Results for “graphitic structures” — Page 54

NASA NTRS1999

Thermographic Testing Using on the X-33 Space Launch Vehicle Program by BFGoodrich Aerospace

The X-33 program is a team effort sponsored by NASA, under Cooperative Agreement NCC8-115, and led by the Lockheed Martin Corporation. Team member BFGoodrich Aerospace Aerostructures Group (formerly Rohr) is responsible for design, manufacture, and integration of the Thermal Protection System (TPS) of the X-33 launch vehicle. The X-33 is a half-scale, experimental prototype of a vehicle called RLV (Reusable Launch Vehicle) or VentureStar(Trademark), an SSTO (single stage to orbit) vehicle, which is a proposed successor to the aging Space Shuttle. Thermographic testing has been employed by BFGoodrich Aerospace Aerostructures Group for a wide variety of uses in the testing of components of the X-33. Thermographic NDT (TNDT) has been used for inspecting large graphite-epoxy/aluminum honeycomb sandwich panels used on the Leeward Aeroshell structure of the X-33. And TNDT is being evaluated for use in inspecting carbon-carbon composite parts such as the nosecap and wing leading edge components. Pulsed Infrared Testing (PIRT), a special form of TNDT, is used for the routine inspection of sandwich panels made of brazed inconel honeycomb and facesheets. In the developmental and qualification testing of sub-elements of the X-33, thermography has been used to monitor 1) Arc Jet tests at NASA Ames Research Center in Mountainview, CA and NASA Johnson Space Center in Houston, TX, 2) High Temperature (wind) Tunnel Tests (HTT) at NASA Langley Research Center in Langley, VA, and 3) Hot Gas Tests at NASA Marshall Space Flight Center in Huntsville, AL.

Burleigh, Douglas↗

NASA NTRS2017

A Cryogenic Thermal Source for Detector Array Characterization

We describe the design, fabrication, and validation of a cryogenically compatible quasioptical thermal source for characterization of detector arrays. The source is constructed using a graphite-loaded epoxy mixture that is molded into a tiled pyramidal structure. The mold is fabricated using a hardened steel template produced via a wire electron discharge machining process. The absorptive mixture is bonded to a copper backplate enabling thermalization of the entire structure and measurement of the source temperature. Measurements indicate that the reflectance of the source is less than 0.001 across a spectral band extending from 75 to 330 gigahertz.

Chuss, David T.↗

DOE OSTI2020

Technical Program Plan for INL Advanced Reactor Technologies Advanced Gas Reactor Fuel Development and Qualification Program

High-temperature gas cooled reactors (HTGRs) are graphite moderated nuclear reactors cooled with helium. Their high outlet temperatures and thermal energy conversion efficiency enable efficient and cost effective integration with non electricity generating applications. These applications include process heat and hydrogen production for petrochemical and other industrial processes that require operating temperatures between 300 and 900°C. HTGRs will supplement the use of premium fossil fuels such as oil and natural gas, improve overall energy security in the United States by reducing dependence on foreign fuels, and reduce carbon dioxide (CO2)/greenhouse gas emissions. The HTGR design uses helium as a coolant, graphite as a neutron moderator, and ceramic particle fuel. Helium is chemically inert and neutronically transparent. The graphite core slows down the neutrons, retains its strength at high temperatures, provides structural stability, and acts as a substantial heat sink during transient conditions. The ceramic particle fuel is extremely robust and retains the radioactive by products of the fission reaction within the coated particle under normal and off normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2019

Technical Program Plan for INL Advanced Reactor Technologies Advanced Gas Reactor Fuel Development and Qualification Program

