Search NASA⌕ Search

SEARCH · Search NASA

Results for “robust parameter design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Towards a Robust Sampling Approach: A Computational Review and Design

As pointed out in several other works, the estimation of the reliability of the electrical grid can not be conducted without the estimation of the stochastic phenomena of electicity demand and electricity production by variable renewable sources. Therefore, sampling procedures have become integral in the design of engineering structures and analysis. Commonly referred to as Monte Carlo uncertainty analysis or integration, the general objective of these procedures is to establish specifics about the uncertainty of an output characteristic of such an engineering system, given uncertainty about its input characteristics. These sampling procedures are applied in a context in which establishing such specifics cannot be performed through other means. Variance-reduction techniques are designed to lessen the variability among estimators to estimate statistics of those output uncertainties. Importance-sampling techniques, on the other hand, are designed to reduce the number of samples needed to estimate a particular statistic—e.g., a tail probability. The combination of these approaches can reduce the computational burden considerably for a particular estimator and statistic. Importance sampling—geared and designed as it is toward improving a particular estimator—suffers, unfortunately, from the unintended consequence of reducing the performance of other estimators in terms of their variance. The objective of this paper is to offer an alternative sampling procedure where this variance does not grow unacceptably large for a suite of estimators. Moreover, it is anticipated that, with additional knowledge of how an engineering output characteristic responds to its input characteristics, tuning parameters of the input’s sampling procedure can be set to improve the output characteristic’s estimation. This work proves the effectiveness of the suggested alternative approach. Such positive outcome will lead to a decrease of the computational burden of performing stochastic optimization of integrated energy systems (e.g., components dispatch, and portfolio composition). In particular, capturing the contribution to the overall system cost of rare and unlikely events and patterns of the electricity demand and production will become less computationally expensive. This is due to the fact that the approach demonstrated here will allow the sampling of those rare occurrences more frequently without misrepresenting their probabilistic impacts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A model to assess Zircaloy’s mechanical property changes following a transient beyond critical heat flux

Maintaining the integrity of nuclear fuel rods is essential for ensuring public health and safety in nuclear power generation. During reactor operation, this integrity is confirmed by demonstrating compliance with established regulatory acceptance criteria. For moderate-frequency events, such as limiting transients and anticipated operational occurrences (AOOs), the current fuel integrity criterion is based on preventing boiling transition. This criterion assumes that prevention of boiling transition will prevent excessive cladding heating and, thus, fuel failure during normal operations. While conservative, this approach places significant constraints on core design, fuel cycle economics, and a plant’s ability to perform major power uprates, leading to suboptimal fuel utilization and inefficient carbon-free energy production. A more efficient approach could be achieved by revising the failure criterion to a material-specific limit rather than strictly preventing the boiling transition, since boiling transition per se is not a cause of fuel cladding failure. Here, as a result, a new licensing framework based on material properties, termed time-at-temperature (t@T), is needed. This approach would allow for brief periods of post–critical heat flux operation during an AOO without compromising safety. Implementing the t@T licensing strategy requires a robust technical foundation in material properties, which must be established through comprehensive data collection on both unirradiated and irradiated fuel and cladding materials. This foundation would enable the development of a safety basis that ensures safe operation while providing greater flexibility and efficiency for reactor operation. This paper documents a thorough review of the available data to establish a baseline knowledge that can inform the development of cladding mechanical models, as well as identify experimental data gaps that need to be addressed in future research. Machine learning and data informatics were utilized to extract the importance of parameters on the t@T parameter. Industry tools were used to perform baseline analyses to define the relevant transient conditions for data analysis. The subsequent review successfully identified applicable experimental data, as well as sufficient data to evaluate changes in cladding mechanical properties following an AOO transient. Rather than developing new models, this work coupled existing irradiation annealing and recrystallization models to calculate changes in hardness, yield stress, and ultimate tensile stress following an AOO event. The findings from this review were summarized to highlight the experimental data needs required to fill remaining gaps and support the development of future t@T licensing methodologies.

