Search NASA⌕ Search

SEARCH · Search NASA

Results for “Analyzer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

Effects of specimen preparation on the electromagnetic property measurements of solid materials with an automatic network analyzer

Effects of specimen preparation on measured values of an acrylic's electomagnetic properties at X-band microwave frequencies, TE sub 1,0 mode, utilizing an automatic network analyzer have been studied. For 1 percent or less error, a gap between the specimen edge and the 0.901-in. wall of the specimen holder was the most significant parameter. The gap had to be less than 0.002 in. The thickness variation and alignment errors in the direction parallel to the 0.901-in. wall were equally second most significant and had to be less than 1 degree. Errors in the measurement f the thickness were third most significant. They had to be less than 3 percent. The following parameters caused errors of 1 percent or less: ratios of specimen-holder thicknesses of more than 15 percent, gaps between the specimen edge and the 0.401-in. wall less than 0.045 in., position errors less than 15 percent, surface roughness, hickness variation in the direction parallel to the 0.401-in. wall less than 35 percent, and specimen alignment in the direction parallel to the 0.401-in. wall mass than 5 degrees.

Long, E. R., Jr.↗

Boundary force method for analyzing two-dimensional cracked bodies

The Boundary Force Method (BFM) was formulated for the two-dimensional stress analysis of complex crack configurations. In this method, only the boundaries of the region of interest are modeled. The boundaries are divided into a finite number of straight-line segments, and at the center of each segment, concentrated forces and a moment are applied. This set of unknown forces and moments is calculated to satisfy the prescribed boundary conditions of the problem. The elasticity solution for the stress distribution due to concentrated forces and a moment applied at an arbitrary point in a cracked infinite plate are used as the fundamental solution. Thus, the crack need not be modeled as part of the boundary. The formulation of the BFM is described and the accuracy of the method is established by analyzing several crack configurations for which accepted stress-intensity factor solutions are known. The crack configurations investigated include mode I and mixed mode (mode I and II) problems. The results obtained are, in general, within + or - 0.5 percent of accurate numerical solutions. The versatility of the method is demonstrated through the analysis of complex crack configurations for which limited or no solutions are known.

Tan, P. W.↗

Comparison of the STI NIPIP tracking dynamics identification with the on-line Fourier analyzer DFA results including a time varying case

The Non-Intrusive Pilot Identification Procedure (NIPIP) recently developed at STI and described at the 1981 Annual Manual was used to identify operators who were compensatory tracking a sub-critical-instability task. NIPIP uses a time domain least squares procedure converting to frequency domain coefficients. The forcing function was a sum of sinusoids supplied by the STI Mark II Describing Function Analyzer, which computes on-line Fourier coefficients of the operator's error/input describing function. The resulting open-loop and operator dynamics computed by each procedure are compared, and they are shown to be reasonably close when there is reasonable power in the error signal at the measurement frequencies. A special run was made in which the operator abruptly reduced gain within 1 sec, and the ability of the NIPIP to identify this step time variation in the operator is illustrated.

Jex, H. R.↗

Analyzing Wakes From Hovering-Helicopter Rotor Blades

New method for analyzing free wake of hovering-helicopter rotor produces more reliable results and requires less computer time. Copes with wake instabilities, both physical and numerical, that afflict usual time-stepping analysis methods. Tip-vortex position, in coordinates moving with rotor blade, updated in relaxation procedure. Wake-airflow solution reached when updates converge to steady wake shape.

Bliss, D. B.↗

Finite wordlength implementation of a megachannel digital spectrum analyzer

The results of an extensive system analysis of the megachannel spectrum analyzer currently being developed for use in various applications of the Deep Space Network are presented. The intent of this analysis is to quantify the effects of digital quantization errors on system performance. The results of this analysis provide useful guidelines for choosing various system design parameters to enhance system performance.

Satorius, E. H.↗

Stratified processes to analyze SSME parts and subsystems using Weibull methodology

Due to the various parts found in a Space Shuttle Main Engine (SSME), analyzation of every part is not feasible or needed. Based on previous mathematical modeling experience of high velocity cryogenic equipment, the environmental traits of location of the part, temperature range, fluid velocity, pressure range, and elevation variation of fluid flow as being significant factors were determined. Six parts categories were developed. The part categories are: (1) fuel turbomachinery, (2) oxidizer, (3) combustion devices, (4) valves, (5) ducts, and (6) lines. Due to a suspicion that superficial failure modes exist, six status codes were developed. The codes are: (1) part is in service presently, (2) part is out-of-service due to its own failure, (3) part is out-of-service due to engine (or some other part failure), (4) part is out-of-service because it's retired/obsolete (time related), (5) never fired-scrapped due to own problem or part is store, and (6) part is out-of-service for repair. It was suggested that to properly model failure behavior of SSME parts that: (1) significant factors contributing to failure must be examined, (2) relatively precision based on real life data must be examined, and (3) alternative definitions of failure must be initialized by the engineers.

