Search NASA⌕ Search

SEARCH · Search NASA

Results for “assembly reliability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

A Two-Wheel Observing Mode for the MAP Spacecraft

The Microwave Anisotropy Probe (MAP) is a follow-on to the Differential Microwave Radiometer (DMR) instrument on the Cosmic Background Explorer (COBE). Due to the MAP project's limited mass, power, and budget, a traditional reliability concept including fully redundant components was not feasible. The MAP design employs selective hardware redundancy, along with backup software modes and algorithms, to improve the odds of mission success. This paper describes the effort to develop a backup control mode, known as Observing II, that will allow the MAP science mission to continue in the event of a failure of one of its three reaction wheel assemblies. This backup science mode requires a change from MAP's nominal zero-momentum control system to a momentum-bias system. In this system, existing thruster-based control modes are used to establish a momentum bias about the sun line sufficient to spin the spacecraft up to the desired scan rate. Natural spacecraft dynamics exhibits spin and nutation similar to the nominal MAP science mode with different relative rotation rates, so the two reaction wheels are used to establish and maintain the desired nutation angle from the sun line. Detailed descriptions of the ObservingII control algorithm and simulation results will be presented, along with the operational considerations of performing the rest of MAP's necessary functions with only two wheels.

Starin, Scott R.↗

Computational methods and software systems for dynamics and control of large space structures

The deployment, assembly and mission-oriented maneuvering of space structures in orbit will trigger large motions of flexible, truss-type structures. In addition, the presence of on-board controls both for attitude stabilization and specified vibration tolerance requirements may further complicate the dynamic behavior of the orbiting structures. Because of safety and cost considerations, the dynamic response of the combined structural and control systems must be predicted reliably. This need can only be met through the development of reliable and efficient simulation capabilities, since there is general agreement that on-orbit experiments should be limited because of cost, time and facility constraints. The long-term objective of this research effort is to develop a next-generation computer simulator for the dynamics and control of large space structures. The simulator will be based on integrating four research thrusts: a new multibody dynamics formulation methodology, modeling capabilities in long/slender truss-beam components with realistic joints, efficient computational procedures that can be implemented either in sequential or concurrent computers, and prototype simulation modules that can be easily processed into a modern large-scale engineering software system such as the NASA/Computational Structural Mechanics (CSM) testbed.

Park, K. C.↗

Solar powered Stirling cycle electrical generator

Under NASA's Civil Space Technology Initiative (CSTI), the NASA Lewis Research Center is developing the technology needed for free-piston Stirling engines as a candidate power source for space systems in the late 1990's and into the next century. Space power requirements include high efficiency, very long life, high reliability, and low vibration. Furthermore, system weight and operating temperature are important. The free-piston Stirling engine has the potential for a highly reliable engine with long life because it has only a few moving parts, non-contacting gas bearings, and can be hermetically sealed. These attributes of the free-piston Stirling engine also make it a viable candidate for terrestrial applications. In cooperation with the Department of Energy, system designs are currently being completed that feature the free-piston Stirling engine for terrestrial applications. Industry teams were assembled and are currently completing designs for two Advanced Stirling Conversion Systems utilizing technology being developed under the NASA CSTI Program. These systems, when coupled with a parabolic mirror to collect the solar energy, are capable of producing about 25 kW of electricity to a utility grid. Industry has identified a niche market for dish Stirling systems for worldwide remote power application. They believe that these niche markets may play a major role in the introduction of Stirling products into the commercial market.

Shaltens, Richard K.↗

Space Shuttle Solid Rocket Motor Program - Lessons learned

An evaluation is given of the most important lessons learned concerning the Space Shuttle's Solid Rocket Motors with respect to flight safety, reuse requirements, system reliability, structural integrity, and hardware damage due to reentry, water impact, and retrieval. Within the major categories of flight safety, performance, and reuse/cost, priorities are identified for implementation of envisioned improvements; schedule and cost considerations are noted to have been substantially downgraded in favor of flight safety. The consequences of the primacy of flight safety are discussed in the areas of primary systems design, redundant systems, manufacturing and assembly processing, and launch constraints.