Cladding performance↗

CDGPS-Based Relative Navigation for Multiple Spacecraft

This thesis investigates the use of Carrier-phase Differential GPS (CDGPS) in relative navigation filters for formation flying spacecraft. This work analyzes the relationship between the Extended Kalman Filter (EKF) design parameters and the resulting estimation accuracies, and in particular, the effect of the process and measurement noises on the semimajor axis error. This analysis clearly demonstrates that CDGPS-based relative navigation Kalman filters yield good estimation performance without satisfying the strong correlation property that previous work had associated with "good" navigation filters. Several examples are presented to show that the Kalman filter can be forced to create solutions with stronger correlations, but these always result in larger semimajor axis errors. These linear and nonlinear simulations also demonstrated the crucial role of the process noise in determining the semimajor axis knowledge. More sophisticated nonlinear models were included to reduce the propagation error in the estimator, but for long time steps and large separations, the EKF, which only uses a linearized covariance propagation, yielded very poor performance. In contrast, the CDGPS-based Unscented Kalman relative navigation Filter (UKF) handled the dynamic and measurement nonlinearities much better and yielded far superior performance than the EKF. The UKF produced good estimates for scenarios with long baselines and time steps for which the EKF would diverge rapidly. A hardware-in-the-loop testbed that is compatible with the Spirent Simulator at NASA GSFC was developed to provide a very flexible and robust capability for demonstrating CDGPS technologies in closed-loop. This extended previous work to implement the decentralized relative navigation algorithms in real time.

Mitchell, Megan Leigh↗

Error Detection, Factorization and Correction for Multi-View Scene Reconstruction from Aerial Imagery

Scene reconstruction from video sequences has become a prominent computer vision research area in recent years, due to its large number of applications in fields such as security, robotics and virtual reality. Despite recent progress in this field, there are still a number of issues that manifest as incomplete, incorrect or computationally-expensive reconstructions. The engine behind achieving reconstruction is the matching of features between images, where common conditions such as occlusions, lighting changes and texture-less regions can all affect matching accuracy. Subsequent processes that rely on matching accuracy, such as camera parameter estimation, structure computation and non-linear parameter optimization, are also vulnerable to additional sources of error, such as degeneracies and mathematical instability. Detection and correction of errors, along with robustness in parameter solvers, are a must in order to achieve a very accurate final scene reconstruction. However, error detection is in general difficult due to the lack of ground-truth information about the given scene, such as the absolute position of scene points or GPS/IMU coordinates for the camera(s) viewing the scene. In this dissertation, methods are presented for the detection, factorization and correction of error sources present in all stages of a scene reconstruction pipeline from video, in the absence of ground-truth knowledge. Two main applications are discussed. The first set of algorithms derive total structural error measurements after an initial scene structure computation and factorize errors into those related to the underlying feature matching process and those related to camera parameter estimation. A brute-force local correction of inaccurate feature matches is presented, as well as an improved conditioning scheme for non-linear parameter optimization which applies weights on input parameters in proportion to estimated camera parameter errors. Another application is in reconstruction pre-processing, where an algorithm detects and discards frames that would lead to inaccurate feature matching, camera pose estimation degeneracies or mathematical instability in structure computation based on a residual error comparison between two different match motion models. The presented algorithms were designed for aerial video but have been proven to work across different scene types and camera motions, and for both real and synthetic scenes.

42 ENGINEERING↗

${\tt Warm}$SPy: a numerical study of cosmological perturbations in warm inflation

We present ${\tt Warm}$SPy, a numerical code in Python designed to solve for the perturbations' equations in warm inflation models and compute the corresponding scalar power spectrum at CMB horizon crossing. In models of warm inflation, a radiation bath of temperature T during inflation induces a dissipation (friction) rate of strength Q ∝ T c /Φ m in the equation of motion for the inflaton field Φ. While for a temperature-independent dissipation rate (c = 0) an analytic expression for the scalar power spectrum exists, in the case of a non-zero value for c the set of equations can only be solved numerically. For c > 0 (c < 0), the coupling between the perturbations in the inflaton field and radiation induces a growing (decaying) mode in the scalar perturbations, generally parameterized by a multiplicative function G(Q) which we refer to as the scalar dissipation function. Using ${\tt Warm}$SPy, we provide an analytic fit for G(Q) for the cases of c = {3,1,-1}, corresponding to three cases that have been realized in physical models. Compared to previous literature results, our fits are more robust and valid over a broader range of dissipation strengths Q ϵ [10 -7 ,10 4 ]. Additionally, for the first time, we numerically assess the stability of the scalar dissipation function against various model parameters, inflationary histories as well as the effects of metric perturbations. As a whole, the results do not depend appreciably on most of the parameters in the analysis, except for the dissipation index c, providing evidence for the universal behaviour of the scalar dissipation function G(Q).

