Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Initial development for the introduction of provisions for irradiation effects in Division 5 rules

Heat pipe microreactor concept involves the use of a solid core block to encapsulate the nuclear fuel and the passive extraction of heat from the core block to the heat exchanger block by advanced heat pipes. The core block is a key component of the heat pipe microreactor design. It integrates the functions of reactor vessel, core structural components and fuel cladding of traditional Gen IV advanced reactor designs into one single structure. The effects of irradiation on the structural failure modes are outside the scope of the rules of the ASME Boiler and Pressure Vessel Code, Section III, Division 5, Subsection HB, Subpart B for metallic Class A components. Methods to account for the irradiation effect were investigated in order to develop design methods that can be applied to the core block design in the heat pipe microreactor. This report presents an initial development of an approach to account for the irradiation effects in the design rules.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1999

Fuel Preheat Effects on Soot-Field Structure in Laminar Gas Jet Diffusion Flames Burning in 0-g and 1-g

An experimental investigation conducted at the 2.2-s drop tower of the NASA Lewis Research Center is presented to quantify the influence of moderate fuel preheat on soot-field structure within 0-g laminar gas jet diffusion flames. Parallel work in 1-g is also presented to delineate the effect of elevated fuel temperatures on soot-field structure in buoyant flames. The experimental methodology implements jet diffusion flames of nitrogen-diluted acetylene fuel burning in quiescent air at atmospheric pressure. Fuel preheat of approximately 100 K in the 0-g laminar jet diffusion flames is found to reduce soot loadings in the annular region, but causes an increase in soot volume fractions at the centerline. In addition, fuel preheat reduces the radial extent of the soot field in 0-g. In 1-g, the same fuel preheat levels have a more moderated influence on soot loadings in the annular region, but are also seen to enhance soot concentrations near the axis low in the flame. The increased soot loadings near the flame centerline, as caused by fuel preheat, are consistent with the hypothesis that preheat levels of approximately 100 K enhance fuel pyrolysis rates. The results show that the growth stage of particles transported along the soot annulus is shortened both in 1-g and 0-g when elevated fuel temperatures are used.

Konsur, Bogdan↗
DOE OSTI2025

Organic Electrochemical Transistor Channel Materials: Copolymerization Versus Physical Mixing of Glycolated and Alkoxylated Polymers

Organic electrochemical transistors (OECTs) feature a polymer channel capable of conducting both ions and electronic charges. The choice of the channel material is critical for OECT performance. Many efforts have focused on improving performance via the chemical tunability of conjugated polymers – through backbone, side chain, and molar mass engineering – leading to useful design principles for accumulation-mode OECT materials. However, tuning the chemical structure of conjugated polymers often requires time-consuming optimization of the synthesis route. Meanwhile, variations in molar mass, dispersity, structural defects, and metal content present challenges when attempting to analyze the detailed effects of structural modifications, as multiple performance-determining factors are often (unintentionally) changed at the same time. Therefore, this study explores blended channel materials obtained by physically mixing glycolated and alkoxylated polymers in different ratios, and compares their OECT performance with the corresponding statistical copolymers. It is shown that mixing two well-performing materials creates blends that enable rational tuning of the transistor properties without compromising on performance. Thus, channels based on blends of alkoxylated and glycolated polymers hold promise for OECT technology with tailored response, as only two materials are needed to achieve any desired side chain ratio, simplifying the optimization of OECT characteristics.

copolymerization↗
NASA NTRS1975

Mossbauer effect in dilute iron alloys

The effects of variable concentration, x, of Aluminum, Germanium, and Lanthanum atoms in Iron lattice on various Mossbauer parameters was studied. Dilute binary alloys of (Fe-Al), (Fe-Ge), (Fe-Al) containing up to x = 2 a/o of the dilute constituent were prepared in the form of ingots and rolled to a thickness of 0.001 in. Mossbauer spectra of these targets were then studied in transmission geometry to measure changes in the hyperfine field, peak widths isomer shifts as well as the ratio of the intensities of peaks (1,6) to the intensities of peaks (2,5). It was shown that the concept of effective hyperfine structure field in very dilute alloys provides a useful means of studying the effects of progressively increasing the solute concentration on host lattice properties.

Singh, J. J.↗
NASA NTRS1977

Dynamic response of some tentative compliant wall structures to convected turbulence fields

Some tentative compliant wall structures designed for possible skin friction drag reduction are investigated. Among the structural models considered is a ribbed membrane backed by polyurethane or PVS plastisol. This model is simplified as a beam placed on a viscoelastic foundation as well as on a set of evenly spaced supports. The total length of the beam may be either finite or infinite, and the supports may be either rigid or elastic. Another structural model considered is a membrane mounted over a series of pretensioned wires, also evenly spaced, and the entire membrane is backed by an air cavity. The forcing pressure field is idealized as a frozen random pattern convected downstream at a characteristic velocity. The results are given in terms of the frequency response functions of the system, the spectral density of the structural motion, and the spectral density of the boundary layer pressure including the effect of structural motion. These results are used in a parametric study of structural configurations capable of generating favorable wave lengths, wave amplitudes, and wave speeds in the structural motion for potential drag reduction.

