Search NASA⌕ Search

SEARCH · Search NASA

Results for “module efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Metal modulation epitaxy growth for extremely high hole concentrations above 10{sup 19} cm{sup -3} in GaN

The free hole carriers in GaN have been limited to concentrations in the low 10{sup 18} cm{sup -3} range due to the deep activation energy, lower solubility, and compensation from defects, therefore, limiting doping efficiency to about 1%. Herein, we report an enhanced doping efficiency up to {approx}10% in GaN by a periodic doping, metal modulation epitaxy growth technique. The hole concentrations grown by periodically modulating Ga atoms and Mg dopants were over {approx}1.5x10{sup 19} cm{sup -3}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of Atmospheric Variations on Photovoltaic Performance and Modeling Their Effects for Days with Clear Skies: Preprint

Although variation in photovoltaic (PV) performance is predominantly influenced by clouds, performance variations also exist for days with clear skies with different amounts of atmospheric constituents that absorb and reflect different amounts of radiation as it passes through the earth's atmosphere. The extent of the attenuation is determined by the mass of air and the amounts of water vapor,aerosols, and ozone that constitute the atmosphere for a particular day and location. Because these constituents selectively absorb radiation of particular wavelengths, their impact on PV performance is sensitive to the spectral response of the PV device. The impact may be assessed by calculating the spectral mismatch correction. This approach was validated using PV module performance data atthe National Renewable Energy Laboratory (NREL) for summer, fall, and winter days with clear skies. The standard deviation of daily efficiencies for single-crystal Si, a-Si/a-Si/a-Si:Ge, CdTe, and CIGS PV modules were reduced to 0.4% to 1.0% (relative) by correcting for spectral mismatch, temperature, and angle-of-incidence effects.

14 SOLAR ENERGY↗

Electrooptic despeckler based on helix-free ferroelectric liquid crystal

In an experimental sample of a despeckler, consisting of an electrooptic cell with a 20-μm-thick helix-free liquid ferroelectric, to which an electric field with a strength of ∼3V μm{sup −1} and a frequency of 2 kHz is applied, we obtained spatially nonuniform phase modulation of a laser beam with a value exceeding π. The effect allows the implementation of speckle noise suppression with an efficiency of 10.7 dB. (laser applications and other topics in quantum electronics)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Spectrum sensitivity, energy yield, and revenue prediction of PV and CPV modules

Impact on module performance of spectral irradiance variation has been determined for III-V multijunctions compared against the four most common flat-plate module types (cadmium telluride, multicrystalline silicon, copper indium gallium selenide, and monocrystalline silicon. Hour-by-hour representative spectra were generated using atmospheric variables for Albuquerque, New Mexico, USA. Convolution with published values for external quantum efficiency gave the predicted current output. When combined with specifications of commercial PV modules, energy yield and revenue were predicted. This approach provides a means for optimizing PV module design based on various site-specific temporal variables.

14 SOLAR ENERGY↗

Floating Silicon Method

The Floating Silicon Method (FSM) project at Applied Materials (formerly Varian Semiconductor Equipment Associates), has been funded, in part, by the DOE under a “Photovoltaic Supply Chain and Cross Cutting Technologies” grant (number DE-EE0000595) for the past four years. The original intent of the project was to develop the FSM process from concept to a commercially viable tool. This new manufacturing equipment would support the photovoltaic industry in following ways: eliminate kerf losses and the consumable costs associated with wafer sawing, allow optimal photovoltaic efficiency by producing high-quality silicon sheets, reduce the cost of assembling photovoltaic modules by creating large-area silicon cells which are free of micro-cracks, and would be a drop-in replacement in existing high efficiency cell production process thereby allowing rapid fan-out into the industry.