79 ASTRONOMY AND ASTROPHYSICS↗

Level-2 Milestone 4468: Lorenz Simulation Interface Beta Release

The goal of Lorenz is to develop a sophisticated web-based framework as a front end to Livermore Computing Center resources. The primary features include: a personalized dashboard for each user, giving an at-a-glace overview of all computing center resources; a front-end to job submission and management; and a software framework to extend the convenience of web interfaces into simulation codes, including support for setting up, launching, steering, and monitoring simulations. Because the breadth of desktop operating systems in use both inside and outside LLNL spans all flavors of Linux, Mac, and Windows, the decision was made to use exclusively web-based technologies in Lorenz. Recent advancements in AJAX and Javascript programming, along with coming advances in the form of HTML5 and CSS3, made the browser the preferred development platform. The goal is to provide the user with a robust application interface that requires nothing more than a modern, standards-based web browser. This approach not only provides convenient access to Lorenz for internal and external users, but also has significant advantages over conventional applications in terms of rapid deployment and updates. The first phase of the Lorenz project is a system “dashboard”, known as MyLC, that gives LC users a rich set of portal applications, or “portlets”, from which to choose. Information that previously required knowledge of dozens of different commands, files, and web pages is now available in one convenient location. This includes account information, bank and disk usage, quotas, cluster utilization, news items, active jobs on LC systems, and more. The extensible software design of the dashboard allows users and staff members to develop their own portlets, and for them to be shared with all users or just within work groups. The second major phase of Lorenz was built on the idea that HPC centers are managed around batch processing, and “jobs” (or “runs”) progress through several discrete stages: setup, submission, queuing/waiting, running, completion, analysis, and archiving. Lorenz aims to ultimately tie all of these pieces together, including integration with the dashboard and application portals. In addition to helping guide users through the process of defining batch parameters, monitoring job progress, and interacting with jobs and job output, Lorenz also aims to promote access to additional tools and capabilities which to this point have been limited to use by power users. Ultimately Lorenz will assist users in choosing the appropriate resources, such as cluster and file system, given the requirements of a job. The third major phase of Lorenz, the subject of this milestone, is the development of an application portal. This involves teaming with application codes to provide a simple graphical interface to the simulations, which in turn seamlessly ties into job submission and monitoring. This will allow users to directly define simulation parameters and launch applications using a simple but powerful web front-end. Because many complex multi-physics codes can have thousands of inputs, providing a general GUI for building an input deck from scratch is impractical. However, most users of large applications start with an existing input file, and make some number of small changes to it. The application portal will feature a process that combines trusted and validated input files with a GUI that guides the user toward making the relatively minor changes needed for their particular problem. The input files will be in the form of templates, containing most of the data needed for a particular problem along with parameterization of changeable inputs. For expert users, there ultimately will be a way to edit the final input file directly - in the event that there are input changes needed that were not captured in the GUI.

97 MATHEMATICS AND COMPUTING↗

PPPL Report on Reduced Modeling of Fusion Alpha Transport in ARC Burning Plasmas

We are reporting on the modeling of fusion alpha particle transport in the planned ARC fusion device being designed by the CFS (Commonwealth Fusion Systems: https://cfs.energy). The ARC tokamak is designed to operate in a burning-plasma regime characterized by a substantial population of fusion-born alpha particles. Alfvén eigenmode (AE) stability is assessed both analytically and numerically, incorporating alpha-particle drive, ion Landau, and radiative damping from thermal species and collisional damping from trapped electrons. Regions of unstable and near-threshold AE activity are mapped across ARC’s operational parameter space. Linear stability analysis with NOVA indicates multiple, often marginally unstable AEs, extending to toroidal mode numbers up to n= 30. The present report focuses on the ARC flat-top operating point prior to the sawtooth event. Alpha-particle transport on timescales exceeding the neoclassical slowing-down time is assessed using the NUBEAM module [1][2] of the TRANSP code [3], employing transport coefficients derived from the RBQ quasilinear modeling (cf. Appendix B). These global simulations identify favorable and unfavorable operating regimes with respect to alpha confinement, pressure redistribution, and overall alpha-heating efficiency. We also evaluate additional transport mechanisms—including neoclassical tearing mode (TM)–induced stochasticity, sawtooth-driven redistribution, and toroidal-field ripple using the kick model (cf. Appendix C) which makes use of the guiding-center code ORBIT, see Section 5. The kick model is integrated into TRANSP to enable self-consistent predictions of alpha-driven current formation and sustainment within the ARC scenario. Sensitivity scans are performed over the mode frequency, rational-surface alignment, island width, mode amplitude, and proximity of the limiter to the plasma. Our study provides an initial, physics-based guidance for machine design, operational planning, and equilibrium control, ensuring adequate alpha confinement and robust self-heating performance in ARC. Our simulations mostly targeted worst case scenarios, e.g. for TMs and sawteeth. Overall, we expect benign effects for the ARC scenario investigated in this work on fusion alpha confinement and losses in the presence of AEs, tearing modes and sawteeth. This report addresses three thrusts identified at the outset. The first thrust focuses on analytic estimates of the parametric dependencies of EP relaxation based on local AE stability simulations (Section 3). The second thrust involves global evaluations of AE stability using the NOVA, RBQ, and NUBEAM codes (Section 4). Finally, we investigate alpha-particle transport driven by low-frequency instabilities associated with sawteeth and tearing modes (Section 5).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Using dorsal surface for individual identification of dairy calves through 3D deep learning algorithms