Mccool, A. A.↗

Designing a Composable Geometric Toolkit for Versatility in Applications to Simulation Development

Conceived and implemented through the development of probabilistic risk assessment simulations for Project Constellation, the Geometric Toolkit allows users to create, analyze, and visualize relationships between geometric shapes in three-space using the MATLAB computing environment. The key output of the toolkit is an analysis of how emanations from one "source" geometry (e.g., a leak in a pipe) will affect another "target" geometry (e.g., another heat-sensitive component). It can import computer-aided design (CAD) depictions of a system to be analyzed, allowing the user to reliably and easily represent components within the design and determine the relationships between them, ultimately supporting more technical or physics-based simulations that use the toolkit. We opted to develop a variety of modular, interconnecting software tools to extend the scope of the toolkit, providing the capability to support a range of applications. This concept of simulation composability allows specially-developed tools to be reused by assembling them in various combinations. As a result, the concepts described here and implemented in this toolkit have a wide range of applications outside the domain of risk assessment. To that end, the Geometric Toolkit has been evaluated for use in other unrelated applications due to the advantages provided by its underlying design.

Reed, Gregory S.↗

Innovations in Mission Architectures for Human and Robotic Exploration Beyond Low Earth Orbit

Through the application of advanced technologies, mission concepts, and new ideas in combining capabilities, architectures for missions beyond Earth orbit have been dramatically simplified. These concepts enable a stepping stone approach to discovery driven, technology enabled exploration. Numbers and masses of vehicles required are greatly reduced, yet enable the pursuit of a broader range of objectives. The scope of missions addressed range from the assembly and maintenance of arrays of telescopes for emplacement at the Earth-Sun L2, to Human missions to asteroids, the moon and Mars. Vehicle designs are developed for proof of concept, to validate mission approaches and understand the value of new technologies. The stepping stone approach employs an incremental buildup of capabilities; allowing for decision points on exploration objectives. It enables testing of technologies to achieve greater reliability and understanding of costs for the next steps in exploration.

Cooke, Douglas R.↗

Operability on the Europa Clipper Mission: Challenges and Opportunities

Flight and ground system operability has been a focus area on the Europa Clipper Project since early in its formulation phase. This has given the operations team the opportunity to influence the design, with a goal of increasing overall system operability. This paper presents example operability challenges, opportunities, and solutions arising from the pre-Critical Design Review (CDR) system design. The integrated wing assembly design directly couples a scientific instrument (the REASON sounding radar) to the spacecraft’s power source (solar array wing panels). Impacts to mission operations of this design include: increased slew durations; solar array pointing constraints during inner cruise, Europa flybys, and orbit trim maneuvers; and stray light intrusions into the stellar reference units’ keep out zones. The use of CCSDS File Delivery Protocol (CFDP) Class-2 for reliable downlink of the large volume of Europa Clipper science data is described, along with nominal and off-nominal use cases. The effort to improve post-launch spacecraft visibility by adding a third low-gain antenna to the spacecraft is detailed. The design of the bulk data store has necessitated the implementation of accountable data products (ADPs), accountability identifiers (AIDs), and metadata packets to provide end-to-end science data accountability. To streamline and automate the flight rules generation and checking process, a first order and temporal logic-based solution of expressing flight rules without ambiguity, and whose programmatic implementation can be automated, is proposed. The focus on operability has had a positive influence on Europa Clipper design decisions, although cost, schedule, budget, heritage, and other technical concerns have many times outweighed operability concerns. However, experience to date demonstrates that this approach to operability results in more thorough, balanced consideration of the effect of early design trades and decisions on the operations phase of a mission than seen in many previous missions, and provides operations development insight into prioritizing work to go.

Signorelli, Joel↗

Operability on the Europa Clipper Mission: Challenges and Opportunities

Flight and ground system operability has been a focus area on the Europa Clipper Project since early in its formulation phase. This has given the operations team the opportunity to influence the design, with a goal of increasing overall system operability. This paper presents example operability challenges, opportunities, and solutions arising from the Critical Design Review (CDR) system design. The integrated wing assembly design directly couples a scientific instrument (the REASON sounding radar) to the spacecraft’s power source (solar array wing panels). Impacts to mission operations of this design include: increased slew durations; solar array pointing constraints during inner cruise, Europa flybys, and orbit trim maneuvers; and stray light intrusions into the stellar reference units’ keep out zones. The use of CCSDS File Delivery Protocol (CFDP) Class-2 for reliable downlink of the large volume of Europa Clipper science data is described, along with nominal and off-nominal use cases. The effort to improve post-launch spacecraft visibility by adding a third low-gain antenna to the spacecraft is detailed. The design of the bulk data store has necessitated the implementation of accountable data products (ADPs), accountability identifiers (AIDs), and metadata packets to provide end-to-end science data accountability. To streamline and automate the flight rules generation and checking process, a first order and temporal logic-based solution of expressing flight rules without ambiguity, and whose programmatic implementation can be automated, is proposed. The focus on operability has had a positive influence on Europa Clipper design decisions, although cost, schedule, budget, heritage, and other technical concerns have many times outweighed operability concerns. However, experience to date demonstrates that this approach to operability results in more thorough, balanced consideration of the effect of early design trades and decisions on the operations phase of a mission than seen in many previous missions, and provides operations development insight into prioritizing work to go.