14 SOLAR ENERGY↗

Doping-modulated strain control of bifunctional electrocatalysis for rechargeable zinc–air batteries

Changes in the local atomic arrangement in a crystal caused by lattice-mismatch-induced strain can efficiently regulate the performance of electrocatalysts for zinc–air batteries (ZABs) in many manners, mainly due to modulated electronic structure configurations that affect the adsorption energies for oxygen-intermediates formed during oxygen reduction and evolution reactions (ORR and OER). However, the application of strain engineering in electrocatalysis has been limited by the strain relaxation caused by structural instability such as dissolution and destruction, leading to insufficient durability towards the ORR/OER. In this work, we propose a doping strategy to modulate the phase transition and formation of self-supported cobalt fluoride–sulfide (CoFS) nanoporous films using a low amount of copper (Cu) as a dopant. This well-defined Cu–CoFS heterostructure overcomes the obstacle of structural instability. Our study of the proposed Cu–CoFS also helps establish the structure–property relationship of strained electrocatalysts by unraveling the role of local strain in regulating the electronic structure of the catalyst. As a proof-of-concept, the Cu–CoFS electrocatalyst with doping-modulated strain exhibited superior onset potentials of 0.91 V and 1.49 V for the ORR and OER, respectively, surpassing commercial Pt/C@RuO 2 and benchmarking non-platinum group metal (non-PGM) catalysts. ZABs with the Cu–CoFS catalyst delivered excellent charge/discharge cycling performance with an extremely low voltage gap of 0.5 V at a current density of 10 mA cm –2 and successively 0.93 V at a high current density of 100 mA cm –2 and afforded an outstanding peak power density of 255 mW cm –2 .

25 ENERGY STORAGE↗

Outage Forecast-Based Preventative Scheduling Model for Distribution System Resilience Enhancement

Distribution system resilience enhancement is an important topic to ensure customers have access to power supply during extreme events. In fact, certain weather-related extreme events can be predicted ahead of time. Therefore, it is important to investigate how to predict grid outages using extreme weather forecasts, and how outage predictions can be incorporated into distribution system resilience enhancement. In this paper, a preventative scheduling model for distribution systems is proposed. The model targets at allocating resources, especially mobile responsive resources such as mobile backup generators and mobile energy storage systems, to prepare for an extreme event in the day-ahead context. To achieve efficient resource allocation and scheduling, a machine learning-based outage prediction module is developed to predict vulnerable or risky segments of the distribution system based on historical operating records and extreme weather event forecast. By integrating the outage prediction results into the scheduling model, optimal resource allocation can be derived to help distribution systems prepare for an upcoming event and improve resilience performance. A real distribution feeder in North Carolina, U.S. is used in the case study to validate the proposed approach.

distributed energy resources↗

How [NOT] to Measure a Solar Cell to Get the Highest Efficiency

The multibillion-dollar photovoltaic (PV) industry sells products by the watt; the calibration labs measure this parameter at the cell and module level with the lowest possible uncertainty of 1-2 percent. The methods and procedures to achieve a measured 50 percent efficiency on a thin-film solar cell are discussed. This talk will describe methods that ignore procedures that increase the uncertainty. Your questions will be answered concerning 'Everything you Always Wanted to Know about Efficiency Enhancements But Were Afraid to Ask.' The talk will cover a step-by-step procedure using examples found in literature or encountered in customer samples by the National Renewable Energy Laboratory's (NREL's) PV Performance Characterization Group on how to artificially enhance the efficiency. The procedures will describe methods that have been used to enhance the current voltage and fill factor.

14 SOLAR ENERGY↗

P‐Doping Modulated RuIr Nanoparticles Anchored on Co/N/C Catalysts with Improved Alkaline Hydrogen Evolution Activity and Stability