Advances in machine learning techniques have allowed the development of computer vision systems (CVS) that can accurately predict several phenotypes of interest for livestock operations. In this context, 3D images taken from a top-down view are particularly useful for estimating body condition score, growth development, and body biometrics in cattle. Frequently, such CVS rely on identification (ID) systems, such as electronic tags, as a way to match animal ID and the predicted phenotype. However, the same 3D images used to predict body weight and other animal biometrics could be adopted for animal recognition as well. Such alternative would optimize CVS to recognize animal ID and monitor growth development simultaneously while leveraging the same hardware infrastructure. Furthermore, this strategy could be used to recognize animals with similar color patterns. Nonetheless, growing animals are continuously changing body shape, which could limit its use as an invariant feature for pattern recognition. Thus, the objectives of this study were: (1) to compare algorithms for different 3D object representations to identify individual animals; and (2) to evaluate how short-term changes in body shape due to animal growth affect the predictive performance of these algorithms. For objective 1, the algorithms were trained (n = 4,558) and tested (n = 1,139) using images from 38 Holstein calves. For objective 2, we designed three different experiments using images (n = 2,347) from five Holstein calves taken over six weeks during their growing period, always training and testing on different weeks. Each experiment evaluated how changing a different parameter of the image capturing procedure affected the predictive ability of the trained algorithms. In the first experiment, we varied the total number of images per animal in the training set; in the second experiment, we varied the number of weeks while keeping a fixed number of images in the training set; and in the third experiment, we skipped weeks between images in the training and test sets. The F 1 score for objective (1) was up to 0.804 when testing with the last frames of each video, and up to 0.959 when using random frames for testing. For objective (2), the F 1 score was up to 0.947 for the first experiment when using 130 images per animal; up to 0.979 for the second experiment when using all five weeks; and up to 0.917 when not skipping weeks between training and testing. In conclusion, these results show that deep learning algorithms can be used to identify individual animals through their dorsal area 3D surfaces, and, from our experiments using calves in their growing period, that they are robust enough to account for changes in body shape and size, making them a promising tool for animal recognition during growth.

3D neural networks↗

Miniature L-Band Radar Transceiver

A miniature L-band transceiver that operates at a carrier frequency of 1.25 GHz has been developed as part of a generic radar electronics module (REM) that would constitute one unit in an array of many identical units in a very-large-aperture phased-array antenna. NASA and the Department of Defense are considering the deployment of such antennas in outer space; the underlying principles of operation, and some of those of design, also are applicable on Earth. The large dimensions of the antennas make it advantageous to distribute radio-frequency electronic circuitry into elements of the arrays. The design of the REM is intended to implement the distribution. The design also reflects a requirement to minimize the size and weight of the circuitry in order to minimize the weight of any such antenna. Other requirements include making the transceiver robust and radiation-hard and minimizing power demand. Figure 1 depicts the functional blocks of the REM, including the L-band transceiver. The key functions of the REM include signal generation, frequency translation, amplification, detection, handling of data, and radar control and timing. An arbitrary-waveform generator that includes logic circuitry and a digital-to-analog converter (DAC) generates a linear-frequency-modulation chirp waveform. A frequency synthesizer produces local-oscillator signals used for frequency conversion and clock signals for the arbitrary-waveform generator, for a digitizer [that is, an analog-to-digital converter (ADC)], and for a control and timing unit. Digital functions include command, timing, telemetry, filtering, and high-rate framing and serialization of data for a high-speed scientific-data interface. The aforementioned digital implementation of filtering is a key feature of the REM architecture. Digital filters, in contradistinction to analog ones, provide consistent and temperature-independent performance, which is particularly important when REMs are distributed throughout a large array. Digital filtering also enables selection among multiple filter parameters as required for different radar operating modes. After digital filtering, data are decimated appropriately in order to minimize the data rate out of an antenna panel. The L-band transceiver (see Figure 2) includes a radio-frequency (RF)-to-baseband down-converter chain and an intermediate- frequency (IF)-to-RF up-converter chain. Transmit/receive (T/R) switches enable the use of a single feed to the antenna for both transmission and reception. The T/R switches also afford a built-in test capability by enabling injection of a calibration signal into the receiver chain. In order of decreasing priority, components of the transceiver were selected according to requirements of radiation hardness, then compactness, then low power. All of the RF components are radiation-hard. The noise figure (NF) was optimized to the extent that (1) a low-noise amplifier (LNA) (characterized by NF < 2 dB) was selected but (2) the receiver front-end T/R switches were selected for a high degree of isolation and acceptably low loss, regardless of the requirement to minimize noise.