High-temperature gas cooled reactors (HTGRs) are graphite moderated nuclear reactors cooled with helium. Their high outlet temperatures and thermal energy conversion efficiency enable efficient and cost effective integration with non electricity generating applications. These applications include process heat and hydrogen production for petrochemical and other industrial processes that require operating temperatures between 300 and 900°C. HTGRs will supplement the use of premium fossil fuels such as oil and natural gas, improve overall energy security in the United States by reducing dependence on foreign fuels, and reduce carbon dioxide (CO2)/greenhouse gas emissions. The HTGR design uses helium as a coolant, graphite as a neutron moderator, and ceramic particle fuel. Helium is chemically inert and neutronically transparent. The graphite core slows down the neutrons, retains its strength at high temperatures, provides structural stability, and acts as a substantial heat sink during transient conditions. The ceramic particle fuel is extremely robust and retains the radioactive by products of the fission reaction within the coated particle under normal and off normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Technical Program Plan for INL Advanced Reactor Technologies Advanced Gas Reactor Fuel Development and Qualification Program

High-temperature gas cooled reactors (HTGRs) are graphite moderated nuclear reactors cooled with helium. Their high outlet temperatures and thermal energy conversion efficiency enable efficient and cost effective integration with non electricity generating applications. These applications include process heat and hydrogen production for petrochemical and other industrial processes that require operating temperatures between 300 and 900°C. HTGRs will supplement the use of premium fossil fuels such as oil and natural gas, improve overall energy security in the United States by reducing dependence on foreign fuels, and reduce carbon dioxide (CO2)/greenhouse gas emissions. The HTGR design uses helium as a coolant, graphite as a neutron moderator, and ceramic particle fuel. Helium is chemically inert and neutronically transparent. The graphite core slows down the neutrons, retains its strength at high temperatures, provides structural stability, and acts as a substantial heat sink during transient conditions. The ceramic particle fuel is extremely robust and retains the radioactive by products of the fission reaction within the coated particle under normal and off normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Technical Program Plan for INL Advanced Reactor Technologies Advanced Gas Reactor Fuel Development and Qualification Program

High-temperature gas cooled reactors (HTGRs) are graphite moderated nuclear reactors cooled with helium. Their high outlet temperatures and thermal energy conversion efficiency enable efficient and cost effective integration with non electricity generating applications. These applications include process heat and hydrogen production for petrochemical and other industrial processes that require operating temperatures between 300 and 900°C. HTGRs will supplement the use of premium fossil fuels such as oil and natural gas, improve overall energy security in the United States by reducing dependence on foreign fuels, and reduce carbon dioxide (CO2)/greenhouse gas emissions. The HTGR design uses helium as a coolant, graphite as a neutron moderator, and ceramic particle fuel. Helium is chemically inert and neutronically transparent. The graphite core slows down the neutrons, retains its strength at high temperatures, provides structural stability, and acts as a substantial heat sink during transient conditions. The ceramic particle fuel is extremely robust and retains the radioactive by products of the fission reaction within the coated particle under normal and off normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1996

Fabrication of Iron-Containing Carbon Materials From Graphite Fluoride

Carbon materials containing iron alloy, iron metal, iron oxide or iron halide were fabricated. Typical samples of these metals were estimated to contain 1 iron atom per 3.5 to 5 carbon atoms. Those carbon materials containing iron alloy, iron metal, and/or Fe3O4 were magnetic. The kinetics of the fabrication process were studied by exposing graphite fluoride (CF(0.68)) to FeCl3 over a 280 to 420 C temperature range. Between 280 and 295 C, FeCl3 quickly entered the structure of CF(0.68), broke the carbon-fluorine bonds, and within 10 to 30 min, completely converted it to carbon made up of graphite planes between which particles of crystalline FeF3 and noncrystalline FeCl3 were located. Longer reaction times (e.g., 28 hr) or higher reaction temperatures (e.g., 420 C) produced materials containing graphite, a FeCl3-graphite intercalation compound, FeCl2(center dot)4H2O, and FeCl2(center dot)2H2O. These products were further heat treated to produce iron-containing carbon materials. When the heating temperature was kept in the 750 to 850 C range, and the oxygen supply was kept at the optimum level, the iron halides in the carbon structure were converted to iron oxides. Raising the heat to temperatures higher than 900 C reduced such iron oxides to iron metal. The kinetics of these reactions were used to suggest processes for fabricating carbon materials containing iron alloy. Such processes were then tested experimentally. In one of the successful trial runs, commercially purchased CF(0.7) powder was used as the reactant, and NiO was added during the final heating to 1200 C as a source of both nickel and oxygen. The product thus obtained was magnetic and was confirmed to be a nickel-iron alloy in carbon.