Nijim, H. H.↗
NASA NTRS1992

Structure, processing, and properties of potatoes

The objective of this experiment and lesson intended for high school students in an engineering or materials science course or college freshmen is to demonstrate the relation between processing, structure, and thermodynamic and physical properties. The specific objectives are to show the effect of structure and structural changes on thermodynamic properties (specific heat) and physical properties (compressive strength); to illustrate the first law of thermodynamics; to compare boiling a potato in water with cooking it in a microwave in terms of the rate of structural change and the energy consumed to 'process' the potato; and to demonstrate compression testing.

Lloyd, Isabel K.↗
NASA NTRS1992

Analysis of composite structures with delaminations under combined bending and compression

A methodology had been developed for strength prediction of composite structures with delaminations under combined bending and compression loads. The methodology is an extension of the delamination analysis method developed under the USAF/Boeing/Northrop 'Damage Tolerance of Composites' program. Delamination buckling and strain energy release rate analyses are used as basic tools in the strength prediction. In addition, failure mode interaction and structural configuration effects are considered. The influence of fasteners on the strength of a delaminated structure is incorporated to evaluate assembly-caused delaminations. The capabilities and limitations of the analysis method are shown by correlating the analytical results with the existing experimental data. The failure load, failure mode and failure sequence of a structure containing delaminations are predicted and the analytical results are compared with test data.

Kan, Han-Pin↗
NASA NTRS2000

Flame Design: A Novel Approach Developed to Produce Clean, Efficient Diffusion Flames

Soot formation and flame extinction are vital concerns in the combustion of fossil fuels. In particular, soot is responsible for pollutant emissions, and extinction can cause inefficient or unstable burning. Normal-gravity experiments have demonstrated that flames can be designed to improve both characteristics by redirecting some or all of the nitrogen from the oxidizer into the fuel. Such nitrogen exchange can produce permanently blue flames, which are soot free under all possible flame conditions. Furthermore, this approach can lead to stronger, extinction-resistant flames. Past investigations of nitrogen exchange were unable to identify the physical mechanisms responsible for its benefits because these mechanisms cannot be isolated when normal-gravity flames are studied. In contrast, the Diffusion Flame Extinction and Soot Inception (DESI) experiment considers spherical flames, where nearly perfect spherical symmetry affords new levels of control. Because of buoyancy, spherical flames cannot be created in Earth s gravity. DESI was conceived by principal investigator Professor R.L. Axelbaum of Washington University in St. Louis. Tests to date have utilized the 2.2-Second Drop Tower at the NASA Glenn Research Center at Lewis Field. The experiment is slated for testing aboard the International Space Station in a few years. Two mechanisms have been proposed to explain the connection between nitrogen exchange and permanently blue flames. These are the structure (chemical effects) and hydrodynamics (flow direction and speed). In normal-gravity flames, the structure and hydrodynamics are coupled, since nitrogen exchange simultaneously modifies both. Spherical microgravity flames, on the other hand, allow independent control of these factors. Specifically, structure can be modified via nitrogen exchange, and flow direction can be reversed by swapping the ambient and burner-feed gases. In DESI, these variations can be accomplished without changing the theoretical flame temperature.

Axelbaum, Richard L.↗
NASA NTRS2010

Utilizing In Situ Directional Hyperspectral Measurements to Validate Bio-Indicator Simulations for a Corn Crop Canopy

Two radiative transfer canopy models, SAIL and the two-layer Markov-Chain Canopy Reflectance Model (MCRM), were coupled with in situ leaf optical properties to simulate canopy-level spectral band ratio vegetation indices with the focus on the photochemical reflectance index in a cornfield. In situ hyperspectral measurements were made at both leaf and canopy levels. Leaf optical properties were obtained from both sunlit and shaded leaves. Canopy reflectance was acquired for eight different relative azimuth angles (psi) at three different view zenith angles (Theta (sub v)), and later used to validate model outputs. Field observations of photochemical reflectance index (PRI) for sunlit leaves exhibited lower values than shaded leaves, indicating higher light stress. Canopy PRI expressed obvious sensitivity to viewing geometry, as a function of both Theta (sub v) and psi . Overall, simulations from MCRM exhibited better agreements with in situ values than SAIL. When using only sunlit leaves as input, the MCRM-simulated PRI values showed satisfactory correlation and RMSE, as compared to in situ values. However, the performance of the MCRM model was significantly improved after defining a lower canopy layer comprised of shaded leaves beneath the upper sunlit leaf layer. Four other widely used band ratio vegetation indices were also studied and compared with the PRI results. MCRM simulations were able to generate satisfactory simulations for these other four indices when using only sunlit leaves as input; but unlike PRI, adding shaded leaves did not improve the performance of MCRM. These results support the hypothesis that the PRI is sensitive to physiological dynamics while the others detect static factors related to canopy structure. Sensitivity analysis was performed on MCRM in order to better understand the effects of structure related parameters on the PRI simulations. Leaf area index (LAI) showed the most significant impact on MCRM-simulated PRI among the parameters studied. This research shows the importance of hyperspectral and narrow band sensor studies, and especially the necessity of including the green wavelengths (e.g., 531 nm) on satellites proposing to monitor carbon dynamics of terrestrial ecosystems.

