Search NASA⌕ Search

SEARCH · Search NASA

Results for “load changes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence Q - Raw Data

Sequence Q: Dynamic Inflow (P) This sequence was designed to characterize the dynamic inflow variation using the five-hole probes that extend upwind of the leading edge of the blade. This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speeds ranged from 5 m/s to 15 m/s, and data were collected at a 0° yaw angle. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pretensioned to 40,000 N. The blade pitch angle was changed from the initial tip pitch angle to the final tip pitch angle at the maximum rate of 67°/s. This angle was maintained for the specified delay time duration. Then the blade was pitched back to the initial pitch angle and held for the specified hold time. This was repeated 20 times. The campaign at 15 m/s was aborted early due to excessive low-speed shaft torque loads. The file length varied depending on the time required to obtain 20 pitch cycles for the specified range of angles. The name convention was the standard format, except for the short campaigns collected to ascertain the functionality of the instrumentation. These points were collected at a 3° pitch angle and use the characters REF in the four digits that normally represent yaw angle.

17 WIND ENERGY↗

Deformation behavior of CP-titanium under strain path changes: Experiment and crystal plasticity modeling

The deformation behavior of commercially pure rolled titanium subjected to strain path changes is studied using experiments and a crystal plasticity model. Four different loading combinations are performed at room temperature to study the activation of slip, twinning, de-twinning and double-twinning in hexagonal closed packed titanium. The strain paths considered are: rolling direction compression (RDC) followed by normal direction compression (NDC), RDC followed by transverse direction compression (TDC), NDC followed by RDC, and NDC followed by TDC. An EBSD-based analysis of the distribution of boundary misorientation angles before and after reload was developed to analyze the evolution of {$10\bar{1}2$} tensile and {$11\bar{2}2$} compression twins. This analysis supports the model results concerning the treatment of twin reorientation. A de-twinning and double-twinning model accounting for back stress effects, an important feature of strain path changes, is implemented within the framework of the visco-plastic self-consistent (VPSC) model along with a dislocation density (DD) based hardening scheme. In the model, plasticity is accommodated by prismatic $\langle$a$\rangle$, basal $\langle$a$\rangle$ and pyramidal $\langle$c+a$\rangle$ slip modes, and {$10\bar{1}2$} tensile and {$11\bar{2}2$} compression twinning modes. The VPSC model predicts the evolution of twinning, de-twinning and double-twinning processes for both tensile and compression twinning modes under strain path change. The model predicts macroscopic stress-strain response, texture evolution, and twin volume fraction that are in agreement with experimental observations. The evolution of texture is investigated in detail by separately analyzing the twinned domains, rather than the evolution of the global texture.

36 MATERIALS SCIENCE↗

Validating Hydrogen Concentrations Ahead of Crack Tips

Current models for hydrogen embrittlement rely on adjustable parameters to correct for uncertainties in crack tip stress fields and subsequent H 2 -concentrations. Techniques are needed to quantify these concentrations ahead of crack tips in mechanically loaded materials, providing data for model calibration and validation. The goal of this work was to establish advanced analytical techniques to detect and quantitatively measure hydrogen ahead of cracks in stressed solids. Two advanced analytical techniques, kelvin probe force microscopy (KPFM) and nuclear reaction analysis (NRA), were explored to evaluate the feasibility to provide qualitative and quantitative H 2 -concentration fields in geometries designed to be 'loaded' while under observation. The feasibility of the KPFM technique at detecting hydrogen was evaluated using electrochemically precharged hydrogen as well as a mixed hydrogen gas atmosphere. The KPFM technique was able to detect the presence of elevated stress and hydrogen concentrations ahead of a tensile loaded crack tip. The results suggest that KPFM is a viable technique for qualitatively imaging changes in stress and hydrogen concentrations on the scale needed to inform predictive models. KPFM could be used to provide local stress and hydrogen variations associated with hydrogen traps or different phases which require sensitive measurements on the micron scale. NRA provided quantitative measurements of the hydrogen-isotope deuterium ahead of a tensile loaded notch, however, the vacancy formation due to the incident high energy He 3 beam overwhelmed stress-assisted enhancement of deuterium concentrations such that the effect of stress was overshadowed in this analysis. Modeling of the chemo- mechanical hydrogen concentration change was used to verify this observation.

