Search NASA⌕ Search

SEARCH · Search NASA

Results for “flight data analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Poisson vs. Gaussian statistics for sparse X-ray data: Application to the soft X-ray spectrometer

Reliable results when fitting X-ray data require proper consideration of the statistics involved. We probe the impact of Gaussian versus Poisson statistics at low count levels using both the standard χ^(2) method and maximum likelihood based on Poisson (C) statistics. The difference is studied and quantified through simulated spectra with known properties. We then test the results through analysis of Mn Kα calibration data taken with the flight spare microcalorimeter for the Hitomi soft X-ray spectrometer. Through comparison with simulations, our results show that the χ^(2) method tends to give overly optimistic estimates of the detector energy resolution, in particular when there are few counts. Given an energy resolution of ∼5 eV and a line with about 100 photons, the line width becomes ∼10% lower in the χ^(2) method than in Poisson statistics. This is a consequence of the uncertainties being dominated by counting statistics, and therefore highlights the need to choose the appropriate fit statistic.

Shinya Yamada↗
NASA NTRS1991

Optical communication for space missions

Activities performed at NASA/GSFC (Goddard Space Flight Center) related to direct detection optical communications for space applications are discussed. The following subject areas are covered: (1) requirements for optical communication systems (data rates and channel quality; spatial acquisition; fine tracking and pointing; and transmit point-ahead correction); (2) component testing and development (laser diodes performance characterization and life testing; and laser diode power combining); (3) system development and simulations (The GSFC pointing, acquisition and tracking system; hardware description; preliminary performance analysis; and high data rate transmitter/receiver systems); and (4) proposed flight demonstration of optical communications.

Firtmaurice, M.↗
NASA NTRS2006

Adaptive Modeling, Engineering Analysis and Design of Advanced Aerospace Vehicles

This paper describes initial progress towards the development and enhancement of a set of software tools for rapid adaptive modeling, and conceptual design of advanced aerospace vehicle concepts. With demanding structural and aerodynamic performance requirements, these high fidelity geometry based modeling tools are essential for rapid and accurate engineering analysis at the early concept development stage. This adaptive modeling tool was used for generating vehicle parametric geometry, outer mold line and detailed internal structural layout of wing, fuselage, skin, spars, ribs, control surfaces, frames, bulkheads, floors, etc., that facilitated rapid finite element analysis, sizing study and weight optimization. The high quality outer mold line enabled rapid aerodynamic analysis in order to provide reliable design data at critical flight conditions. Example application for structural design of a conventional aircraft and a high altitude long endurance vehicle configuration are presented. This work was performed under the Conceptual Design Shop sub-project within the Efficient Aerodynamic Shape and Integration project, under the former Vehicle Systems Program. The project objective was to design and assess unconventional atmospheric vehicle concepts efficiently and confidently. The implementation may also dramatically facilitate physics-based systems analysis for the NASA Fundamental Aeronautics Mission. In addition to providing technology for design and development of unconventional aircraft, the techniques for generation of accurate geometry and internal sub-structure and the automated interface with the high fidelity analysis codes could also be applied towards the design of vehicles for the NASA Exploration and Space Science Mission projects.

Mukhopadhyay, Vivek↗
NASA NTRS2018

Changes in Exercise Data Management

The suite of exercise hardware aboard the International Space Station (ISS) generates an immense amount of data. The data collected, treadmill, cycle ergometer, and resistance strength training hardware, are basic exercise parameters (time, heart rate, speed, load, etc.). The raw data are processed in the laboratory and more detailed parameters are calculated from each exercise data file. Updates recently have been made to how these valuable data are stored, adding an additional level of security, increasing accessibility, and resulting in overall increased efficiency of medical report delivery. Questions regarding exercise performance or how exercise may influence other variables of crew health frequently arise within the crew health care community. Inquiries regarding the health of the exercise hardware often need quick analysis and response to ensure the exercise system is operable on a continuous basis. Consolidating all of the exercise system data in a single repository enables a quick response to both the medical and engineering communities. A SQL server database is currently in use, and provides a secure location for all of the exercise data starting at ISS Expedition 1 to current date. The database has been structured to update derived metrics automatically, making analysis and reporting available within minutes of dropping the in-flight data into the database. Commercial tools were evaluated to help aggregate and visualize data from the SQL database. The Tableau software provides manageable interface, which has improved the laboratory’s output time of crew reports by 67%. Expansion of the SQL database, to be inclusive of additional medical requirement metrics, addition of ‘app-like’ tools for mobile visualization, and collaborative use (e.g., operational support teams, research groups, and International Partners) of the data system, is currently being explored.

Buxton, R. E.↗
NASA NTRS2009

Pyroshock Simulation Systems: Are We Correctly Qualifying Flight Hardware for Pyroshock Environments?

