Search NASA⌕ Search

SEARCH · Search NASA

Results for “VAPOR PHASE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Enhancement of lanthanide evaporation by complexation: Dysprosium tri-iodide mixed with indium iodide and thulium tri-iodide mixed with thallium iodide

The vapors in equilibrium with condensates of DyI{sub 3}, DyI{sub 3}/InI, TmI{sub 3}, and TmI{sub 3}/TlI were observed over the temperature range from 900 K to 1400 K using x-ray induced fluorescence. The total densities of each element (Dy, Tm, In, Tl, and I) in the vapor, summed over all atomic and molecular species, were determined. Dramatic enhancements in the total vapor densities of Dy and Tm were observed in the vapors over DyI{sub 3}/InI and TmI{sub 3}/TlI as compared to the vapors over pure DyI{sub 3} and pure TmI{sub 3}, respectively. An enhancement factor exceeding 10 was observed for Dy at T≈ 1020 K, decreasing to 0 at T≈ 1250 K. An enhancement factor exceeding 20 was observed for Tm at T≈ 1040 K, decreasing to 0 at T≈ 1300 K. Such enhancements are expected from the formation of the vapor-phase hetero-complexes DyInI{sub 4} and TmTlI{sub 4}. Numerical simulations of the thermo-chemical equilibrium suggest the importance of additional complexes in liquid phases. A description of the measurement technique is given. Improvements in the absolute calibration lead to an approximately 40% correction to previously reported preliminary results [J. J. Curry et al., Chem. Phys. Lett. 507, 52 (2011); Appl. Phys. Lett. 100, 083505 (2012)].

36 MATERIALS SCIENCE↗

Moving beyond the limits of mass transport in liquid absorbent microfilms through the implementation of surface-induced vortices

The slow diffusion of an absorbate molecule into an absorbent often makes the absorption process a rate-limiting step in many applications. In cases involving an absorbate with a high heat of phase change, such as water absorption into a LiBr (lithium bromide) solution, the absorption rate is further slowed due to significant heating of the absorbent. Recently, it has been demonstrated that constraining a LiBr solution film by a hydrophobic porous structure enables manipulation of the solution flow thermohydraulic characteristics. Here, it is shown that mass transport mode in a constrained laminar solution flow can be changed from diffusive to advective. This change in mode is accomplished through stretching and folding the laminar streamlines within the solution film via the implementation of micro-scale features on the flow channel surface. The process induces vortices within the solution film, which continuously bring concentrated solution from the bottom and middle of the solution channel to its interface with the vapor phase, thus leading to a significant enhancement in the absorption rate. The detailed physics of the involved transport processes is elucidated using the LBM (Lattice Boltzmann Method). Published by Elsevier Ltd.

Bigham, S↗

Theory of the photomolecular effect

It is well-known that water in liquid and vapor phases exhibits weak visible-light absorption. Recent experiments, however, show that at the liquid-air interface, absorption drastically increases, accelerating evaporation beyond thermal limits by 2–5 times. Strikingly, evaporation peaks at green wavelengths, despite no corresponding absorptance peak. The underlying mechanism of this observation, termed the photomolecular effect, remains puzzling, particularly as water molecules do not exhibit resonance peaks in the visible spectrum. Here, we present a theoretical model explaining the effect. We show that surface-bound water clusters undergo non-resonant photon-driven evaporation, with green light being particularly effective. Crucially, we do not expect green light to couple more strongly than other wavelengths to the molecules at the surface, rather the energy of green light is more effectively used to vaporize water. Our model accounts for why the evaporation peak does not align with absorptance and provides a quantum mechanical explanation of how a single photon can vaporize an entire molecular cluster. This model challenges conventional views on water-light interactions, revealing a fundamentally non-thermal evaporation mechanism. Furthermore, our findings have implications for water purification, energy-efficient drying, and climate modeling, opening new pathways for optimizing evaporation-based technologies.