08 HYDROGEN↗

Investigation of fracture in porous materials: a phase-field fracture study informed by ReaxFF

Microscopic features (e.g, pore shapes, sizes, and distribution) in porous material substantially affect the overall mechanical properties such as stiffness and strength. In turn, these material properties determine the macroscopic behaviors of fracture in the porous material. In certain cases, macroscopic properties can be derived from the porous skeleton and void ratio (i.e., porosity), but in many other cases, such derivation is a challenging task. This paper presents a numerical investigation of microporosity and micropore shapes effect on the macrofracture behavior in porous amorphous silica. For this study, we extend the recently-proposed combined molecular dynamic (MD) and phase-field (PF) fracture modeling approach by including different pore shapes in the atomistic domain. In the MD simulations, we adopt ReaxFF to evaluate the material properties, where four different micropore cases are considered. Based on the material properties derived from MD simulations, the macrofracture propagation of porous media is studied using hybrid PF simulation. In the characterization of the pore structure, the concept of pore ligament is proposed to relate the pore shape and the critical energy release rate. Two classical fracture problems were used to evaluate the effect of pore shape on the macrofracture behavior. The results of the case study show that although the micropore shapes change the macrofracture behaviors, these effects vary with the geometry and loading conditions of macroscopic boundary value problems. Furthermore, the case study also shows that the influence of micropore structure can be captured at the macroscopic level through the material properties derived from the MD simulations.

42 ENGINEERING↗

Bayesian calibration and uncertainty quantification of a rate-dependent cohesive zone model for polymer interfaces

In this work we present a rate-dependent cohesive zone model for the fracture of polymeric interfaces and performs a Bayesian calibration, an uncertainty quantification, and a sensitivity analysis for the model. The proposed cohesive zone model accounts for both reversible elastic and irreversible rate-dependent separation sliding deformation at the interface. The viscous dissipation due to the irreversible opening at the interface is modeled using elastic-viscoplastic kinematics that incorporates the effects of strain rate. Inverse calibration of parameters for such complex models through trial and error is challenging due to the large number of parameters of the model. Moreover, the calibrated parameter values are often non-unique and uncertain when the available experimental data is limited. To tackle this challenge, we employ a Bayesian calibration approach to identify parameters from experimental data, the resulting parameters significantly enhance the accuracy of the model. To quantify the uncertainty associated with the inverse parameter estimation, a modular Bayesian approach is employed to calibrate the unknown model parameters, accounting for the parameter uncertainty of the cohesive zone model. The advantages of the Bayesian calibration over a deterministic parameter fit are demonstrated. Further, to quantify the model uncertainties, such as incorrect assumptions or missing physics, a discrepancy function is introduced, which significantly improves the model’s prediction. Finally, the total uncertainty of the model is quantified in a predictive setting. A sensitivity analysis is performed to assess how changes in the input variables of the model affect the peak load, facilitating the identification of a concise set of highly influential parameters. The present approach can be used for calibration and uncertainty quantification for other complex computational mechanics models. It should also facilitate the designing of interface materials under uncertainty.

42 ENGINEERING↗

Measurements of ultrafine particles from a gas-turbine burning biofuels

Measurements of ultrafine particles have been performed at the exhaust of a low emission microturbine for power generation. This device has been fuelled with liquid fuels, including a commercial diesel oil, a mixture of the diesel oil with a biodiesel and kerosene, and tested under different loads. Primarily attention has been focused on the measurements of the size distribution functions of the particles emitted from the system by using particle differential mobility analysis. A bimodal size distribution function of the particle emitted has been found in all the examined conditions. Burning diesel oil, the first mode of the size distribution function of the combustion-formed particles is centered at around 2-3 nm, whereas the second mode is centered at about 20-30 nm. The increase of the turbine load and the addition of 50% of biodiesel has not caused changes in the shape of size distribution of the particles. A slightly decrease of the amount of particle formed has been found. By using kerosene the amount of emitted particles increases of more than one order of magnitude. Also the shape of the size distribution function changes with the first mode shifted towards larger particles of the order of 8-10 nm but with a lower emission of larger 20-30 nm particles. Overall, in this conditions, the mass concentration of particles is increased respect to the diesel oil operation. Particle sizes measured with the diesel oil have been compared with the results on a diesel engine operated in the same power conditions and with the same fuel. Measurements have showed that the mean sizes of the formed particles do not change in the two combustion systems. However, diesel engine emits a number concentration of particles more than two orders of magnitude higher in the same conditions of power and with the same fuel. By running the engine in more premixed-like conditions, the size distribution function of the particles approaches that measured by burning kerosene in the microturbine indicating that the distribution function of the sizes of the emitted particles can be strongly affected by combustion conditions. (author)

02 PETROLEUM↗

Reversal of asymmetry of x-ray peak profiles from individual grains during a strain path change.

