Search NASA⌕ Search

SEARCH · Search NASA

Results for “Amorphous”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Characterization of Electronic Transport through Amorphous TiO 2 Produced by Atomic Layer Deposition

Electrical transport in amorphous titanium dioxide (a-TiO 2 ) thin films, deposited by atomic layer deposition (ALD), and across heterojunctions of p + -Si|a-TiO 2 |metal substrates that had various top metal contacts has been characterized by ac conductivity, temperature-dependent dc conductivity, space-charge-limited current spectroscopy, electron paramagnetic resonance (EPR) spectroscopy, X-ray photoelectron spectroscopy, and current density versus voltage ( J – V ) characteristics. Amorphous TiO 2 films were fabricated using either tetrakis(dimethylamido)-titanium with a substrate temperature of 150 °C or TiCl 4 with a substrate temperature of 50, 100, or 150 °C. EPR spectroscopy of the films showed that the Ti 3+ concentration varied with the deposition conditions and increases in the concentration of Ti 3+ in the films correlated with increases in film conductivity. Valence band spectra for the a-TiO 2 films exhibited a defect-state peak below the conduction band minimum (CBM) and increases in the intensity of this peak correlated with increases in the Ti 3+ concentration measured by EPR as well as with increases in film conductivity. The temperature-dependent conduction data exhibited Arrhenius behavior at room temperature with an activation energy that decreased with decreasing temperature, suggesting that conduction did not occur primarily through either the valence or conduction bands. The information from all of the measurements are consistent with a Ti 3+ defect-mediated transport mode involving a hopping mechanism with a defect density of 10 19 cm –3 , a 0.83 wide defect band centered 1.47 eV below the CBM, and a free-electron concentration of 10 16 cm –3 . The data are consistent with substantial room-temperature anodic conductivity resulting from the introduction of defect states during the ALD fabrication process as opposed to charge transport intrinsically associated with the conduction band of TiO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ultrathin Amorphous Titania on Nanowires: Optimization of Conformal Growth and Elucidation of Atomic-Scale Motifs

Due to its chemical stability, titania (TiO 2 ) thin films increasingly have significant impact when applied as passivation layers. However, optimization of growth conditions, key to achieving essential film quality and effectiveness, is challenging in the few-nanometers thickness regime. Furthermore, the atomic-scale structure of the nominally amorphous titania coating layers, particularly when applied to nanostructured supports, is difficult to probe. In this Letter, the quality of titania layers grown on ZnO nanowires is optimized using specific strategies for processing of the nanowire cores prior to titania coating. The best approach, low-pressure O 2 plasma treatment, results in significantly more-uniform titania films and a conformal coating. Characterization using X-ray absorption near edge structure (XANES) reveals the titania layer to be highly amorphous, with features in the Ti spectra significantly different from those observed for bulk TiO 2 polymorphs. Analysis based on first-principles calculations suggests that the titania shell contains a substantial fraction of under-coordinated Ti 4+ ions. The best match to the experimental XANES spectrum is achieved with a “glassy” TiO 2 model that contains ~50% of under-coordinated Ti 4+ ions, in contrast to bulk crystalline TiO 2 that only contains 6-coordinated Ti 4+ ions in octahedral sites.

36 MATERIALS SCIENCE↗

Plasma Synthesis of Spherical Crystalline and Amorphous Electrolyte Nanopowders for Solid-State Batteries

Here, we demonstrate the theory-guided plasma synthesis of high purity nanocrystalline Li 3.5 Si 0.5 P 0.5 O 4 and fully amorphous Li 2.7 Si 0.7 P 0.3 O 3.17 N 0.22 . The synthesis involves the injection of single or mixed phase precursors directly into a plasma torch. As the material exits the plasma torch, it is quenched into spherical nanocrystalline or amorphous nanopowders. This process has virtually zero Li loss and allows for the inclusion of N, which is not accessible with traditional synthesis methods. Finally, we further demonstrate the ability to sinter the crystalline nanopowder into a dense electrolyte membrane at 800 °C, well below the traditional 1000 °C required for a conventional Li 3.5 Si 0.5 P 0.5 O 4 powder.

