Search NASA⌕ Search

SEARCH · Search NASA

Results for “Intermittent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

SCILLA Secondary Aerosol Volume Concentration Airborne Data

This data set contains secondary aerosol volume concentration in cubic micrometers per cubic centimeter (um^3/cm^3). The aerosol was generated in an oxidation flow reactor (OFR) and its volume concentration measured with a scanning mobility particle sizer (SMPS). Both components were designed and built at the University of California Riverside. Ambient particles were removed with a Teflon filter upstream of the OFR and then pure ammonium sulfate particles were added to create a stable aerosol surface area on which low-volatility oxidation products condense. High concentrations of hydroxyl radical (OH) formed inside the OFR accelerate the oxidative chemistry that would typically occur over a period of several days in the atmosphere, resulting in the production of secondary aerosol from precursor gases present in the ambient air. Concentrations of added ozone and water vapor were controlled to produce the desired and approximately constant level of photochemical aging. The reactor temperature was controlled, while the pressure was not, and was always slightly lower than that of the sampled outside air. Sampled air was pulled from above the Naval Postgraduate School’s (NPS) Twin Otter aircraft through a rear-facing, ¼” OD PFA Teflon tube. The sample stream was split between the OFR and several gas analyzers (NOx, CO, O3, and H2O). Though not contained in these files, data from an aerosol mass spectrometer intermittently operated downstream of the OFR are also available.

{"secondary aerosol concentration",aerosol_concent↗
DOE OSTI2024

Design of a Meso-Scale Test of a Fracture Thermal Energy Storage (FTES) System

This paper will present the characterization, scaling, and design of an intermediate-scale field test of a fracture thermal energy storage system (FTES). Seasonal storage of thermal energy has the potential to both significantly reduce the total energy requirements for heating and cooling of buildings, but also allow for the flexibility to store thermal energy from intermittent sources. With approximately half of global energy consumption currently being used for heating and cooling, this represents an important path to reducing greenhouse gas (GHG) emissions. The concept of FTES is to drill two or more wells into a low permeability formation, generally at a depth of less than a few hundred meters, and then generate hydraulic fractures to create flow paths for water to circulate between the wells. Hot or cold thermal energy can then be stored in the surrounding rock mass by circulating hot or cold water through the fractures, which will heat or cool the rock mass. To recover the stored energy, ambient temperature water can be then circulated through the fractures, which will then be heated or cooled by the rock mass. Fractures inherently have a very large ratio of surface area to volume. This allows for very high heat fluxes to and from the rock mass to be achieved despite the relatively low thermal conductivity of most geologic formations. Because large fractures can be made with low-cost equipment and with only inexpensive and environmentally safe materials such as water and sand, the cost to construct even large FTES systems is expected to be quite low. This paper will present what the performance requirements, size, and operating conditions of a full-scale system to operate a commercial building. The paper will describe how these full-scale system characteristics will be used as a design basis for an intermediate-scale FTES test to be conducted at the Sanford Underground Research Facility (SURF) in Lead, SD.

Burghardt, Jeffrey A.↗
DOE OSTI2021

Alfven eigenmodes and fast ion transport in negative triangularity DIII-D plasmas

The first energetic particle experiments in negative triangularity tokamak plasmas have been carried out on DIII-D. Alfvén eigenmode (AE) activity and associated fast ion transport comparable to that in positive triangularity is observed during the current ramp portion of all plasmas with early beam heating indicating negative triangularity does not confer a special advantage with respect to AE induced transport. In these discharges, a range of mode activity driven by the sub-Alfvénic (Vbeam/VA < 0.5) 80 kV neutral beams is found including beta induced Alfvén acoustic eigenmodes, beta induced Alfvén eigenmodes, reversed shear Alfvén eigenmodes (RSAEs) and toroidicity induced Alfvén eigenmodes (TAEs). Mode intermittency and possibly chirping appears to be more common than comparable positive triangularity and/or oval discharges but overall, the unstable spectra and mode amplitudes observed on magnetics, CO2 interferometry, and electron cyclotron emission in a set of matched positive and negative triangularity cases at moderate beam power is similar. Large levels of Alfvén eigenmode induced fast ion transport are found in both positive and negative triangularity with up to 70% central fast ion pressure deficits relative to classical predictions early during the current ramp phase for discharges with 3 MW injected 80 kV neutral beam power. The deficit in both cases is reduced toward zero as the current penetrates and eventually reaches classical levels during current flattop with qmin ≈ 1. Fast ion transport in negative triangularity plasmas measured using a beam modulation technique show very similar levels to those measured in oval plasmas over the range of tested beam powers (Pbeam ≈ 2–7 MW). This similarity is found despite quite different unstable spectra in the highest beam power case where a mixture of coherent and quasi-coherent modes in the TAE frequency range are observed in negative triangularity and a spectrum of more typical narrowband TAEs and RSAEs is observed for the oval plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1966