X-ray peak profiles are measured from individual bulk grains during tensile deformation. Two differently oriented copper samples pre-deformed in tension show the expected peak profile asymmetry caused by intra-grain stresses. One of the samples is oriented to achieve a significant change of the intra-grain stresses during in situ tensile loading and this is observed as a reversal of the sign of the peak profile asymmetry.

36 MATERIALS SCIENCE↗

Planning for the future

Four changes to integrated resource planning could significantly improve alignment between future utility spending and the forces and changes that are upending past preconceptions of how to predict future load. (author)

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Summary Report of the INL-JISEA Workshop on Nuclear Hybrid Energy Systems

Hybrid energy systems utilize two or more energy resources as inputs to two or more physically coupled subsystems to produce one or more energy commodities as outputs. Nuclear hybrid energy systems can be used to provide load-following electrical power to match diurnal to seasonal-scale changes in power demand or to compensate for the variability of renewable wind or solar generation. To maintain economical, full rate operation of the nuclear reactor, its thermal energy available when power demand is low could be diverted into making synthetic vehicle fuels of various types. The Institute for Nuclear Energy Science and Technology (INEST) and the Joint Institute for Strategic Energy Analysis (JISEA) co-sponsored an international workshop to identify research topics important in advancing the potential use of hybrid systems with a specific focus on nuclear-renewable hybrid systems. The workshop included presentations ranging from energy challenges and research and development (R&D) directions being pursued by nations to multiple options for hybrid systems. Those options include one that is being commercialized to other opportunities and analysis results quantifying them. The workshop also involved two breakout sessions - one focused on thermal energy management issues especially at unit-operation scale and the second focused on system operations issues including system controls, regulatory issues, technical and economic analysis, and market challenges. A discussion involving the full group focused on more general issues such as societal involvement and participation. Key criteria for selecting hybrid energy system projects and metrics for comparing them were also identified by the full group. The workshop's findings are being used initially by INEST to define topics for a research preproposal solicitation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

CIRFT Testing of Used Nuclear Fuel Rods from the Limerick Generating Station Boiling Water Reactor (FY15 Status Report)

The objective of this project is to perform a systematic study of spent nuclear fuel (SNF, also known as “used nuclear fuel” [UNF]) integrity under simulated transportation environments using the Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) hot-cell testing technology developed at Oak Ridge National Laboratory (ORNL) in August 2013. Under Nuclear Regulatory Commission (NRC) sponsorship, ORNL completed four benchmark tests, four static tests, and twelve dynamic or cycle tests on H. B. Robinson (HBR) high burn-up (HBU) fuel. The clad of the HBR fuels was made of Zircaloy-4. Testing was continued in fiscal year (FY) 2014 using Department of Energy (DOE) funds. Additional CIRFT testing was conducted on three HBR rods; two specimens failed, and one specimen was tested to over 2.23 × 10 7 cycles without failing. The data analysis on all the HBR SNF rods demonstrated that it is necessary to characterize the fatigue life of the SNF rods in terms of (1) the curvature amplitude and (2) the maximum absolute of curvature extremes. The maximum extremes are significant because they signify the maximum tensile stress for the outer fiber of the bending rod. CIRFT testing has also addressed a large variation in hydrogen content on the HBR rods. While the load amplitude is the dominant factor that controls the fatigue life of bending rods, the hydrogen content also has an important effect on the lifetime attained at each load range tested. In FY 15, eleven SNF rod segments from the Limerick BWR were tested using the ORNL CIRFT equipment; one test under static conditions and ten tests under dynamic loading conditions. Under static unidirectional loading, a moment of 85 N·m was obtained at a maximum curvature of 4.0 m -1 . The specimen did not show any sign of failure during three repeated loading cycles to a similar maximum curvature. Ten cyclic tests were conducted with amplitudes varying from 15.2 to 7.1 N·m. Failure was observed in nine of the tested rod specimens. The cycles-to-failure ranged from 1.22 × 10 5 to 4.70 × 10 6 , and the amplitudes varied from 15.2 to 7.6 N·m. The measurements at the interrupts indicated a range of flexural rigidity from 30 to 50 N·m 2 . Online monitoring revealed that the flexural rigidity was slightly lower due to the higher loading, from 25 to 42 N·m 2 . Generally, no substantial change of rigidity was observed based on the online monitoring during the cyclic fatigue testing process. Overall, the decreasing trend of sample lifetime with increasing amplitude is well defined.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BWR Spent Nuclear Fuel Interfacial Bonding Efficiency Study