25 ENERGY STORAGE↗

Mesoporous Amorphous High-Entropy Oxide Films: Unlocking Enhanced Redox Activity

High-entropy oxides (HEOs) represent a frontier in catalyst design via entropy-stabilized solid solution formation. However, their catalytic efficiency is limited by their bulk and dense nature. This work presents a strategic approach to tackle this challenge by fabricating mesoporous amorphous HEO films (MA-HEOF) possessing maximized active site utilization efficiency. The success hinges on the as-developed geometric engineering strategy via controlled deposition–precipitation to confine the amorphous HEO thin film on the surface of mesoporous channels. The unique structure of MA-HEOF was elucidated via microscopy-, X-ray-, and neutron-based techniques, which were manifested by enriched surface-activated lattice oxygen and enhanced redox activity, as confirmed by isotope studies. Besides, the MA-HEOF could stabilize and modulate the properties of integrated noble metal sites, enhancing their redox activity in diverse reactions. In conclusion, the approaches and insights presented herein provide guidance on maximizing the utilization efficiency of high-entropy materials in catalysis and beyond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal and Non-thermal Physiochemical Processes in Nanoscale Films of Amorphous Solid Water

Amorphous solid water (ASW) is a metastable form of water created by vapor deposition onto a cold substrate (typically less than 130 K). Since this unusual form of water only exists on earth in laboratories with highly specialized equipment, it is fair to ask why there is any interest in studying this esoteric material. Much of the scientific interest involves using ASW as a model system to explore the physical and reactive properties of liquid water and aqueous solutions. Other researchers are interested in ASW because it is believed to be the predominate form of water in the extreme cold temperatures found in many astrophysical and planetary environments. In addition, ASW is a convenient model system for studying the stability of metastable systems (glasses) and the properties of highly porous materials. A fundamental understanding of such properties has applications in a diverse range of disciplines including cryobiology, food science, pharmaceuticals, astrophysics and nuclear waste storage among others.There exist several excellent reviews on the properties of ASW and supercooled liquid water and a new comprehensive review is beyond the scope of this Account. Instead, we focus on our research over the past 15 years using molecular beams and surface science techniques to probe the thermal and non thermal properties of nanoscale films of ASW. We use molecular beams to precisely control the deposition conditions (flux, incident, energy, incident angle) to create compositionally-tailored, nanoscale films of ASW at low temperatures. To study the transport properties (viscosity, diffusivity), the amorphous films can be heated above their glass transition temperatures, Tg, at which time they transform into deeply supercooled liquids prior to crystallization. The advantage of this approach is that at temperatures near Tg the viscosity is approximately 15 orders of magnitude larger than a normal liquid, and therefore the crystallization kinetics are dramatically slowed, increasing the time available for experiments. For example, near Tg, on a typical laboratory time scale (e.g. {approx}1000 s), a water molecule moves less than a molecular distance. For this reason, nanoscale films help to probe the behavior and reactions of supercooled liquid at these low temperatures. ASW films can be used for investigating the non-thermal reactions relevant to radiolysis. In this account we will present a survey of our research on the thermal and non thermal properties of ASW using this approach.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Nanoporous Structure and Medium-Range Order in Synthetic Amorphous Calcium Carbonate

We adopt a reverse Monte Carlo refinement approach, using experimental X-ray total scattering data, to develop a structure model for synthetic, hydrated amorphous calcium carbonate (ACC). The ACC is revealed to consist of a porous calcium-rich framework that supports interconnected channels containing water and carbonate molecules. The existence of a previously unrecognized nanometer-scale channel network suggests mechanisms of how additives can be accommodated within the structure and provide temporary stabilization, as well as influence the crystallization process. Moreover, while lacking long-range order, the calcium-rich framework in the ACC contains similar Ca packing density to that present in calcite, aragonite, and vaterite, yielding clues of how the amorphous material converts into the different crystalline forms. Our results provide a new starting point for advancing our understanding of biomineralization as well as the development of biomimetic approaches to next-generation materials synthesis.

58 GEOSCIENCES↗

Pressure-induced amorphization and porosity modification in a metal-organic framework.