Gray, Lou Allen Bell↗

A synchronous data analyzer for the Minimum Delay Data Format (MDDF) and Launch Trajectory Acquisition System (LTAS)

The Synchronous Data Analyzer gives its user an independent source for checking the validity of raw MDDF and LTAS data. Its ability to produce real-time displays comprised of decoded parameters as well as its ability to capture several frames for non-real-time display makes it a valuable tool for monitoring and troubleshooting applications involving these data formats. Its composition of portable firmware and mostly commercial hardware makes it a low cost, easily fabricated product.

Green, Andrew J.↗

Image processing system to analyze droplet distributions in sprays

An image processing system was developed which automatically analyzes the size distributions in fuel spray video images. Images are generated by using pulsed laser light to freeze droplet motion in the spray sample volume under study. This coherent illumination source produces images which contain droplet diffraction patterns representing the droplets degree of focus. The analysis is performed by extracting feature data describing droplet diffraction patterns in the images. This allows the system to select droplets from image anomalies and measure only those droplets considered in focus. Unique features of the system are the totally automated analysis and droplet feature measurement from the grayscale image. The feature extraction and image restoration algorithms used in the system are described. Preliminary performance data is also given for two experiments. One experiment gives a comparison between a synthesized distribution measured manually and automatically. The second experiment compares a real spray distribution measured using current methods against the automatic system.

Bertollini, Gary P.↗

Effects of non-spherical drops on a phase Doppler spray analyzer

A phase/Doppler spray analyzer (P/DSA) and a laser imaging system was used to study the response of a P/DSA to nonspherical particles. Methanol particles with an aspect ratio ranging from 0.7 to 1.4 were used in this investigation. Results indicated that the P/DSA was quite sensitive to particle shape. A Berglund-Liu generator was used to produce particles of 98 microns (volumetric diameter). The P/DSA instrument measured particle sizes ranging from 142 microns for a particle of aspect ratio 0.7, to 84 microns for an aspect ratio of 1.4. Particle diameters based on averaged x and y diameters for the laser imaging system ranged from 95 microns to 92 microns over the same range of aspect ratios.

Alexander, D. R.↗

Analysis of Martian ionosphere and solar wind electron gas data from the planar retarding potential analyzer on the Viking spacecraft

Approximate expressions for the electron current collected by a planar retarding potential analyzer (RPA) mounted on a moving, conducting, charged spacecraft are derived. They are utilized for the analysis of electron current data obtained by the RPAs on the Viking spacecraft in the ionosphere of Mars and in the disturbed and undisturbed solar wind near this planet. It is shown that contamination currents by photoelectrons emitted from the spacecraft can be distinguished and removed from the signal. Parameters deduced from the analysis of RPA electron sampling data are the multicomponent electron temperatures, the number densities, and the spacecraft potential.

Mantas, G. P.↗

SINDA - Systems Improved Numerical Differencing Analyzer

Capability to model fluid flow added. SINDA is software system developed to solve physical problems governed by diffusion-type equations mathematically modeled by lumped-parameter representations. Used as general thermal analyzer with resistor-and-capacitor-network representations. Adapted to wide range of problems represented by Fourier, Possion, Laplace, or other differential equations. Written in FORTRAN and Assembler.

Damico, Steve J.↗

CONFIG: Qualitative simulation tool for analyzing behavior of engineering devices

To design failure management expert systems, engineers mentally analyze the effects of failures and procedures as they propagate through device configurations. CONFIG is a generic device modeling tool for use in discrete event simulation, to support such analyses. CONFIG permits graphical modeling of device configurations and qualitative specification of local operating modes of device components. Computation requirements are reduced by focussing the level of component description on operating modes and failure modes, and specifying qualitative ranges of variables relative to mode transition boundaries. Simulation processing occurs only when modes change or variables cross qualitative boundaries. Device models are built graphically, using components from libraries. Components are connected at ports by graphical relations that define data flow. The core of a component model is its state transition diagram, which specifies modes of operation and transitions among them.