The objective of this project is to perform a systematic study of spent nuclear fuel (SNF, also known as “used nuclear fuel” [UNF]) integrity under simulated transportation environments using the Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) hot-cell testing technology developed at Oak Ridge National Laboratory (ORNL) in August 2013. Under Nuclear Regulatory Commission (NRC) sponsorship, ORNL completed four benchmark tests, four static tests, and twelve dynamic or cycle tests on H. B. Robinson (HBR) high burn-up (HBU) fuel. The clad of the HBR fuels was made of Zircaloy-4. Testing was continued in fiscal year (FY) 2014 using Department of Energy (DOE) funds. Additional CIRFT testing was conducted on three HBR rods; two specimens failed, and one specimen was tested to over 2.23 × 10 7 cycles without failing. The data analysis on all the HBR SNF rods demonstrated that it is necessary to characterize the fatigue life of the SNF rods in terms of (1) the curvature amplitude and (2) the maximum absolute of curvature extremes. The maximum extremes are significant because they signify the maximum tensile stress for the outer fiber of the bending rod. CIRFT testing has also addressed a large variation in hydrogen content on the HBR rods. While the load amplitude is the dominant factor that controls the fatigue life of bending rods, the hydrogen content also has an important effect on the lifetime attained at each load range tested. In FY 15, eleven SNF rod segments from the Limerick BWR were tested using the ORNL CIRFT equipment; one test under static conditions and ten tests under dynamic loading conditions. Under static unidirectional loading, a moment of 85 N·m was obtained at a maximum curvature of 4.0 m -1 . The specimen did not show any sign of failure during three repeated loading cycles to a similar maximum curvature. Ten cyclic tests were conducted with amplitudes varying from 15.2 to 7.1 N·m. Failure was observed in nine of the tested rod specimens. The cycles-to-failure ranged from 1.22 × 10 5 to 4.70 × 10 6 , and the amplitudes varied from 15.2 to 7.6 N·m. The measurements at the interrupts indicated a range of flexural rigidity from 30 to 50 N·m 2 . Online monitoring revealed that the flexural rigidity was slightly lower due to the higher loading, from 25 to 42 N·m 2 . Generally, no substantial change of rigidity was observed based on the online monitoring during the cyclic fatigue testing process. Overall, the decreasing trend of sample lifetime with increasing amplitude is well defined.

