Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Characteristics at Mach Number of 2.03 of a Series of Wings Having Various Spanwise Distributions of Thickness Ratio and Chord

A series of semispan wing models having various spanwise distributions of both thickness ratio and chord but having the same effective thickness ratio was tested in the Langley 4-by 4-foot supersonic pressure tunnel at Mach number 2.03 and Reynolds numbers from 1.9 x 10(exp 6) to 6.5 x 10(exp 6) complex wing forms with thickened roots, extended root chords, and higher volumes show appreciably lower zero-lift wave drag coefficients than the plain swept wings. A calculative technique for the determination of wave drag has been applied to one of the complex wings of the series and good agreement is shown with experimental results. The complex wing forms showed higher drags due to lift than the plain swept wings.

Robins, A. Warner↗

Maximum likelihood estimates of lift and drag characteristics obtained from dynamic aircraft maneuvers

A maximum likelihood estimation method for obtaining lift and drag characteristics from dynamic flight maneuvers was investigated. This paper describes the method and compares the estimates of lift and drag obtained by using the method with estimates obtained from wind-tunnel tests and from established methods for obtaining estimates from flight data. In general, the lift and drag coefficients extracted from dynamic flight maneuvers by the maximum likelihood estimation technique are in good agreement with the estimates obtained from the wind-tunnel tests and the other methods. When maneuvers that met the requirements of both flight methods were analyzed, the results of each method were nearly the same. The maximum likelihood estimation technique showed promise in terms of estimating lift and drag characteristics from dynamic flight maneuvers. Further studies should be made to assess the best mathematical model and the most desirable type of dynamic maneuver to get the highest quality results from this technique.

Iliff, K. W.↗

Investigation in the Ames Supersonic Free-Flight Wind Tunnel of the Static Longitudinal Stability of the Hermes A-3B Missile at a Mach Number of 5.0

Models of the Hermes A-3B missile were tested in the Ames supersonic free-flight wind tunnel to determine the static-longitudinal-stability characteristics at a Mach number of 5.0 and a Reynolds number based on body length of 10 million. The results indicated that the model center of pressure was 45.3 percent of the body length aft of the nose and the lift-curve slope based on body frontal area was 0.064 per degree. Estimates indicated that the effect on these characteristics of aeroelastic twisting of the model fins was small but important if a precise location of center of pressure is required. A comparison of the test results with predictions based on available theory showed that the theory was useful only for rough estimates, The drag coefficient at zero lift, based on body frontal area, was found to be 0.155.

Denardo, Billy Pat↗

Calculation of the longitudinal aerodynamic characteristics of wing-flap configurations with externally blown flaps

A theoretical investigation was carried out to extend and improve an existing method for predicting the longitudinal characteristics of wing flap configurations with externally blown flaps (EBF). Two potential flow models were incorporated into the prediction method: a wing and flap lifting-surface model and a turbofan engine wake model. The wing-flap model uses a vortex-lattice approach to represent the wing and flaps. The jet wake model consists of a series of closely spaced vortex rings normal to a centerline which may have vertical and lateral curvature to conform to the local flow field beneath the wing and flaps. Comparisons of measured and predicted pressure distributions, span load distributions on each lifting surface, and total lift and pitching moment coefficients on swept and unswept EBF configurations are included. A wide range of thrust coefficients and flap deflection angles is considered at angles of attack up to the onset of stall. Results indicate that overall lift and pitching-moment coefficients are predicted reasonably well over the entire range. The predicted detailed load distributions are qualitatively correct and show the peaked loads at the jet impingement points, but the widths and heights of the load peaks are not consistently predicted.

Mendenhall, M. R.↗

Fortified LEWICE with viscous effects

A method for computing the prediction of ice shapes on airfoils and their effects on the airfoil lift and drag coefficients are described. The previously developed LEWICE code has been modified to avoid problems due to multiple stagnation points. The interactive boundary-layer method developed by Cebeci has been incorporated into LEWICE to improve the accuracy of predicting ice shapes as well as to compute the performance characteristics of iced airfoils. The paper also presents ice shapes calculated without and with viscous effects, the consequences for aerodynamic properties, particulary lift and drag, and evaluation of the time steps used in the ice accretion process.