Malin, Jane T.↗

The composite blade structural analyzer (COBSTRAN)

The use and application of the COBSTRAN (COmposite Blade STRuctural ANalyzer) computer code is presented. COBSTRAN was developed at NASA-Lewis and is currently being used for the design and analysis of aircraft engine ducted and unducted fan blades. The features of COBSTRAN are demonstrated for the modeling and analysis of a scaled down wind tunnel model propfan blade made from fiber composites. Comparison of analytical and experimental mode shapes and frequencies are shown, verifying the model development and analysis techniques used. The methodologies and programs developed for this analysis are directly applicable to other propfan blades.

Aiello, Robert A.↗

Features and applications of the integrated composites analyzer (ICAN) code

The thermal behavior of composite spacecraft antenna reflectors was investigated with the Integrated Composites Analyzer (ICAN) computer code. Parametric studies were conducted on the face sheets and honeycomb core which constitute the sandwich-type structures. Selected thermal and mechanical properties of the composite faces and sandwich structures are presented graphically as functions of varying fiber volume ratio, laminate configuration, fabrication factors, and environmental conditions.

Ginty, Carol A.↗

METCAN: The metal matrix composite analyzer

Metal matrix composites (MMC) are the subject of intensive study and are receiving serious consideration for critical structural applications in advanced aerospace systems. MMC structural analysis and design methodologies are studied. Predicting the mechanical and thermal behavior and the structural response of components fabricated from MMC requires the use of a variety of mathematical models. These models relate stresses to applied forces, stress intensities at the tips of cracks to nominal stresses, buckling resistance to applied force, or vibration response to excitation forces. The extensive research in computational mechanics methods for predicting the nonlinear behavior of MMC are described. This research has culminated in the development of the METCAN (METal Matrix Composite ANalyzer) computer code.

Hopkins, Dale A.↗

Digital avionics design and reliability analyzer

The description and specifications for a digital avionics design and reliability analyzer are given. Its basic function is to provide for the simulation and emulation of the various fault-tolerant digital avionic computer designs that are developed. It has been established that hardware emulation at the gate-level will be utilized. The primary benefit of emulation to reliability analysis is the fact that it provides the capability to model a system at a very detailed level. Emulation allows the direct insertion of faults into the system, rather than waiting for actual hardware failures to occur. This allows for controlled and accelerated testing of system reaction to hardware failures. There is a trade study which leads to the decision to specify a two-machine system, including an emulation computer connected to a general-purpose computer. There is also an evaluation of potential computers to serve as the emulation computer.

Source record↗

An improved boundary force method for analyzing cracked anisotropic materials

The Boundary Force Method (BFM), a form of indirect boundary element method, is used to analyze composite laminates with cracks. The BFM uses the orthotropic elasticity solution for a concentrated horizontal and vertical force and a moment applied at a point in a cracked, infinite sheet as the fundamental solution. The necessary stress functions for this fundamental solution were formulated using the complex variable theory of orthotropic elasticity. The current method is an improvement over a previous method using only forces and no moment. The improved method was verified by comparing it to accepted solutions for a finite-width, center-crack specimen subjected to uniaxial tension. Four graphite/epoxy laminates were used: (0 + or - 45/90)sub s, (0), (+ or - 45)sub s, and (+ or - 30)sub s. The BFM results agreed well with accepted solutions. Convergence studies showed that with the addition of the moment in the fundamental solution, the number of boundary elements required for a converged solution was significantly reduced. Parametric studies were done for two configurations for which no orthotropic solutions are currently available; a single edge crack and an inclined single edge crack.

Tan, Paul W.↗

Boundary force method for analyzing two-dimensional cracked plates

The Boundary Force Method (BFM) was formulated for the two-dimensional stress analysis of complex crack configurations. In this method, only the boundaries of the region of interest are modeled. The boundaries are divided into a finite number of straight-line segments, and at the center of each segment, concentrated forces and a moment are applied. This set of unknown forces and moments is calculated to satisfy the prescribed boundary conditions of the problem. The elasticity solution for the stress distribution due to concentrated forces and a moment applied at an arbitrary point in a cracked infinite plate are used as the fundamental solution. Thus, the crack need not be modeled as part of the boundary. The formulation of the BFM is described and the accuracy of the method is established by analyzing several crack configurations for which accepted stress-intensity factor solutions are known. The crack configurations investigated include mode I and mixed mode (mode I and II) problems. The results obtained are, in general, within + or - 0.5 percent of accurate numerical solutions. The versatility of the method is demonstrated through the analysis of complex crack configurations for which limited or no solutions are known.

Tan, Paul W.↗