Achieving efficient and stable hydrogen evolution reactions in alkaline conditions is crucial for hydrogen production. In this study, a RuIr/Co (SA) NC-P catalyst featuring RuIr alloys alongside P-doping and CoNx sites is developed. RuIr alloying optimizes the electronic structure between Ru and Ir, promoting electron transfer from Ru to Ir. P-doping further modulates the electronic properties of RuIr alloys, optimizing hydrogen binding energy and weakening Ru─OH binding energy, facilitating rapid H 2 generation and OH ad transfer. Meanwhile, CoNx promotes water dissociation, providing a fast proton delivery path for RuIr alloys. The catalyst exhibits enhanced HER activity with a low overpotential of 20 mV at 10 mA cm −2 , a Tafel slope of 20.4 mV dec −1 , and a turnover frequency of 19.5 H 2 s −1 at 150 mV overpotential. Moreover, catalyst stability is improved 8 times by mitigating RuIr alloy dissolution/agglomeration via P-doping. In conclusion, this work introduces a promising approach for developing efficient and stable HER electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Method for Projecting Cloud Shadows Onto a Central Receiver Field to Predict Receiver Damage

This work demonstrates methods of mapping high-spatial-resolution direct normal irradiance (DNI) data from satellites, Total Sky Imagers (TSIs), and analogous data sources onto a heliostat field for characterizing the spatial and temporal variation of the incident flux on a central receiver tower during cloud transient events. The mapping methods are incorporated into an optical software module that interfaces with CoPylot–SolarPILOT’s python API– to provide computationally efficient optical simulation of the heliostat field and the solar power tower. Eventually, this optical model will be incorporated into optimization models whereby a plant operator can understand the effects of cloud transient events on overall power production and receiver lifetime due to creep-fatigue damage and therefore make better informed decisions about receiver shutdown events. By more accurately modelling the effects of cloud events on receiver flux maps, this work may determine the magnitude and frequency of thermal cycling on receiver tubes and panels using actual or realistic cloud shapes instead of averaged DNI values–which may undercount the total cycle number. This work may also prevent unnecessary plant shutdowns due to overly precautionary control strategies and characterize the relative impact of various cloud types on receiver life. We plan to eventually integrate this methodology into the System Advisor Model (SAM) to improve performance model accuracy during periods of cloudiness. In this paper, we demonstrate generating DNI maps and mapping them to a solar field in CoPylot using 10 m resolution data from publicly available Sentinel-2 satellite data over the Crescent Dunes plant.

Mullin, Matthew↗

Multiscale Characterization of Photovoltaic Modules—Case Studies of Contact and Interconnect Degradation

The current popularity of photovoltaic (PV) systems is due in large part to their exceptional reliability and significantly lower cost than other energy sources. Studying cell and module degradation is key to promote further development in the state of the art. Fielded or accelerated aged modules exhibit different failure modes, of which metallization degradation (contacts and interconnections) is prevalent. In this work, we discuss how multiscale characterization methods can be applied to a variety of module technologies that have been field exposed and have undergone accelerated age testing. These methods include performing characterization on the module level, cell level, and finally the materials level. The observed performance losses from the module- and cell-level characterization can be correlated with materials properties to find out the root cause of degradation. We recommend an initial nondestructive characterization suite, including module- and cell-level current-voltage ( I--V ), Suns-V OC , photoluminescence and electroluminescence imaging, quantum efficiency, ultraviolet fluorescence imaging, and thermal infrared imaging. Samples are then extracted from particularly degraded regions of the module and prepared for materials characterization techniques, such as top-down and cross-sectional scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, Raman spectroscopy, and transmission electron microscopy, allowing a deeper look into the mechanism behind the metallization degradation. This article serves as an instructional review to introduce the different multiscale characterization methods and how they can be effectively applied to perform PV degradation studies. Furthermore, we also share some of our examples and discuss the strengths, limitations, and best practices for each of the characterization techniques.

14 SOLAR ENERGY↗

Phase 1 Development Report for the SESSA Toolkit.