Kumar, Meghana↗

Overview of the Plutonium-238 Supply Program's CERMET Production Target

The Plutonium-238 Supply Program is tasked with establishing a reliable domestic supply of 238Pu to fuel radioisotope thermal generators in its crucial role of supporting future space exploitation. To meet this need, researchers at Oak Ridge National Laboratory developed a robust production target design that is used to irradiate neptunium–aluminum cermet pellets to transmute the feedstock into usable 238Pu. This paper describes the target design and the innovative design features employed to improve target fabrication and assembly.

Howard, Richard↗

Developing Decommissioning Cost Estimating Relationships and the Decommissioning Estimate Analysis Library Estimating System - 20423

DOE-EM's Consolidated Business Center (EM-CBC) Office of Cost Estimating has developed a system of Decommissioning Cost Estimating Relationships (CERs) and Models to improve the reliability and efficiency of its estimates. The development builds on the multi-year process of collecting and organizing historical cost data from DOEEMs decommissioning projects and estimate model development to support project and program-level decommissioning estimates. The latest work has extended these models down to project scope element and component building area levels, allowing the actual costs of work for these estimate components to be assembled into estimates that reflect specific projects. The CERs have been incorporated into two estimator-friendly products - as cost libraries in the MII estimating program and as an MS Excel-based model, and are available for DOE federal staff use. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The LSLE echocardiograph - Commercial hardware aboard Spacelab

The Life Sciences Laboratory Equipment Echocardiograph, a commercial 77020AC Ultrasound Imaging System modified to meet NASA's spacecraft standards, is described. The assembly consists of four models: display and control, scanner, scan converter, and physioamplifiers. Four separate processors communicate over an IEE-488 bus, and the system has more than 6000 individual components on 35 printed circuit cards. Three levels of self test are provided: a short test during power up, a basic test initiated by a front panel switch, and interactive tests for specific routines. Default mode operation further enhances reliability. Modifications of the original system include the replacement of ac power supplies with dc to dc converters, a slide-out keyboard (to prevent accidental operation), Teflon insulated wire, and additional shielding for the ultrasound transducer cable.

Schwarz, R.↗

In-space construction and dynamics of large space structures

The types of equipment and structures that will be required to construct very large spacecraft in space are discussed. One of the basic issues that must be resolved is the appropriate mix of humans and machines in the construction process. While the use of robots offers the potential for reducing the number of extra-vehicular activity (EVA) hours required for particular construction operations, the availability of humans greatly increases the reliability of complex construction tasks. A hybrid system is described which makes the best use of man and machine to provide a highly reliable and versatile construction approach. Such a system will provide an efficient method for constructing large spacecraft until fully automated, robotic devices can be perfected. Details are given on an extensive ground test program which was designed to evaluate and demonstrate large spacecraft construction. A discussion is presented on the use of the Space Station Freedom, or an appropriate derivative, as a construction facility. Finally, a construction scenario and assembly timelines are presented for constructing a 20-meter-diameter high precision reflector.