Hung, Ching-cheh↗

NASA NTRS1992

Structural studies of two aerobrake heatshield panel concepts

Structural sizing and performance data are presented for two different aerobrake hexagonal heatshield panel structural concepts. One concept features a sandwich construction with an aluminum honeycomb core and thin quasi-isotropic graphite-epoxy face sheets. The other concept features a skin-rib isogrid construction with thin quasi-isotropic graphite-epoxy skins, and graphite-epoxy ribs oriented at 0, +60, and -60 deg along the panel. Linear static, linear bifurcation buckling, and nonlinear static analyses were performed to compare the structural performance of the two panel concepts and assess their feasibility for a Lunar Transfer Vehicle aerobrake application.

Dorsey, John T.↗

NASA NTRS1980

Impact-initiated damage thresholds in composites

An experimental investigation was conducted to study the effect of low velocity projectile impact on the sandwich-type structural components. The materials used in the fabrication of the impact surface were graphite-, Kevlar-, and boron-fibers with appropriate epoxy matrices. The testing of the specimens was performed at moderately low- and high-temperatures as well as at room temperature to assess the impact-initiated strength degradation of the laminates. Eleven laminates with different stacking sequences, orientations, and thicknesses were tested. The low energy projectile impact is considered to simulate the damage caused by runway debris, dropping of the hand tools during servicing, etc., on the secondary aircraft structures fabricated with the composite materials. The results show the preload and the impact energy combinations necessary to cause catastrophic failures in the laminates tested. A set of faired curves indicating the failure thresholds is shown separately for the tension- and compression-loaded laminates. The specific-strengths and -moduli for the various laminates tested are also given.

Sharma, A. V.↗

NASA NTRS1979

HiMAT structural development design methodology

In order to improve aerodynamic performance, a twist criterion was used to design the canard and wing lifting surfaces of two graphite-epoxy research aircraft. To meet that twist criterion, the lifting surfaces were tailored using graphite-epoxy tape. The outer surface of the aircraft is essentially constructed of 95 percent graphite epoxy materials. The analytical tools and methodology used to design those lifting surfaces are described. One aircraft was subjected to an 8g ground test in order to verify structural integrity and to determine how well the desired twist was achieved. Test results are presented and the reductions of both flight and ground strain test gages and their associated stresses are discussed.

Price, M. A.↗

DOE OSTI2013

Effects of high energy Au-ion irradiation on the microstructure of diamond films

The effects of 2.245 GeV Au-ion irradiation and subsequent annealing processes on the evolution of microstructure of diamond films with microcrystalline (MCD) or ultra-nanocrystalline (UNCD) granular structure were investigated, using near edge x-ray absorption fine structure and electron energy loss spectroscopy in transmission electron microscopy. For MCD films, the Au-ion irradiation disintegrated some of the diamond grains, resulting in the formation of nano-sized carbon clusters embedded in a matrix of amorphous carbon (a-C). The annealing process recrystallized the diamond grains and converted the a-C into nano-sized graphite particulates and, at the same time, induced the formation of nano-sized i-carbon clusters, the bcc structured carbon with a{sub 0} = 0.432 nm. In contrast, for UNCD films, the Au-ion irradiation transformed the grain boundary phase into nano-sized graphite, but insignificantly altered the crystallinity of the grains of the UNCD films. The annealing process recrystallized the materials. In some of the regions, the residual a-C phases were transformed into nano-sized graphites, whereas in other regions i-carbon nanoclusters were formed. The difference in irradiation-induced microstructural transformation behavior between the MCD and the UNCD films is ascribed to the different granular structures of the two types of films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1990