Cheng, Yen-Ben↗
NASA NTRS1994

Effects of heavy-element settling on solar neutrino fluxes and interior structure

We consider the effects of gravitational settling of both He and heavier elements on the predicted solar neutrino fluxes and interior sound speed and density profiles. We find that while the structural changes that result from the inclusion of both He and heavy-element settling are only slightly larger than the changes resulting from the inclusion of He settling alone, the additional increases in expected neutrino fluxes are of comparable size. Our preferred model with both He and heavy-element settling has neutrino count rates of 9.0 SNU for Cl-37 detectors and 137 SNU for Ga-71 detectors, as compared to 7.1 and 127 SNU for a comparable model without any diffusive separation, or 8.0 and 132 SNU for a model that includes He settling alone. We suggest that the correction factors by which the predicted neutrino fluxes of solar models calculated without including the effects of diffusion should be multiplied are 1.25 +/- 0.08 for Cl detectors, 1.07 +/- 0.02 for Ga detectors, and 1.28 +/- 0.09 for the B-8 flux (1 sigma errors). Comparison of internal sound speed and density profiles strongly suggests that the additional changes in calculated p-mode oscillation frequencies due to the inclusion of heavy-element settling will be small compared to the changes that result from He settling alone, especially for the higher degree modes. All models with diffusive separation give much better agreement with the observed depth of the convection zone than do nondiffusive models. The model that includes both He and heavy-element settling requires an initial He mass fraction Y = 0.280 and has a surface He abundance of Y = 0.251 at the solar age.

Proffitt, Charles R.↗
NASA NTRS1980

Energy minimization versus pseudo force technique for nonlinear structural analysis

The effectiveness of using minimization techniques for the solution of nonlinear structural analysis problems is discussed and demonstrated by comparison with the conventional pseudo force technique. The comparison involves nonlinear problems with a relatively few degrees of freedom. A survey of the state-of-the-art of algorithms for unconstrained minimization reveals that extension of the technique to large scale nonlinear systems is possible.

Kamat, M. P.↗
NASA NTRS1980

Preliminary study on the potential usefulness of array processor techniques for structural synthesis

The effects of the use of array processor techniques within the structural analyzer program, SPAR, are simulated in order to evaluate the potential analysis speedups which may result. In particular the connection of a Floating Point System AP120 processor to the PRIME computer is discussed. Measurements of execution, input/output, and data transfer times are given. Using these data estimates are made as to the relative speedups that can be executed in a more complete implementation on an array processor maxi-mini computer system.

Feeser, L. J.↗
DOE OSTI2020

Investigation of the Effect of Temperature on the Structure of SARS-CoV-2 Spike Protein by Molecular Dynamics Simulations

Statistical and epidemiological data imply temperature sensitivity of the SARS-CoV2 coronavirus. However, the molecular level understanding of the virus structure at different temperature is still not clear. Spike protein is the outermost structural protein of the SARS-CoV-2 virus which interacts with the Angiotensin Converting Enzyme 2 (ACE2), a human receptor, and enters the respiratory system. In this study, we performed an all atom molecular dynamics simulation to study the effect of temperature on the structure of the Spike protein. After 200 ns of simulation at different temperatures, we came across some interesting phenomena exhibited by the protein. We found that the solvent exposed domain of Spike protein, namely S1, is more mobile than the transmembrane domain, S2. Structural studies implied the presence of several charged residues on the surface of N-terminal Domain of S1 which are optimally oriented at 10– 30°C. Bioinformatics analyses indicated that it is capable of binding to other human receptors and should not be disregarded. Additionally, we found that receptor binding motif (RBM), present on the receptor binding domain (RBD) of S1, begins to close around temperature of 40°C and attains a completely closed conformation at 50°C. We also found that the presence of glycan moieties did not influence the observed protein dynamics. Nevertheless, the closed conformation disables its ability to bind to ACE2, due to the burying of its receptor binding residues. Our results clearly show that there are active and inactive states of the protein at different temperatures. This would not only prove beneficial for understanding the fundamental nature of the virus, but would be also useful in the development of vaccines and therapeutics.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1998

Effect of Uncertainty of Identified Parameters on Structural Damage Detection

This paper presents a study of the effect of the uncertainty of identified parameters on the damage detection of structure. The identified parameters, which are obtained by applying system identification algorithms to analyze the time-domain response data, have uncertainty due to noise, environmental change, etc. The damage of some structural elements may have less effect on the identified parameters than noise or environmental change, so some damage situations cannot be distinguished under these circumstances. An algorithm is presented to determine whether the considered damage can be distinguished. A twenty-bay truss structure is used to demonstrate and verify the study.

Davidson, Mario↗