Cebeci, Tuncer↗

A Transonic Wind-Tunnel Investigation of the Longitudinal Aerodynamic Characteristics of a Model of the Lockheed XF-104 Airplane

The transonic longitudinal aerodynamic characteristics of a 0.0858-scale model of the Lockheed XF-104 airplane have been obtained from tests at the Langley 16-foot transonic tunnel. The results of the investigation provide some general information applicable to the transonic properties of thin, low-aspect-ratio, unswept wing configurations utilizing a high horizontal tail . The model employs a horizontal tail mounted at the top of the vertical tail and a wing with an aspect ratio of 2.5, a taper ratio of 0.385, and 3.4-percent-thick airfoil sections. The lift, drag, and static longitudinal pitching moment were measured at Mach numbers from 0.80 t o 1.09 and angles of attack from -2.5 deg to 22.5 deg. Some of the dynamic longitudinal stability properties of the airplane have been predicted from the test results. In addition, some visual flow studies on the wing surfaces obtained at Mach numbers of 0.80 and 1.00 are included. Results of the investigation show that the transonic rise in drag coefficient at zero lift is about 0.030. At high angles of attack, the model becomes longitudinally unstable at Mach numbers from 0.80 t o 0.90, whereas a reduction in static stability is experienced when very high angles of attack are reached at Mach numbers above 0.90. Longitudinal dynamic stability calculations show that the longitudinal control is good at angles of attack below the unstable break in the static pitching-moment curves, but a typical corrective control applied after the occurrence of neutral stability has little effect in averting pitch-up.

Hieser, Gerald↗

Transition Prediction for the 30P30N Airfoil and the CRM-HL using FUN3D

The ability to accurately model transition over high-lift configurations can lead to improved agreement between stationary Reynolds-Averaged Navier-Stokes (RANS) computations and experimental measurements. In this work, selected transport-equation-based RANS models for transition prediction in the NASA FUN3D flow solver are used to simulate flow over the 30P30N three-element airfoil and the High-Lift Common Research Model (CRM-HL). The primary RANS-based transition model is the Langtry-Menter (LM) 𝜸-Re𝜽𝒕 model coupled with the Menter shear-stress transport model. Additionally, the existing capability for transition prediction based on linear stability correlations is used to allow the modeling of transition over multiple elements of the 30P30N configuration. This approach pairs an algebraic transition model with the Spalart-Allmaras (SA) turbulence model that relies on an imposed transition location in FUN3D and the parabolized stability equations as implemented in the LASTRAC code. Predictions based on these different transition prediction approaches and models are compared with each other, experimental data, and previous simulations by evaluating the lift and drag coefficients, the surface-pressure/skin-friction distributions, and the locations of transition onset. Results are presented for multiple angles of attack for the 30P30N airfoil and CRM-HL. For the CRM-HL, a grid resolution study is performed for the LM transition model and the SA turbulence model.

High Lift↗

Generation of Performance Model for the Aeolian Wind Tunnel (AWT) Rotor at Reduced Pressure

The NASA Jet Propulsion Laboratory (JPL) designed the Mars Helicopter (MH) in collaboration with AeroVironment Inc., NASA Ames Research Center, and NASA Langley Research Center to explore the possibility of a vertical takeoff and landing (VTOL) Unmanned Aerial Vehicle (UAV) for flight on Mars. A 40-inch-diameter Aeolian Wind Tunnel (AWT) rotor, roughly approximating the proposed MH design by JPL, was tested in forward flight at Mars atmospheric pressure at the NASA Ames Planetary Aeolian Laboratory (PAL) in support of MH research efforts. This report describes the generation of the rotor model used to correlate with that experimental effort as reported by Ament and Koning. The 40-inch-diameter rotor was 3D-scanned and transformed into an airfoil deck. The scanned rotor airfoil sections are analyzed using C81 Generator (C81Gen) to generate the sectional aerodynamic coefficients for comprehensive analyses. A mid-fidelity computational fluid dynamics (CFD) simulation using Rotorcraft CFD (RotCFD) is pursued to efficiently estimate rotor hover and forward flight performance. Simulations at two pressures, 7 mbar (approximate Martian atmospheric pressure) and 1018 mbar (1 atmosphere), are performed to gain an understanding of the performance differences and Reynolds number effects observed. Experimental 1-atmosphere thrust for single- and dual-rotor isolated hover cases correlate well with the modeled rotor. Performance results at reduced pressure (7 mbar) show a drastic decrease in lift for equivalent RPMs tested at 1 atmosphere. Although this is primarily due to pressure reduction, Reynolds number effects also contribute to this decrease, as airfoil lift and drag coefficients are affected when compared with 1-atmosphere results. Further, simulated rotor power coefficient shows drastic increases at reduced pressures, attributed to laminar boundary layer separation, as described in Koning et al. for the MH rotor analysis. PAL experimental Martian Surface Wind Tunnel (MARSWIT) results are presented in the paper by Ament and Koning. The very low Reynolds number range is currently not well understood and presents various challenges for both experimentation and simulation.