McWatters, Dalia↗

A robust and efficient stepwise regression method for building sparse polynomial chaos expansions

Polynomial Chaos (PC) expansions are widely used in various engineering fields for quantifying uncertainties arising from uncertain parameters. The computational cost of classical PC solution schemes is unaffordable as the number of deterministic simulations to be calculated grows dramatically with the number of stochastic dimension. This considerably restricts the practical use of PC at the industrial level. A common approach to address such problems is to make use of sparse PC expansions. This paper presents a non-intrusive regression-based method for building sparse PC expansions. The most important PC contributions are detected sequentially through an automatic search procedure. The variable selection criterion is based on efficient tools relevant to probabilistic method. Two benchmark analytical functions are used to validate the proposed algorithm. The computational efficiency of the method is then illustrated by a more realistic CFD application, consisting of the non-deterministic flow around a transonic airfoil subject to geometrical uncertainties. To assess the performance of the developed methodology, a detailed comparison is made with the well established LAR-based selection technique. The results show that the developed sparse regression technique is able to identify the most significant PC contributions describing the problem. Moreover, the most important stochastic features are captured at a reduced computational cost compared to the LAR method. The results also demonstrate the superior robustness of the method by repeating the analyses using random experimental designs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Results for Phase I of the IAEA Coordinated Research Program on HTGR Uncertainties

The quantification of uncertainties in design and safety analysis of reactors is today not only broadly accepted, but in many cases became the preferred way to replace traditional conservative analysis for safety and licensing analysis. The use of a more fundamental methodology is also consistent with the reliable high fidelity physics models and robust, efficient, and accurate codes available today. To facilitate uncertainty analysis applications a comprehensive approach and methodology must be developed and applied. High Temperature Gas-cooled Reactors (HTGR) has its own peculiarities, coated particle design, large graphite quantities, different materials and high temperatures that also require other simulation requirements. The IAEA has therefore launched a Coordinated Research Project (CRP) on the HTGR Uncertainty Analysis in Modeling (UAM) in 2013 to study uncertainty propagation specifically in the HTGR analysis chain. Two benchmark problems are defined, with the prismatic design represented by the General Atomics (GA) MHTGR-350 and a 250 MW modular pebble bed design similar to the HTR-PM (INET, China). This report summarizes the contributions of the HTGR Methods Simulation group at Idaho National Laboratory (INL) up to this point of the CRP. The activities at INL have been focused so far on creating the problem specifications for the prismatic design, as well as providing reference solutions for the exercises defined for Phase I. An overview is provided of the HTGR UAM objectives and scope, and the detailed specifications for Exercises I-1, I-2, I-3 and I-4 are also included here for completeness. The main focus of the report is the compilation and discussion of reference results for Phase I (i.e. for input parameters at their nominal or best-estimate values), which is defined as the first step of the uncertainty quantification process. These reference results can be used by other CRP participants for comparison with other codes or their own reference results. The status on the Monte Carlo modeling of the experimental VHTRC facility is also discussed. Reference results were obtained for the neutronics stand-alone cases (Ex. I-1 and Ex. I-2) using the (relatively new) Monte Carlo code Serpent, and comparisons were performed with the more established Monte Carlo codes MCNP and KENO-VI. For the thermal-fluids stand-alone cases (Ex. I-3 and I-4) the commercial CFD code CFX was utilized to obtain reference results that can be compared with lower fidelity tools.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The AGORA High-resolution Galaxy Simulations Comparison Project. III. Cosmological Zoom-in Simulation of a Milky Way–mass Halo