Mikulas, Martin M., Jr.↗

Model based estimation of image depth and displacement

Passive depth and displacement map determinations have become an important part of computer vision processing. Applications that make use of this type of information include autonomous navigation, robotic assembly, image sequence compression, structure identification, and 3-D motion estimation. With the reliance of such systems on visual image characteristics, a need to overcome image degradations, such as random image-capture noise, motion, and quantization effects, is clearly necessary. Many depth and displacement estimation algorithms also introduce additional distortions due to the gradient operations performed on the noisy intensity images. These degradations can limit the accuracy and reliability of the displacement or depth information extracted from such sequences. Recognizing the previously stated conditions, a new method to model and estimate a restored depth or displacement field is presented. Once a model has been established, the field can be filtered using currently established multidimensional algorithms. In particular, the reduced order model Kalman filter (ROMKF), which has been shown to be an effective tool in the reduction of image intensity distortions, was applied to the computed displacement fields. Results of the application of this model show significant improvements on the restored field. Previous attempts at restoring the depth or displacement fields assumed homogeneous characteristics which resulted in the smoothing of discontinuities. In these situations, edges were lost. An adaptive model parameter selection method is provided that maintains sharp edge boundaries in the restored field. This has been successfully applied to images representative of robotic scenarios. In order to accommodate image sequences, the standard 2-D ROMKF model is extended into 3-D by the incorporation of a deterministic component based on previously restored fields. The inclusion of past depth and displacement fields allows a means of incorporating the temporal information into the restoration process. A summary on the conditions that indicate which type of filtering should be applied to a field is provided.

Damour, Kevin T.↗

Diagnostic for Plasma Enhanced Chemical Vapor Deposition and Etch Systems

In order to meet NASA's requirements for the rapid development and validation of future generation electronic devices as well as associated materials and processes, enabling technologies ion the processing of semiconductor materials arising from understanding etch chemistries are being developed through a research collaboration between Stanford University and NASA-Ames Research Center, Although a great deal of laboratory-scale research has been performed on many of materials processing plasmas, little is known about the gas-phase and surface chemical reactions that are critical in many etch and deposition processes, and how these reactions are influenced by the variation in operating conditions. In addition, many plasma-based processes suffer from stability and reliability problems leading to a compromise in performance and a potentially increased cost for the semiconductor manufacturing industry. Such a lack of understanding has hindered the development of process models that can aid in the scaling and improvement of plasma etch and deposition systems. The research described involves the study of plasmas used in semiconductor processes. An inductively coupled plasma (ICP) source in place of the standard upper electrode assembly of the Gaseous Electronics Conference (GEC) radio-frequency (RF) Reference Cell is used to investigate the discharge characteristics and chemistries. This ICP source generates plasmas with higher electron densities (approximately 10(exp 12)/cu cm) and lower operating pressures (approximately 7 mTorr) than obtainable with the original parallel-plate version of the GEC Cell. This expanded operating regime is more relevant to new generations of industrial plasma systems being used by the microelectronics industry. The motivation for this study is to develop an understanding of the physical phenomena involved in plasma processing and to measure much needed fundamental parameters, such as gas-phase and surface reaction rates. species concentration, temperature, ion energy distribution, and electron number density. A wide variety of diagnostic techniques are under development through this consortium grant to measure these parameters. including molecular beam mass spectrometry (MBMS). Fourier transform infrared (FTIR) spectroscopy, broadband ultraviolet (UV) absorption spectroscopy, a compensated Langmuir probe. Additional diagnostics. Such as microwave interferometry and microwave absorption for measurements of plasma density and radical concentrations are also planned.

Cappelli, Mark A.↗

Human Rating the Orion Parachute System

Human rating begins with design. Converging on the requirements and identifying the risks as early as possible in the design process is essential. Understanding of the interaction between the recovery system and the spacecraft will in large part dictate the achievable reliability of the final design. Component and complete system full-scale flight testing is critical to assure a realistic evaluation of the performance and reliability of the parachute system. However, because testing is so often difficult and expensive, comprehensive analysis of test results and correlation to accurate modeling completes the human rating process. The National Aeronautics and Space Administration (NASA) Orion program uses parachutes to stabilize and decelerate the Crew Exploration Vehicle (CEV) spacecraft during subsonic flight in order to deliver a safe water landing. This paper describes the approach that CEV Parachute Assembly System (CPAS) will take to human rate the parachute recovery system for the CEV.