Tooling concepts for assembly of large structures

Manufacture of the S-IC stage of the Saturn V space vehicle has resulted in new. concepts and innovations in the field of tooling. The structure size (35-ft diameter), the high reliability and accuracy requirements, and the low density or production quantity lead to a greater degree of simplicity, economy, and versatility in fabrication and assembly tooling. There are three specific concepts which should be applicable in industry, local jigging for welding, rotation of structures in vertical assemblies, and the assembly of two structures. The usual weld jigging serves a two-fold purpose: (a) to support the molten weld puddle and (b) to force and maintain alinement of the parts being welded. The extension of this method to large-diameter tanks is expensive and difficult. An alternate procedure used at MSFC is to perform free-state welding and use local jigging (stra1rclamps) and intermittent tack welding. Cylindrical structures can be accurately rotated for routing or welding on a simplified ring turntable. The tool consists of a ring of the structure diameter resting on rollers. Torque is nearly zero since the ring is rotated by friction rollers with the force being applied at the ring perimeter. Two such turntables are used at MSFC. The horizontal mating of two large components, where controlled motions of small magnitude are necessary, can be easily done by positioning units equipped with air-bearings. Such bearings are usable on concrete of minimum surface preparation and require no special air pressure source. This concept is used in assembly of the two S-IC containers.

Saturn S-IC stage↗
NASA NTRS1967

Eddy current disk valve

Quick-opening, intermittent flow valve requires a small amount of electrical energy to open and which closes by the restoring action of a rubber stop. This eddy current disk valve opens in less than 100 microseconds and takes only 10 joules of energy.

Larson, A. V.↗
NASA NTRS1968

Regulated dc-to-dc converter features low power drain

A regulated dc-to-dc converter requires negligible standby power for the operation of critical electronic equipment. The main operating circuitry consumes power intermittently according to load conditions, rather than constantly.

Thornwall, J.↗
NASA NTRS1969

Testing the flammability of materials exposed to arcs

Apparatus tests flammability and ignition characteristics of materials in close proximity to incandescent metal fragments or spalls ejected from intermittent short circuit arcs in air or oxygen rich atmospheres. It simulates a situation where an exposed live wire makes contact with a grounded member in areas containing organic matter.

Hamlett, B. J.↗
NASA NTRS1970

Pulse-rate averaging circuit

Averaging circuit provides a secondary control signal during inoperative periods of an intermittent primary control system. It can also provide an average pulse rate over a fixed time interval, such as in a digital frequency meter.

Jessee, R. D.↗
NASA NTRS1971

Apollo 14 composite casting demonstration

This program assisted in the design and implementation of the composite casting demonstration for the Apollo 14 mission. Both flight and control samples were evaluated. Some conclusions resulting from a comparison of the flight and control samples were: (1) Solidification in neither the flight nor control samples was truly directional. (2) Apparent intermittent contact of the melt with the container in the flight samples led to unusual nucleation and growth structures. (3) There was greater uniformity, on a macro scale, of both pores and structural features in the flight sample; presumably the result of the reduced gravity conditions. (4) It seems quite feasible to produce enhanced dispersions of gases and dense phases in a melt which is solidified in reduced gravity. (5) A two-stage heating/cooling cycle may help directional solidification. (6) Sample materials should be selected from materials in which the dispersant fully wets the matrix material. (7) Experiments should be conducted in two modes: (1) where the melt is in good thermal contact with the container, and (2) where the melt is in a free-float condition.