In this work, we present a suite of high-resolution cosmological zoom-in simulations to z = 4 of a 10 12 M⊙ halo at z = 0, obtained using seven contemporary astrophysical simulation codes (Art-I, Enzo, Ramses, Changa, Gadget-3, Gear, and Gizmo) widely used in the numerical galaxy formation community. The physics prescriptions for gas cooling and heating and star formation are the same as the ones used in our previous Assembling Galaxies of Resolved Anatomy (AGORA) disk comparison but now account for the effects of cosmological processes such as the expansion of the universe, intergalactic gas inflow, and the cosmic ultraviolet background radiation emitted by massive stars and quasars. In this work, we introduce the most careful comparison yet of galaxy formation simulations run by different code groups, together with a series of four calibration steps each of which is designed to reduce the number of tunable simulation parameters adopted in the final run. In the first two steps, we methodically calibrate the gas physics, such as cooling and heating, in simulations without star formation. In the third step, we seek agreement on the total stellar mass produced with the common star formation prescription used in the AGORA disk comparison, in stellar-feedback-free simulations. In the last calibration step, we activate stellar feedback, where each code group is asked to set the feedback prescription to as close to the most widely used one in its code community as possible, while aiming for convergence in the stellar mass at z = 4 to the values predicted by semiempirical models. After all the participating code groups successfully complete the calibration steps, we achieve a suite of cosmological simulations with similar mass assembly histories down to z = 4. With numerical accuracy that resolves the internal structure of a target halo (≲100 physical pc at z = 4), we find that the codes overall agree well with one another, e.g., in gas and stellar properties, but also show differences, e.g., in circumgalactic medium (CGM) properties. We argue that, if adequately tested in accordance with our proposed calibration steps and common parameters, high-resolution cosmological zoom-in simulations can have robust and reproducible results. New code groups are invited to join and enrich this comparison by generating equivalent models or to test the code's compatibility on their own, by adopting the common initial conditions, the common easy-to-implement physics package, and the proposed calibration steps. Further analyses of the zoom-in simulations presented here will be presented in forthcoming reports from the AGORA Collaboration, including studies of the CGM, simulations by additional codes, and results at lower redshift.

79 ASTRONOMY AND ASTROPHYSICS↗

Global optimization of data quality checks on 2-D and 3-D networks of GPR cross-well tomographic data for automatic correction of unknown well deviations

Significant errors related to poor time zero estimation, well deviation or mislocation of the transmitter (TX) and receiver (RX) stations can render even the most sophisticated modeling and inversion routine useless. Previous examples of methods for the analysis and correction of data errors in geophysical tomography include the works of Maurer and Green (1997), Squires et al. (1992) and Peterson (2001). Here we follow the analysis and techniques of Peterson (2001) for data quality control and error correction. Through our data acquisition and quality control procedures we have very accurate control on the surface locations of wells, the travel distance of both the transmitter and receiver within the boreholes, and the change in apparent zero time. However, we often have poor control on well deviations, either because of economic constraints or the nature of the borehole itself prevented the acquisition of well deviation logs. Also, well deviation logs can sometimes have significant errors. Problems with borehole deviations can be diagnosed prior to inversion of travel-time tomography data sets by plotting the apparent velocity of a straight ray connecting a transmitter (TX) to a receiver (RX) against the take-off angle of the ray. Issues with the time-zero pick or distances between wells appear as symmetric smiles or frown in these QC plots. Well deviation or dipping-strong anisotropy will result in an asymmetric correlation between apparent velocity and take-off angle (Figure 1-B). In addition, when a network of interconnected GPR tomography data is available, one has the additional quality constraint of insuring that there is continuity in velocity between immediately adjacent tomograms. A sudden shift in the mean velocity indicates that either position deviations are present or there is a shift in the pick times. Small errors in well geometry may be effectively treated during inversion by including weighting, or relaxation, parameters into the inversion (e.g. Bautu et al., 2006). In the technique of algebraic reconstruction tomography (ART), which is used herein for the travel time inversion (Peterson et al., 1985), a small relaxation parameter will smooth imaging artifacts caused by data errors at the expense of resolution and contrast (Figure 2). However, large data errors such as unaccounted well deviations cannot be adequately suppressed through inversion weighting schemes. Previously, problems with tomograms were treated manually. However, in large data sets and/or networks of data sets, trial and error changes to well geometries become increasingly difficult and ineffective. Mislocation of the transmitter and receiver stations of GPR cross-well tomography data sets can lead to serious imaging artifacts if not accounted for prior to inversion. Previously, problems with tomograms have been treated manually prior to inversion. In large data sets and/or networks of tomographic data sets, trial and error changes to well geometries become increasingly difficult and ineffective. Our approach is to use cross-well data quality checks and a simplified model of borehole deviation with particle swarm optimization (PSO) to automatically correct for source and receiver locations prior to tomographic inversion. We present a simple model of well deviation, which is designed to minimize potential corruption of actual data trends. We also provide quantitative quality control measures based on minimizing correlations between take-off angle and apparent velocity, and a quality check on the continuity of velocity between adjacent wells. This methodology is shown to be accurate and robust for simple 2-D synthetic test cases. Plus, we demonstrate the method on actual field data where it is compared to deviation logs. This study shows the promise for automatic correction of well deviations in GPR tomographic data. Analysis of synthetic data shows that very precise estimates of well deviation can be made for small deviations, even in the presence of static data errors. However, the analysis of the synthetic data and the application of the method to a large network of field data show that the technique is sensitive to data errors varying between neighboring tomograms.

