solved numerically. The two-dimensional transient model for the wall and wick is coupled with the one-dimensional transient model for the vapor flow when vaporization and condensation occur at the interface. A parametric study is performed to examine the effect of the boundary specification at the surface of the outer wall on the successful start-up from the frozen state. For successful start-up, the boundary specification at the outer wall surface must melt the working substance in the condenser before dry-out takes place in the evaporator.

Jang, Jong Hoon↗

Mathematical modeling and analysis of heat pipe start-up from the frozen state

The start-up process of a frozen heat pipe is described and a complete mathematical model for the start-up of the frozen heat pipe is developed based on the existing experimental data, which is simplified and solved numerically. The two-dimensional transient model for the wall and wick is coupled with the one-dimensional transient model for the vapor flow when vaporization and condensation occur at the interface. A parametric study is performed to examine the effect of the boundary specification at the surface of the outer wall on the successful start-up from the frozen state. For successful start-up, the boundary specification at the outer wall surface must melt the working substance in the condenser before dry-out takes place in the evaporator.

Jang, J. H.↗

Formation of ions and radicals from icy grains in comets

Two theoretical models for the formation of radicals from ice grains are examined to determine if this can explain the jets in comets. It is shown that the production rates for these radicals by the photolysis of molecules in the icy grains are not high enough to explain the jets. A new mechanism is proposed involving the release of cations and anions in the gas phase as the icy mantle surrounding the grains is evaporated. Solar visible radiation can then form radicals by photodetachment of the electrons from these anions. The production rate of radicals formed in this manner is in accord with the production rates of the observed radicals.

Jackson, William M.↗

Preliminary SP-100/Stirling heat exchanger designs

Analytic modeling of several heat exchanger concepts to couple the SP-100 nuclear reactor primary lithium loop and the Space Stirling Power Convertor (SSPC) was performed. Four 25 kWe SSPC's are used to produce the required 100 kW of electrical power. This design work focused on the interface between a single SSPC and the primary lithium loop. Manifolding to separate and collect the four channel flow was not modeled. This work modeled two separate types of heat exchanger interfaces (conductive coupling and radiative coupling) to explore their relative advantages and disadvantages. The minimum mass design of the conductively coupled concepts was 18 kg or 0.73 kg/kWe for a single 25 kWe convertor. The minimum mass radiatively coupled concept was 41 kg or 1.64 kg/kWe. The direct conduction heat exchanger provides a lighter weight system because of its ability to operate the Stirling convertor evaporator at higher heat fluxes than those attainable by the radiatively coupled systems. Additionally the conductively coupled concepts had relatively small volumes and provide potentially simpler assembly. Their disadvantages were the tight tolerances and material joining problems associated with this refractory to superalloy interface. The advantages of the radiatively coupled designs were the minimal material interface problems.

Schmitz, Paul↗

Lunar and Planetary Science XXXVI, Part 10

The Problem of Incomplete Mixing of Interstellar Components in the Solar Nebula: Very High Precision Isotopic Measurements with Isoprobes P and T. Finally: Presolar Graphite Grains Identified in Orgueil. Basaltic Ring Structures as an Analog for Ring Features in Athabasca Valles, Mars. Experimental Studies of the Water Sorption Properties of Mars-Relevant Porous Minerals and Sulfates. Silicon Isotope Ratio Variations in CAI Evaporation Residues Measured by Laser Ablation Multicollector ICPMS. Crater Count Chronology and Timing of Ridged Plains Emplacement at Schiaparelli Basin, Mars. Martian Valley Networks and Associated Fluvial Features as Seen by the Mars Express High Resolution Stereo Camera (HRSC). Fast-Turnoff Transient Electromagnetic (TEM) Field Study at the Mars Analog Site of Rio Tinto, Spain. Time Domain Electromagnetics for Mapping Mineralized and Deep Groundwater in Mars Analog Environments. Mineralogical and Seismological Models of the Lunar Mantle. Photometric Observations of Soils and Rocks at the Mars Exploration Rover Landing Sites. Thermal Infrared Spectral Deconvolution of Experimentally Shocked Basaltic Rocks Using Experimentally Shocked Plagioclase Endmembers.

Source record↗