The impact of modest, industrially accessible pressures (0-1.2 GPa) on the structure and porosity of the zeolitic imidazolate framework Zn(2-methylimidazole){sub 2}, ZIF-8, was investigated using in situ powder X-ray diffraction in combination with sorption measurements for pressure-treated samples. The framework is highly compressible, with a bulk modulus (K = -V {partial_derivative}P/{partial_derivative}V) of 6.52(35) GPa, the most compressible metal-organic framework (MOF) documented to date. The framework undergoes an irreversible pressure-induced amorphization following compression beyond 0.34 GPa. The pressure-amorphized ZIF-8 remains porous, although the sorption characteristics are distinctly altered compared to the pristine material. As such, pressure can provide a new route to systematically modify the sorption behavior and other functional properties of MOFs, a nontraditional form of postsynthetic modification. Importantly, pressure modification of MOFs is effective at lower pressures than in other porous materials (e.g., zeolites) and, as such, is easily scalable and industrially relevant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Coupling Amorphization and Compositional Optimization of Ternary Metal Phosphides toward High-Performance Electrocatalytic Hydrogen Production

Amorphous materials, with abundant active sites and unique electronic configurations, have the potential to outperform their crystalline counterparts in high-performance catalysis for clean energy. However, their synthesis and compositional optimization remain underexplored due to the strict conditions required for their formation. Here, in this study, we report the synthesis of ternary platinum-nickel-phosphorus (PtNiP) amorphous nanoparticles (ANPs) within milliseconds by flash Joule heating, which features ultrafast cooling that enables the vitrification of metal precursors. Through compositional optimization, the Gibbs free energy of hydrogen adsorption for Pt 4 Ni 4 P 1 ANPs is optimized at 0.02 eV, an almost ideal value, even surpassing that of the benchmark metallic platinum catalyst. As a result, the PtNiP ANPs exhibited superior activity in electrocatalytic hydrogen evolution in acid electrolyte (η 10 ∼ 14 mV, Tafel slope ∼ 18 mV dec –1 , and mass activity 5× higher than state-of-the-art Pt/C). Life-cycle assessment and technoeconomic analysis suggest that, compared to existing processes, our approach enables notable reductions in greenhouse gas emission, energy consumption, and production cost for practical electrolyzer catalyst manufacturing.

36 MATERIALS SCIENCE↗

Low-Temperature Pyrolysis of Aliphatic Polymers Using a Fluorinated Amorphous Silica–Alumina: Cooperative Reactivity between a Redox-Active Radical and an Aluminum Lewis Site

Fluorinated amorphous silica–alumina (F-ASA) prepared by the thermolysis of Krossing’s Al(OC(CF 3 ) 3 ) 3 (PhF) Lewis superacid supported on silica is a very reactive catalyst that promotes the pyrolysis (cracking) of aliphatic polymer melts to produce low molecular weight hyperbranched oils. Initial spectroscopic studies reported previously (Gao, J.; Perras, F. A.; Conley, M. P. J. Am. Chem. Soc . 2025 , 147, 18145–18154) showed that this material contains a distribution of four-, five-, and six-coordinate aluminum sites and a small amount of Brønsted acid sites, similar to typical amorphous silica–alumina materials that are far less reactive in the pyrolysis of aliphatic polymer melts. The objective of this study was to determine whether other active sites present in F-ASA could facilitate pyrolysis reactions. This study provides evidence for the presence of a redox-active silicon oxycarbide persistent radical ((≡Si) 3 C•) in F-ASA. Mims ENDOR EPR experiments show that (≡Si) 3 C• is located close to aluminum. Contacting F-ASA with thianthrene (Th) results in oxidation to form the [Th •+ ][F–ASA] ion-pair, while reactions with 1-hydroxy-2,2,6,6-tetramethylpiperidine (TEMPOH) result in H atom transfer to form TEMPO radical and F-ASA-H containing a mildly acidic (≡Si) 3 C–H. Poisoning studies show that both Lewis acidity and (≡Si) 3 C• are required for polymer pyrolysis reactivity. Finally, we propose that F-ASA promotes the formation of alkyl radicals in polymer melts, which are key intermediates in the thermal pyrolysis reactions of aliphatic polymers, involving the cooperative reactivity of both the Lewis acid and (≡Si) 3 C•.

aluminum↗

Crystallization Kinetics and Excess Free Energy of H2O and D2O Nanoscale Films of Amorphous Solid Water