There are several methods of shock testing that are commonly used by the aerospace industry to qualify flight hardware to pyroshock environments. In some cases the shock results and in particular the shock response spectra computed from these tests were interpreted in such a way as to satisfy the testing requirements and were often considered successful for flight hardware qualification. However, close scrutiny of these acquired shock data suggest gross violation of the pyroshock qualification requirements. There are several issues, both in terms of the shock generation mechanisms and the shock signature acquisition and analysis that have led to improper qualification of flight hardware. In this paper some factors contributing to the misinterpretation of the shock data are reviewed. First, issues with the hardware fixturing and instrumentation that may lead to incorrect shock testing are discussed. Second, issues facing the shock simulation systems and pyrotechnic testing are reviewed. Finally, issues pertaining to the data acquisition and analysis are briefly discussed.

instrumentation↗
NASA NTRS1972

Analysis of instrumentation error effects on the identification accuracy of aircraft parameters

An analytical investigation is presented of the effect of unmodeled measurement system errors on the accuracy of aircraft stability and control derivatives identified from flight test data. Such error sources include biases, scale factor errors, instrument position errors, misalignments, and instrument dynamics. Two techniques (ensemble analysis and simulated data analysis) are formulated to determine the quantitative variations to the identified parameters resulting from the unmodeled instrumentation errors. The parameter accuracy that would result from flight tests of the F-4C aircraft with typical quality instrumentation is determined using these techniques. It is shown that unmodeled instrument errors can greatly increase the uncertainty in the value of the identified parameters. General recommendations are made of procedures to be followed to insure that the measurement system associated with identifying stability and control derivatives from flight test provides sufficient accuracy.

Sorensen, J. A.↗
NASA NTRS1981

Measurement of HO2 and other trace gases in the stratosphere using a high resolution far infrared spectrometer at 28 Km

A progress report and data analyses from the December 1980 flight are presented. The following areas are covered: (1) computer analysis of the flight spectra to obtain phase corrected, normalized sums of spectra for retrieval of atmospheric profiles; (2) study of atmospheric HF, HCl, and H2O; (3) stratospheric H2O2 and HOCl; (4) laboratory spectroscopy of HOCl; and (5) design study of a new balloon gondola. The majority of the flight data were taken in the low background mode, i.e., one input to the spectrometer looking at the sky and the other looking at a LN2 temperature blackbody. An analysis of HF stratospheric measurements was undertaken in conjunction with the HF analysis. High quality spectra showing the HOCl q-branches under optically thin conditions were also obtained.

Traub, W. A.↗
NASA NTRS1992

Flight-determined stability analysis of multiple-input-multiple-output control systems

Singular value analysis can give conservative stability margin results. Applying structure to the uncertainty can reduce this conservatism. This paper presents flight-determined stability margins for the X-29A lateral-directional, multiloop control system. These margins are compared with the predicted unscaled singular values and scaled structured singular values. The algorithm was further evaluated with flight data by changing the roll-rate-to-aileron-command-feedback gain by +/- 20 percent. Also presented are the minimum eigenvalues of the return difference matrix which bound the singular values. Extracting multiloop singular values from flight data and analyzing the feedback gain variations validates this technique as a measure of robustness. This analysis can be used for near-real-time flight monitoring and safety testing.

Burken, John J.↗
NASA NTRS1992

Flight-determined stability analysis of multiple-input-multiple-output control systems

Singular value analysis can give conservative stability margin results. Applying structure to the uncertainty can reduce this conservatism. This paper presents flight-determined stability margins for the X-29A lateral-directional, multiloop control system. These margins are compared with the predicted unscaled singular values and scaled structured singular values. The algorithm was further evaluated with flight data by changing the roll-rate-to-aileron command-feedback gain by +/- 20 percent. Minimum eigenvalues of the return difference matrix which bound the singular values are also presented. Extracting multiloop singular values from flight data and analyzing the feedback gain variations validates this technique as a measure of robustness. This analysis can be used for near-real-time flight monitoring and safety testing.

Burken, John J.↗
NASA NTRSDate not supplied

Determining Aircraft Moments of Inertia from Flight Test Data

Flight test maneuver design and dynamic modeling techniques were developed for determining aircraft moments of inertia from flight test data. Full nonlinear rigid-body rotational equations of motion were used in the analysis, with aerodynamic moment dependencies modeled by linear expansions in the aircraft states and controls. Aerodynamic parameters were estimated simultaneously with inertia parameters using equation-error modeling applied to flight test data from maneuvers designed specifically for this problem. The approach was demonstrated using a nonlinear F-16 simulation, then applied to a remotely-piloted subscale aircraft flight test. Errors in the aircraft moment of inertia parameters determined from simulated F-16 flight test maneuver data were less than 6 percent compared to the true values in the simulation. Flight test results for the subscale aircraft were within 6 percent of ground-test values obtained using the same aircraft.