The Site Exploitation System for Situational Awareness ( SESSA ) tool kit , developed by Sandia National Laboratories (SNL) , is a comprehensive de cision support system for crime scene data acquisition and Sensitive Site Exploitation (SSE). SESSA is an outgrowth of another SNL developed decision support system , the Building R estoration Operations Optimization Model (BROOM), a hardware/software solution for data acquisition, data management, and data analysis. SESSA was designed to meet forensic crime scene needs as defined by the DoD's Military Criminal Investigation Organiza tion (MCIO) . SESSA is a very comprehensive toolki t with a considerable amount of database information managed through a Microsoft SQL (Structured Query Language) database engine, a Geographical Information System (GIS) engine that provides comprehensive m apping capabilities, as well as a an intuitive Graphical User Interface (GUI) . An electronic sketch pad module is included. The system also has the ability to efficiently generate necessary forms for forensic crime scene investigations (e.g., evidence submittal, laboratory requests, and scene notes). SESSA allows the user to capture photos on site, and can read and generate ba rcode labels that limit transcription errors. SESSA runs on PC computers running Windows 7, but is optimized for touch - screen tablet computers running Windows for ease of use at crime scenes and on SSE deployments. A prototype system for 3 - dimensional (3 D) mapping and measur e ments was also developed to complement the SESSA software. The mapping system employs a visual/ depth sensor that captures data to create 3D visualizations of an interior space and to make distance measurements with centimeter - level a ccuracy. Output of this 3D Model Builder module provides a virtual 3D %22walk - through%22 of a crime scene. The 3D mapping system is much less expensive and easier to use than competitive systems. This document covers the basic installation and operation of th e SESSA tool kit in order to give the user enough information to start using the tool kit . SESSA is currently a prototype system and this documentation covers the initial release of the tool kit . Funding for SESSA was provided by the Department of Defense (D oD), Assistant Secretary of Defense for Research and Engineering (ASD(R&E)) Rapid Fielding (RF) organization. The project was managed by the Defense Forensic Science Center (DFSC) , formerly known as the U.S. Army Criminal Investigation Laboratory (USACIL) . ACKNOWLEDGEMENTS The authors wish to acknowledge the funding support for the development of the Site Exploitation System for Situational Awareness (SESSA) toolkit from the Department of Defense (DoD), Assistant Secretary of Defense for Research and Engineering (ASD(R&E)) Rapid Fielding (RF) organization. The project was managed by the Defense Forensic Science Center (DFSC) , formerly known as the U.S. Army Criminal Investigation Laboratory (USACIL). Special thanks to Mr. Garold Warner, of DFSC, who served as the Project Manager. Individuals that worked on the design, functional attributes, algorithm development, system arc hitecture, and software programming include: Robert Knowlton, Brad Melton, Robert Anderson, and Wendy Amai.

Knowlton, Robert G.↗

LH power modulation experiment on JET

LH power modulation was recently used at JET to quantify experimentally the LH current drive efficiency and power deposition. A new approach was applied for the analysis of the amplitude and phase of electron temperature T{sub e} perturbations {delta}T{sub e}(k{omega}{sub o}) at different harmonics k of the modulation frequency {omega}{sub o}. A solution of the Fokker-Planck equation combined with heat transport modelling was used to study the dependence of the ratio of the perturbation of different harmonics k and n, {delta}T{sub e}(k{omega}{sub o})/{delta}T{sub e}(n{omega}{sub o}), and the phase shift of the harmonics {delta}{phi}(k{omega}{sub o}) on the plasma parameters and electron distribution function plateau width, which is directly connected to the current drive efficiency. The results of the modelling were compared with the experimental data to estimate the current drive efficiency. In addition, LH power deposition profiles were deduced from the radial dependence of {delta}{phi}({omega}{sub o}). The maximum of the LH power deposition becomes more peripheral and with a reduced current drive efficiency at higher densities. In H-Mode plasmas, at pedestal densities above the LH accessibility limit, a large fraction of the power is absorbed beyond the separatrix. Finally, the experimental power deposition profiles are more peripheral than the calculated ones obtained from combined ray tracing and Fokker-Planck Plank modelling. The experimental results indicate that the LH power spectrum in the plasma is modified, with more power in the high N// components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hydrophobic Moiety of Cationic Lipids Strongly Modulates Their Transfection Activity