54 ENVIRONMENTAL SCIENCES↗

Scale-up Testing—Foam as A Remedial Amendment Carrier - 11029

This paper describes results from intermediate-scale, two-dimensional testing of foam injection into sedimentary materials collected from the U.S. Department of Energy (DOE) Hanford Site area. The testing was performed to evaluate the transport of new, more robust, foam generation formulas developed by PNNL on field applicability. The mechanisms of transport , foam stability, delivery pressure, foam migration and the ability of foam to deliver remedial amendments for stabilization of uranium contamination were evaluated. Testing was accomplished in a test bed that is designed to focus on two-dimensional flow, in the form of two, thin rectangular boxes. Each of the boxes holds approximately 135 liters (255 kilograms) of sediment. A total of six sets of tests have been conducted, the last two of which will be described here. During the fifth and sixth tests, foam, generated by means of mechanical blending, was injected into the central screened segment of the left side of each box while air was extracted from multiple screened segments along the right side of each box. During these two tests both of the boxes were loaded to contain a rectangular zones of fine material and a rectangular zone of coarse material . Portions of the sediment were augmented with uranium-rich calcite to produce known concentrations of uranium. The foam generating formulas used in both tests contained sodium phosphate and sodium tripolyphosphate as a remedial amendment. Subsequent to each of the two tests, the test beds were disassembled, and samples of the sediments were taken and analyzed for a number of parameters, depending on the specific test. The data indicated that uranium contamination may be successfully immobilized and that that directional movement of the injected foam can be controlled.

Foam↗

Searching for primordial non-Gaussianity in Planck CMB maps using a combined estimator

The extensive search for deviations from Gaussianity in cosmic microwave background radiation (CMB) data is very important due to the information about the very early moments of the universe encoded there. Recent analyses from Planck CMB data do not exclude the presence of non-Gaussianity of small amplitude, although they are consistent with the Gaussian hypothesis. The use of different techniques is essential to provide information about types and amplitudes of non-Gaussianities in the CMB data. In particular, we find interesting to construct an estimator based upon the combination of two powerful statistical tools that appears to be sensitive enough to detect tiny deviations from Gaussianity in CMB maps. This estimator combines the Minkowski functionals with a Neural Network, maximizing a tool widely used to study non-Gaussian signals with a reinforcement of another tool designed to identify patterns in a data set. We test our estimator by analyzing simulated CMB maps contaminated with different amounts of local primordial non-Gaussianity quantified by the dimensionless parameter f{sub NL}. We apply it to these sets of CMB maps and find ∼> 98% of chance of positive detection, even for small intensity local non-Gaussianity like f{sub NL} = 38±18, the current limit from Planck data for large angular scales. Additionally, we test the suitability to distinguish between primary and secondary non-Gaussianities: first we train the Neural Network with two sets, one of nearly Gaussian CMB maps (|f{sub NL}| ≤ 10) but contaminated with realistic inhomogeneous Planck noise (i.e., secondary non-Gaussianity) and the other of non-Gaussian CMB maps, that is, maps endowed with weak primordial non-Gaussianity (28 ≤ f{sub NL} ≤ 48); after that we test an ensemble composed of CMB maps either with one of these non-Gaussian contaminations, and find out that our method successfully classifies ∼ 95% of the tested maps as being CMB maps containing primordial or secondary non-Gaussianity. Furthermore, we analyze the foreground-cleaned Planck maps obtaining constraints for non-Gaussianity at large-angles that are in good agreement with recent constraints. Finally, we also test the robustness of our estimator including cut-sky masks and realistic noise maps measured by Planck, obtaining successful results as well.