Nature and origin of interstellar diamond from the Allende CV3 meteorite

Data and experimental evidence which support the contention that the C delta diamonds may result from grain-grain collisions in supernova shocks in the interstellar medium are presented. Fragments of the Allende CV3 chondrite were acid-treated. A whitish powder was obtained. For the Analytical Electron Microscopy (AEM) a small drop of ethanol suspension was transferred onto holey carbon support films on 3 mm EM grids. The AEM was performed on transmission-thin fragments of the material which overlay holes in the film, to eliminate interference from the substrate. Electron Spectroscopy for Chemical Analysis (ESCA) was performed on a large aliquot of C. Diamond was identified by selected area electron diffraction. Scanning Transmission Electron Microscope / Energy Dispersive X-ray (STEM-EDS) microanalyses of the C delta diamond, using a light-element detector, show that oxygen and possibly nitrogen are the only impurities consistently present. ESCA spectra from bulk C delta material confirm the presence of N at a level of 0.35 percent or less. Under UV irradiation a yellow-red fluorescence is observed, consistent with that of natural diamonds containing substitutional N. Electron Energy Loss Spectra (EELS) were recorded at 2 eV resolution from the C delta diamond, high pressure synthetic diamond, a diamond film produced in a low pressure plasma by chemical vapor deposition (CVD) on a heated silicon substrate (Roy, 1987), graphite, and amorphous arc sputtered carbon. Comparison of the carbon K edge shape and fine structure shows the Allende C delta phase to be largely diamond, but with a significant pre-edge absorption feature indicative of transitions of C 1s electrons into pi asterisk orbitals which are absent in the purely sp(3)-bonded diamond but present in graphite and amorphous carbon.

Blake, David↗

DOE OSTI2018

Technical Program Plan for INL Advanced Reactor Technologies Advanced Gas Reactor Fuel Development and Qualification Program

High-temperature gas cooled reactors (HTGRs) are graphite moderated nuclear reactors cooled with helium. Their high outlet temperatures and thermal energy conversion efficiency enable efficient and cost effective integration with non electricity generating applications. These applications include process heat and hydrogen production for petrochemical and other industrial processes that require operating temperatures between 300 and 900°C. HTGRs will supplement the use of premium fossil fuels such as oil and natural gas, improve overall energy security in the United States by reducing dependence on foreign fuels, and reduce carbon dioxide (CO2)/greenhouse gas emissions. The HTGR design uses helium as a coolant, graphite as a neutron moderator, and ceramic particle fuel. Helium is chemically inert and neutronically transparent. The graphite core slows down the neutrons, retains its strength at high temperatures, provides structural stability, and acts as a substantial heat sink during transient conditions. The ceramic particle fuel is extremely robust and retains the radioactive by products of the fission reaction within the coated particle under normal and off normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1992

Experimental and analytical study of the effects of floor location on response of composite fuselage frames

Experimental and analytical results are presented of the effects of floor placement on the structural response and strength of I-cross section, semi-circular fuselage frames constructed of graphite-epoxy composite material. The composite frame configuration is representative of current conventional aircraft design. Experimental strain distributions are presented from static loading tests of the composite frames and compared with finite element structural models and closed form solutions. An understanding of floor location effects can aid dynamists in predicting the crash behavior of these conventional structures, and may assist the designer in developing crashworthy structures for future aircraft.

Jones, Lisa E.↗

DOE OSTI2018

Resolving the Chemically Discrete Structure of Synthetic Borophene Polymorphs

Atomically thin two-dimensional (2D) materials exhibit superlative properties dictated by their intralayer atomic structure, which is typically derived from a limited number of thermodynamically stable bulk layered crystals (e.g., graphene from graphite). The growth of entirely synthetic 2D crystals, those with no corresponding bulk allotrope, would circumvent this dependence upon bulk thermodynamics and substantially expand the phase space available for structure-property engineering of 2D materials. However, it remains unclear if synthetic 2D materials can exist as structurally and chemically distinct layers anchored by van der Waals (vdW) forces, as opposed to strongly bound adlayers. Here, we show that atomically thin sheets of boron (i.e., borophene) grown on the Ag(111) surface exhibit a vdW-like structure without a corresponding bulk allotrope. Using X-ray standing wave-excited X-ray photoelectron spectroscopy, the positions of boron in multiple chemical states are resolved with sub-angstrom spatial resolution, revealing that the borophene forms a single planar layer that is 2.4 angstrom above the unreconstructed Ag surface. Moreover, our results reveal that multiple borophene phases exhibit these characteristics, denoting a unique form of polymorphism consistent with recent predictions. Furthermore, this observation of synthetic borophene as chemically discrete from the growth substrate suggests that it is possible to engineer a much wider variety of 2D materials than those accessible through bulk layered crystal structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2011