Source record↗
NASA NTRS1971

The structure of jet turbulence producing jet noise

The structure of the turbulence in the mixing region for the first few diameters downstream from the outlet of a circular subsonic jet is characterized at three Mach numbers, 0.3, 0.5, and 0.7, with most of the measurements taken at M = 0.3. Profiles of turbulence intensity showed that downstream of the lip intensity is independent of axial distance, while in the core intensity varies by a factor of eight between the jet outlet and the end of the core. A digital data reduction program was used to calculate the auto- and cross-correlations of axial velocity fluctuations and the power spectral densities. Convection velocities were measured using broadband, hot wire signals and signals that were digitally filtered for band-passes about center frequencies of 0.8, 1.3, 1.6, and 3.2 kHz. The center frequency of 1.3 kHz corresponded to the peak energy in the core spectrum. The results support the hypothesis that the coherent pressure field is driven by the intermittent fluctuations at the core boundary, which in turn are related to the large (low frequency) eddies.

Wooldridge, C. E.↗
NASA NTRS1972

Wind-tunnel simulation of store jettison with the aid of magnetic artificial gravity

A method employed in the simulation of jettison of stores from aircraft involving small scale wind-tunnel drop tests from a model of the parent aircraft is described. Proper scaling of such experiments generally dictates that the gravitational acceleration should ideally be a test variable. A method of introducing a controllable artificial component of gravity by magnetic means has been proposed. The use of a magnetic artificial gravity facility based upon this idea, in conjunction with small scale wind-tunnel drop tests, would improve the accuracy of simulation. A review of the scaling laws as they apply to the design of such a facility is presented. The design constraints involved in the integration of such a facility with a wind tunnel are defined. A detailed performance analysis procedure applicable to such a facility is developed. A practical magnet configuration is defined which is capable of controlling the strength and orientation of the magnetic artificial gravity field in the vertical plane, thereby allowing simulation of store jettison from a diving or climbing aircraft. The factors involved in the choice between continuous or intermittent operation of the facility, and the use of normal or superconducting magnets, are defined.

Stephens, T.↗
NASA NTRS1972

Seventeen Ketogenic steroids excretion in crewmen in a 90-day manned test of an advanced regenerative life support system

Seventeen KGS (17-Ketogenic steroids) and Na/K were determined in 19 urine specimens collected by each of 4 crewmen during the 90-day test. The specimens represented 10% aliquots of 24-hour collections stored frozen onboard the simulator until passthrough. Electrolytes were analyzed immediately after sample passthrough while the steroids were determined post-test on aliquots of the original sample held at 203 K. Steroid data was corrected for body weight and also for analytical variation in the laboratory urine pool control. Long-term nonspecific responses to low-level stress appear to be reflected by the individual and group mean 17-KGS excretion patterns. The first 39 and the last 20 days of the test were significantly different--and presumably more stressful to the crew--than the period from days 39 to 67. Reduction of adrenocortical function during the mid-test phase is attributed to either an adaptation to chronic or intermittent stress or was the result of an actual reduction in the operational demands of the test during this time. Most remarkable of the metabolic findings is the prevalance of high Na/K ratios and an abrupt peak on day 74 for all 4 crewmen.

Myers, D. J.↗
NASA NTRS1971

Cryogen acquisition in orbit

Orbital cryogen acquisition is a definite requirement for engine restart and/or propellant transfer on all major future missions. The most promising methods, especially for large scale vehicles, are acquisition by linear acceleration and acquisition by capillary systems. Intermittent acceleration and propellant settling requires some state-of-the-art extension since it has not been attempted on a large scale cryogen vehicle. Capillary acquisition systems offer the advantages of reusability, passiveness, low weight, and mission flexibility. The major disadvantage is that of an undeveloped technology. The method does not lend itself to verification through ground testing.

Hastings, L. J.↗