79 ASTRONOMY AND ASTROPHYSICS↗

SAR terrain classifier and mapper of biophysical attributes

In preparation for the launch of SIR-C/X-SAR and design studies for future orbital SAR, a program has made considerable progress in the development of an SAR terrain classifier and algorithms for quantification of biophysical attributes. The goal of this program is to produce a generalized software package for terrain classification and estimation of biophysical attributes and to make this package available to the larger scientific community. The basic elements of the SAR (Synthetic Aperture Radar) terrain classifier are outlined. An SAR image is calibrated with respect to known system and processor gains and external targets (if available). A Level 1 classifier operates on the data to differentiate: urban features, surfaces and tall and short vegetation. Level 2 classifiers further subdivide these classes on the basis of structure. Finally, biophysical and geophysical inversions are applied to each class to estimate attributes of interest. The process used to develop the classifiers and inversions is shown. Radar scattering models developed from theory and from empirical data obtained by truck-mounted polarimeters and the JPL AirSAR are validated. The validated models are used in sensitivity studies to understand the roles of various scattering sources (i.e., surface trunk, branches, etc.) in determining net backscatter. Model simulations of sigma (sup o) as functions of the wave parameters (lambda, polarization and angle of incidence) and the geophysical and biophysical attributes are used to develop robust classifiers. The classifiers are validated using available AirSAR data sets. Specific estimators are developed for each class on the basis of the scattering models and empirical data sets. The candidate algorithms are tested with the AirSAR data sets. The attributes of interest include: total above ground biomass, woody biomass, soil moisture and soil roughness.

Ulaby, Fawwaz T.↗

Impact and Crashworthiness Characteristics of Venera Type Landers for Future Venus Missions

In this paper an in-depth investigation of the structural design of the Venera 9-14 landers is explored. A complete reverse engineering of the Venera lander was required. The lander was broken down into its fundamental components and analyzed. This provided in-sights into the hidden features of the design. A trade study was performed to find the sensitivity of the lander's overall mass to the variation of several key parameters. For the lander's legs, the location, length, configuration, and number are all parameterized. The size of the impact ring, the radius of the drag plate, and other design features are also parameterized, and all of these features were correlated to the change of mass of the lander. A multi-fidelity design tool used for further investigation of the parameterized lander was developed. As a design was passed down from one level to the next, the fidelity, complexity, accuracy, and run time of the model increased. The low-fidelity model was a highly nonlinear analytical model developed to rapidly predict the mass of each design. The medium and high fidelity models utilized an explicit finite element framework to investigate the performance of various landers upon impact with the surface under a range of landing conditions. This methodology allowed for a large variety of designs to be investigated by the analytical model, which identified designs with the optimum structural mass to payload ratio. As promising designs emerged, investigations in the following higher fidelity models were focused on establishing their reliability and crashworthiness. The developed design tool efficiently modelled and tested the best concepts for any scenario based on critical Venusian mission requirements and constraints. Through this program, the strengths and weaknesses inherent in the Venera-Type landers were thoroughly investigated. Key features identified for the design of robust landers will be used as foundations for the development of the next generation of landers for future exploration missions to Venus.

Schroeder, Kevin↗

Asi Nuclear Energy Sensors Data Portal Chatbot And Data Structuring Tool

The Idaho National Laboratory (INL) is advancing the development of an AI-powered chatbot and data structuring tool specifically designed to accelerate data mining processes for sensor-related information and seamlessly integrate the results into the ASI Sensors Data Portal (https://nes.energy.gov/). By doing so, the software aims to enhance the accessibility, usability, and organization of sensor data for nuclear energy applications. The software initial phase focuses on retrieving comprehensive datasets, prioritizing the past five years of publicly available information from the Office of Scientific and Technical Information (OSTI). These datasets will be meticulously processed to ensure compatibility, employing cleaning and preprocessing steps to eliminate irrelevant, incomplete, or corrupted information, thus establishing a robust foundation for subsequent AI use. The data will serve as the backbone for training an AI model and chatbot, which will act as an interactive tool enabling users to ask complex, context-specific questions and receive accurate, validated answers derived from constrained literature. In parallel, the project incorporates a data structuring process supported by AI to organize sensor information from multiple sources into a standardized format. This structured data will include detailed sensor specifications, such as measurement range, applications, accuracy, and operating conditions, generated and documented with AI. These specifications will be systematically integrated into the sensor portal. To maintain the highest levels of accuracy and relevance, all AI-generated outputs will be reviewed and validated by subject matter experts (SMEs), with additional fields or parameters added as needed. Future stages of the project aim to expand the dataset beyond OSTI to include other sources and potentially incorporate unclassified controlled information (UCI) with restricted access protocols to address security and confidentiality requirements.

Mapes, NormanJ. [Idaho National Laboratory (INL), ↗