moments of inertia↗
NASA NTRSDate not supplied

Determining Aircraft Moments of Inertia from Flight Test Data

Flight test maneuver design and dynamic modeling techniques were developed for determining aircraft moments of inertia from flight test data. Full nonlinear rigid-body rotational equations of motion were used in the analysis, with aerodynamic moment dependencies modeled by linear expansions in the aircraft states and controls. Aerodynamic parameters were estimated simultaneously with inertia parameters using equation-error modeling applied to flight test data from maneuvers designed specifically for this problem. The approach was demonstrated using a nonlinear F 16 simulation, then applied to a remotely piloted subscale aircraft flight test. Errors in the aircraft moment of inertia parameters determined from simulated F-16 flight test maneuver data were less than 6 percent compared to the true values in the simulation. Flight test results for the subscale aircraft were within 6 percent of ground-test values obtained using the same aircraft.

Aircraft Moments of Inertia↗
NASA NTRS2021

Determining Aircraft Moments of Inertia from Flight Test Data

Flight test maneuvers and dynamic modeling techniques were developed for determining aircraft moments of inertia from flight test data. Full nonlinear rigid-body rotational equations of motion were used in the analysis, with aerodynamic moment dependencies modeled by linear expansions in the aircraft states and controls. Aerodynamic parameters were estimated simultaneously with inertia parameters using equation-error modeling applied to flight test data from maneuvers designed specifically for this problem. The approach was demonstrated using a nonlinear F 16 simulation, then applied to a remotely-piloted subscale aircraft flight test. Errors in the aircraft moment of inertia parameters determined from simulated F-16 flight test data were less than 6 percent compared to the true values in the simulation. Flight test results for the subscale aircraft were within 6 percent of ground-test values obtained using the same aircraft.

Parameter estimation↗
NASA NTRS1977

A compilation of spacecraft loads data from four Titan Centaur Launch Vehicle flights. Volume 1: Acoustics data

The payloads carried by the first four Titan Centaur launch vehicle flights were, a Viking spacecraft dynamic simulator, the Helios A spacecraft, and the two Viking spacecraft. Dynamic loads data were accumulated from these four flights for application to the Viking spacecraft. The accoustics data include time histories and spectral analysis plots of accoustic pressure measurements made in the Centaur and payload compartment during launch flight. Summary plots are presented to show composite spectra for liftoff and Mach 1/Max Q periods of flight.

Kachadourian, G.↗
NASA NTRS1995

Determining the Accuracy of Aerodynamic Model Parameters Estimated from Flight Test Data

An important part of building mathematical models based on measured data is calculating the accuracy associated with statistical estimates of the model parameters. Indeed, without some idea of this accuracy, the parameter estimates themselves have limited value. In this work, an expression for computing quantitatively correct parameter accuracy measures for maximum likelihood parameter estimates with colored residuals is developed and validated. This result is important because experience in analyzing flight test data reveals that the output residuals from maximum likelihood estimation are almost always colored. The calculations involved can be appended to conventional maximum likelihood estimation algorithms. Monte Carlo simulation runs were used to show that parameter accuracy measures from the new technique accurately reflect the quality of the parameter estimates from maximum likelihood estimation without the need for correction factors or frequency domain analysis of the output residuals. The technique was applied to flight test data from repeated maneuvers flown on the F-18 High Alpha Research Vehicle (HARV). As in the simulated cases, parameter accuracy measures from the new technique were in agreement with the scatter in the parameter estimates from repeated maneuvers, while conventional parameter accuracy measures were optimistic.

Morelli, Eugene A.↗
NASA NTRS1997

Accuracy of Aerodynamic Model Parameters Estimated from Flight Test Data

An important put of building mathematical models based on measured date is calculating the accuracy associated with statistical estimates of the model parameters. Indeed, without some idea of this accuracy, the parameter estimates themselves have limited value. An expression is developed for computing quantitatively correct parameter accuracy measures for maximum likelihood parameter estimates when the output residuals are colored. This result is important because experience in analyzing flight test data reveals that the output residuals from maximum likelihood estimation are almost always colored. The calculations involved can be appended to conventional maximum likelihood estimation algorithms. Monte Carlo simulation runs were used to show that parameter accuracy measures from the new technique accurately reflect the quality of the parameter estimates from maximum likelihood estimation without the need for correction factors or frequency domain analysis of the output residuals. The technique was applied to flight test data from repeated maneuvers flown on the F-18 High Alpha Research Vehicle. As in the simulated cases, parameter accuracy measures from the new technique were in agreement with the scatter in the parameter estimates from repeated maneuvers, whereas conventional parameter accuracy measures were optimistic.