Temperature-programmed desorption (TPD) and reflection absorption infrared spectroscopy (RAIRS) are used to investigate the crystallization kinetics and measure the excess free energy of metastable amorphous solid water films (ASW) of H2O and D2O grown using molecular beams. The desorption rates from the amorphous and crystalline phases of ASW are distinct, and as such, crystallization manifests can be observed in the TPD spectrum. The crystallization kinetics were studied by varying the TPD heating rate from 0.001 to 3 K/s. A coupled desorptioncrystallization kinetic model accurately simulates the desorption spectra and accurately predicts the observed temperature shifts in the crystallization. Isothermal crystallization studies using RAIRS are in agreement with the TPD results. Furthermore, highly sensitive measurements of the desorption rates were used to determine the excess free energy of ASW near 150 K. The excess entropy obtained from these data are consistent with there being a thermodynamic continuity between ASW and supercooled liquid water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

HCI Adsorption and Ionization on Amorphous and Crystalline H2O Films below 50 K

Molecular beams were used to grow amorphous and crystalline H2O films and to dose HCl on their surface. The adsorption state of HCl on the films was probed with infrared spectroscopy. The spectral signature of hydronium ions was observed only when the HCl adlayer was in direct contact with the solid water films at temperatures as low as 20 K. The spectral signature of solid HCl (amorphous or crystalline) was identified only after saturation of the adsorption sites in the first layer or when deposited onto a rare gas spacer layer between the HCl and water film. The Zundel continuum is also clearly observed when the first HCl adlayer is in contact with the thin solid water films. These observations strongly support the spontaneous ionic dissociation of the first layer HCl adsorbed onto the ice surface, and the subsequent condensation of solid HCl, as observed by Parent and coworkers. [F. Bournel et al. Physical Review B 2002, 65, 2014041] using synchrotron-based electron spectroscopy

74 ATOMIC AND MOLECULAR PHYSICS↗

Electronic Origin For The Phase Transition From Amorphous LixSi To Crystalline Li15Si4

Silicon has been widely explored as an anode material for lithium ion battery. Upon lithiation, silicon transforms to amorphous LixSi (a-LixSi) via electrochemical driven solid state amorphization. With increasing lithium concentration, a-LixSi transforms to crystalline Li15Si4 (c-Li15Si4). The mechanism of this crystallization process is not known. In this paper, we report the fundamental characteristics of the phase transition of a-LixSi to c-Li15Si4 using in-situ scanning transmission electron microscopy (STEM), electron energy loss spectroscopy (EELS), and density function theory (DFT) calculation. We find that when the lithium concentration in a-LixSi reaches a critical value of x = 3.75, the a-Li3.75Si spontaneously and congruently transforms to c-Li15Si4 by a process that is solely controlled by the lithium concentration in the a-LixSi, involving neither large scale atomic migration nor phase separation. DFT calculations indicate that c-Li15Si4 formation is favored over other possible crystalline phases due to the similarity in electronic structure with a-Li3.75Si.

Environmental Molecular Sciences Laboratory↗

Electron-beam-assisted superplastic shaping of nanoscale amorphous silica

Glasses are usually shaped through the viscous fl ow of a liquid before its solidifi cation, as practiced in glass blowing. At or near room temperature (RT), oxide glasses are known to be brittle and fracture upon any mechanical deformation for shape change. Here, we show that with moderate exposure to a low-intensity ( < 1.8 × 10-2 A cm-2 ) electron beam (e-beam), dramatic shape changes can be achieved for nanoscale amorphous silica, at low temperatures and strain rates > 10- 4 per second. We show not only large homogeneous plastic strains in compression for nanoparticles but also superplastic elongations > 200 % in tension for nanowires (NWs). We also report the fi rst quantitative comparison of the load-displacement responses without and with the e-beam, revealing dramatic difference in the fl ow stress (up to four times). This e-beam-assisted superplastic deformability near RT is useful for processing amorphous silica and other conventionally-brittle materials for their applications in nanotechnology.

36 MATERIALS SCIENCE↗

Direct growth of single-crystalline III–V semiconductors on amorphous substrates

The III–V compound semiconductors exhibit superb electronic and optoelectronic properties. Traditionally, closely lattice-matched epitaxial substrates have been required for the growth of high-quality single-crystal III–V thin films and patterned microstructures. To remove this materials constraint, here we introduce a growth mode that enables direct writing of single-crystalline III–V’s on amorphous substrates, thus further expanding their utility for various applications. The process utilizes templated liquid-phase crystal growth that results in user-tunable, patterned micro and nanostructures of single-crystalline III–V’s of up to tens of micrometres in lateral dimensions. InP is chosen as a model material system owing to its technological importance. The patterned InP single crystals are configured as high-performance transistors and photodetectors directly on amorphous SiO 2 growth substrates, with performance matching state-of-the-art epitaxially grown devices. In conclusion, the work presents an important advance towards universal integration of III–V’s on application-specific substrates by direct growth.