Koning, Witold J. F.↗

A vortex-filament and core model for wings with edge vortex separation

A method for predicting aerodynamic characteristics of slender wings with edge vortex separation was developed. Semiempirical but simple methods were used to determine the initial positions of the free sheet and vortex core. Comparison with available data indicates that: the present method is generally accurate in predicting the lift and induced drag coefficients but the predicted pitching moment is too positive; the spanwise lifting pressure distributions estimated by the one vortex core solution of the present method are significantly better than the results of Mehrotra's method relative to the pressure peak values for the flat delta; the two vortex core system applied to the double delta and strake wing produce overall aerodynamic characteristics which have good agreement with data except for the pitching moment; and the computer time for the present method is about two thirds of that of Mehrotra's method.

Pao, J. L.↗

Flight and Stability of a Laser Inertial Fusion Energy Target in the Drift Region between Injection and the Reaction Chamber with Computational Fluid Dynamics

A Laser Inertial Fusion Energy (LIFE) target’s flight through a low Reynolds number and high Mach number regime was analyzed with computational fluid dynamics software. This regime consisted of xenon gas at 1,050 K and approximately 6,670 Pa. Simulations with similar flow conditions were performed with a sphere and compared with experimental data and published correlations for validation purposes. Transient considerations of the developing flow around the target were explored. Simulations of the target at different velocities were used to determine correlations for the drag coefficient and Nusselt number as functions of the Reynolds number. Simulations with different angles of attack were used to determine the aerodynamic coefficients of drag, lift, Magnus moment, and overturning moment as well as target stability. The drag force, lift force, and overturning moment changed minimally with spin. Above an angle of attack of 15°, the overturning moment would be destabilizing. At low angles of attack (less than 15°), the overturning moment would tend to decrease the target’s angle of attack, indicating the lack of a need for spin for stability at small angles. This stabilizing moment would cause the target to move in a mildly damped oscillation about the axis parallel to the free-stream velocity vector through the target’s center of gravity.

42 ENGINEERING↗

Flat Plate Cascades at Supersonic Speed

A brief review of exact two-dimensional supersonic flow theory and Ackeret's linearized theory are first presented. The lift and drag coefficients of a cascade of flat plates are calculated exactly and compared to those obtained using the linearized theory. The forces on the cascade are determined for unsteady inlet flow. The flat plate cascade theory is extended to compute the efficiency of a supersonic propeller with friction and finite blade thickness.

FLOW - PLATES, FLAT - SUPERSONIC↗

Accurate hydrodynamic force and torque correlations for prolate spheroids from Stokes regime to high Reynolds numbers

Detailed simulations of flow around various prolate spheroids are performed using multi-relaxation time lattice Boltzmann method (LBM). The simulations are performed in the Reynolds numbers range 0.1 ≤ Re ≤ 2000 at different incident angles 0°≤ φ ≤ 90° for various prolate spheroids of aspect ratios 1 ≤ λ ≤ 8. The Re is based on the volume equivalent sphere diameter. From the simulations, accurate correlations for average drag, lift and torque coefficients (C D , C L , and C T respectively) are proposed. The mean deviations between the correlations and the simulation data for C D , C L , and C T are 2%, 6.5%, and 4.7% respectively. Furthermore, the correlations are fitted with the physics in mind such that they can be extrapolated beyond the regimes simulated. The fits are designed such that correlations reduce to analytical (C D and C L ) solutions available for prolate spheroids in the limit Re ≈ 0. At high Re, the correlations mimic the asymptotic flattening of C D as for spheres and therefore, we expect the correlations to be valid until the critical Re (≈ 10 5 ). Furthermore, extensive comparison of our correlations with other high-fidelity simulations from literature demonstrate the accuracy of our work compared to other correlations from literature. This work enables researchers to perform accurate unresolved Euler-Lagrangian simulations for a wide range of elongated particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of an unswept propfan blade with a semiempirical dynamic stall model