Synthetic cationic lipids are widely used components of nonviral gene carriers, and the factors regulating their transfection efficiency are the subject of considerable interest. In view of the important role that electrostatic interactions with the polyanionic nucleic acids play in formation of lipoplexes, a common empirical approach to improving transfection has been the synthesis and testing of amphiphiles with new versions of positively charged polar groups, while much less attention has been given to the role of the hydrophobic lipid moieties. On the basis of data for {approx}20 cationic phosphatidylcholine (PC) derivatives, here we demonstrate that hydrocarbon chain variations of these lipids modulate by over 2 orders of magnitude their transfection efficiency. The observed molecular structure-activity relationship manifests in well-expressed dependences of activity on two important molecular characteristics, chain unsaturation and total number of carbon atoms in the lipid chains, which is representative of the lipid hydrophobic volume and hydrophilic-lipophilic ratio. Transfection increases with decrease of chain length and increase of chain unsaturation. Maximum transfection was found for cationic PCs with monounsaturated 14:1 chains. It is of particular importance that the high-transfection lipids strongly promote cubic phase formation in zwitterionic membrane phosphatidylethanolamine (PE). These remarkable correlations point to an alternative, chain-dependent process in transfection, not related to the electrostatic cationic-anionic lipid interactions.

59 BASIC BIOLOGICAL SCIENCES↗

Boosting CO 2 reduction on Fe-N-C with sulfur incorporation: Synergistic electronic and structural engineering

Developing earth-abundant efficient catalysts for CO 2 reduction reaction (CO 2 RR) is of paramount importance for electrochemical conversion of CO 2 into value-added products. Despite numerous studies on iron and nitrogen codoped carbon (Fe-N-C) catalysts, grand challenges exist due to limited performance and understanding of catalytic mechanisms. This study reports a general strategy to boost electrocatalytic CO 2 RR activity of Fe-N-C with the incorporation of S atoms to engineer carbon support structure and electronic properties of active Fe-N sites simultaneously via a copolymer-assisted synthetic approach. The employment of N,S comonomers significantly increases the numbers of micropores and surface area, enabling dense atomic Fe-N and enhanced utilization efficiency. We report the first-principles calculations reveal that S modulation upraises the Fermi energy of Fe 3d and increases charge density on Fe atoms of Fe-N 4 , thereby enhancing intrinsic catalytic reactivity and selectivity for CO 2 reduction by strengthening the binding interaction between the Fe site and key COOH* intermediate. These integrated structural and electronic merits endow Fe-NS-C with outstanding activity (e.g., CO Faradaic efficiency of 98% at an overpotential of 490 mV) and stability (without deactivation in 30 h), ranking it one of the most active Fe-N-C reported to date. The finding offers an innovative design strategy to enable the design of advanced catalysts for CO 2 conversion.

25 ENERGY STORAGE↗

On the Effect of Small-Angle Scattering by Density Fluctuations on the Efficiency of Linear Transformation of Ordinary and Extraordinary Waves in a Toroidally Inhomogeneous Plasma

We have analyzed the efficiency of tunneling of quasi-optical wave beams through the evanescent region in the vicinity of plasma cutoff in a randomly inhomogeneous magnetoactive plasma. A new theoretical model proposed here makes it possible to study the effect of a random phase modulation induced by density fluctuations in the wave beam path on the efficiency of the linear transformation of waves in the 2D geometry corresponding to the experimental conditions for heating the overdense plasma in toroidal magnetic systems. We have derived a general analytic expression connecting the wave beam coefficient of transformation averaged over the ensemble of random wave field realizations with its phase correlation function. We have analyzed the dependence of the coefficient of transformation on the correlation length for the random phase distribution in the beam and on the traversed path length to the interaction region. The threshold value of the path length above which the fluctuations produce a dominating effect has been determined. The importance of taking into account the 2D effects has been demonstrated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