Interfacial evaporation↗

Spray Mechanism of Contained-Electrospray Ionization

Analytical characteristics of contained electrospray ionization (ESI) are summarized in terms of its potential to modify the analyte solution during the stages of droplet formation to provide opportunities to generate native versus denatured biomolecular gas-phase ions, without the need for bulk-phase analyte modifications. The real-time modification of the charged microdroplets occurs in a cavity that is included in the outlet of the contained-ESI ion source. Close examination of the inside of the cavity using a high-speed camera revealed the formation of discrete droplets as well as thin liquid films in the droplets wake. When operated at 20 psi N2 pressure, the droplets were observed to move at an average speed of 8 mm/s providing ~1 s mixing time in a 10 mm cavity length. Evidence is provided for the presence of highly reactive charged droplets based on myoglobin charge state distribution, apo-myoglobin contents, and ion mobility drift time profiles under different spray conditions. Mechanistic insights for the capture of vapor-phase reagents and droplet dynamics as influenced by different operational modes are also described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Luminescence of (ZnSe:Al):Yb Сrystals at 4.2 K

It is established that the doping of ZnSe:Al crystals with ytterbium from the vapor phase brings about the appearance of two new bands in the low-temperature luminescence spectra. Emission in the energy range 1.15–1.35 eV is defined by transitions in Yb{sup 3+} ions, and the edge band is defined by the LO-phonon-assisted transitions of free electrons to acceptor levels of uncontrollable Li impurities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Terahertz injection lasers based on PbSnSe alloy with an emission wavelength up to 46.5 μm

Diffusion injection lasers based on Pb{sub 1} {sub –} {sub x}Sn{sub x}Se alloy, emitting in a wide spectral range of 10–46.5 μm depending on the composition and temperatures are fabricated. A technology for growing high-quality single crystals from the vapor phase under conditions of free growth is developed. The dependences of the total emission intensity on the pump current and the emission spectra of injection lasers based on Pb{sub 1–x}Sn{sub x}Se are studied. In these samples, lasing of long-wavelength radiation to a record wavelength of 46.5 μm is achieved.

36 MATERIALS SCIENCE↗

Finite Element Models for Electron Beam Freeform Fabrication Process

Electron beam freeform fabrication (EBF3) is a member of an emerging class of direct manufacturing processes known as solid freeform fabrication (SFF); another member of the class is the laser deposition process. Successful application of the EBF3 process requires precise control of a number of process parameters such as the EB power, speed, and metal feed rate in order to ensure thermal management; good fusion between the substrate and the first layer and between successive layers; minimize part distortion and residual stresses; and control the microstructure of the finished product. This is the only effort thus far that has addressed computer simulation of the EBF3 process. The models developed in this effort can assist in reducing the number of trials in the laboratory or on the shop floor while making high-quality parts. With some modifications, their use can be further extended to the simulation of laser, TIG (tungsten inert gas), and other deposition processes. A solid mechanics-based finite element code, ABAQUS, was chosen as the primary engine in developing these models whereas a computational fluid dynamics (CFD) code, Fluent, was used in a support role. Several innovative concepts were developed, some of which are highlighted below. These concepts were implemented in a number of new computer models either in the form of stand-alone programs or as user subroutines for ABAQUS and Fluent codes. A database of thermo-physical, mechanical, fluid, and metallurgical properties of stainless steel 304 was developed. Computing models for Gaussian and raster modes of the electron beam heat input were developed. Also, new schemes were devised to account for the heat sink effect during the deposition process. These innovations, and others, lead to improved models for thermal management and prediction of transient/residual stresses and distortions. Two approaches for the prediction of microstructure were pursued. The first was an empirical approach involving the computation of thermal gradient, solidification rate, and velocity (G,R,V) coupled with the use of a solidification map that should be known a priori. The second approach relies completely on computer simulation. For this purpose a criterion for the prediction of morphology was proposed, which was combined with three alternative models for the prediction of microstructure; one based on solidification kinetics, the second on phase diagram, and the third on differential scanning calorimetry data. The last was found to be the simplest and the most versatile; it can be used with multicomponent alloys and rapid solidification without any additional difficulty. For the purpose of (limited) experimental validation, finite element models developed in this effort were applied to three different shapes made of stainless steel 304 material, designed expressly for this effort with an increasing level of complexity. These finite element models require large computation time, especially when applied to deposits with multiple adjacent beads and layers. This problem can be overcome, to some extent, by the use of fast, multi-core computers. Also, due to their numerical nature coupled with the fact that solid mechanics- based models are being used to represent the material behavior in liquid and vapor phases as well, the models have some inherent approximations that become more pronounced when dealing with multi-bead and multi-layer deposits.