36 MATERIALS SCIENCE↗

Reversibility and criticality in amorphous solids

The physical processes governing the onset of yield, where a material changes its shape permanently under external deformation, are not yet understood for amorphous solids that are intrinsically disordered. Here, using molecular dynamics simulations and mean-field theory, we show that at a critical strain amplitude the sizes of clusters of atoms undergoing cooperative rearrangements of displacements (avalanches) diverges. We compare this non-equilibrium critical behaviour to the prevailing concept of a ‘front depinning’ transition that has been used to describe steady-state avalanche behaviour in different materials. We explain why a depinning-like process can result in a transition from periodic to chaotic behaviour and why chaotic motion is not possible in pinned systems. As a result, these findings suggest that, at least for highly jammed amorphous systems, the irreversibility transition may be a side effect of depinning that occurs in systems where the disorder is not quenched.

36 MATERIALS SCIENCE↗

Enhanced piezoelectricity from highly polarizable oriented amorphous fractions in biaxially oriented poly(vinylidene fluoride) with pure β crystals

Piezoelectric polymers hold great potential for various electromechanical applications, but only show low performance, with |d 33 |< 30 pC/N. We prepare a highly piezoelectric polymer (d 33 = -62 pC/N) based on a biaxially oriented poly(vinylidene fluoride) (BOPVDF, crystallinity = 0.52). After unidirectional poling, macroscopically aligned samples with pure β crystals are achieved, which show a high spontaneous polarization (P s ) of 140 mC/m 2 . Given the theoretical limit of P s,β = 188 mC/m 2 for the neat β crystal, the high P s cannot be explained by the crystalline-amorphous two-phase model (i.e., P s,β = 270 mC/m 2 ). Instead, we deduce that a significant amount (at least 0.25) of an oriented amorphous fraction (OAF) must be present between these two phases. Experimental data suggest that the mobile OAF resulted in the negative and high d 33 for the poled BOPVDF. The plausibility of this conclusion is supported by molecular dynamics simulations.

36 MATERIALS SCIENCE↗

Liquid-liquid phase separation in supercooled water from ultrafast heating of low-density amorphous ice

Recent experiments continue to find evidence for a liquid-liquid phase transition (LLPT) in supercooled water, which would unify our understanding of the anomalous properties of liquid water and amorphous ice. These experiments are challenging because the proposed LLPT occurs under extreme metastable conditions where the liquid freezes to a crystal on a very short time scale. Here, we analyze models for the LLPT to show that coexistence of distinct high-density and low-density liquid phases may be observed by subjecting low-density amorphous (LDA) ice to ultrafast heating. We then describe experiments in which we heat LDA ice to near the predicted critical point of the LLPT by an ultrafast infrared laser pulse, following which we measure the structure factor using femtosecond x-ray laser pulses. Consistent with our predictions, we observe a LLPT occurring on a time scale <100 ns and widely separated from ice formation, which begins at times >1 μs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Substantial lifetime enhancement for Si-based photoanodes enabled by amorphous TiO2 coating with improved stoichiometry

Abstract Amorphous titanium dioxide (TiO 2 ) film coating by atomic layer deposition (ALD) is a promising strategy to extend the photoelectrode lifetime to meet the industrial standard for solar fuel generation. To realize this promise, the essential structure-property relationship that dictates the protection lifetime needs to be uncovered. In this work, we reveal that in addition to the imbedded crystalline phase, the presence of residual chlorine (Cl) ligands is detrimental to the silicon (Si) photoanode lifetime. We further demonstrate that post-ALD in-situ water treatment can effectively decouple the ALD reaction completeness from crystallization. The as-processed TiO 2 film has a much lower residual Cl concentration and thus an improved film stoichiometry, while its uniform amorphous phase is well preserved. As a result, the protected Si photoanode exhibits a substantially improved lifetime to ~600 h at a photocurrent density of more than 30 mA/cm 2 . This study demonstrates a significant advancement toward sustainable hydrogen generation.

36 MATERIALS SCIENCE↗