Machin, Ricardo A.↗

Reliable and Efficient Electrochemical Recovery of O 2 from Metabolic CO 2 at the International Space Station (ISS)

Maximum O 2 recovery from metabolic carbon dioxide (CO 2 ) is desired for future long-duration missions beyond Low Earth Orbit (LEO). The O 2 recovery for the Environmental Control and Life Support System (ECLSS) at the International Space Station (ISS), presently limited to 50% (Sabatier), must be highly reliable and efficient and recover a minimum of 75% oxygen (O 2 ) from metabolic CO 2 . An alternative technology development effort currently underway at NASA Marshall Space Flight Center (MSFC) via a Microfluidic Electrochemical Reactor (MFECR) approach has the potential to increase O 2 recovery significantly and reduce the complexity of the ECLSS O 2 recovery at the ISS as it would replace three pieces, the CO 2 Reduction Assembly (CRA) (Sabatier reactor), the Oxygen Generation Assembly (OGA), and the Plasma Pyrolysis Assembly (PPA). The MFECR's electrochemical process generates ethylene (C 2 H 4 ) and carbon moxide (CO) instead of methane (CH 4 ) (Sabatier) as a byproduct, eliminating the need for further dehydrogenation through the PPA. As in the OGA, the MFECR's electrochemical process generates O 2 and hydrogen (H 2 ) from the water electrolysis process. MSFC and the University of Texas in Arlington (UTA) have jointly designed and fabricated an MFECR's single cell that operates at ambient conditions and utilizes a proprietary catalysis highly selective on reducing CO 2 to C 2 H 4 and CO at the cathode. This MFECR's single cell consists of gas diffusion layers at the cathode and anode for respective intake of CO 2 and output of O 2 from the catalytic layer. This approach is expected to substantially improve the ISS ECLSS sustainability and reduce power and weight requirements as the MFECR would replace three units currently installed in the ISS. In this paper, the authors discuss the outcome of preliminary tests, the current development, and the evaluation efforts on different alternatives for the cathode and the anode configurations, the setup of the MFECR at an engineering development unit (EDU) scale, and the O 2 recovery performance, and evaluation efforts on different alternatives on not only the configuration and setup of the MFECR at an Engineering Design Unit (EDU) scale but also the selection of component materials.

Jesus A Dominguez↗

Comparison of Accelerated Testing with Modeling to Predict Lifetime of CPV Solder Layers (Presentation)

Concentrating photovoltaic (CPV) cell assemblies can fail due to thermomechanical fatigue in the die-attach layer. In this presentation, we show the latest results from our computational model of thermomechanical fatigue. The model is used to estimate the relative lifetime of cell assemblies exposed to various temperature histories consistent with service and with accelerated testing. We alsopresent early results from thermal cycling experiments designed to help validate the computational model.

14 SOLAR ENERGY↗

Single Ion Implantation and Deterministic Doping

The presence of single atoms, e.g. dopant atoms, in sub-100 nm scale electronic devices can affect the device characteristics, such as the threshold voltage of transistors, or the sub-threshold currents. Fluctuations of the number of dopant atoms thus poses a complication for transistor scaling. In a complementary view, new opportunities emerge when novel functionality can be implemented in devices deterministically doped with single atoms. The grand price of the latter might be a large scale quantum computer, where quantum bits (qubits) are encoded e.g. in the spin states of electrons and nuclei of single dopant atoms in silicon, or in color centers in diamond. Both the possible detrimental effects of dopant fluctuations and single atom device ideas motivate the development of reliable single atom doping techniques which are the subject of this chapter. Single atom doping can be approached with top down and bottom up techniques. Top down refers to the placement of dopant atoms into a more or less structured matrix environment, like a transistor in silicon. Bottom up refers to approaches to introduce single dopant atoms during the growth of the host matrix e.g. by directed self-assembly and scanning probe assisted lithography. Bottom up approaches are discussed in Chapter XYZ. Since the late 1960's, ion implantation has been a widely used technique to introduce dopant atoms into silicon and other materials in order to modify their electronic properties. It works particularly well in silicon since the damage to the crystal lattice that is induced by ion implantation can be repaired by thermal annealing. In addition, the introduced dopant atoms can be incorporated with high efficiency into lattice position in the silicon host crystal which makes them electrically active. This is not the case for e.g. diamond, which makes ion implantation doping to engineer the electrical properties of diamond, especially for n-type doping much harder then for silicon. Ion implantation is usually a highly statistical process, where high fluences of energetic ions, ranging from {approx}10{sup 9} to >10{sup 16} cm{sup -2} are implanted. For single atom device development, control over the absolute number of ions is needed and ions have to be placed with high spatial resolution. In the following sections we will discuss a series of approaches to single ion implantation with regard to single ion impact sensing and control of single ion positioning.

77 NANOSCIENCE AND NANOTECHNOLOGY↗