Chandra, Umesh↗

Characterization and In-Situ Monitoring of ZnSe Crystal Growth by Seeded PVT for Microgravity Applications

Crystal growth from the vapor phase continues to play a significant role in the production of II-VI semiconductor compounds (ZnO, ZnTe, CdTe, etc.) and SiC. As compared to melt growth methods (where available) the advantages are: (1) lower growth temperature(s); (2) reduction in defect concentration; (3) additional purification; and (4) enhanced crystal perfection. A powerful tool in determining the mechanism of PVT is microgravity. Under normal gravity conditions the transport mechanism is a superposition of diffusive and convective fluxes. Microgravity offers the possibility of studying the transport properties without the influence of convective effects. Research on the crystal growth of ZnSe by PVT (P.I.: Su of NASA/MSFC) will help to clarify the effects of convection on crystal growth. A crystal growth furnace with in-situ and real time optical monitoring capabilities was constructed and used to monitor the vapor composition and growing crystal surface morphology during the PVT growth of ZnSe. Using photoluminescence and SIMS, ex-situ, the incorporation of point defects (Zn vacancy) and impurities was found to be correlated to the gravity vector due to the influence of the convective flow. A summary of the results to date will be presented.

Feth, Shari T.↗

Two-chamber configuration of Bio-Nano electron cyclotron resonance ion source for fullerene modification

We report on the modification of fullerenes with iron and chlorine using two individually controllable plasmas in the Bio-Nano electron cyclotron resonance ion source (ECRIS). One of the plasmas is composed of fullerene and the other one is composed of iron and chlorine. The online ion beam analysis allows one to investigate the rate of the vapor-phase collisional modification process in the ECRIS, while the offline analyses (e.g., liquid chromatography-mass spectrometry) of the materials deposited on the plasma chamber can give information on the surface-type process. Both analytical methods show the presence of modified fullerenes such as fullerene-chlorine, fullerene-iron, and fullerene-chlorine-iron.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

ZIF‐8 Membrane Permselectivity Modification by Manganese(II) Acetylacetonate Vapor Treatment

Abstract Vapor‐phase treatment of ZIF‐8 membranes with manganese(II) acetylacetonate (Mn(acac) 2 ) allows permselectivity tuning. Propylene/propane selectivity increases from 31 to 210 after the Mn(acac) 2 treatment at 165 °C for 30 min, while selectivities increase from 14.6 to 242 for H 2 /CH 4 , from 2.9 to 38 for CO 2 /CH 4 , from 2.4 to 29 for CO 2 /N 2 , and from 2.9 to 7.5 for O 2 /N 2 , after Mn(acac) 2 treatment at 175 °C for 30 min. Stable equimolar propylene/propane mixture selectivity of 165 at ambient temperature and 4 bar equimolar feed with a propylene flux of 8.3×10 −4 mol m −2 s −1 is established. A control experiment excludes thermal treatment alone causing these changes. XPS analysis reveals the presence of Mn(acac) 2 on the outer surface of the vapor‐treated ZIF‐8 membranes while no other changes are detectable by X‐ray diffraction and infrared spectroscopy.

Hayashi, Mikio↗

Abatement of radioiodine in aqueous reprocessing off-gas

The reprocessing used nuclear fuel (UNF) releases volatile fission and activation products, including 129 I, into the off-gas of a processing plant. Mitigation of the release of vapor phase radionuclides is necessary for meeting regulatory requirements in the United States and other countries. In an aqueous reprocessing plant, volatile radioiodine could be present in several forms, depending on the chemistry of the process used. Inorganic iodine will be the predominate species in any shearing or voloxidation pretreatment off-gas and dissolver off-gas (DOG). Organic iodides such as CH 3 I, C 4 H 9 I, and C 12 H 25 I have been proposed to be generated during solvent extraction; thus, these species must be captured from the vessel off-gas (VOG). The abatement of inorganic and organic iodide species to meet United States regulatory requirements has been demonstrated in laboratory experiments using Ag-based solid sorbents. The data presented in this paper includes the effect of gas composition (e.g., the presence of water vapor and NO x ), iodine speciation (I 2 , CH 3 I, C 4 H 9 I, C 12 H 25 I), and sorbent bed parameters (e.g., temperature, sorbent age) on complete iodine capture on Ag-mordenite in an aqueous reprocessing plant.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Observation of ultralow-level Al impurities on a silicon surface by high-resolution grazing emission x-ray fluorescence excited by synchrotron radiation