Synthesis-Structure-Performance Correlation for Polyaniline-Me-C Non-Precious Metal Cathode Catalysts for Oxygen Reduction in Fuel Cells

In this report, we present the systematic preparation of active and durable non-precious metal catalysts (NPMCs) for the oxygen reduction reaction in polymer electrolyte fuel cells (PEFCs) based on the heat treatment of polyaniline/metal/carbon precursors. Variation of the synthesis steps, heat-treatment temperature, metal loading, and the metal type in the synthesis leads to markedly different catalyst activity, speciation, and morphology. Microscopy studies demonstrate notable differences in the carbon structure as a function of these variables. Balancing the need to increase the catalyst's degree of graphitization through heat treatment versus the excessive loss of surface area that occurs at higher temperatures is a key to preparing an active catalyst. XPS and XAFS spectra are consistent with the presence of Me-N{sub x} structures in both the Co and Fe versions of the catalyst, which are often proposed to be active sites. The average speciation and coordination environment of nitrogen and metal, however, depends greatly on the choice of Co or Fe. Taken together, the data indicate that better control of the metal-catalyzed transformations of the polymer into new graphitized carbon forms in the heat-treatment step will allow for even further improvement of this class of catalysts.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2025

High spatial resolution neutron imaging of lithium-ion batteries: Correlating microstructure and lithium transport

Thick electrodes for lithium-ion batteries can increase the overall energy density, but increasing the electrode thickness introduces charge transport limitations. These limitations may be mitigated through proper electrode structuring. Here, high spatial resolution neutron imaging was used to understand the correlation between microstructure and lithium transport in lithium-ion anodes. Batteries with distinct graphite anode microstructures were produced and studied with high spatial resolution in operando neutron radiography to observe the effects of structure on transport. High spatial resolution neutron computed tomography was performed following in operando neutron radiography. X-ray computed tomography and scanning electron microscopy were used to observe the finer scale anode structure to complement neutron imaging. Solvent-free anodes containing a tightly-packed layered structure confined lithium movement close to the separator. This structure limited capacity, but supported better rate capability. Conversely, a more open pore structure in the wet cast anodes yielded higher capacity with reduced rate capability. Together, these results show that lithium distributions can be controlled by the macroscopic structure of the electrodes, the microstructural pore network, and the microscale active areas that support electrochemical reactions. Furthermore, multimodal imaging applying the complementary strengths of neutron and X-ray methods is shown as a tool for advancing battery design.

25 ENERGY STORAGE↗

DOE OSTI2016

Li Intercalation into Graphite: Direct Optical Imaging and Cahn–Hilliard Reaction Dynamics

Lithium intercalation into graphite is a critical process in energy storage technology. Studies of Li intercalation kinetics have proved challenging due to structural and phase complexity, and sample heterogeneity. Here we report direct time- and space-resolved, all-optical measurement of Li intercalation. We use a single crystal graphite electrode with lithographically defined disc geometry. All-optical, Raman and reflectance measurements distinguish the intrinsic intercalation process from side reactions, and provide new insight into the microscopic intercalation process. The recently proposed Cahn–Hilliard reaction (CHR) theory quantitatively captures the observed phase front spatial patterns and dynamics, using a two-layer free-energy model with novel, generalized Butler–Volmer kinetics. This approach unites Cahn–Hilliard and electrochemical kinetics, using a thermodynamically consistent description of the Li injection reaction at the crystal edge that involves a cooperative opening of graphene planes. Here, the excellent agreement between experiment and theory presented here, with single-crystal resolution, provides strong support for the CHR theory of solid-state reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