Morelli, Eugene A.↗
NASA NTRS2015

Update of Bisphosphonate Flight Experiment

Elevated bone resorption is a hallmark of human spaceflight and bed rest indicating that elevated remodeling is a major factor in the etiology of space flight bone loss. In a collaborative effort between the NASA and JAXA space agencies, we are testing whether an antiresorptive drug would provide additional benefit to in-flight exercise to ameliorate bone loss and hypercalciuria during long-duration spaceflight. Measurements of bone loss include DXA, QCT, pQCT, urinary and blood biomarkers. We have completed analysis of R+1year data from 7 crewmembers treated with alendronate during flight, as well as immediate post flight (R+<2wks) data from 6 of 10 concurrent controls without treatment. The treated astronauts used the Advanced Resistive Exercise Device (ARED) during their missions. The purpose of this report is twofold: 1) to report the results of inflight, post flight and one year post flight bone measures compared with available controls with and without the use of ARED; and 2) to discuss preliminary data on concurrent controls. The figure below compares the BMD changes in ISS crewmembers exercising with and without the current ARED protocol and the alendronate treated crewmembers also using the ARED. This shows that the use of ARED prevents about half the bone loss seen in early ISS crewmembers and that the addition of an antiresorptive provides additional benefit. Resorption markers and urinary Ca excretion are not impacted by exercise alone but are significantly reduced with antiresorptive treatment. Bone measures for treated subjects, 1 year after return from space remain at or near baseline. DXA data for the 6 concurrent controls using the ARED device are similar to DXA data shown in the figure below. QCT data for these six indicate that the integral data are consistent with the DXA data, i.e., comparing the two control groups suggests significant but incomplete improvement in maintaining BMD using the ARED protocol. Biochemical data of the concurrent control group await sample return and analysis. The preliminary conclusion is that an antiresorptive may be an effective adjunct to exercise during long-duration spaceflight.

LeBlanc, A.↗
NASA NTRSDate not supplied

Laser Communications Relay Demonstration Optimetrics Experiment

Within this paper, we report on an Optimetrics experiment conducted on the National Aeronautics and Space Administration (NASA) Laser Communication Relay Demonstration (LCRD). The high precision two-way ranging is conducted on the optical communications link between the LCRD space terminal in a geosynchronous orbit and the Optical Ground Station 1 (OGS1) at Table Mountain, California, and is referred to as optimetrics ranging. The receiver to transmitter clock loopback is implemented in the LCRD space modem. A digital dual mixer time difference phase meter (DDMTD) is implemented in the OGS1 ground modem. The round-trip time is measured with the DDMTD by counting the frame and data clock ticks between transmitter and receiver frame synchronization markers for coarse range, and the relative phase of the transmit and receive clock for high precision range. This approach provides coverage for all potential ranges with no ranging ambiguity. The flight modem FPGA code was modified for frame and data clock loopback and the OGS1 FPGA code was modified for the DDMTD phase meter implementation. The experiment team conducted a 36-hour continuous ranging measurement. Preliminary two-way optimetrics ranging data show a noise floor of 3cm (rms). Based on our theoretical noise analysis and ground tests with spare flight modems, we expected one order of magnitude improvement on ranging precision. We are conducting detailed post data processing to identify the differences to further reduce the noise level and formulating an improved implementation approach for future missions. For reference and comparison, traditional Radio Frequency (RF) ranging between LCRD and OGS1 was conducted at the same time and indicates a ranging noise floor of 30cm(rms). Other telemetry and relevant environmental parameters such as weather and atmosphere temperature were also collected for offline data processing. The high precision ranging and range rate measurements from the laser communications data link clock and clock phase are performed simultaneously with continuous optical communication. No extra hardware added to existing system. This high precision optimetrics measurement implementation provides alternative ranging and range rate measurements for orbit determination (OD) and flight dynamics calculations with higher precision. We see significant improvement on OD for navigation upon implementation in future optical communication systems.

Rafael Garcia↗
NASA NTRS1981

Comparison of forward fuselage to Space Shuttle Orbiter flight pressure data to wind tunnel and analytical results in the hypersonic Mach number range

The Space Transportation System (STS) test program is unique in that it combines flight testing with operational flights using the first operational orbital vehicle (OV-102). The Space Shuttle Orbiter was instrumented to obtain various types of flight data. The instrumentation, designated Development Flight Instrumentation (DFI) includes pressure transducers, thermocouples, calorimeters, and accelerometers. A comparison is conducted between orbiter DFI forward fuselage flight pressure data obtained from OV-102 during the STS-1 reentry, and ground facility data obtained utilizing a 0.04 scale Orbiter forebody model. The comparisons are used to validate the existing experimental data base, optimize the pressure modeling technique, and make possible the refinement of error analysis relative to both. The obtained results indicate, in general, good agreement between flight and ground-based data.

Bradley, P. F.↗