We demonstrate that ultralow-level Al impurities on a silicon surface can be measured by using the high-resolution grazing emission x-ray fluorescence (GEXRF) technique combined with synchrotron-radiation excitation. An Al-impurity level of about 10{sup 12} atoms/cm{sup 2} was reached by observing the Al K{alpha} x-ray fluorescence in the resonant Raman-scattering background-''free'' regime by choosing an appropriate beam energy below the Si K absorption edge. Present results show that by combining the GEXRF method with the vapor phase decomposition technique the 10{sup 7} atoms/cm{sup 2} level can be reached for Al detection on silicon. Finally, we found that the high-resolution GEXRF technique is a sensitive tool to study the morphology of surface nanostructures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The roles of the binodal curve and the spinodal curve in expansions from the supercritical state with flashing

Data extracted from time-of-flight (TOF) measurements made on steady-state He free jets at Göttingen already in 1986 and for pulsed Ne free jets investigated recently at Tel Aviv have been added to an earlier plot of terminal condensed-phase mass fraction x{sub 2∞} as a function of the dimensionless scaling parameter Γ. Γ characterizes the source (fluid species, temperature, pressure and throat diameter); values of x{sub 2∞} are extracted from TOF measurements using conservation of energy in the free-jet expansion. For nozzles consisting of an orifice in a thin plate; the extracted data yield 22 data points which are correlated satisfactorily by a single curve. The Ne free jets were expanded from a conical nozzle with a 20° half angle; the three extracted data points stand together but apart from the aforementioned curve, indicating that the presence of the conical wall influences significantly the expansion and hence the condensation. The 22 data points for the expansions via an orifice consist of 15 measurements with expansions from the gas-phase side of the binodal curve which crossed the binodal curve downstream from the sonic point and 7 measurements with expansions of the gas-phase product of the flashing which occurred after an expansion from the liquid-phase side of the binodal curve crossed the binodal curve upstream from the sonic point. The association of these 22 points with a single curve supports the alternating-phase model for flows with flashing upstream from the sonic point proposed earlier. In order to assess the role of the spinodal curve in such expansions, the spinodal curves for He and Ne were computed using general multi-parameter Helmholtz-free-energy equation-of-state formulations. Then, for the several sets of source-chamber conditions used in the free-jet measurements, thermodynamic states at key locations in the free-jet expansions (binodal curve, sonic point and spinodal curve) were evaluated, with the expansion presumed to be metastable from the binodal curve to the spinodal curve. TOF distributions with more than two peaks (interpreted earlier as superimposed alternating-state TOF distributions) indicated flashing of the metastable flow downstream from the binodal curve but upstream from the sonic point. This relatively early flashing is due apparently to destabilizing interactions with the walls of the source. If the expansion crosses the binodal curve downstream from the nozzle, the metastable fluid does not interact with surfaces and flashing might be delayed until the expansion reaches the spinodal curve. It is concluded that, if the expansion crosses the binodal curve before reaching the sonic point, the resulting metastable fluid downstream from the binodal curve interacts with the adjacent surfaces and flashes into liquid and vapor phases which expand alternately through the nozzle; the two associated alternating TOF distributions are superposed by the chopping process so that the result has the appearance of a single distribution with three peaks.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Process Intensification of Distillation using a Microwick Technology to Demonstrate Separation of Propane and Propylene

Process intensification (PI) of distillation using a microchannel distillation (MCD) device successfully reduced the height of a theoretical plate (HETP) in separating propane and propylene to 1 cm, representing 10 theoretical stages. Mass transfer is enhanced by using thin wicking structures that are 0.17 mm thick in counter-flow with vapor. Liquid is segregated in the wicks by applying a siphon, which also enables the device to operate horizontally. A scalable device containing 11 wicks was operated cryogenically in total reflux. The HETP varied between 1.0 and 3.7 cm, representing a dramatic reduction over commercial structured packings and comparable to other PI approaches. Significant improvements are expected with further development. Potential application for intensified distillation processes include distributed manufacturing and difficult separations involving close boiling compounds and meeting high purity specifications. The ultimate application is isotopic enrichment, where the number of stages required is typically multiple thousands.