The time history response of a propfan wind tunnel model with dynamic stall is studied analytically. The response obtained from the analysis is compared with available experimental data. The governing equations of motion are formulated in terms of blade normal modes which are calculated using the COSMIC-NASTRAN computer code. The response analysis considered the blade plunging and pitching motions. The lift, drag and moment coefficients for angles of attack below the static stall angle are obtained from a quasi-steady theory. For angles above static stall angles, a semiempirical dynamic stall model based on a correction to angle of attack is used to obtain lift, drag and moment coefficients. Using these coefficients, the aerodynamic forces are calculated at a selected number of strips, and integrated to obtain the total generalized forces. The combined momentum-blade element theory is used to calculate the induced velocity. The semiempirical stall model predicted a limit cycle oscillation near the setting angle at which large vibratory stresses were observed in an experiment. The predicted mode and frequency of oscillation also agreed with those measured in the experiment near the setting angle.

Reddy, T. S. R.↗

Inclined Bodies of Various Cross Sections at Supersonic Speeds

To aid in assessing effects of cross-sectional shape on body aerodynamics, the forces and moments have been measured for bodies with circular, elliptic, square, and triangular cross sections at Mach numbers 1.98 and 3.88. Results for bodies with noncircular cross sections have been compared with results for bodies of revolution having the same axial distribution of cross-sectional area (and, thus, the same equivalent fineness ratio). Comparisons have been made for bodies of fineness ratios 6 and 10 at angles of attack from 0 deg to about 20 deg and for Reynolds numbers, based on body length, of 4.0 x 10(exp 6) and 6.7 x 10(exp 6). The results of this investigation show that distinct aerodynamic advantages can be obtained by using bodies with noncircular cross sections. At certain angles of bank, bodies with elliptic, square, and triangular cross sections develop considerably greater lift and lift-drag ratios than equivalent bodies of revolution. For bodies with elliptic cross sections, lift and pitching-moment coefficients can be correlated with corresponding coefficients for equivalent circular bodies. It has been found that the ratios of lift and pitching-moment coefficients for an elliptic body to those for an equivalent circular body are practically constant with change in both angle of attack and Mach number. These lift and moment ratios are given very accurately by slender-body theory. As a result of this agreement, the method of NACA Rep. 1048 for computing forces and moments for bodies of revolution has been simply extended to bodies with elliptic cross sections. For the cases considered (elliptic bodies of fineness ratios 6 and 10 having cross-sectional axis ratios of 1.5 and 2), agreement of theory with experiment is very good. As a supplement to the force and moment results, visual studies of the flow over bodies have been made by use of the vapor-screen, sublimation, and white-lead techniques. Photographs from these studies are included in the report.

Jorgensen, Leland H.↗

Aeroelastic analysis of prop fan blades with a semiempirical dynamic stall model

The time-history response of a propfan wind-tunnel model with dynamic stall was studied analytically. The response obtained from the analysis was compared with available experimental data. The governing equations of motion were formulated in terms of blade normal modes calculated using the COSMIC-NASTRAN computer code. The response analysis considered the blade plunging and pitching motions. The lift, drag, and moment coefficients for angles of attack below the static stall angle were obtained from a quasi-steady theory. For angles above static stall angles, a semiempirical dynamic stall model based on a correction to the angle of attack was used to obtain lift, drag, and moment coefficients. Using these coefficients, the aerodynamic forces were calculated at a selected number of strips, and integrated to obtain the total generalized forces. The combined momentum-blade element theory was used to calculate the induced velocity. The semiempirical stall model predicted a limit cycle oscillation near the setting angle at which large vibratory stresses were observed in an experiment. The predicted mode and frequency of oscillation also agreed with those measured in the experiment near this setting angle. The results also correlated well with the other published data that used a semiempirical dynamic stall model based on a synthesized procedure.

Reddy, T. S. R.↗