interface bonding efficiency↗

Root Influences on Mobilization and Export of Mineral-bound Soil Organic Matter

Biogeochemical cycles within mountainous watersheds are key regulators of ecosystem carbon storage and downstream nutrient loadings, and they have shown to be particularly vulnerable to climate change impacts. Increasing temperature and persistent droughts have already dramatically changed vegetation cover across the mountainous western US, with unknown consequences for soil carbon and nutrient cycles belowground. What remains elusive is to what extent associated changes in root-soil interactions may mobilize the vast pool of organic matter (OM) that has been stabilized by associations with minerals for centuries or millennia. Although plant root-driven OM mobilization from minerals may be a central control on carbon loss and nutrient export, such mechanisms are currently missing from conceptual and numerical models. The overall objective of this Exploratory Project is to identify the biogeochemical mechanisms by which roots destabilize mineral-associated organic matter (MAOM) and the cumulative impact on carbon and nutrient fate. To accomplish this goal, we integrated well-controlled laboratory experiments with in-field measurements and a scalable modeling approach. First, we conducted model system experiments to assess the vulnerability of MAOM to exudate-mediated mechanisms. Our results show that common root exudates effectively destabilize MAOM not only through direct, ligand-driven mobilization mechanisms, but also indirect, microbially-mediated mechanisms relying on secondary metabolites and enzymes. We further found that OM bound to poorly crystalline Fe and Al (hydr)oxides is more vulnerable to exudate-induced destabilization than OM bound to more crystalline phases, particularly in response to direct, ligand-promoted mechanisms. These findings demonstrate that the stability of MAOM is not just a function of their inherent properties, but also will depend in large parts on the ability of plant roots and microbes to produce exudates capable of triggering suitable mobilization mechanisms. We further employed a well-controlled rhizobox approach, combining advanced microsensor and mass spectrometry techniques, to resolve spatiotemporal variations in the composition and availability of exudates along single growing roots of grasses. Our results show that the composition of functionally relevant exudate compounds varies at extremely short time scales, seemingly shifting from ligands such as aromatic acids around root tips to less reactive metabolites such as amino acids around mature root segments. These results suggest a prevalence of direct MAOM mobilization mechanisms around the root tip, while indirect MAOM mobilization strategies may dominate around more mature root segments. Additionally, we utilized microsensor measurements in rhizoboxes to parameterize a rhizosphere (hydro)biogeochemistry reactive transport model (eSTOMP-ROOTS). The resulting model was used to assess how root exudations affects the stability of MAOM. Model simulations show that diel pulses of root exudation are strong enough to cause oscillations in biogeochemical conditions—particularly in pH, oxygen concentrations, and microbial activity— that repeatedly disrupt MAOM. Finally, we assessed field-scale impacts of root-driven MAOM destabilization over short and long time scales. A combination of in-field incubations and field-based characterizations showed that MAOM may not only be vulnerable to seasonal variations in root activity, but also to root-driven weathering over pedogenic time scales. In sum, results from our Exploratory Award highlight the strong control plant roots exert on MAOM mobilization and, thus, on the potential for carbon and nutrient export from watersheds.

54 ENVIRONMENTAL SCIENCES↗

Structural Characterization of Deployed Thermoplastic and Thermoset Composite Tidal Turbine Blades

The National Renewable Energy Laboratory worked with Verdant Power to manufacture, and characterize, novel thermoplastic composite blades on their Gen5d 5 m diameter turbines at the Roosevelt Island Tidal Energy (RITE) site in the East River in N.Y. to demonstrate a low-cost manufacturing process for marine energy structures. Verdant had designed, manufactured, and deployed epoxy thermoset composite blades on three Gen5d turbines in October 2020. At a maintenance cycle in May 2021, a Gen5d turbine equipped with the NREL thermoplastic blades was deployed and retrieved in October 2021. Modal, static and fatigue structural characterization was performed on both blade types before and after the deployment. The static and modal test results showed that the thermoplastic blades were slightly stiffer than the epoxy blades both dry and after the deployment. The epoxy blades had about 8% increase in strain at the applied load after the deployment, whereas the thermoplastic blade strains were not changed significantly. Ultimately the thermoplastic blade failed during fatigue testing due to a crack which is thought to have initiated between the internal foam and the laminate at the location of the internal instrumentation. The Verdant Power Gen5d epoxy blades did not have this internal instrumentation and did not have this failure, performing adequately through the operational period. A lack of design information and fatigue data for both the thermoplastic laminates and the adhesive used means that further work is needed to fully understand his failure and the root cause analysis is ongoing. This paper provides details on the thermoplastic blade manufacturing, materials, test methodology and results.

17 WIND ENERGY↗

Adoption of AI in the Utility T&D Sector: Use Cases, Consequence, Assessment and Benefits

Digital transformation and utilization of artificial intelligence (AI) in the electric grid are fundamentally changing the industry’s approach to common problems and enabling a broader paradigm shift in grid planning and operations. The change in approach is circularly both enabling and driving modernization, with load growth and reliable management of data center and AI infrastructure shifting away from planning approaches with relatively predictable behaviors and toward a mix of consumer and industrial choices that surpass human cognitive abilities to process. This movement has potential to condition humans to not understand the system on which the AI depends, while requiring it for development of the necessary infrastructure. Approaches which would address most likely grid conditions and events, such as faults, aging of equipment, and weather, now must also account for large loads which shift not based upon weather or time of day, but the computational load. Quantifying computational load is independent of the traditional grid forecasting variables, where a data center’s aggregate load is determined by user and AI system behavior and decoupled from normal grid planning and operations. AI is both the cause and solution for these challenges, with new grid planning tools integrating massive amounts of decisions into frameworks.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Development of a Dynamic Model and Control System for Load-Following Studies of Supercritical Pulverized Coal Power Plants