Distillation, Process Intensification, Microchanne↗

From Deposition to Encapsulation: Roll-to-roll manufacturing of organic light emitting devices for lighting (Final Report)

Organic light emitting devices (OLEDs) are promising solid state light sources due to their high efficiency, high color quality and flexible form factors. The key to enable low cost OLED lighting, is to rapidly fabricate thin film organic layers on a continuous flexible roll, called R2R processing. This project aims to investigate the feasibility of mass production of OLED lighting using the R2R process, from deposition to encapsulation. A high efficiency white OLED is fabricated on 10 cm-wide substrate rolls in a pilot R2R tool comprising of two different organic deposition: vacuum thermal evaporation (VTE) and organic vapor phase deposition (OVPD). A high quality encapsulation process to package OLEDs is demonstrated using an atomic layer deposition tool integrated to the R2R system without air exposure. The method to achieve ultrahigh deposition rates required by R2R processing is demonstrated by OVPD. Uniform organic semiconductor thin films grown by OVPD at rates as high as 50 Å/s are achieved. A comprehensive numerical model that is capable of simulating complex, multilayer WOLED structures is developed to provide an alternative to experimental iterations of OLED design and tests. A cost estimate on the R2R production of WOLEDs for lighting is developed. Assuming a WOLED luminance of 10 klm/m 2 , the cost of a WOLED light engine is anticipated to be $\$ 12.5$ /klm. With incremental reduction in material and driver costs and improved luminance, the cost of WOLED lighting can be reduced to $\$ 6.3$ /klm in the near term. These findings suggest OLED lighting can be volume manufactured by R2R vapor deposition methods with much reduced costs compared to current batch processing methods, potentially positioning WOLEDs for use in numerous premium lighting applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Effect of the Surface Modification of Synthetic Diamond with Nickel or Tungsten on the Properties of Copper–Diamond Composites

Tungsten- and nickel-containing coatings have been produced on the surface of synthetic diamond crystals by rotary chemical vapor deposition (RCVD) using tungsten hexacarbonyl, W(CO){sub 6}, and nickelocene, Ni(C{sub 5}H{sub 5}){sub 2}, as gaseous precursors. The thickness, composition, and morphology of the coatings have been shown to depend on the RCVD process duration and reactant concentrations in the vapor phase. The synthetic diamond microcrystals with tungsten- and nickel-containing coatings have been used to produce copper–diamond heat-conducting composites. Powder mixtures containing 50 vol % diamond with a particle size of 50, 100, or 200 μm have been consolidated by spark plasma sintering or hot pressing. It has been shown that the highest relative density (97%) and thermal conductivity (340 W/(m K)) are offered by the composites produced by spark plasma sintering using tungsten carbide-coated 50-μm diamond crystals.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Use Of The Operational Air Quality Monitor (AQM) For In-Flight Water Testing Project

A primary requirement for manned spaceflight is Environmental Health which ensures air and water contaminants, acoustic profiles, microbial flora, and radiation exposures within the cabin are maintained to levels needed for crew health and for vehicle system functionality. The reliance on ground analyses of returned samples is a limitation in the current environmental monitoring strategy that will prevent future Exploration missions beyond low-Earth orbit. This proposal attempts to address this shortcoming by advancing in-flight analyses of water and air. Ground analysis of in-flight, air and water samples typically employ vapor-phase analysis by gas chromatography-mass spectrometry (GC-MS) to identify and quantify organic compounds present in the samples. We envision the use of newly-developed direct ionization approaches as the most viable avenue leading towards an integrated analytical platform for the monitoring of water, air, and, potentially bio-samples in the cabin environment. Development of an in-flight instrument capable of analyzing air and water samples would be the logical next step to meeting the environmental monitoring needs of Exploration missions. Currently, the Air Quality Monitor (AQM) on-board ISS provides this specific information for a number of target compounds in the air. However, there is a significant subset of common target compounds between air and water. Naturally, the following question arises, "Can the AQM be used for both air and water quality monitoring?" Previous directorate-level IR&D funding led to the development of a water sample introduction method for mass spectrometry using electrothermal vaporization (ETV). This project will focus on the integration of the ETV with a ground-based AQM. The capabilities of this integrated platform will be evaluated using a subset of toxicologically important compounds.

Macatangay, Ariel↗