Traditional energy production plants are increasingly forced to cycle their load and operate under low-load conditions in response to growth in intermittent renewable generation. A plant-wide dynamic model of a supercritical pulverized coal (SCPC) power plant has been developed in the Aspen Plus Dynamics® (APD) software environment and the impact of advanced control strategies on the transient responses of the key variables to load-following operation and disturbances can be studied. Models of various key unit operations, such as the steam turbine, are developed in Aspen Custom Modeler® (ACM) and integrated in the APD environment. A coordinated control system (CCS) is developed above the regulatory control layer. Three control configurations are evaluated for the control of the main steam; the reheat steam temperature is also controlled. For studying servo control performance of the CCS, the load is decreased from 100% to 40% at a ramp rate of 3% load per min. The impact of a disturbance due to a change in the coal feed composition is also studied. The CCS is found to yield satisfactory performance for both servo control and disturbance rejection.

20 FOSSIL-FUELED POWER PLANTS↗

Sensitivity Analysis of Numerical Modeling Input Parameters on Wind Turbine Loads in Deterministic Transient Load Cases

Aero-hydro-elastic-servo numerical models used to design and analyze wind turbines are based on thousands of variable input parameters that dictate the inflow, aerodynamic, structural, and control characteristics of the system as well as sea state, hydrodynamic, and mooring characteristics for fixed-bottom and floating offshore wind turbines. Each of these parameters has some level of uncertainty, which can significantly impact the predicted loads. Understanding the uncertainty in the inputs is critical to understanding the uncertainty in the outputs. This work demonstrates a screening technique to identify which parameters ultimate loads are most sensitive to so that more focus can be given to quantifying the possible range of those parameters. This technique has been demonstrated previously for different turbine and load case types and is extended here for a floating offshore wind turbine in design load cases with transient events both in the inflow and operations. Each load case features a deterministic gust, including variations in wind speed, direction, and shear. Load cases are considered with an operating turbine as well as with prescribed fault, startup, and shutdown procedures. The study found that key input parameters with a large impact on loads include the length of the gust, the magnitude of direction change and speed in the gust, the initial wind speed, and the shape of the gust profile.

17 WIND ENERGY↗

Ion Exchange Temperature Testing with SRF Resin

Ion exchange using the Spherical Resorcinol-Formaldehyde (SRF) resin has been selected by the U.S. Department of Energy’s Office of River Protection for use in the Pretreatment Facility of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) and for potential application in an at-tank deployment for removing 137Cs. Recent proposed changes to the WTP ion exchange process baseline indicate that higher temperatures (50°C) to alleviate post-filtration precipitation issues prior to reaching the ion exchange columns may be required. Therefore, it is important to understand the behavior of SRF resin performance under the conditions expected with the new equipment and process changes. This research examined the impact of elevated temperature on resin loading and resin degradation during extended solution flow using elevated temperature (45°, 50°, 55°, 60°, 65°, 75°C). Testing for extended times at elevated temperatures showed that the resin does degrade and loading capacity is reduced at and above 45°C. Above 60°C the resin appears to not load at all.

Hanford Tank Waste Treatment and Immobilization Pl↗

Multi-cycle boiling water reactor fuel cycle optimization

In this work a new computer code, BWROPT (Boiling Water Reactor Optimization), is presented. BWROPT uses the Parallel Simulated Annealing (PSA) algorithm to solve the out-of-core optimization problem coupled with an in-core optimization that determines the optimum fuel loading pattern. However it uses a Haling power profile for the depletion instead of optimizing the operating strategy. The result of this optimization is the optimum new fuel inventory and the core loading pattern for the first cycle considered in the optimization. Several changes were made to the optimization algorithm with respect to other nuclear fuel cycle optimization codes that use PSA. Instead of using constant sampling probabilities for the solution perturbation types throughout the optimization as is usually done in PSA optimizations the sampling probabilities are varied to get a better solution and/or decrease runtime. The new fuel types available for use can be sorted into an array based on any number of parameters so that each parameter can be incremented or decremented, which allows for more precise fuel type selection compared to random sampling. Also, the results are sorted by the new fuel inventory of the first cycle for ease of comparing alternative solutions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